Licensing the Cisco ASR 900 Series Routers
First Published: July 30, 2013
Last Modified: June 04, 2014
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-30223-02
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version
of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://
www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
© 2013-2014
Cisco Systems, Inc. All rights reserved.
CONTENTS
CHAPTER 1
New and Changed Information 1
CHAPTER 2
Licensing the OC-3 and OC-12 Interface Modules 3
Restrictions for Licensing the Ports on the OC-3 and OC-12 Interface Module 3
Information About Licensing the Cisco ASR 900 Series Routers 3
Licensing the OC-3 and OC-12 Interface Modules 4
Installing and Upgrading Licenses on the OC-3 and OC-12 Interface Modules 5
Enabling Ports on the Slot 7
Uninstalling the License on OC-3 and OC-12 Interface Modules 8
Verifying the Licenses 9
CHAPTER 3
Right To Use Licensing 11
Restrictions for using RTU Licenses 11
Information About Licensing the Cisco ASR 900 Series Routers 12
Right to Use License Support for Cisco ASR 900 Series Routers 12
Advantages of RTU Licenses 12
Right To Use Licenses for Cisco ASR 900 Series 12
Migration of Existing Licenses to RTU Licenses 13
Configuring the Right to Use License 13
Activating the Right to Use License 14
Verifying the RTU Licenses 15
Licensing the Cisco ASR 900 Series Routers
OL-30223-02
iii
Contents
Licensing the Cisco ASR 900 Series Routers
iv
OL-30223-02
CHAPTER
1
New and Changed Information
Table 1: New and Changed Features
Feature
Description
ASR 903 RSP1
Module
ASR903 RSP2 Module
ASR 902
Where
Documented
Port Licensing for This features
Cisco IOS XE
OC-3 and OC-12 introduces
Release 3.10S
Interface Modules licensing for the
OC-3 and OC-12
interface module
on the Cisco ASR
900 Series
Routers.
Cisco IOS XE Release Cisco IOS XE Release Licensing the
3.13S
3.11S
OC-3 and OC-12
Interface
Modules, on page
4
Right to Use
(RTU) license
Cisco IOS XE Release Cisco IOS XE Release Right to Use
3.13S
3.11S
License Support
for Cisco ASR 900
Series Routers, on
page 12
This features
Cisco IOS XE
introduces support Release 3.12S
for RTU licenes
on the Cisco ASR
900 Series Routers
Licensing the Cisco ASR 900 Series Routers
OL-30223-02
1
New and Changed Information
Licensing the Cisco ASR 900 Series Routers
2
OL-30223-02
CHAPTER
2
Licensing the OC-3 and OC-12 Interface Modules
The Cisco Software License Activation feature is a set of processes and components to activate Cisco IOS
software feature sets by obtaining and validating fee-based Cisco software licenses.
For information on software license activation and concepts, see the Cisco IOS Software Activation Conceptual
Overview.
For information on obtaining and installing licenses, see Configuring the Cisco IOS Software Activation
Feature.
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest feature
information and caveats, see the release notes for your platform and software release.
Use Cisco Feature Navigator to find information about platform support and Cisco IOS, Catalyst OS, and
Cisco IOS XE software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/
cfn. An account on Cisco.com is not required.
• Restrictions for Licensing the Ports on the OC-3 and OC-12 Interface Module, page 3
• Information About Licensing the Cisco ASR 900 Series Routers, page 3
• Installing and Upgrading Licenses on the OC-3 and OC-12 Interface Modules, page 5
• Verifying the Licenses, page 9
Restrictions for Licensing the Ports on the OC-3 and OC-12
Interface Module
• The 1 OC12 port license can only be enabled on port 0 of the OC-3 or OC-12 interface module.
Information About Licensing the Cisco ASR 900 Series Routers
For information on software activation and license procedures, see Software Activation Configuration Guide,
Cisco IOS XE Release 3S (Cisco ASR 903).
Licensing the Cisco ASR 900 Series Routers
OL-30223-02
3
Licensing the OC-3 and OC-12 Interface Modules
Licensing the OC-3 and OC-12 Interface Modules
Licensing the OC-3 and OC-12 Interface Modules
The optical modules 4-Port OC3/STM-1 or 1-Port OC12/STM-4 delivers four active ports of OC-3 interface
module (IM) or Synchronous Transport Module level 1 (STM-1) connectivity, or one active port of OC-12
IM or STM-4 connectivity, on the Cisco ASR 903 Router. Licensing is applicable to these ports on the interface
modules.
The benefits of licensing these ports are:
• Pay-as-you-grow model to enhance the ports by purchasing licenses as required.
• Ability to shift license from one port to another.
• Ability to release a license when the interface module is removed from a slot and reinstall the license
when inserted again.
• Support for high availability and OIR of interface modules.
Note
For more information on installing the OC-3 and OC-12 interface modules, see the Cisco ASR 903 Series
Aggregation Services Router Hardware Installation Guide.
These
are guidelines for licensing the ports:
• Two types of licenses are available for the OC-3 and OC-12 IMs.
• Each port can have only one license at a given point of time.
• Each port needs one license and each license can be used for any of the ports.
• If the card type is changed from OC-3 to OC-12 or vice versa
, the license installed on the card is automatically released and the new card type uses the license.
Note
The OC-12 port license works only on the first port of the IM. U
nless there is a license enabled on the port, no configuration can be performed on the
port.
Table 2: OC-3 and OC-12 Port Licenses
License Type
Description
Usability
1 OC3 port license
Single OC3/STM-1 port
STM-1 on OC-3 port
1 OC12 port license
Single OC12/STM-4 port
STM-1 on OC-3 port
Licensing the Cisco ASR 900 Series Routers
4
OL-30223-02
Licensing the OC-3 and OC-12 Interface Modules
Installing and Upgrading Licenses on the OC-3 and OC-12 Interface Modules
Note
Licenses are not mapped to any port. All the licenses are in a pool. Licenses can be used to enable any
port as long as there are sufficient number of licenses.
Moving Licenses Across Ports
The licenses are not tied to a port and can moved across the ports and interface modules.
For example, if there are four licenses, and we have two interface modules (IM) and four ports, the licenses
are distributed to the first IM on slot 0 and second IM on slot 1.
Platform enable controller sonet 0/0/0
Platform enable controller sonet 0/0/1
Platform enable controller sonet 0/1/0
Platform enable controller sonet 0/1/1
OC-3 and OC-12 Interface Module Online Insertion and Removal (OIR)
If an OIR is performed on the enabled port or controller of the interface module, the license used by the
interface module is released. When the interface module is inserted again, the license which was valid before
the OIR is re-enabled (assuming that there are non-zero usable ports).
OC-3 and OC-12 Interface Module Stateful Switchover (SSO)
If the license is installed on an active port and enabled on the active RSP module, the license information is
synchronized with the standby RSP module. On SSO, the license ports enabled on the active RSP are activated
on the standby RSP module.
An port license ISSU upgrade from an unsupported release to a supported release may impact the traffic flow
on the router. If the controllers before the ISSU are in UP state, after an upgrade the controllers might remain
in DOWN state, until the license in installed and enabled on the ports
Reload of Cisco ASR 903
A router reload may not be required after the license in installed on the ports. However, if the router is reloaded,
the ports that are enabled prior to the reload will retain the license and configuration.
Installing and Upgrading Licenses on the OC-3 and OC-12
Interface Modules
Before You Begin
Read and understand the license activation process concepts in the in the “Cisco IOS Software Activation
Conceptual Overview” module.
To install or upgrade a license by using the license install command, you must have already received the
license file from the Cisco Product License Registration portal at http://www.cisco.com/go/license (or you
already backed up the license by using the license save command).
If you use Microsoft Entourage and receive the license file from Cisco in an e-mail attachment, the license
file will contain UTF-8 marking. These extra bytes in the license file cause it to be unusable during license
installation. To work around this issue, you can use a text editor to remove the extra characters and then install
Licensing the Cisco ASR 900 Series Routers
OL-30223-02
5
Licensing the OC-3 and OC-12 Interface Modules
Installing and Upgrading Licenses on the OC-3 and OC-12 Interface Modules
the license file. For more information about UTF-8 encoding, go to this URL: http://www.w3.org/International/
questions/qa-utf8-bom.
Note
The installation process does not install duplicate licenses. This message appears when duplicate licenses
are detected:
Installing...Feature:xxx-xxx-xxx...Skipped:Duplicate
Note
A standby device reboots twice when there is a mismatch of licenses.
SUMMARY STEPS
1. enable
2. show license udi
3. Convert the PAK to a license by entering the PAK and the UDI into the Cisco Product License Registration
portal: http://www.cisco.com/go/license.
4. license install stored-location-url
5. show license detail
6. end
DETAILED STEPS
Step 1
Command or Action
Purpose
enable
Enables privileged EXEC mode.
• Enter your password if prompted.
Example:
Device> enable
Step 2
show license udi
Displays all the UDI values that can be licensed in a system.
• You need the UDI of the device as part of the process to
obtain a license.
Example:
Device# show license udi
Step 3
Convert the PAK to a license by entering the PAK After entering the appropriate information, you will receive an
and the UDI into the Cisco Product License
e-mail containing the license information that you can use to install
the license:
Registration portal: http://www.cisco.com/go/
license.
• Copy the license file received from the Cisco Product License
Registration portal to the appropriate file system on the device.
or
• Click the Install button on the web page.
Licensing the Cisco ASR 900 Series Routers
6
OL-30223-02
Licensing the OC-3 and OC-12 Interface Modules
Enabling Ports on the Slot
Step 4
Command or Action
Purpose
license install stored-location-url
Installs the license. Accept the end-user license agreement if
prompted.
Example:
Router# license install bootflash:*.lic
Step 5
show license detail
Displays the license information and verifies the number of licenses
obtained.
Example:
Router# show license detail
Step 6
Returns to privileged EXEC mode.
end
Example:
Router# end
What to Do Next
You need to enable the ports on the interface module slot for the license to take effect.
Enabling Ports on the Slot
After installing and verifying the licenses on the router, enable the ports on the router.
Note
The no platform enable controller disables the ports on the interface module.
SUMMARY STEPS
1. enable
2. configure terminal
3. platform enable controller controller-type slot/subslot/port
4. controller sonet controller controller-type slot/subslot/port
5. no shutdown
6. end
DETAILED STEPS
Step 1
Command or Action
Purpose
enable
Enables privileged EXEC mode.
Enter your password if prompted.
Example:
Router> enable
Licensing the Cisco ASR 900 Series Routers
OL-30223-02
7
Licensing the OC-3 and OC-12 Interface Modules
Uninstalling the License on OC-3 and OC-12 Interface Modules
Step 2
Command or Action
Purpose
configure terminal
Enters global configuration mode.
Example:
Router# configure terminal
Step 3
platform enable controller controller-type
slot/subslot/port
Example:
Router(config)# platform enable controller
sonet 0/1/2
Step 4
controller sonet controller controller-type
slot/subslot/port
Enables the ports on slot where the interface is present.
Note
The slot number for the controller sonet is always
zero on the Cisco ASR 903 Router.
• controller—Configures a specific controller
• controller-type—Type of controller.
Selects the controller to configure and enters controller
configuration mode.
Example:
Router(config)# controller sonet 0/1/2
Step 5
no shutdown
Enables the controller.
Example:
Router(config-controller)# no shutdown
Step 6
Returns to privileged EXEC mode.
end
Example:
Router# end
Uninstalling the License on OC-3 and OC-12 Interface Modules
SUMMARY STEPS
1. enable
2. configure terminal
3. no platform enable controller controller-type slot/subslot/port
4. license clear feature-name
5. end
DETAILED STEPS
Step 1
Command or Action
Purpose
enable
Enables privileged EXEC mode.
Licensing the Cisco ASR 900 Series Routers
8
OL-30223-02
Licensing the OC-3 and OC-12 Interface Modules
Verifying the Licenses
Command or Action
Purpose
Enter your password if prompted.
Example:
Router> enable
Step 2
configure terminal
Enters global configuration mode.
Example:
Router# configure terminal
Step 3
no platform enable controller controller-type
slot/subslot/port
Uninstalls the licenses on the controllers for the feature.
Example:
Router# no platform enable controller sonet
0/1/2
Step 4
license clear feature-name
Example:
Removes a license entry from license storage once it has
been verified that the license line is valid and was explicitly
installed.
Router# license clear oc3
Step 5
Returns to privileged EXEC mode.
end
Example:
Router# end
Verifying the Licenses
• show license detail
Use the show license detail command to view the license on the ports.
Router# show license detail
Index: 4
Feature: oc3
License Type: Permanent
License State: Active, Not in Use
License Count: 13/0/0 (Active/In-use/Violation)
License Priority: Medium
Store Index: 2
Store Name: Primary License Storage
Version: 1.0
• show license udi
Use the show license udi command to view the UDI details of the license.
Router# show license udi
SlotID
PID
SN
UDI
-------------------------------------------------------------------------------*6
ASR-903
FOX1637P0UB
ASR-903:FOX1637P0UB
Licensing the Cisco ASR 900 Series Routers
OL-30223-02
9
Licensing the OC-3 and OC-12 Interface Modules
Verifying the Licenses
Licensing the Cisco ASR 900 Series Routers
10
OL-30223-02
CHAPTER
3
Right To Use Licensing
The Cisco Software License Activation feature is a set of processes and components to activate Cisco IOS
software feature sets by obtaining and validating fee-based Cisco software licenses.
For information on software license activation and concepts, see the Cisco IOS Software Activation Conceptual
Overview.
For information on obtaining and installing licenses, see Configuring the Cisco IOS Software Activation
Feature.
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest feature
information and caveats, see the release notes for your platform and software release.
Use Cisco Feature Navigator to find information about platform support and Cisco IOS, Catalyst OS, and
Cisco IOS XE software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/
cfn. An account on Cisco.com is not required.
• Restrictions for using RTU Licenses, page 11
• Information About Licensing the Cisco ASR 900 Series Routers, page 12
• Configuring the Right to Use License, page 13
• Activating the Right to Use License, page 14
• Verifying the RTU Licenses, page 15
Restrictions for using RTU Licenses
• 1588 feature license is not supported with RTU.
• OC-3 and OC-12 port licenses are not supported with RTU. We recommend that you go with Pay As
You Grow model and purchase the license to use the feature.
Licensing the Cisco ASR 900 Series Routers
OL-30223-02
11
Right To Use Licensing
Information About Licensing the Cisco ASR 900 Series Routers
Information About Licensing the Cisco ASR 900 Series Routers
For information on software activation and license procedures, see Software Activation Configuration Guide,
Cisco IOS XE Release 3S (Cisco ASR 903).
Right to Use License Support for Cisco ASR 900 Series Routers
The RTU license starts as an evaluation license with a 60-day trial period and changes into a perpetual
“Right-To-Use” license after the expiry of the trial period.
The RTU license is shipped with the IOS software image, as a built-in evaluation license (60 days). Once the
trial usage period expires and license automatically is converted, you are required to accept the EULA (End
User License Agreement) while activating the license. You can verify the license change by executing the
show license command.
Syslog messages are generated on the 50th, 55th and 60th day of usage as a warning at the end of the evaluation
period and conversion to an RTU license
Note
Permanent licenses have precedence over RTU licenses and node-locked licenses have precedence over
RTU licenses.
In a HA setup, to move licenses to the Standby RSP from the active, enable the standby console enable
command.
Router(config)# configure terminal
Router(config)# redundancy
Router(config-red)# main-cpu
Router(config-r-mc)# standby console enable
Router(config-r-mc)# end
Advantages of RTU Licenses
• Offers simplified licensing approach.
• Licenses are converted to permanent licenses after the trial period.
Right To Use Licenses for Cisco ASR 900 Series
License Type
RTU
Base License
Metro Services
Yes
Metro IP Services
Yes
Metro Aggregation Services
Yes
Feature Licenses
Licensing the Cisco ASR 900 Series Routers
12
OL-30223-02
Right To Use Licensing
Configuring the Right to Use License
License Type
RTU
ATM
Yes
1588
No
OC-3 and OC-12 Port License
No
Migration of Existing Licenses to RTU Licenses
When you upgrade to RTU licenses, EULA acceptance prompts for fresh license activation. After the trial
period, the license is converted to a permanent license.
License Type
Migration to RTU License
Permanent license is installed
NA
Built-in evaluation license
New image boots with default license.
Temporary license generated by
SWIFT
No issues during migration. After license expiry period (temporary
license and RTU trial period), license is converted to permanent.
Configuring the Right to Use License
SUMMARY STEPS
1. enable
2. configure terminal
3. license right-to-use move {metroaggrservices | metroipservices | metroservices}
4. end
DETAILED STEPS
Step 1
Command or Action
Purpose
enable
Enables privileged EXEC mode.
Example:
• Enter your password if prompted.
Router> enable
Step 2
configure terminal
Enters global configuration mode.
Example:
Router# configure terminal
Licensing the Cisco ASR 900 Series Routers
OL-30223-02
13
Right To Use Licensing
Activating the Right to Use License
Step 3
Command or Action
Purpose
license right-to-use move {metroaggrservices |
metroipservices | metroservices}
Installs the RTU license. Accept the end-user license
agreement if prompted.
Example:
Router# license right-to-use move metroipservices
Step 4
Returns to privileged EXEC mode.
end
Example:
Router# end
Configuration Example
Router# license right-to-use move metroipservices
% End User License Agreement is not accepted
PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING THE LICENSE OR
LICENSE KEY PROVIDED FOR ANY CISCO PRODUCT FEATURE OR USING SUCH
PRODUCT FEATURE CONSTITUTES YOUR FULL ACCEPTANCE OF THE FOLLOWING
TERMS. YOU MUST NOT PROCEED FURTHER IF YOU ARE NOT WILLING TO BE BOUND
BY ALL THE TERMS SET FORTH HEREIN.
Use of this product feature requires an additional license from Cisco,
together with an additional payment. You may use this product feature
on an evaluation basis, without payment to Cisco, for 60 days. Your use
of the product, including during the 60 day evaluation period, is
subject to the Cisco end user license agreement
http://www.cisco.com/en/US/docs/general/warranty/English/EU1KEN_.html
If you use the product feature beyond the 60 day evaluation period, you
must submit the appropriate payment to Cisco for the license. After the
60 day evaluation period, your use of the product feature will be
governed solely by the Cisco end user license agreement (link above),
together with any supplements relating to such product feature. The
above applies even if the evaluation license is not automatically
terminated and you do not receive any notice of the expiration of the
evaluation period. It is your responsibility to determine when the
evaluation period is complete and you are required to make payment to
Cisco for your use of the product feature beyond the evaluation period.
Your acceptance of this agreement for the software features on one
product shall be deemed your acceptance with respect to all such
software on all Cisco products you purchase which includes the same
software. (The foregoing notwithstanding, you must purchase a license
for each software.
Activating the Right to Use License
SUMMARY STEPS
1. enable
2. configure terminal
3. license boot level {metroaggrservices | metroipservices | metroservices}
4. end
Licensing the Cisco ASR 900 Series Routers
14
OL-30223-02
Right To Use Licensing
Verifying the RTU Licenses
DETAILED STEPS
Step 1
Command or Action
Purpose
enable
Enables privileged EXEC mode.
• Enter your password if prompted.
Example:
Router> enable
Step 2
configure terminal
Enters global configuration mode.
Example:
Router# configure terminal
Step 3
license boot level {metroaggrservices | metroipservices | Enables the RTU license.
metroservices}
Example:
Router# license boot level move metroipservices
Step 4
Returns to privileged EXEC mode.
end
Example:
Router# end
Verifying the RTU Licenses
• show license right-to-use
Use the show license right-to-use command to view the RTU licenses.
Router# show license right-to-use
Index 1 Feature: metroaggrservices
Period left: Life time
License Type: RightToUse
License State: Active, In Use
License Count: Non-Counted
License Priority: Low
Index 2 Feature: metroipservices
Period left: Life time
License Type: RightToUse
License State: Active, Not in Use, EULA accepted
License Count: Non-Counted
License Priority: Low
Index 3 Feature: metroservices
Period left: Life time
License Type: RightToUse
License State: Active, Not in Use, EULA accepted
License Count: Non-Counted
License Priority: Low
Index 4 Feature: atm
Period left: Life time
License Type: RightToUse
License State: Active, Not in Use, EULA accepted
License Count: Non-Counted
License Priority: Lowe
Licensing the Cisco ASR 900 Series Routers
OL-30223-02
15
Right To Use Licensing
Verifying the RTU Licenses
• show license detail metroaggrservices
Use the show license detail metroaggrservices command for a detailed view of the licenses.
Router# show license detail metroaggrservice
Index: 1
Feature: metroaggrservices
Version: 1.0
License Type: RightToUse
License State: Active, In Use
Lock type: Non Node locked
Vendor info: <UDI><PID>NOTLOCKED</PID><SN>NOTLOCKED</SN></UDI><T>RTU</T>
License Addition: Additive
License Generation version: 0x8200000
License Count: Non-Counted
License Priority: Low
Store Index: 0
Store Name: Built-In License Storage
• show license detail standby
Use the show license detail standby command to view the licenses on the Standby RSP.
Note
If the license accept end user agreement exists, then the EULA agreement is not
displayed.
Router# show license detail standby
Index: 1
Feature: atm
Version: 1.0
License Type: EvalRightToUse
License State: Active, Not in Use, EULA not accepted
Evaluation total period: 8 weeks 4 days
Evaluation period left: 8 weeks 4 days
Period used: 0 minute 0 second
Lock type: Non Node locked
Vendor info: <UDI><PID>NOTLOCKED</PID><SN>NOTLOCKED</SN></UDI><T>RTU</T>
License Addition: Additive
License Generation version: 0x8200000
License Count: Non-Counted
License Priority: None
Store Index: 3
Store Name: Built-In License Storage
Index: 2
Feature: metroaggrservices
Version: 1.0
License Type: EvalRightToUse
License State: Active, In Use
Evaluation total period: 8 weeks 4 days
Evaluation period left: 8 weeks 2 days
Period used: 1 day 18 hours
Transition date: Jun 22 2014 18:28:54
Lock type: Non Node locked
Vendor info: <UDI><PID>NOTLOCKED</PID><SN>NOTLOCKED</SN></UDI><T>RTU</T>
License Addition: Additive
License Generation version: 0x8200000
License Count: Non-Counted
License Priority: Low
Store Index: 0
Store Name: Built-In License Storage
Index: 3
Feature: metroipservices
Version: 1.0
License Type: EvalRightToUse
License State: Active, Not in Use, EULA not accepted
Evaluation total period: 8 weeks 4 days
Evaluation period left: 8 weeks 4 days
Period used: 0 minute 0 second
Lock type: Non Node locked
Licensing the Cisco ASR 900 Series Routers
16
OL-30223-02