c::::::::=:=:::==============================-::::::--I
REFLECT LIGHT®
CHARACTERISTICS
RETRO-REFLECTIVE MARKING SPRAY
STORAGEANDHANDUNG
ADVICE ON USE
• Apply to a clean, dry surface.
• Apply
thin,
even
coats
10 to 20
REFLECTLlGHT®is a retro-reflective varnish aerosolwhich becomesluminous in darknessin
The aerosols should be stored between
a beam of light (torch, vehicle headlights, etc)
15 and 25°C and 50% to 60% relative
em from the surface (application by .
• It is formulated with specially-treatedglassmicrobeads.
humidity.
successive tints)
A «safety» solution for easysignalling of a natural obstacle or particular risk in poor visibility,
outside or inside.
than 50°C.
Numerous applicationsfor an effect similar to signage panels signalling a hazardousarea,
Keep away from all ignition
marking out a route, securing premises,sites, signagefor sports events.
sources and direct sunlight.
Do not expose to a temperature greater
and heat
As with any other handling and storage
operation, it is especially recommended
Long lasting
over
• Applicable in one thin coat on all surfaces and materials.
specific mix of several types
of specially-treated
• Good adhesion.
• Quick drying 5 min.
glass rnicrobeads.
overload
achieve
normally required (except on porous
surfaces).
• Upside down.
(concrete,
wood,
bitumen,
(toluene, xylene, etc.)
Night
or
with
our
15).
• This product can «illuminate» at night
under
a direct
light
beam
(similar effect to signalling panels).
se-
clearly, to mix the paint properly (in
particular to mix the glass micro-
• Shake the aerosol
material
regularly du-
fairly heavy, they fall to the bottom
of the aerosol quickly). Shake the
approximately
HEALTH AND SAFETY
the
aerosol
aerosol again every thirty seconds
the dry painted surface.
Consult
the
for about fifteen
ring use (as the microbeads are
to prevent projections (mist).
shining a torch held at eye level onto
application
vigorously
beads in again).
compatibility.
equipment (handle, stencils, see page
objects
surfaces to check
• The retro-reflection can be checked by
APPUCATION METHOD
• Manually
in advance on
• Protect adjacent surfaces if necessary
gas: specific mix of isobu-
• BEFORE USE: shake
conds, even after hearing the beads
plastic or painted
complex mix free of chlorina-
metal,
stone, etc.).
Solvents:
Propellant
the
maximum
reflective power. A single thin coat is
A test is recommended
tane and propane.
Day
to
free of lead and cadmium.
ted solvents and aromatic compounds
• Immediately highly reflective at night in a direct light beam (30 to 40 ml.
to
. • Can be applied to all types of surface
Binder: acrylic.
Pigments:
not
be barely visible.
COMPOSITION
time: six to twelve months (depending on the surfaces and
application conditions)
care
applications
• During the day, the application should
NOT TO SMOKE.
PROPERTIES
• Take
safety
application
and vent regularly.
data
sheets free of charge on the Internet:
www.quick-fds.com.
during
• DO NOT APPLY A SINGLE THICK
COAT.
• AFTER USE: purge
upright
(until
only gas is released) to clean valve
Day
Night
and spray.
• Should «haphazard»
spraying oc-
cur (microbeads blocking the
valve
in the open position), vent the aerosol for a long time and shake it
well again before
using it once
more; if the defect continues, remove the sprayer.
• If the aerosol clogs, shake it and
press the
PACKAGING
Aerosol cans, volume 650 ml I 500 ml net, in boxes of 6.
sprayer several times
in succession to obtain a regular
·:::
I
spray.
....
\..9
Z
~
0:::::
«
~
w
Z
::;