~estWhip1nc.
ENGLISH
6727 NW16th Terrace
Fort Lauderdale, FL 33309
Operating Instructions
for Soda Plus
Thank you for choosing Soda Plus, a genuinely
versatile and high quality-carbonating device. With
Soda Plus you can create a multitude of fizzy cold
drinks for your home use. Use pure water or any
mixtures with syrups, juices, wine etc. and you can
even add ice cubes and carbonate it all together inside
the Soda Plus. Please note, that only liquids with
moderate amounts of ice that can float freely inside
the liquid may be used, please use edible mixtures with
high water content only (DO NOT fill in any pulpy or
thick sauces or creams or any non food substances).
The beautiful stainless steel bottle perfectly fits onto the
dinner table, bar or you take it along for tracking or
picnic. Please read the instructions thoroughly before
using the first time!
Instructions for use
lW
Bottle Dishwasher Safe
Please read these instructions carefully and keep them
for further reference. Prior to first use rinse the bottle
and parts with fresh water.
1. Please firmly insert the measuring tube/filling aid into
the bottleneck and fill with cold water (or juice, add
syrup, wine or other liquid mixtures and add ice
cubes etc.). Please note that the liquid should be cold .
The device must not be used with warm or hot liquids.
Please do not fill with liquid creamy or thick liquid
ingredients. Fill until the liquid becomes visible at the
bottom of the funnel. After filling please remove the
measuring tube, now you should see the correct
filling level as shown in picture 3.
2. The max filling capacity is 1.2 lit/1 .27 US-qt /40.6 US-oz.
3. Screw the head on firmly (please avoid cross
threading by turning the head in a straight position)
but do not use excessive force . Place a C02 8g Soda
charger in holder. For guaranteed quality, please use
original C02 Soda chargers only.
4. Screw the holder with the charger onto the head until
the gas is released with a hissing sound . Charge
with 1 charger, if certain mixtures require more fizz
you may add a second charger. Please shake device
well after each charger! The button on the head will
pop out indicating that you have pressurized the Soda
Plus.
5. Shake the Soda Splash 10-15 times to mix the gas
well with the liquid. Remove the charger holder and
dispose of charger, chargers can be recycled as pure
steel.
6. Let the Soda Plus rest 3-5 minutes (if you are
carbonating wine into sparkling wine, put the
pressurized Soda Plus. into the refrigerator for a
few hours to achieve finer bubbles and stronger
carbonation), then press the button to release the
excessive pressure. The gas will escape on the side
of the head and can be cold, therefore please do not
block the hole with your hand and do not point at
eyes, face or other body parts to avoid uncomfortable
cooling of the skin by the cold gas or an occasional
spray of liquid .
7. Remove the head, slowly pour the carbonated drink
and enjoy.
8. Please use the cap to keep the fizz inside the bottle
and store in refrigerator.
9. Note that after some time or after storage, some
pressure will build inside the bottle, therefore slowly
unscrew head or cap to allow pressure to escape.
Helpful hints
1. To get a better result, please cool the Soda Plus
well under cold water or in the refrigerator before filling.
Do not use the device with warm or hot liquids!
2. Shake the Soda Plus well after filing and
pressurizing, it will result in better carbonation.
3. The longer you let the pressurized liquid rest inside
the Soda Plus (max 24 hours), the better the
carbonation will be.
4. Please do not use with creamy or thick liquids!
Some mixtures, such as sirups or Juices with high
sugar content or flat beer or soda which you want to
fizz up again will create much foam inside the Soda
Plus. Please let such ingredients rest for about 3 to
5 min after pressurizing and then carefully and slowly
press the button intermittently (pointing the exhaust
hole away from face or body) to avoid that the foam
sprays out throiugh the exhaust hole. If such spraying
still appears, please place a kitchen towel at the hole
to absorb the drops or foam of the liquid.
5. For repairs always return the entire unit (head plus
bottle and charger holder). For spare parts, please
contact your dealer directly.
Troubleshooting
The charger is not pierced open:
An unsuitable charger has been used or charger was
inserted incorrectly. Use original C02 Soda chargers
and place it in the charger holder as shown in Fig. 3.
You have not pressed the button, nevertheless,
pressure (and/or liquid) sprays out of the exhaust hole :
a) You have over filled the Soda Plus or used too
many chargers, or the content has warmed up after
pressurizing, so the built in safety valve has opened
and is releasing excessive pressure.
This will automatically stop after the correct pressure
has been reached, but if you want you can also press
the button to accelerate the process.
b) The pressure release button is damaged . Send the
appliance to your dealer.
When the charger is being screwed in, gas escapes
between the bottle and the head:
a) The head gasket is missing. Insert a head gasket
(0-ring) in the head.
b) The head gasket is damaged. Insert a new gasket
(0-ring).
c) The head is not screwed on firmly enough. Screw the
head onto the bottle firmly in accordance with the
instructions for use.
d) The upper edge of the bottleneck, or the head is
damaged. Send appliance to your dealer.
Content is not fizzy after carbonation :
a) The Soda Plus was not shaken firmly or often
enough. Carbonize again and shake firmly.
b) The Soda Plus was overfilled. Always observe that
there is enough space left above the filling level, it is
needed to allow the C02 gas to go into the bottle and
to mix well with the liquid when you shake it.
c) The content requires more chargers than one.
Use a second charger to get a stronger fizz. Please
remember to shake well after EACH charger, do not
use 2 chargers in a row without shaking in between!
Safety Instructions
1. Please keep this instruction booklet for later
reference to avoid any improper handling or
operating. This Soda Plus is designed exclusively
for the purposes specified in this manual. Only use
for normally drinkable liquids and maybe add small
amounts of ice. The device must not be used with
warm or hot liquids. Please use edible liquids only.
Do not fill with any solid, pulpy, creamy or thick liquid
ingredients. This unit is designed for commonly used
carbonated drinks with high water content, and is for
home use only!
2. The Soda Plus and the charger are pressure
containers which require increased attention and
care.
3. Please note the safety instructions for chargers on
the charger packaging.
4. Keep original C02 Soda chargers and the Soda
Plus out of the reach of children.
5. For safety reasons, do not bend or lean over the
Soda Plus when screwing in the charger with the
charger holder.
6. The Soda Plus head screws easily onto the bottle
in an up right (straight) position. Do not cross-thread
by tilting the head which could cause great danger.
7. All Soda Plus parts can be assembled easily;
therefore never use force.
8. Never use the Soda Plus if damaged. If the Soda
Plus has been dropped, it should be checked by
your dealer or an authorized service center.
9. Only unscrew the Soda Plus head when gas has
completely escaped. Press the release button until
the hissing sound stops.
10. Do not expose original C02 Soda chargers or the
Soda Plus to heat (stove, sunlight, oven,
microwave, etc.).Do not store the Soda Plus or
any of its parts in the freezer. Always store inside
the refrigerator!
11 . Please be advised that tampering with the Soda
Plus and/or its components automatically voids
any and all warranties/guarantees of the
manufacturer/supplier.
12. When pressing the release button, please be careful
not to point the exhaust hole in the direction of your
or others eyes or bodyparts, because gas or liquid
might spray out with force and cause irritation,
injury or damage.
13. After charging and taking of the charger holder, be
aware that the charger might be very cold, therefore
do not touch it with bare fingers or body parts.
14. Before unscrewing the head of the Soda Plus,
always press the release button to depressurize the
bottle. After time or storage with the head or the cap
screwed onto the bottle, there will always build up
some pressure from C02 that is released from the
liquid content, therefore slowly unscrew head or cap
to allow pressure to escape via the threads, just like
you do with other soda bottles.
15. Do not attempt to disassemble the release button or
gas inlet valve, these parts are NOT for disassembly!
The only removable parts are the head, the cap the
measuring tube and the charger holder.
Cleaning
Before opening, allow remaining pressure to escape by
pressing the release button or slowly unscrewing cap,
until no more gas is discharged.
Follow steps 1, 2 and 3 to clean your Soda Plus
1. Unscrew the head then rinse it under lukewarm water.
If some spraying has previously occurred with liquids
other than water, press the release button while
rinsing the inside of the head well. If necessary add a
mild detergent and use a soft brush to clean the
thread and the head.
2. Thoroughly clean the bottle, especially the thread
inside the neck, if you wish you may put the stainless
steel bottle (BUT NEVER THE HEAD) inside the
dishwasher.
3. For storage, allow all parts to dry well and reassemble
them only if they are completely dry!
4. Do not use any sharp objects, abrasive materials or
temperatures above 50°C or 120° F, when cleaning the
Soda Splash or any of it's parts.
Warranty
Defective Soda Plus (faulty materials or bad
workmanship) will be repaired without charge
(freight prepaid!) within one year of date of purchase
per valid invoice. This warranty does not cover any
liability for malfunction caused by improper use, use of
damaged/wear parts, or any consequential damage. In
order to assure the proper functioning of your Soda
Plus only use original Soda Plus parts. In
particular, we shall not satisfy any warranty or liability
claims for malfunction, damage, and consequential
damage resulting from any failure of complying with
and/or failure to read this manual and the safety
instructions contained therein.
SAFETY PRECAUTIONS:
1. The Soda Plus and the C02 (Soda) chargers are
pressurized containers and should always be
handled with care and attention.
2. Use only original or authorized parts. Never
substitute parts or products that are not authorized
replacement parts.
3. Do not attempt to make any modifications to the
Soda Plus yourself.
4. Any attempt to repair the Soda Plus yourself or
any improper manipulaton of the Soda Plus will
terminate all warranties and liablilities.
5. If the Soda Plus is damaged, do not use it again.
When the Soda Plus is dropped and/or damaged
with a dent, please call your distributor to return it
to the factory for safety check.
6. For spare parts, please contact your dealer.
7. Please keep the instruciton booklet.
8. Only use original C02 chargers.
9. Keep Soda Plus and chargers out of reach of
small children.
10. Before unscrewing head always press pressure
release button until you hear no sound and no gas
is released.
11. All parts can be assembled in an easy way. Do not
use force.
12. For safety reasons , do not bend over the Soda
Plus while charging.
13. Do not expose the Soda Plus to heat (stove, sun,
oven, microwave, etc.) Do not put the Soda Plus
in the fridge or freezer.
14. Only remove parts in fig . 1 when cleaning the Soda
Plus.
15. Do not use any sharp objects or abrasive materials
to clean the Soda Plus.
16. Do not use sharp detergents or chemicals for
cleaning, do not clean the head or any plastic part
in the dishwasher.