Job:
Type:
Notes:
Form 10 Round LED
CP / MP Post Top Mount
Page 1 of 3
The Philips Gardco post top mounted Round Form 10 LED products are cutoff luminaires featuring LED arrays.
Round Form 10 LED luminaires provide performance excellence and advanced Philips Gardco LED thermal
management technology. High performance Class 1 LED systems offer the potential for energy savings up to
50% when compared to HID systems. Housings are one-piece seamless spun aluminum and finished with either
Architectural Class 1 anodizing , with hardcoat, fade resistant, electrostatically applied TGIC polyester powdercoat
or polyurethane. Optional twin glow rings at post tops are available in (4) colors and are illuminated by the primary
source. Luminaires provide full cutoff performance.
PREFIX
MOUNTING
DISTRIBUTION
LED WATTAGE
LED SELECTION
CP
VOLTAGE
MP
FINISH
OPTIONS
Enter the order code into the appropriate box above. Note: Philips Gardco reserves the right to refuse a configuration. Not all combinations and configurations are valid.
Refer to notes below for exclusions and limitations. For questions or concerns, please consult the factory.
PREFIX
Available in 70LA and 85LA LED Wattages Only
CP17L
CP17L-DIM
MP17L
MP17L-DIM
Available in 110LA and 160LA LED Wattages Only
CP22L
CP22L-DIM
MP22L
MP22L-DIM
17" Cylindrical Luminaire LED - Constant Wattage
17" Cylindrical Luminaire LED - 0-10V Dimming
17" Semi-Spherical Luminaire LED - Constant Wattage
17" Semi-Spherical Luminaire LED - 0-10V Dimming
22" Cylindrical Luminaire LED - Constant Wattage
22" Cylindrical Luminaire LED - 0-10V Dimming
22" Semi-Spherical Luminaire LED - Constant Wattage
22" Semi-Spherical Luminaire LED - 0-10V Dimming
Retrofit Kits for existing Form 10 Round 17" and 22" HID luminaires are available. See Legacy LED Retrofit Kits Submittal Data Sheet (G200-21) for Retrofit Kit information.
MOUNTING
See
Mounting
Illustrations
on Page 2 for
more
information.
POLES
TENONS
SRS3
MIN O.D. 2.88"
MAX O.D.
3.00"
RA4/SRS4
CP / MP 17
CP / MP 22
MIN O.D. 3.58"
MIN O.D. 3.50"
MAX O.D.
MAX O.D.
3.85"
4.00"
RA5/SRS5
MIN I.D. 4.62"
MAX O.D.
4.85"
T2
2 3/8" O.D.
X 4"
T3
2 7/8" O.D.
X 4"
T3
3" O.D.
X 4"
T4
4" O.D.
X 6"
MP17
P11 (ill. 2)
P12 (ill. 1)
Not Available
T14 (ill. 3)
T15 (ill. 3)
T16 (ill. 3)
CP17
P21 (ill. 2)
P22 (ill. 1)
Not Available
T24 (ill. 4)
T25 (ill. 3)
T26 (ill. 3)
MP22
CP22
P31 (ill. 5)
P32 (ill. 2)
P33 (ill. 1)
T34 (ill. 4)
T35 (ill. 4)
T36 (ill. 4)
Not Available
Not Available
T37 (ill. 3)
P41 (ill. 5)
P42 (ill. 2)
P43 (ill. 1)
T44 (ill. 4)
T45 (ill. 4)
T46 (ill.4)
T47 (ill. 3)
distribution
2
Type II
4
Type IV
3
Type III
5
Type V
Type II, Type III and Type IV optics are field rotatable.
Type V optics feature unitized lens.
LED wattage AND LUMEN VALUES
Average
System
Watts1
LED
Current
(mA)
LED
Selection
Type 2
Type 3
Type 4
Type 5
70LA
70
350
NW
7,240
7,467
7,303
7,162
85LA
85
350
NW
8,900
9,318
9,045
8,921
110LA
110
350
NW
10,928
11,053
11,050
10,755
160LA
160
530
NW
15,252
15,659
15,109
15,422
Ordering
Code
Luminaire Initial Absolute Lumens2,3
© 2014 Koninklijke Philips N.V. All rights reserved.
G200-025 10/14 page 1 of 3 www.philips.com/luminaires
Basis of Lumen Data : Photometric tests performed in compliance
with IESNA LM-79, except where otherwise indicated.
Notes:
1. Wattage may vary by +/- 8% due to LED manufacturer forward volt
specification and ambient temperature. Wattage shown is average for
120V through 277V input. Actual wattage may vary by an additional
+/- 10% due to actual input voltage.
2. Values shown are for luminaires without the HS external shield
option. Tests are in process for luminaires with the HS option and WW
luminaires. Contact [email protected] if approximate
estimates are required for design purposes.
3. LED arrays feature LEDs that provide from 100 to 130 lumens per
watt when operated at 350 mA. Lumen values based on tests performed
in compliance with IESNA LM-79.
Form 10 Round LED
CP / MP Post Top Mount
Page 2 of 3
led selection
voltage
CW
Cool White - 5700°K - 75 CRI
NW
Neutral White - 4000°K - 70 CRI
WW
Warm White - 3000°K - 80 CRI
FINISH
120
208
240
277
347
480
OPTIONS
BRP
BLP
WP
NP
BRA
BLA
NA
OC
Bronze Paint
Black Paint
White Paint
Natural Aluminum Paint
Bronze Anodized
Black Anodized
Natural Anodized
Optional Color Paint
F4
LF
PC5,6
PCR5
Specify Optional Color or
RAL ex: OC-LGP or OC-RAL7024.
SC
Special Paint
Specify. Must supply color chip.
Glow Rings
GRCClear
GRYYellow
GRGGreen
GRRRed
UNIV
HVU
120V through 277V, 50hz or 60hz
347V through 480V,
50hz or 60hz (High Voltage Universal)
Fusing
In-Line/In-Pole Fusing
Photocontrol and Receptacle
Photocontrol Receptacle only
4. In Head. Provide Specific input voltage.
5. Available in CA Style only. Not available in MA Style.
6. Not available in 480V. Provide Specific input voltage.
DIMENSIONS AND EPA
MOUNTING illustrations
A
A
Illustration 1
B
Yoke fitter
slides into
pole
B
D
pole top
tenon
Yoke fitter
slides over
pole
Illustration 4
C
Illustration 3
pole
Preferred
Attachment
Method
D
Illustration 2
Yoke fitter
slides over
tenon
Illustration 5
tenon fitter adaptor
pole
Yoke fitter
slides over
tenon
Size
17"
CP Style
B
A
17"
8"
C
D
EPA’s
Single
Weight
Single
MP Style
B
Size A
10"
18"
.7 ft2
31 lbs
17"
43.18 cm 20.32 cm 25.40 cm 45.32 cm .07 m
2
22"
22"
11"
11"
22"
14.06 kg
50 lbs
1.02
55.88 cm 27.94 cm 27.94 cm 55.88 cm .09 m
2
22.68 kg
© 2014 Koninklijke Philips N.V. All rights reserved.
G200-025 10/14 page 2 of 3 www.philips.com/luminaires
17"
11"
C
D
EPA’s
Single
10"
21"
.7 ft2
43.18 cm 27.94 cm 25.40 cm 53.34 cm .07 m2
22"
22"
14"
11"
25"
1.02
55.88 cm 35.56 cm 27.94 cm 63.50 cm .09 m2
Weight
Single
31 lbs
14.06 kg
50 lbs
22.68 kg
Yoke fitter
slides over
tenon
Refer to Table on Page 1 for
mounting ordering information.
Form 10 Round LED
CP / MP Post Top Mount
Page 3 of 3
LUMINAIRE CONFIGURATION INFORMATION
constant wattage configurations: Standard LED
luminaires provide constant wattage and constant light output when power to
the luminaire is energized.
dimming "-DIM" configurations: Dimmable LED luminaires are
provided with 0 - 10V dimming for connection to a control system provided
by others.
SPECIFICATIONS
GENERAL: The Philips Gardco post top mounted Form 10 Round LED
products are cutoff luminaires featuring LED arrays. Form 10 Round LED
luminaires provide performance excellence and advanced Philips Gardco
LED thermal management technology. High performance Class 1 LED
systems offer the potential for energy savings up to 50% when compared to
HID systems. Housings are one-piece seamless spun aluminum and finished
with either Architectural Class 1 anodizing , with hardcoat, fade resistant,
electrostatically applied TGIC polyester powdercoat or polyurethane. Optional
twin glow rings at post tops are available in (4) colors and are illuminated by
the primary source. Luminaires provide full cutoff performance.
HOUSING: Housing is one piece, .100" (.25cm) seamless aluminum with
integral rolled circumferential reveal and lower section aperture incorporating
a returned flange stiffener to protect against housing edge deformation.
YOKE: The 9/16" (1.42cm) diameter parallel yokes of high strength, low
mass schedule 40 steel are precision contoured to match the CP or MP
housing silhouette. Welds or fasteners are not visible at the luminaire or
pole attachment. The yoke is electrogalvanized and coated with satin black
polyurethane or polyester powder coat.
LENS: One piece, diecast aluminum door frame retains the optically clear,
heat and impact resistant tempered flat glass, in a sealed manner using
hollow section, high compliance, memory retentive extruded silicone rubber.
Concealed stainless steel hinge and two (2) fasteners secure lens assembly to
luminaire.
THERMAL MANAGEMENT: The Philips Gardco Form 10 Round LED
luminaires utilize extruded aluminum integral thermal radiation fins to provide
the excellent thermal management so critical to long LED system life.
LED RELIABILITY:
PREDICTED LUMEN DEPRECIATION DATA
Ambient Temperature
°C
25 °C
40 °C
Driver mA
L70 Hours8
350 mA
150,000
530 mA
100,000
350 mA
100,000
530 mA
70,000
8. Predicted performance derived from LED manufacturer’s data and engineering design
estimates,
based on IESNA LM-80 methodology. Actual experience may vary due to field application
conditions. L70 is the predicted time when LED performance depreciates to 70% of initial lumen
output.
OPTICAL SYSTEMS: Philips Gardco Form 10 Round LED luminaires
utilize lensed LED arrays set to achieve IES Type II, Type III, Type IV and Type V
distributions. Individual LED arrays are replaceable. Optical systems are field
rotatable. Luminaires feature high performance Class 1 LED systems.
ELECTRICAL: Luminaires include a complete prewired LED driver assembly,
provided as part of the optical assembly. Luminaires include an LED driver
that accepts 120V through 277V, or 347V through 480V, 50hz to 60hz,
input. Driver output is based on the LED wattage selected. Component-tocomponent wiring within the luminaire will carry no more than 80% of rated
current and is listed by UL for use at 600 VAC at 302°F / 150°C or higher. Plug
disconnects are listed by UL for use at 600 VAC, 15A or higher. Power factor
is not less than 90%. Luminaires consume 0.0 watts in the off state. Surge
protector standard. 10KA per ANSI/IEEE C62.41.2.
FINISH: Anodized housings are created with an Aluminum Association
Architectural Class I anodizing process to achieve a bronze, black or natural
aluminum finish. Painted units are finished with hardcoat, fade resistant,
electrostatically applied TGIC polyester powdercoat or polyurethane.
LABELS: All luminaires bear UL or CUL (where applicable) Wet Location
labels.
WARRANTY: Philips Gardco Form 10 Round LED luminaires feature a 5
year limited warranty, including a 5 year limited warranty covering LED arrays
and LED drivers. See Warranty Information on www.sitelighting.com for
complete details and exclusions.
FULL Cutoff performance: Full cutoff performance means a luminaire distribution where zero candela intensity occurs at an angle at or above 90° above nadir .
Additionally, the candela per 1000 lamp lumens does not numerically exceed 100 (10 percent) at a vertical angle of 80° above nadir. This applies to all lateral angles around the
luminaire.
Cutoff performance: Cutoff performance means a luminaire distribution where the candela per 1000 lamp lumens does not numerically exceed 25 (2.5 percent) at an
angle at or above 90° above nadir, and 100 (10 percent) at a vertical angle of 80° above nadir. This applies to all lateral angles around the luminaire.
© 2014 Koninklijke Philips N.V. All rights reserved.
Philips reserves the right to make changes in specifications
and/or to discontinue any product at any time without notice
or obligation and will not be liable for any consequences
resulting from the use of this publication.
G200-025 10/14 page 3 of 3 www.philips.com/luminaires
Philips Lighting
North America Corporation
200 Franklin Square Drive
Somerset, NJ 08873
Tel. 855-486-2216
Imported by: Philips Lighting,
A division of Philips Electronics Ltd.
281 Hillmount Rd,
Markham, ON, Canada L6C 2S3
Tel. 800-668-9008