Fastening systems
Introduction:
Hiansa has a wide range of solutions for joints and
connections, sheet metal screws, self-threading screws,
concrete screws, sandwich panel screws, threaded screws,
structural screws or wooden structure screws. All of these
can have:
• An electrolytic galvanized coating of 5 to 6 micra.
• Both screw and washer lacquered in any Hiansa color
in combination with the colors of the sheets and panels.
• A nylon head in standard colors.
• Stainless steel AISI-304.
• Delta-Tone coating with exceptional corrosion resistance.
The entire range can be supplied with waterproof washers
manufactured in galvanized steel with a neoprene base.
Self-threading screw for concrete
A perfect anchor for fastening sheet on concrete, brick
and hollow blocks.
The HI-LO double thread with cross-section slots makes
the high thread cut into the masonry while the low thread
stabilizes the anchor. To guarantee proper anchoring, at
least 25 mm of the screw should be in the concrete.
LOW THREAD
FASTENING
HIGH THREAD
FASTENING
Self-drilling screw for beams
Ideal for fastening sheet to a metal structure where drill
depth can reach up to 12 mm. The bit is designed so
that it drills and expels the shavings at the same time.
Characteristics
Material
Hexagonal
head
Nominal
diameter
Length
Drill bit
Max.drill
thickness
Torsion
strength
Shear
strength
Tensile
strength
Manufacturing
standard
8 mm
5.5 mm
28 mm
No. 4
4 mm
10.50 Nm
8.36 KN
12.5 KN
DIN 7504 K
Screw 5.5 x 35 / 115 mm
Cementation
8 mm
steel
5.5 mm
Between 35
and 115 mm
No.5
5 mm
10.5 Nm
8.36 KN
12.5 KN
DIN 7504 K
Screw 5.5 x 28
Cementation
steel
Sandwich panel screw
This screw is especially designed to hold sandwich panels
to a structure. It has two different types of thread; the
thread nearest to the head is for fastening to 0.5-1.0
mm sheet, long spacing between threads, like sheet
metal screws and a second thread with less spacing and
closer thread for thicknesses over 2 mm.
Self-threading screws
These screws are used to join two sheets with pre-drilled
holes. They come in 6.3 mm diameter and lengths
between 19 and 180 mm, with partial thread at 60 mm.
Characteristics
Characteristics
Material
Cementation steel with Ruspert blue
surface coating
Head
Hexagonal 8 mm slotted
Nominal diameter
6,5 mm.
Lengths
Between 32 and 100 mm
Thickness of cement layer
0,15-0,28 mm.
Surface hardness
560-680 HV
Core hardness
32-40 HRC
Material
Cementation steel
Head
Hexagonal 8 mm
Nominal diameter
5.5 mm
Thread length under the head
14 - 15 mm
Manufacturing standard
DIN 7504 K
Bit nº 3
Diameter x Length
5,5 x 60 mm.
Characteristics
Material
Cemented steel
Head
hexagonal 10 mm.
17 Nm
Torsion strength
Shear strength
12,27 KN
Tensile strength
17,2 KN
Manufacturing standard
DIN 6928 FORMAC
PUNTA/1
2 mm
POINT 2
3 mm.
PUNTA/
4 mm
POINT 3
4 mm.
POINT 4 POINT 5
6 mm. 12.5 mm.
Material
Hexagonal
head
Self-drilling 4.8 diameter
Cementation
8 mm
steel
Self-drilling 5.5 diameter
Cementation
8 mm
steel
Self-drilling 6.3 diameter
Cementation
8 mm
steel
Length
min. 13 mm
and max. 50 mm
min. 22 mm
and max. 50 mm
min. 25 mm
and max. 100 mm
Max.drill
thickness
4 mm
5 mm
6 mm
Torsion
strength
7 Nm
10.5 Nm
17 Nm
Shear
strength
6.28 KN
8.36 KN
12.27 KN
Tensile
strength
10 KN
12.5 KN
17.2 KN
Diameter x Length
5,5 x 85 mm.
Panel thickness
30 mm.
Max. drill depth
12 mm.
5,5 x 85 mm.
40 mm.
12 mm.
5,5 x 80 mm.
50 mm.
6 mm.
5,5 x 85 mm.
50 mm.
12 mm.
5,5 x 80 mm.
60 mm.
6 mm.
5,5 x 85 mm.
60 mm.
12 mm.
5,5 x 100 mm.
80 mm.
6 mm.
5,5 x 105 mm.
80 mm.
12 mm.
DRILL BIT – FACADE PANEL INSTALLATION SPECIFICATIONS
Bit nº 5
Panel thickness
Max. drill depth
Diameter x Length
Panel thickness
Max. drill depth
5,5 x 50 mm.
35 mm.
6 mm.
5,5 x 50 mm.
35 mm.
12 mm.
5,5 x 50 mm.
40 mm.
6 mm.
5,5 x 50 mm.
40 mm.
12 mm.
5,5 x 50 mm.
50 mm.
6 mm.
5,5 x 75 mm.
50 mm.
12 mm.
5,5 x 60 mm.
60 mm.
6 mm.
5,5 x 75 mm.
60 mm.
12 mm.
5,5 x 80 mm.
80 mm.
6 mm.
5,5 x 100 mm.
80 mm.
12 mm.
Bit nº 3
Diameter x Length
the mm are the approximate drill capacity thickness
Characteristics
6 mm.
6 mm.
PUNTA/'S
1.2 mm
POINT S
1.2 mm.
Max. drill depth
30 mm.
40 mm.
Diameter x Length
POINT 1
2 mm.
Panel thickness
5,5 x 60 mm.
Bit nº 3
Self-drilling screw
This screw drills, threads and fastens all in the same
movement and saves up to 50% in installation time.
Available in three diameters for thicknesses no greater
than 6 mm with a no.3 drill bit.
DRILL BIT – ROOF PANEL INSTALLATION SPECIFICATIONS
Bit nº 5
DRILL BIT – REFRIGERATOR PANEL INSTALLATION SPECIFICATIONS
Bit nº 3
Panel thickness
Max. drill depth
Diameter x Length
Panel thickness
Max. drill depth
5,5 x 130 mm.
100 mm.
6 mm.
5,5 x 130 mm.
100 mm.
12 mm.
Manufacturing
standard
5,5 x 130 mm.
110 mm.
6 mm.
5,5 x 130 mm.
110 mm.
12 mm.
5,5 x 150 mm.
120 mm.
6 mm.
5,5 x 150 mm.
120 mm.
12 mm.
DIN 7504 K
5,5 x 150 mm.
130 mm.
6 mm.
5,5 x 150 mm.
130 mm.
12 mm.
5,5 x 175 mm.
140 mm.
6 mm.
5,5 x 185 mm.
140 mm.
12 mm.
5,5 x 175 mm.
150 mm.
6 mm.
5,5 x 185 mm.
150 mm.
12 mm.
5,5 x 175 mm.
160 mm.
6 mm.
5,5 x 185 mm.
160 mm.
12 mm.
5,5 x 220 mm.
180 mm.
6 mm.
5,5 x 230 mm.
180 mm.
12 mm.
5,5 x 220 mm.
200 mm.
6 mm.
5,5 x 230 mm.
200 mm.
12 mm.
DIN 7504 K
DIN 7504 K
Fastening systems
Introduction:
Hiansa has a wide range of solutions for joints and
connections, sheet metal screws, self-threading screws,
concrete screws, sandwich panel screws, threaded screws,
structural screws or wooden structure screws. All of these
can have:
• An electrolytic galvanized coating of 5 to 6 micra.
• Both screw and washer lacquered in any Hiansa color
in combination with the colors of the sheets and panels.
• A nylon head in standard colors.
• Stainless steel AISI-304.
• Delta-Tone coating with exceptional corrosion resistance.
The entire range can be supplied with waterproof washers
manufactured in galvanized steel with a neoprene base.
Self-threading screw for concrete
A perfect anchor for fastening sheet on concrete, brick
and hollow blocks.
The HI-LO double thread with cross-section slots makes
the high thread cut into the masonry while the low thread
stabilizes the anchor. To guarantee proper anchoring, at
least 25 mm of the screw should be in the concrete.
LOW THREAD
FASTENING
HIGH THREAD
FASTENING
Self-drilling screw for beams
Ideal for fastening sheet to a metal structure where drill
depth can reach up to 12 mm. The bit is designed so
that it drills and expels the shavings at the same time.
Characteristics
Material
Hexagonal
head
Nominal
diameter
Length
Drill bit
Max.drill
thickness
Torsion
strength
Shear
strength
Tensile
strength
Manufacturing
standard
8 mm
5.5 mm
28 mm
No. 4
4 mm
10.50 Nm
8.36 KN
12.5 KN
DIN 7504 K
Screw 5.5 x 35 / 115 mm
Cementation
8 mm
steel
5.5 mm
Between 35
and 115 mm
No.5
5 mm
10.5 Nm
8.36 KN
12.5 KN
DIN 7504 K
Screw 5.5 x 28
Cementation
steel
Sandwich panel screw
This screw is especially designed to hold sandwich panels
to a structure. It has two different types of thread; the
thread nearest to the head is for fastening to 0.5-1.0
mm sheet, long spacing between threads, like sheet
metal screws and a second thread with less spacing and
closer thread for thicknesses over 2 mm.
Self-threading screws
These screws are used to join two sheets with pre-drilled
holes. They come in 6.3 mm diameter and lengths
between 19 and 180 mm, with partial thread at 60 mm.
Characteristics
Characteristics
Material
Cementation steel with Ruspert blue
surface coating
Head
Hexagonal 8 mm slotted
Nominal diameter
6,5 mm.
Lengths
Between 32 and 100 mm
Thickness of cement layer
0,15-0,28 mm.
Surface hardness
560-680 HV
Core hardness
32-40 HRC
Material
Cementation steel
Head
Hexagonal 8 mm
Nominal diameter
5.5 mm
Thread length under the head
14 - 15 mm
Manufacturing standard
DIN 7504 K
Bit nº 3
Diameter x Length
5,5 x 60 mm.
Characteristics
Material
Cemented steel
Head
hexagonal 10 mm.
17 Nm
Torsion strength
Shear strength
12,27 KN
Tensile strength
17,2 KN
Manufacturing standard
DIN 6928 FORMAC
PUNTA/1
2 mm
POINT 2
3 mm.
PUNTA/
4 mm
POINT 3
4 mm.
POINT 4 POINT 5
6 mm. 12.5 mm.
Material
Hexagonal
head
Self-drilling 4.8 diameter
Cementation
8 mm
steel
Self-drilling 5.5 diameter
Cementation
8 mm
steel
Self-drilling 6.3 diameter
Cementation
8 mm
steel
Length
min. 13 mm
and max. 50 mm
min. 22 mm
and max. 50 mm
min. 25 mm
and max. 100 mm
Max.drill
thickness
4 mm
5 mm
6 mm
Torsion
strength
7 Nm
10.5 Nm
17 Nm
Shear
strength
6.28 KN
8.36 KN
12.27 KN
Tensile
strength
10 KN
12.5 KN
17.2 KN
Diameter x Length
5,5 x 85 mm.
Panel thickness
30 mm.
Max. drill depth
12 mm.
5,5 x 85 mm.
40 mm.
12 mm.
5,5 x 80 mm.
50 mm.
6 mm.
5,5 x 85 mm.
50 mm.
12 mm.
5,5 x 80 mm.
60 mm.
6 mm.
5,5 x 85 mm.
60 mm.
12 mm.
5,5 x 100 mm.
80 mm.
6 mm.
5,5 x 105 mm.
80 mm.
12 mm.
DRILL BIT – FACADE PANEL INSTALLATION SPECIFICATIONS
Bit nº 5
Panel thickness
Max. drill depth
Diameter x Length
Panel thickness
Max. drill depth
5,5 x 50 mm.
35 mm.
6 mm.
5,5 x 50 mm.
35 mm.
12 mm.
5,5 x 50 mm.
40 mm.
6 mm.
5,5 x 50 mm.
40 mm.
12 mm.
5,5 x 50 mm.
50 mm.
6 mm.
5,5 x 75 mm.
50 mm.
12 mm.
5,5 x 60 mm.
60 mm.
6 mm.
5,5 x 75 mm.
60 mm.
12 mm.
5,5 x 80 mm.
80 mm.
6 mm.
5,5 x 100 mm.
80 mm.
12 mm.
Bit nº 3
Diameter x Length
the mm are the approximate drill capacity thickness
Characteristics
6 mm.
6 mm.
PUNTA/'S
1.2 mm
POINT S
1.2 mm.
Max. drill depth
30 mm.
40 mm.
Diameter x Length
POINT 1
2 mm.
Panel thickness
5,5 x 60 mm.
Bit nº 3
Self-drilling screw
This screw drills, threads and fastens all in the same
movement and saves up to 50% in installation time.
Available in three diameters for thicknesses no greater
than 6 mm with a no.3 drill bit.
DRILL BIT – ROOF PANEL INSTALLATION SPECIFICATIONS
Bit nº 5
DRILL BIT – REFRIGERATOR PANEL INSTALLATION SPECIFICATIONS
Bit nº 3
Panel thickness
Max. drill depth
Diameter x Length
Panel thickness
Max. drill depth
5,5 x 130 mm.
100 mm.
6 mm.
5,5 x 130 mm.
100 mm.
12 mm.
Manufacturing
standard
5,5 x 130 mm.
110 mm.
6 mm.
5,5 x 130 mm.
110 mm.
12 mm.
5,5 x 150 mm.
120 mm.
6 mm.
5,5 x 150 mm.
120 mm.
12 mm.
DIN 7504 K
5,5 x 150 mm.
130 mm.
6 mm.
5,5 x 150 mm.
130 mm.
12 mm.
5,5 x 175 mm.
140 mm.
6 mm.
5,5 x 185 mm.
140 mm.
12 mm.
5,5 x 175 mm.
150 mm.
6 mm.
5,5 x 185 mm.
150 mm.
12 mm.
5,5 x 175 mm.
160 mm.
6 mm.
5,5 x 185 mm.
160 mm.
12 mm.
5,5 x 220 mm.
180 mm.
6 mm.
5,5 x 230 mm.
180 mm.
12 mm.
5,5 x 220 mm.
200 mm.
6 mm.
5,5 x 230 mm.
200 mm.
12 mm.
DIN 7504 K
DIN 7504 K