Model ..-XPE-43 Explosion-Proof Enclosures
For MINI-SCREEN ® , MICRO-SCREEN ® , or EZ-SCREEN ™ Emitters and Receivers
Features
• Explosion-proof enclosures for light screen emitters or receivers
- Model MS-XPE-43 includes hardware to mount 32", 36", or 40" MINI-SCREEN
emitter or receiver
- Model US-XPE-43 includes hardware to mount 32", 36", or 40" MICRO-SCREEN
emitter or receiver
- Model SS-XPE-43 includes hardware to mount 750 mm, 900 mm, or 1050 mm
EZ-SCREEN emitter or receiver
• Cast aluminum box and cover are designed and manufactured to be in compliance
with UL and CSA for the following hazardous atmospheres, per NEC Article 500:
Class I, Division 1, Groups C & D and Class II, Division 1, Groups E, F, & G
• Inside of housing is pre-drilled and tapped for mounting hardware
• Standard 3/4"-NPT access is provided at bottom of enclosure for user-supplied
explosion-proof conduit and fittings
Hardware
Hardware included with model MS-XPE-43 (for MINI-SCREEN; see Figure 1):
(2) Brackets
(4) M4 x 0.7 x 10 mm long Sems screws (fastens emitter or receiver to top
bracket)
(1) M30 washer (for bottom bracket)
(1) M30 nut (fastens emitter or receiver to bottom bracket)
(4) Anti-vibration mounts
(4) M4 Keps nuts
Hardware included with model US-XPE-43 (for MICRO-SCREEN; see Figure 2):
(2) Brackets
(4) M3 x 0.5 x 7 mm long Sems screws (fastens emitter or receiver to bracket)
(4) M6 x 1 x 8 mm long screws (fastens brackets to enclosure)
(1) Wrench
Hardware included with model SS-XPE-43 (for EZ-SCREEN; see Figure 3):
(2) Brackets
(4) M5 x 0.5 x 7 mm long Sems screws (fastens emitter or receiver to bracket)
(4) M6 x 1 x 8 mm long screws (fastens brackets to enclosure)
(1) Wrench
!
WARNING . . .
To prevent ignition of hazardous atmospheres, all wiring must be contained in explosion-proof conduit, which has a suitable
rating for the specific environment. All conduit runs must be terminated at the enclosure, using an explosion-proof conduit
fitting which is suitable for the specific environment. Refer to Article 500 of the National Electrical Code, or the equivalent code
for your country, for more information.
Always disconnect all sources of electrical current before opening the enclosure. Keep the enclosure tightly closed whenever any
electrical circuit is “alive.”
Printed in USA
11/04
P/N 64216 rev. A
Model ..-XPE-43 Explosion-Proof Enclosures
(4) Anti-Vibration
Mounts
(4) M3 x 0.5 x 7 mm
Sems Screws
(4) M4 x 0.7 x 10 mm
(2) Mounting Brackets
(1) Top
Mounting Bracket
(2) M6 x 1 x 8 Screws
(4) M4 Keps Nuts
MINI-SCREEN
emitter or receiver
MICRO-SCREEN
emitter or receiver
(1) Bottom
Mounting Bracket
(1) M30 Washer
(1) M30 Nut
NOTE: All mounting hardware
except spacers is supplied
with MINI-SCREEN emitter
or receiver.
Figure 1. Model MS-XPE-43 housing with sensor mounting
hardware
Figure 2. Model US-XPE-43 housing with sensor mounting
hardware
Banner Engineering Corp. • Minneapolis, MN U.S.A.
2
P/N 64216 rev. A
www.bannerengineering.com • Tel: 763.544.3164
Model ..-XPE-43 Explosion-Proof Enclosures
(4) M5 x 0.5 x 7 mm
Sems Screws
(2) Mounting Brackets
(4) M6 x 1 x 8 Screws
EZ-SCREEN
emitter or receiver
Figure 3. Model SS-XPE-43 housing with sensor mounting
hardware
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 64216 rev. A
3
Model ..-XPE-43 Explosion-Proof Enclosures
Mounting for 32"
MICRO-SCREEN or
MINI-SCREEN, or
750 mm EZ-SCREEN
(Hardware Supplied)
1016 mm
(40.0")
Mounting for 36"
MICRO-SCREEN or
MINI-SCREEN, or
900 mm EZ-SCREEN
(Hardware Supplied)
1321 mm
(52.0")
Mounting for 40"
MICRO-SCREEN or
MINI-SCREEN, or
1050 mm EZ-SCREEN
(Hardware Supplied)
254 mm
(10")
User-supplied
Explosion-proof
Conduit and Fitting
(See Warning)
76.2 mm
(3.00")
197 mm
(7.75")
3/4" NPT
Tap Thru
203
(8.0")
Figure 4. Explosion-proof enclosure dimensions and features
WARRANTY:
Banner Engineering Corp. warrants its products to be free from defects for one year.
Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found
to be defective at the time it is returned to the factory during the warranty period. This warranty does
not cover damage or liability for the improper application of Banner products. This warranty is in lieu
of any other warranty either expressed or implied.
P/N 64216 rev. A
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: 763.544.3164 • www.bannerengineering.com • E-mail: [email protected]