JAC GRAPHICS DIGILABEL
Product Range Paper
JAC GRAPHICS DIGILABEL
Product Range Films
Description of JAC Digilabel Products for Indigo Sheets
Description of JAC Digilabel Products for Indigo Sheets
These products have been specially developed for the use on HP Indigo Digital Printing Systems and are all equipped with safety edges.
The face stock guarantees good toner adhesion even without pre-treatment. Due to the stability of the laminate the products are
characterized by smooth runability as well as excellent flatness. All products are also printable in conventional offset. Make sure the
surface is clean, dry and free of oil or grease before before applying the label.
These products have been specially developed for the use on HP Indigo Digital Printing Systems and are all equipped with safety edges.
The face material guarantees good toner adhesion. A 100 % ink transfer from the blanket to paper significantly reduces cleaning
requirements. The excellent ink bonding avoids damage when scratching. The superb flatness ensures good runnability, smooth
passing through the machine and clean kiss-cutting. Make sure the surface is clean, dry and free of oil or grease before applying
the label.
FACE MATERIAL
DIGILABEL
DIGILABEL
DIGILABEL
DIGILABEL
MATT
SEMI-GLOSS
GLOSS
HIGH GLOSS
FACE MATERIAL
DIGILABEL MATT
top-quality, machine coated,
wood free paper, white, matt
DIGILABEL SEMI-GLOSS
top-quality, machine coated,
wood free paper, white, semi-gloss
DIGILABEL GLOSS
top-quality, machine coated,
wood free paper, white, gloss
DIGILABEL HIGH GLOSS
top-quality, cast coated, wood free
paper, white with mirror finish
ADHESIVE
DURO D2000
is a dispersion-based permanent acrylic
adhesive displaying very good processing
properties and excellent guillotining
behaviour. Its good adhesion permits use
on a diversity of surfaces, such as paper,
steel, glass etc. It also displays very good
UV stability. It is BfR-approved for direct
contact with dry, non-fatty and nonalcoholic foodstuffs. It also satisfies the
criteria of the so-called "toy standard"
EN71-3.
ADHESIVE
SILICONE PAPER
D2000
D2000
D2000
D2000
B110D
B110D
B110D
B110D
SPLIT
MEASUREMENT/BOX CONTENT
x
x
x
x
32
32
32
32
x
x
x
x
46
46
46
46
cm/250
cm/250
cm/250
cm/250
per
per
per
per
box
box
box
box
AVERAGE VALUES
MATT
SEMI-GLOSS GLOSS HIGH GLOSS
Weight (g/m2)
Weight Total Laminate (g/m2)
Thickness (µm)
Thickness Total Laminate (µm)
Tensile Strength
ISO 1924/2 (kN/m MD)
PPS roughness (µm)
Opacity (%)
Shelf life of laminate* (years)
90
200
85
200
80
190
70
170
90
200
70
180
83
195
90
200
6.2
2.3
92
2
4.0
1.2
87
2
6.0
1.2
88
2
4.5
0.7
89
2
DIGILABEL
DIGILABEL
DIGILABEL
DIGILABEL
PE WHITE MATT
PP CLEAR GLOSS
PP WHITE GLOSS
PET CLEAR GLOSS
FACE MATERIAL
DIGILABEL PE WHITE MATT
single layer PE-Foil, white, matt
DIGILABEL PP CLEAR GLOSS
PP-Foil, transparent, glossy
DIGILABEL PP WHITE GLOSS
PP-Foil, white, glossy
DIGILABEL PET CLEAR GLOSS
PET-Foil, transparent, glossy
* Refers to adhesion and printability when stored in original packaging in dark, dry conditions at a temperature
of 22 °C ± 2 °C and a rfelative huidity of 50 % ± 5 %.
Average Values (measured on glass)
Adhesion (FTM1) after 24h (N/25mm)
Initial adhesion/tack (FTM9)
Shear Strength (FTM8)
Recommended minimum
application termperature (°C)
Heat resistance
up to 24h (°C)
up to 1h (°C)
Resistance to cold* (°C)
Ageing stability**
11
19
2
2
+ 100
+ 160
- 20
very good
DURO AL180
is a crystal clear, acrylic-based adhesive
with max. UV- and weather resistance.
Good initial and final adhesion.
Resistant against high temperatures.
NONPERM C4
is a removable, transparent acrylic adhesive
with high UV- and weather resistance.
Good initial and final adhesion. Resistant
against high temperatures. When applied to
surfaces it reacts with, the label may lose
its removability. This includes surfaces with
nitrocellulose paints, polystyrene, (fresh)
screen printing inks and certain types of
PVC. The product complies with the
European norm for toy safety EN71-3.
SILICONE PAPER
MEASUREMENT/BOX CONTENT
AL180
C4
C4
AL180
B100D
G160D
G160D
B145D
32
32
32
32
Average Values
PE WHITE
MATT
Weight (g/m2)
Weight Total Laminate (g/m2)
Thickness (µm)
Thickness Total Laminate (µm)
Tensile Strength
ISO 1924/2 (kN/m MD)
Gloss (60 °C)
Opacity (%)
Shelf life of laminate* (years)
x
x
x
x
46
46
46
46
cm/175
cm/200
cm/200
cm/250
sheets
sheets
sheets
sheets
per
per
per
per
box
box
box
box
PP CLEAR
GLOSS
PP WHITE
GLOSS
PET CLEAR
GLOSS
100
210
170
280
53
235
58
260
53
240
58
260
110
240
75
225
1.8
–
95
2
10
88
–
2
11
93
80
2
–
93
–
2
Average Values (measured on glass)
Adhesion (FTM1) after 24h (N/25mm)
Adhesion (FTM2) after 24h (N/25mm)
Initial adhesion/tack (FTM9)
Shear Strength (FTM8)
Recommended minimum
application termperature (°C)
Heat resistance
up to 24h (°C)
up to 1h (°C)
Resistance to cold* (°C)
Ageing stability**
DURO AL180
NONPERM C4
7
13
150
3
2
15
> + 10
> +2
+ 80
+ 110
- 20
very good
+ 90
+ 100
- 40
very good
* Not fully resistant until adhesion reaches full strength-after at least 24hrs
** If not exposed to direct sunlight.
Average Values
SILICONE PAPER
B 110D
is a very stable, siliconized special-purpose
paper with good die-cutting and flatness
properties.
ADHESIVE
* Refers to adhesion and printability when stored in original packaging in dark, dry conditions at a temperature
of 22 °C ± 2 °C and a relative humidity of 50 % ± 5 %.
ADHESIVE
* Not fully resistant until adhesion reaches full strength-after at least 24hrs
** If not exposed to direct sunlight.
SILICONE PAPER
sheets
sheets
sheets
sheets
FACE MATERIAL
Weight (g/m2)
Thickness (µm)
94
95
B 100D
is a very stable, siliconized special-purpose
paper which displays good flatness and die
cutting properties.
B 145D
is a siliconized, special-purpose lightweight
board, which displays high dimensional
stability.
G 160D
is a very stable, siliconized, wood-free
board, matt on reverse side and PE-coated
on both sides. It is dimensionally stable and
insensitive to moisture.
Average Values
B 100D
B 145D
G 160D
Weight (g/m2)
Thickness (µm)
87
90
128
135
160
182
JAC GRAPHICS
DIGILABEL
Each product a direct hit
Storage and Conditioning.
Store the material in the original packaging. When just part of the packed sheets is used, close the packaging properly to avoid
moisture exchange.
Prior to printing it is of prime importance to have the self-adhesive material acclimatized to print-room conditions. This has to be
done in the original packaging to avoid moisture exchange.
Printing.
Offset Litho
All Paper products are compatible with conventional offset litho processes, the Film products are not.
HP Indigo
All sheets are cut long grain to ensure proper feeding. Digilabel materials have been successfully printed on HP Indigo printers.
When printing on films select carefully from Advanced Properties on the printer driver, media and thickness / substance settings
e.g. microns / gm2 . Ensure that the total thickness/grammage for the laminate (both face and backing paper) is entered
Note that blanket temperature and time can influence ink anchorage. Blanket temperature can be set between 125 and 140 °C.
Test at intervals of 5 °C if necessary.
Laser Copier/Printers
Digilabel materials have also been successfully printed on toner based laser copier/printers. When printing on films select carefully
from Advanced Properties on the printer driver, media and thickness / substance settings. e.g. microns/gm2 . Ensure that the total
thickness/grammage for the laminate (both face and backing paper ) is entered
• When printing on PE White Matt use setting for Uncoated Paper
• When printing on PET Transparent Gloss use setting for Over Head Transparencies (OHP)
• Both PP White and PP Transparent Gloss are not suitable for toner fuser printing and should not be used
Kiss-/Die-cutting.
The self-adhesive materials for Digital printer can be handled like standard self-adhesive materials when it comes to kiss- or
die-cutting. It is advised to use single-beveled dies for paper and double-beveled / laser hardened dies for films.
Guillotining.
Lowest possible clamping bar pressure, low stacks and sharp, hardened steel knives may give the best results i.e. no adhesive
bleed on cut sheets.
Application.
Again acclimatize the printed samples before applying to the intended surface. Under high humid conditions, paper based labels
may wrinkle after being applied if not conditioned.
Ultimate bond is generally achieved after 24 hrs.
For further information please check our website www.jacgraphics.com
You will find the info by choosing “DOWNLOADS” – “GUIDELINES FOR USE” – “OFFSETPRINTING”.
Your JAC Graphics Distributor
Edition February 2005. A later edition will render this one obsolete.
Guarantee and Liability
All information contained herein reflects our current experience. It is the responsibility of the purchasers to determine the suitability of the product for their application prior to use, also with
regard to possible applicational influences. Any guarantee or liability claims are subject to our current general terms of trade, unless mandatory statutory provisions should provide otherwise.
We reserve the right to make technical improvements to the listed products without notification.
www.jacgraphics.com
N
IS
O
DI