Avery Dennison​Ⓡ
TrafficJet™ PF Adjustment
Instructional Bulletin #1.02
June 2016
Perform PF Adjustment
1.
2.
​
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
Load the media.
Select the ​correct User Type​ on the printer display. If the User Type is not yet set or available,
please follow the instructions how to set up a new User Type​.
The machine will scan the available width and position of the media.
On the machine click Menu > Menu > Right Arrow button > Enter.
Click the Up or Down arrow to select the correct User Type again and click Enter.
Click Down Arrow two times until you see 7>3: PF Adjust>
Click Right Arrow and you will see PF1: Initial Print
Click Enter and you will see FeedLength: 250mm
Use the​ Up or Down Arrow button until you have a FeedLength value of 500mm and click Enter.
The machine warm up and print 2 thin lines on the right side of the media approximately 500mm
apart. Do not skip the warm up process!
Measure the EXACT distance between the 2 lines with a tolerance of 0.1mm
On the machine click Menu > Right Arrow button > Enter.
Click the Up or Down Arrow to select the correct User Type again and click Enter.
Click Down Arrow two times until you see 7>3: PF Adjust>
Click Right Arrow and you will see PF1: Initial Print
Click Down Arrow until you see PF2: Initial Change and click Enter
You will now see Init.: 500.0/500mm in your display
Use the U or Down Arrow button, until the left value matches exactly the value you have measured
between the 2 lines and click Enter to confirm.
Click the Down Arrow one time until you see PF3: Confirm Print and click Enter
The display should now show FeedLength: 500mm. If not use
​ the Up or Down Arrow​ button until
the value shows 500mm and click Enter
The machine will again warm up and print 2 thin lines on the right side of the media approximately
500mm apart. Do not skip the warm up process!
Measure the EXACT distance between the 2 lines with a tolerance of 0.1mm and it should be
exactly 500mm.
a. If your print is still smaller than 500mm (for example 0.2mm smaller) ​subtract​ 0.2mm
from the corrected value entered before.
b. If your print is now longer than 500mm (for example 0.3mm longer) ​add​ 0.3mm to the
corrected value entered before.
c. Verify the Confirmation Print until the gap between the lines is accurate within 0.1mm
from 500mm length.
Once satisfied, in the 7>3: PF Adjust menu click the Up or Down Arrow button until you see PF4:
Micro Print and click Enter. Do not skip the warm up process!
Once the machine finishes printing, open the cover and look for the pattern that has NO white line
or a dark line visible between the upper and lower part of the pattern.
Take the corresponding value and enter this in the machine display, using the Up or Down Arrow
button.
Confirm with Enter and click Menu to go back to the main menu as you have now performed the
PF Adjustment.
Verify the PF Adjustment is Satisfactory
Open FlexiSign & Print
●
●
In FlexiSign & Print, create a TrafficJet Spot6 Black square of 500 x 500mm.
Click File > RIP and Print
Instructional Bulletin #1.00
TrafficJet™ PF Adjustment
Page 1 of 2
reflectives.averydennison.com
Open Production Manager
●
●
●
●
●
Double click the file in the Hold queue
Pick the correct Preset and verify if the size is still 500 x 500mm in the settings.
Click the Send button
The printer will now start printing the 500 x 500mm TrafficJet Spot6 Black square. Do not skip the
warm up process!
Once finished, measure the length of the square and this should be exactly 500mm.
If the length of this square in not 500mm, please make the proper corrections until it is.
TIP!
●
●
●
Always perform the PF Adjustment over a length of 500mm as this is most accurate.
Record the exact values per User Type as there are cases where the printer loses the corrected
values.
After doing one or more PF Adjustments, Power Off the machine and unplug the main cable.
Press the Power Button several times until the machine is fully discharged to force the machine to
save the PF values in it’s memory.
The above Avery Dennison literature provides information to the user for proper application, storage and other requirements. Please refer to Product Data
Bulletins or your local Avery Dennison Representative for warranty information. Find the latest information on the Avery Dennison website,
www.reflectives.averydennison.com​. We encourage you to check our website periodically for updates.
All statements, technical Information and recommendations about Avery Dennison products are based upon tests and information believed to be reliable, but do
not constitute a guarantee or warranty of any kind. All Avery Dennison products are sold with the understanding that Purchaser has independently determined
the suitability of such products for its intended and other purposes.
For technical questions, please contact ​[email protected]
Instructional Bulletin #1.00
TrafficJet™ PF Adjustment
Page 2 of 2
reflectives.averydennison.com