Intructions For Instructions
Use
For Use
OrankaAroma
Aroma
Safe
Dispenser
Oranka
Safe
Dispenser
Dispenser Set Up
1. Base Unit Assembly
a) Position the dispenser base unit in the desired position. Ideally
have a minimum of 6 inches workspace around the dispenser if
possible, which will allow the dispenser cooling fan to work at
it’s optimum.
b) Place 2 x damp cooling rings (4) on to the dispenser cooling
plate (18).
c) Attach the drip tray (19)at the bottom of the base by inserting the
protruding foot in to the space provided.
2. Juice Tank Assembly
a) Secure the tap housing (6) on to the tank by twisting the housing
on to the tank.
b) Push the tap handle ( 11) back as far as possible
c) With clean or gloved hands insert the tap hose (7). The tap hose
should have it’s ‘eye’ facing the front of the tank.
d) Push the tap hose (7) flush into position in the tank. The final
position of the tap hose tube should be in between the spring
actioned tap handle (11) and the tap housing (6).
e) Place the magnetic spinner ( 8) on to the spindle with it’s white
collar and grooved side facing upwards.
3. Fitting & Filling The Juice Tank
a) Adjust the tank fixing clips (3) so that they are positioned away
from the base unit ( facing outwards).
b) Place the juice tank (5) on to the top of the dispenser base unit.
The metal base plate of the tank should sit on top of the metal
cooling plate of the dispenser, with the 2 x damp cooling rings in
between.
c) With the tank in position, move the tank fixing clips ( 3) towards
the tank so that they secure the tank in to place / slide clips over
metal holding backet.
d) Cover the magnetic spinner (8) with approx. 3 litres of fresh cold
water
e) Switch the dispenser on (1)
f) Adjust the thermostat (2) to the 2 o’clock position. ( 9 o’clock =
minimum temp / 3 o’clock = maximum , coldest temp)
g) Empty the Oranka juice concentrate carton in to the tank and
top up with water to either the 5 or 10 litre line on the tank ( see
concentrate and fill levels below)
4. Concentrate and Fill Levels
I 1 x 0.5 litre carton of Oranka 1+19 = 10 litres of final product
II 1 x 0.5 litre carton of Oranka 1+9 = 5 litres of final product
III 1 x 1 litre carton of Oranka 1+9 =10 litres of final product
IV 1 x 1 litre carton of Oranka 1+4 = 5 litres of final product
V2 x 1 litre cartons of Oranka 1+4 = 10 litres of final product
first fill level red line (middle of the tank) = 5 litres / second fill
level red line ( top of tank) = 10 litres.
5. Closing and Locking The Juice Tank
a) Place the aroma cap (9) on top of the juice ( it will float!)
b) Lift the metal valve in the centre of the aroma cap (9) so that the
air in the pocket underneath disperses.
c) Fill the channel (12) with one cup of water (using the small cup
provided)
d) Hold the lid (10) by the locking devices (14), ensuring the locking
devices are extended to the open position.
e) There is a magnetic bolt in each locking device. When the bolt is
sitting upright the lock is open. When the bolt is dropped down
in to the device the lock is closed. The bolts can be opened by
holding one of the magnets provided (17) over the top of the bolt.
f) Place the lid on top of the tank.
g) To lock the lid on to the tank, hold the inside of the of the lid’s
edge on the left and the right of the locking device with your
index and middle finger. Now you can exert light pressure upon
the locking device with your thumb to close the lock. The metal
pins will fall in to the holes.
6. Optional Extra Steps
a) A magnetic dating label is provided to affix to the side of the
base unit. Use a dry wipe pen to detail the product , date of
preparation and use by date.
b) Juice dispensing can be locked off by using a tap lock (15). This
slides over the tap handle and tap housing. Close the red locking
device (16) by pushing it in.
c) To unlock, hold a magnet against the stand off atop the locking
device and slide out the red locking device (16). Slide the tap lock
(15) down and off the tap handle and tap housing.
Legend
 On / Off Switch
 Thermostat
 Fixing Clips
 Cooling Rings
 Juice Tank
 Tap House
 Tap Hose
 Magnetic Float
 Aroma cap
 Juice Tank Lid
 Tap Handle
 Channel / Gully
 Locking Devices
 Tap Lock
 Locking Device - Tap Lock
 Magnetic Key
 Cooling Plate
 Drip Tray
If you have any questions / comments, please contact us: T +44(0)870 - 830 1555 - E [email protected]
Intructions For Instructions
Use
For Use
OrankaAroma
Aroma
Safe
Dispenser
Oranka
Safe
Dispenser
Technical data
Juice Tank Capacity: 10 Litres (to top red mark)
Dimensions of Machine: Width = 30 cms Depth = 34.5 cms Height = 63 cms
Power Supply: 220/240 V - 50 Hz - 45 W
Power Consumption:
0.17 kW
Machine Weight (Empty): 15.8 kgs
30 cm
63 cm
Emptying /Cleaning The Dispenser
1. Base Unit Assembly
1. Base Unit
a) Turn the dispenser off (1)
b) Undo the fixing clips (3) that secure the tank to the base unit.
2. Emptying The Juice Tank
a) Unlock the tank lid locking device (14) on both sides of the tank
using the magnet provided (17)
b) To unlock the lid on to the tank, hold the inside of the of the lid’s
edge on the left and the right of the locking device with your
index and middle finger. Now you can hold the magnet provided
(17) over the top of the bolt so that it sits upright. Pull the red
lock outwards to release.
c) Remove the tank lid (10)
d) Lift and remove the aroma cap ( 9) from the inside of the tank.
e) Lift the tank up from the base unit and empty any remaining
contents (note that there may be some water remaining in the
channel / gulley (12)).
(CAUTION: if the juice tank is frozen to the base unit DO NOT
REMOVE IT BY FORCE. Simply pour a little tepid water in to the tank
and leave for a few minutes, then the tank can easily be removed)
f) When the tank is empty press the tap handle (11) back as far as
possible and pull out the tap hose (7)
g) Twist and pull the tap housing (6) off of the tank.
3. Cleaning The Tank and Parts
a) The following parts should now be ready for cleaning:
(4) – cooling rings (5) – juice tank (6) – tap housing (7) – tap hose
(8) – magnetic spinner (9) – aroma cap (10) – tank lid
b) The cooling rings (4) should be rinsed in tepid water and put to
one side
c) The inside of the tap hose ( 7) should be cleaned with a small
brush ( supplied by Oranka) and placed in a cup with sanitiser.
d) All of the parts in the above section a) should be placed in the
dishwasher at a temperature of at least 60 degrees Celcius.
Please see Oranka Hygiene Instructions for further guidance
regarding cleaning. It is recommended that tap hoses and cooling
rings are changed every month.
34.5 cm
23.5 cm
NB! - Keep at least 15 cms (6")
of free space around
the machine at all times.
Legend
 On / Off Switch
 Thermostat
 Fixing Clips
 Cooling Rings
 Juice Tank
 Tap House
 Tap Hose
 Magnetic Float
 Aroma cap
 Juice Tank Lid
 Tap Handle
 Channel / Gully
 Locking Devices
 Tap Lock
 Locking Device - Tap Lock
 Magnetic Key
 Cooling Plate
 Drip Tray
If you have any questions / comments, please contact us: T +44(0)870 - 830 1555 - E [email protected]