CYLINDRO III DECORATIVE LED WITH OPAL ACRYLIC DIFFUSER
TYPE :
PROJECT:
ORDER NUMBER:
Select
Select
Select
Select
Model#
Finish
LEDs
Option
Mount
6803 –3 ft.
6804 –4 ft.
6805 –5 ft.
S – Silver
W –White
K– Black
SQ–RGB
R–Red
B–Blue
C2RD
BDMXMOD
S –Separate
C – Central
Example:
6805
W
SQ
Traxon Light Drive* (enter quantity)
Qty
Qty BTRAXW (white)BTRAXB
(black)
• Mounts to all standard JBoxes.
• Available in separate or central
mount (see drawings, right).
•Specify C2RD for remote driver
compartment in accessible
ceiling or through access panel.
•Specify C2RDS (separate)
or C2RDC (central) mount with
remote driver installation.
6800
LED, Separate Mount
6 5/8
CONSTRUCTION
• Extruded aluminum inner
housing with white frosted
acrylic outer diffuser.
6’ adjustable power cord and
AC cables with push button
grippers supplied standard.
(Specify XP for additional
length.)
3’ / 4’ / 5’
6800
LED, Central Mount
LED DRIVERS
• Constant voltage, 100W/24V
universal for SQ –RGB
sequencer.
• 60W/12V driver for single color
(Red or Blue) LEds.
• Electronic drivers, DMX and
dimmer interface housed in
canopy or remote gear box
(C2RD), for easy access.
• Standard LED color options
include red and blue, as well as
RGB sequencing, controlled
with a DMX 512 interface
(BDMXMOD). Optional wall box
control offered separately (see
Traxon, back page.)
LEDs
• Flexible 5050 universal voltage
LED tape light.
• 24V for SQ –RGB sequencer;
12V for single color (Red or
Blue) LEDs.
• cUL listed for dry locations
only.
6 5/8
3’ / 4’ / 5’
Model Length WhiteRed/BlueSQ
WattsWatts Watts
6803
6804
6805
3 ft.
4 ft.
5 ft.
36
54
72
1836
27
54
36
72
Specify LED color:
SQ – RGB sequencer
Red
Blue
C
BURBANK,
CALIFORNIA,
DIMENSIONS
Model
ID
OD
91505
6803 30“35.981“
W W W.
6804 42.125“47.625“
DELRAY
6805 53.75“59.625“
LIGHTING.
COM
NOV 2015
CANOPY
BDMXMOD
cylindro iii.deco
Select
CYLINDRO III . DECO
Delray’s Deco fixtures are cost-effective color LED luminaires, available in a
variety of classic shapes and geometric configurations. Deco fixtures feature
flexible 5050 universal voltage LED tape light; the most popular type of commercial LED light source available and, therefore, easily obtained and replaced.
24V for SQ –RGB sequencer; 12V for single color (Red or Blue) LEDs.
6800
CP DISTRIBUTION
N/A
Deco standard LED color options include red and blue, as well as RGB
sequencing, controlled with a DMX 512 interface (see BDMXMOD, below).
Optional wall box control offered separately (see Traxon, below).
Deco fixtures deliver subtle decorative effects with Delray’s lowest lumens,
wattage, and cost.
REMOTE DRIVER
Driver must be accessible after
installation.For suspended and
hard lid ceilings with access panels.
Canopy mounts to mud ring
attached to J-box. For separate
mount, order C2RDS.
0000000000000
000000000000000
cUL listed for dry locations only.
BDMXMOD
• Osram part no. OTDMXRGB supplied.
• DMX control interface for RGB LED.
• Provides DMX control with protocols that meet USITT DMX-512A
or DMX512 (DIN 56930-2). No converter is required. DMX controls
by others.
• A second 4-conductor control cable to fixture canopy is supplied.
Remote Driver Mount
Multiple drivers must be mounted no less than 4 inches apart side-by-side,
and 1 inch apart end-to-end, to avoid overheating.
TRAXON LIGHT-DRIVE RGB (order separately)
COEFFICIENTS
BTRAXW –white controller
BTRAXB –black controller (shown)
• Standalone, wall-mounted
(12V power supply included)
DMX controller for RGB
LED that provides direct access
to fixtures.
• Tune color and brightness with
the Light-Drive wheel.
NOTE : Aircraft cable
suspension not recommended
for outdoor use, where fixture
will be exposed to water,
or subject to wind oscillation.
Avoid use near HVAC vents
and in environments with
corrosive chemical vapors,
such as swimming pools.
• Two sequence modes enable
continuous replay of all saved
color settings, as well as a preset
color-phase function, which can
be adjusted in replay speed.
• Fully dimmable white
mode button.
• See www.traxon-usa.com
for details.
Central mount remote driver
installation. Order C2RDC.
Max. Wiring Distance (at full load)
Wire Size (AWG)Distance (ft.)
18
16
14
12
10
18
29
46
71
120
NOTE: Multiple drivers must be
mounted no less than 4 inches
apart side-by-side, and 1 inch
apart end-to-end, to avoid
overheating.
ACRYLIC DIFFUSER CLEANING
Warning: Do not clean with
ammonia based cleaners
(e.g. Windex®). Use only water
or cleaners specifically formulated
for cleaning plastics.
NOV 2015
RGB INTERFACE CONTROL OPTIONS
N/A
OPTIONS
00
LED