In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
This list identifies works approved by Lloyd’s Register Group Limited (LR) for refining and
the manufacture of aluminium alloy plates, sections, bars and castings in accordance with
the requirements of LR's Rules for the Manufacture, Testing and Certification of Materials,
Chapter 8.
The information listed for each works is a summary of the product, grade and maximum
thickness (for round bar, maximum diameter and for castings, maximum weight)
Where required further information should be obtained from the current certificate of
approval issued to the manufacturer by LR.
Works designated "MQS Approved" are also approved under the Materials Quality Scheme
in accordance with LR's Rules for the Manufacture, Testing and Certification of Materials,
Chapter 1 Section 2.
Approval only covers the manufacturing location listed, it does not extend to other works
owned by the same company.
The local LR surveying office is also listed.
Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers,
employees or agents are, individually and collectively, referred to in this clause as 'Lloyd's
Register'. Lloyd's Register assumes no responsibility and shall not be liable to any person
for any loss, damage or expense caused by reliance on the information or advice in this
document or howsoever provided, unless that person has signed a contract with the
relevant Lloyd's Register entity for the provision of this information or advice and in that
case any responsibility or liability is exclusively on the terms and conditions set out in that
contract.
As at 23 May 2017
© Lloyd’s Register Group Limited 2017. All rights reserved.
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Max Thickness/Diameter
(mm)
Category
Grades
Office
Sections
Bars
6082-T5, 6082-T6
6082-T5, 6082-T6
22.00
22.00
Melbourne
Sections
6082-T6
40.00
Sydney
Plates
5083-H116, 5086-H116
5083-H321
5083-H111
3003-H14*
63.50
76.20
150.00
7.00
Vienna
304.00
Vienna
3003-O*, 3003-H12*
3003-H14*
3003-O*, 3003-H12*
3003-H14*
0.45
6.00
0.45
6.00
Antwerp
6005A-T6, 6082-T6
10.00
Antwerp
Australia
CAPRAL ALUMINIUM LIMITED
151, Barry Road
CAMPBELLFIELD
VIC 3061
Tel: +61 (0)3 9358 8138 Fax: +61 (0)3 9357 9952
eail to: [email protected] web: www.capral.com.au
Certificate # MD00/4126/0002/6a Expiry date: 26/02/2019
G. JAMES EXTRUSION CO., PTY., LTD.
26 Long Street,
Smithfield NSW 2164,
Tel: +61 7 3877 2785 Mob: 0402 894 605
email: [email protected] web: www.gjames.com
Certificate No: MD00/4621/0001/6a Expiry Date: 11/10/2019
Austria
AMAG ROLLING GmbH
Coils
A-5282 Ranshofen
P.O. 32
tel: +43 7722 801 3697 fax: +43 7722 809 511
E-Mail: [email protected] Web http://www:amag.at
*Approved applications only.
Certificate # MD00/3189/0007/6a Expiry date: 16/09/2017
HAMMERER ALUMINIUM INDUSTRIES GmbH
Lamprechtshausener Straße 69
5282 Ranshofen.
Tel No. +43 7722 891 0
Refining & Semi Finished Al-Mg-Si grades
Fax No: +43 7722 891 458
E-mail: [email protected]
Website: www.hai-aluminium.at
Certificate No: MD00/4636/0001/6a
Expiry Date: 30/11/2019
Belgium
ALERIS ALUMINIUM N.V.
Coils
Plates from coils
A.Stocletlaan 87
B-3570 Duffel
Tel: +32 (0)15 30 26 40 Fax: +32 15 30 26 22(0)
Email to: [email protected] Web: http://www aleris-duffel.com
Certificate #: MD00/4462/0001/6a
Expiry date: 31/03/2018
* for approved applications only
SAPA RC PROFILES NV/SA
Sections
Kortemarkstraat 52.
BE-8810
Lichtervelde
Tel: +32 51 72 97 14
Email: [email protected]
Web: http//:www.sapagroup.com
Certificate Number: MD00/3856/0003/6a Expiry date: 06/11/2019
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
2
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Max Thickness/Diameter
(mm)
Category
Grades
Office
Castings
Al-Si7Mg
1150.00
Toronto
Al-Si7Mg
75.00
Vancouver BC
Al-Si7Mg
100.00
Vancouver BC
Canada
CAF INNOVATIVE SHAPECASTING
458 Dobbie Drive
Cambridge,
Ontario,
N1T 1ST
Tel: 519 624 9997 Fax: 519 624 0789
email: [email protected] web: www.shapecasting.com
Certificate No:MD00/4536/0001/6a Expiry Date: 20/12/2018
Approval includes grade A356-T6 to ASTM B26 for approved applications.
Heat treatment is sub contracted.
HASTINGS BRASS FOUNDRY LTD.
236 Clark Drive
Vancouver, BC
V5L 3H3
Castings
Tel: +1 604 253 2811 Fax: +1 604 253 3133 Email to: [email protected]
Approval includes ASTM B26/B26M-12 Grade 356
Certificate Number: MD00/4325/0001/6a Expiry date: 28/05/2017
PACIFIC MAKO
Castings
5481-268 Street,
Langley, BC
V4W 3W1
Tel: +1 604 856 6668 Fax: +1 604 856 6512
email: [email protected] web: www.pacmak.com
Approval includes ASTM B26 grade A356.0-T6, accepted for approved applications.
Not approved for weld repairs.
Certificate No: MD00/4570/0001/6a Expiry Date: 24/04/2019
China, People's Republic of
ALERIS ALUMINUM (ZHENJIANG) Co., Ltd.
Refining & Semi Finished 5083, 5086
Plates
5083-O, 5083-H116, 5083-H112,
5086-H116
Nanjing
50.00
No. 1 Cai Jia Road,
Jing Kou Industrial Park
Zhenjiang, Jiangsu, 212141
Tel : +86 511 85307347
E-Mail : [email protected]
Web: http://www.aleris.com
Certificate #: MD00/4332/0001/6a
Expiry date: 06/06/2017
CHONGQING FENGHE ALUMINIUM CO. LTD
74-2, Lvcheng Boulevard,
Xipeng
Jiulongpo District,
Chongqing City. 401326
Refining & Semi Finished 6082
Wuhan
Tel: +86-23-65800038 Fax: +86-23-65800849
E-mail: [email protected]
74-2, Lvcheng Boulevard,
Xipeng,
Jiulongpo District
Chongqing City. 401326
Certificate No: MD00/4513/0001/6a
Expiry Date: 30/09/2015
DYNACAST (SUZHOU) LTD.
No. 389 South JingTang Road
QianDeng, KunShan
215341
Castings
Al-Si9Cu*
1.05
Shanghai Port
Tel: +86 512 5772 5588 Fax:+86 21 5774 1320
Web: www.dynacast.com
Certificate #: MD00/4500/0001/6a Expiry date: 19/07/2018
HENAN ZHONGFU INDUSTRIAL Co., Ltd.
Refining & Semi Finished Al-Mg grades
Plates
5083-O, 5083-H111, 5754-O,
5754-H111
Coils
5083-O, 5083-H111, 5754-O,
5754-H111
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
3
Wuhan
50.00
8.00
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Yulian Industrial Zone,
Zhanjie Town,
Gongyi City,
Henan Province,
Category
Grades
Castings
Al-Si7Mg, AlSi7Mg0,3*
Max Thickness/Diameter
(mm)
Office
Tel: +86 0371 85613658 Fax: +86 0371 85613706
Certificate No.: MD00/4494/0001/6a Expiry Date: 29/06/2018
JINGYI ALUMINIUM PRECISION CASTING Co. LTD
Tongjia Industrial Park,
Qinglong,
Tianning District, Changzhou,
Jiangsu.
12.00
Jiangyin
555.00
43.00
Qingdao
Tel: 00-86-519-85501188 Fax: 00-86-519-85505768
E-mail: [email protected]
Website: www.jingyicasting.com
Certificate No. MD00/4560/0001/6a
Expiry Date: 22/03/2019
LONGKOU CONGLIN ALUMINUM CO., LTD.
Refining & Semi Finished Al-Mg-Si grades
Sections
6005A-T6, 6061-T6, 6082-T5, 6082-T6
Conglin Industry District
Longkou City
Shandong Province 265705
Tel: +86 535 8562517
Fax: +86 535 8563202
Certificate #: MD00/4430/0001/6a
Email to: [email protected]
Web: http://www.conglin.com.cn
Expiry date: 03/02/2018
SAPA CHALCO ALUMINIUM PRODUCTS (CHONGQING)
COMPANY LTD
Xipeng Aluminium Industrial Park
Jiu Longpo District,
Chongqing.
401326
Sections
6082-T6
18.00
Wuhan
Sections
Bars
6061-T6, 6082-T6, 6063-T6*
6061-T6, 6082-T6, 6063-T6*
15.00
80.00
Jiangyin
Xipeng Aluminium Industrial Park,
Jiu Longpo District,
Chongqing. 401326
Tel: +86 023 61968222 Fax: +86 023 6198408.
E-mail: [email protected]
Website: www.sapachalco.com
Certificate No: MD00/4512/0001/6a
Expiry Date: 27/09/2015
SAPA EXTRUSION (JIANGYIN) CO LTD
Jiangyin
No: 888, Shiji Avenue (S), Zhouzhuang Town,
Jiangyin City,
Jiangsu Province. Post Code: 214423
Tel No: +(86) 510 86909818 Fax No: +86 510 86909880
Email: [email protected]
Website: www.sapagroup.com
Certificate No: MD00/4433/0001/6a Expiry Date: 14/02/2018
SHANDONG NANSHAN ALUMINIUM Co. , LTD
Refining & Semi Finished 5083
Plates
5083-O, 5083-H116, 5083-H112,
5083-H321
Qingdao
50.00
Plate and Sheet Company
Donghai Industrial Park,
Xufu Town, Longkou City,
Shangdong Province.
Tel: + 86 535 8785086
Fax: + 86 535 8785086
Website: www.nanshan.com.cn
Certificate No. MD00/4645/0002/6a Expiry Date: 28/12/2019
SOUTHWEST ALUMINIUM (GROUP) CO., LTD.
Plates
5083-O, 5754-O
5083-H112, 5754-H112
5083-H321
5086-O, 5086-H111, 5086-H112,
5086-H116, 5456-H116, 5456-H321
2618-T6
Forgings*
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
4
5.00
30.00
40.00
50.00
Wuhan
500.00
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Xipeng
Jiou Long-po District,
Chongqing City
Chongqing City,
Category
Grades
Max Thickness/Diameter
(mm)
Office
Grade 5754 plate is acceptable for approved applications not in direct contact with seawater,
*Accepted for approved applications.
Tel: +86 (23) 65808767 Fax: +86 23 65808767
Email: [email protected]
web: www.cqswa.cn
Certificate #: MD00/2921/0007/6a Expiry date: 12/10/2017
YUANXING LOCOMOTIVE PARTS (LINHAI) LTD
Industrial Park
Youxi Town,
Linhai City.
Zhejiang Province
Castings
Al-Si7Mg
0.01
Shanghai Port
Forgings*
7022-T6, 2618A-T6
20.00
Prague
Forgings*
2618A-T6
61.00
Prague
Castings
Al-Si10Mg
116.00
Prague
Tel: 139-0676-7679
E-mail: yuonxing_k263.net
Certificate No: MD00/4629/0001/6a
Expiry Date: 07/11/2019
Czech Republic
ALCAN STROJMETAL ALUMINIUM FORGING s.r.o.
Ringhofferova 66,
251 68 Kamenice
Tel: +420 204 672 302 Fax: +420 204 672 028
Certificate #: MD00/3898/0002/6a Expiry date: 23/03/2017
CZECH PRECISION FORGE A.S.
Tylova 1/57
301 00 Plzen
Tel: + 420 378 133 802 Fax: +420 378 132 516
E-mail: [email protected]
Website: www.cpforge.com
Certificate No: MD00/3049/0003/6a Expiry Date: 09/02/2020
SLEVARNA A MODELARNA NOVE RANSKO, s.r.o.
Nove Ransko 234
582 63 †dírec nad Doubravou
Tel No +420 569 669 480 Fax No. +420 569 669 487
E-mail: [email protected]
Website: www.slevarna.cz
Certificate #: MD00/4186/0002/6a
Expiry date: 22/06/2019
France
CONSTELLIUM ISSOIRE
Refining & Semi Finished Al-Mg grades
Plates
5086-H116, 5086-H321
5086-O, 5086-H111, 5086-H112
5083-H116
5383-H116, 5383-H321
5083-O, 5083-H111, 5083-H112,
5083-H321, 5383-O, 5383-H111,
5383-H112
Lyon
30.00
40.00
50.00
80.00
170.00
Flat Rolled Products
Rue Yves Lamourdedieu
Zl des Listes
63502 Issoire Cedex
Tel: +33 4 7355 5050 email: [email protected] web: www.constellium.com
Materials Quality Scheme approved - MQS 037
Certificate #: MD00/1241/0011/6a Expiry date: 25/02/2019
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
5
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Max Thickness/Diameter
(mm)
FORGES DE BOLOGNE
39 rue des Forges
BP 82138 BOLONGE
52310 BOLOGNE
Forgings*
7175-T6
220.00
Lyon
5083
200.00
Lyon
Tel: +33 3 25 32 80 13
Office
Fax: +33 3 25 32 39 21 Email to: [email protected]
Certificate #: MD00/4324/0001/6a Expiry date: 27/05/2017
L'UNION DES FORGERONS
12 Rue De La Pierre Follège
BP 16 - Z.A.
91660 Méréville
Forgings*
Tel: +33 (0) 1 64 95 02 25 Fax: +33 (0) 1 64 95 09 89
Email: mailto:[email protected]
Web: http://www.union-des-forgerons.fr
Certificate #: MD00/3229/0004/6a Expiry date: 23/03/2018
SABART AERO TECH - Tarascon sur Ariege France
BP 29,
09401 Tarascon sur Ariege Cedex
Refining & Semi Finished 7175-O*
Marseille
Tel no: +33 561 024 064
Fax no: +33 561 024 011
Email [email protected]
Web:www.sabart-at.com
Certificate no. MD00/4351/0002/6a
Expiry Date 28/07/2018
Appproved supplier to Forges de Bologna
*7175 included in this scope of approval
* for approved appplications only
Germany
AGVS ALUMINIUM-WERKE GMBH VILLINGEN
Goldenbühlstraße 14
78048 Villingen-Schwenningen
Castings
Al-Si10Mg, AlSi7Mg0,3*, AlSi9Mg*
234.00
Hamburg
* For Approved Applications.
Tel: +49 7721 846031 Fax: +49 7721 846051
Email: mailto:[email protected]
Web : www.agvs.de
Certificate No. MD00/3355/0004/ 6a Expiry date: 12/07/2019
ALERIS CASTHOUSE GERMANY GmbH
Schleusenstr. 11
D-46562 Voerde
Refining & Semi Finished All Grades
Hamburg
Tel: +49 0281 164881 4442 Fax: +49 0281 1648814393
Email: [email protected]
Website: www.aleris.com
Approval is for vertical cast billets 202 to 348 mm diameter, maximum weight 2000 Kgs for alloy' series 5xxx and 6xxx.
Certificate: MD00/3665/0004/6a Expiry date: 23/08/2018
ALERIS CASTHOUSE GERMANY GmbH
Carl-Spaeter-Strasse 10
D-56070
Koblenz
Refining & Semi Finished Al-Mg-Si grades, Al-Mg grades
510.00
Hamburg
Plates
70.00
250.00
Hamburg
Tel: 0049 261/891 7527
Email: [email protected] Web: www.aleris.com
Cert Number: MD00/4616/0001/6a Expiry Date: 19/04/2019
ALERIS ROLLED PRODUCTS GERMANY GMBH
5083-H116
5059-O, 5059 H111, 5059 H116, 5059
H321, 5083-O, 5083-H111,
5083-H112, 5083-H321, 5086-O,
5086-H112, 5086-H321, 6061-T6,
6082-T6
5083-O, 5083-H111, 5083-H112,
5083-H321, 5086-O, 5086-H112,
5086-H321, 6061-T6, 6082-T6
5083-O, 5083-H111, 5083-H112,
5083-H321, 5086-O, 5086-H112,
5086-H321, 6061-T6, 6082-T6
Sections
Bars
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
6
250.00
250.00
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Max Thickness/Diameter
(mm)
Office
Carl-Spaeter-Straße 10
D-56070 Koblenz
Tel: +49 (0)261 891-7527 Fax: +49 (0)261 891 9 7527 Email: mailto:[email protected] Web:www.aleris.com
Certificate No. MD00/0697/0011/6a Expiry date: 19/04/2019
ALUMINIUMWERK UNNA AG
Refining & Semi Finished Al-Mg-Si grades, Al-Mg grades
Sections
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5754-O,
5754-H111, 6061-T5, 6061-T6,
6082-T5, 6082-T6
Bars
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5754-O,
5754-H111, 6061-T5, 6061-T6,
6082-T5, 6082-T6
Extrusions
3003-O*, 3003-F*
Hamburg
160.00
160.00
150.00
Uelzener Weg 36
D-59425 Unna
Includes approval for pipes and tubes with 250 mm outer diameter (max.) and 40 mm wall thickness (max).
Tel: +49 2303 206 148 Fax: +49 2303 206 117
Email: mailto:[email protected]
Web: http://www.alunnatubes.com
Certificate No. MD00/3152/0008/6a Expiry date: 16/03/2017
C.F. MAIER LEICHTGUSSWERK GMBH & CO. KG
Königsbronn
Postfach 1165
D-89548 Königsbronn
Castings
Al-Si10Mg, Al-Si7Mg
350.00
Hamburg
Sections
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5086-H112,
6005A-T6, 6061-T6, 6082-T6
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5086-H112,
6005A-T6, 6061-T6, 6082-T6
600.00
Hamburg
Tel: +49 (0)7328 81152 Fax: +49 7328 81193
EMail: [email protected] Web http://www.c-f-maier.de
Certificate No. MD00/2037/0007/6a Expiry date: 11/07/2019
CONSTELLIUM SINGEN GmbH
Bars
600.00
Alusingen Platz 1
D-78224 Singen
Tel: +49 7731 2330 Email: mailto: [email protected] Web:http://www.constellium.com
Certificate No. MD00/2654/0006/6a Expiry date: 16/03/2018
DRAHTWERK ELISENTAL W.ERDMANN GmbH & Co.
Werdohler Strasse 40
58809 Neuenrode
Wire
5019*
9.00
Hamburg
Castings
Al-Si10Mg, Al-Si7Mg
680.00
Hamburg
Plates
5083-O, 5083-H111, 5083-H116,
5083-H112, 5083-H321
5083-O, 5083-H111, 5083-H112,
5083-H116, 5083-H321
10.00
Hamburg
5083-H112, 5083-H321, 5086-O,
5086-H111, 5086-H112, 5086-H321
5083-O, 5083-H111
3003-O*, 3003-H111*
10.00
Tel: +49 2392 69790 Fax: +49 2392 697 8090
E-mail to: [email protected] Web: http://www.elisental.de
Certificate #: MD00/4484/0001/6a
Expiry date: 19/05/2018
* for approved applications only
HAL ALUMINIUMGUSS LEIPZIG GMBH
Gutenbergstraße 20
04178 Leipzig
Tel: +49 341 453 40 850 Fax: +49 341 453 40 890
E-mail: [email protected]
Website: www.hal-gruppe.de
Certificate No. MD00/3363/0005/6a Expiry date: 30/07/2019
HYDRO ALUMINIUM ROLLED PRODUCTS GmbH
Coils
10.00
Works Aluminium Norf GmbH
Grevenbroich
Aluminiumstraße 1
D-41515 Grevenbroich
Tel: +49 (0)2181 66 1381 Fax: +49 (0)2181 661864
Email: [email protected]
Web: http://www.hydro.com
Certificate No. MD00/0095/0007/6a Expiry date: 20/01/2018
HYDRO ALUMINIUM ROLLED PRODUCTS GmbH
Plates
Coils
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
7
Hamburg
12.00
5.00
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Max Thickness/Diameter
(mm)
Office
Aluminiumstraße
21129 Hamburg
Tel:- +49 (0)40 74011-726 Fax:- +49 (0)40 74011-730
email: [email protected] web: www.hydro-aluminium.com/deutschland
Certificate No. MD00/2218/0009/6a Expiry date: 12/06/2019
METALLGIEßEREI GUTSCHERA GmbH
Industriestraße 4
D-59379 Selm
Castings
Al-Si10Mg, Al-Si7Mg
Castings
Al-Si7Mg
Castings
Al-Mg3, Al-Si12, Al-Si10Mg,
Al-Si7Mg, Al-Si5Cu*, Al-Si9Cu*,
Al-Si8Cu3*, Al-Si(Cu)*, Al-Cu4Ti*,
Al-Mg5(Si)*, Al-Zn10Si8Mg*,
Al-Zn15Si8*
750.00
Hamburg
1200.00
Hamburg
750.00
Hamburg
500.00
Hamburg
Tel: +49 (0) 2592/1538 Fax: +49 (0) 2592/20826
Email: [email protected]
Web: http://www.gutschera.de
Certificate No. MD00/2269/0007/6a Expiry date: 18/11/2019
METALLGUSS SEIFERT GMBH
Boschstraße 8 - 10
D-56457 Westerburg / Sainscheid
Tel: 0049 (0) 2663 91540 Fax: 0049 (0) 2663 915429
Email:mail to: [email protected]
Web Page: www.metallguss-seifert.de
Certificate No. MD00/3449/0005/6a Expiry date: 20/11/2018
Metallgießerei an der Mulde GmbH
Muldenhütten 22
D-09599 Freiberg
Tel: +49 (0) 37 31 / 39 69 61 Fax: +49 (0) 3731 39693 Email: mailto:[email protected]
* accepted for approved applications.
Certificate Number: MD00/2745/0005/6a Expiry: 05/10/2018
OHM & HÄNER METALLWERK GMBH & CO. KG
Im Grüntal 1
D-57462 Olpe
Web: http://www.m-adm.de
Castings
Al-Si10Mg, Al-Si7Mg, AlSi9Mg*
Tel: +49 02761/921-457 Fax: +49 02761/921-555
Email: mailto:[email protected]
Web:http://www.ohmundhaener.de
Certificate No. MD00/2257/0007/6a Expiry date: 25/09/2019
OTTO FUCHS KG
Refining & Semi Finished Al-Mg-Si grades, Al-Mg grades
Sections
5083-O, 5086-O, 6061-T6, 6082-T6
Bars
5083-O, 5086-O, 6061-T6, 6082-T6
Forgings*
5083-O, 5083-F, 5083-H321, 5086-O,
5086-F, 5086-H321, 6061-T6, 6082-T6
Hamburg
260.00
160.00
2000.00
Derschlager Straße 26
D-58540 Meinerzhagen
Tel. 49(0)2354 73 897 Fax 49(0)2354 73 201
Email: [email protected]
Web page http://www.otto-fuchs.com
* accepted for approved applications
Certificate No. MD00/0553/0007/6a Expiry date: 05/03/2020
SECO GmbH
Castings
Al-Si12, Al-Si10Mg,
Al-Si12CuMgNi*
0.35
Hamburg
130.00
Hamburg
Gross Orden 23
D-06484 Quedlinburg
Tel: +49 (0) 3946 9079250 Fax: +49 (0) 3946 9079215
Email mailto: [email protected] Web http://www.secogmbh.de
Certificate #: MD00/3525/0003/6a Expiry date: 25/06/2017
ST EXTRUDED PRODUCTS GERMANY GMBH
Sections
6082-T6
WERK BITTERFELD
Devillestrasse 2
06749 Bitterfeld
Tel: +49 (0) 3493 75475 Fax: +49 (0) 3493 75477
Email: [email protected]
Web: http://www.step-g.com
Mechanical testing is carried out by approved test house.
Certificate: MD00/3781/0003/6a Expiry date: 27/04/2019
ST Extruded Products Germany GmbH Werk Bonn
Refining & Semi Finished Al-Mg-Si grades, Al-Mg grades
Sections
5083-O, 5083-H112, 5083-H321,
5086-O, 5086-H112, 5086-H321,
6082-T6
Bars
5083-O, 5083-H112, 5083-H321,
5086-O, 5086-H112, 5086-H321,
6082-T6
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
8
Hamburg
60.00
60.00
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Max Thickness/Diameter
(mm)
Grades
Office
Friedrich Wöhler Straße 2
D-53117 Bonn
Tel: +49 (0) 228 558 2755 Fax: +49 (0) 228 558 2874 Email:mailto:[email protected]
Web:http://www.aleris.com
Including ingots with a maximum diameter of 400 mm.
Certificate No. MD00/1623/0008/6a Expiry date: 03/02/2019
WESERALU GmbH & Co. KG
Sections
Bars
6061-T6, 6082-T6
6061-T6, 6082-T6
250.00
250.00
Hamburg
Am Osthafen 5
D-32423 Minden
Tel +49 (0)571 38705 22
Fax +49 (0)571 38705 55
Certificate #: MD00/1664/0007/6a Expiry date: 12/08/2017
WIELAND-WERKE AG
Email: mailto: [email protected]
Extrusions
Web:http://www.weseralu.de
Al-Mg-Si Grades
76.00
Hamburg
Graf-Arco-Strasse 36
D-89079 Ulm
Tel: +49 731 944 2508 Fax: +49 731 944 4208
Email: [email protected] Web: http://www.wieland.de
The scope of approval is for extruded finned tubes only with a maximum 5mm wall thickness in grades AlMn1 and AlMgSi0.5 supplied in the as extruded
condition, accepted for approved applications.
Certificate Number: MD00/3216/0004/6a Expiry: 27/01/2018
Greece
ANOXAL S.A.
3rd km Inofita-Agios Thomas Road,
32011, Agios Thomas,
Viotia,
Refining & Semi Finished 6005A, 6061, 6082, Al-Mg-Si grades
230.00
Piraeus
20.00
40.00
Piraeus
Tel: +30 226 205 3569 Mob: +30 697 440 3569
email: [email protected]
Certificate No: MD00/4357/0001/6a Expiry date: 03/07/2017
Approval includes grades EN AW 6060 and 6063. Grades not covered by LR Rules are accepted for approved applications only.
COSMOS ALUMINIUM A.E
Sections
Bars
6082-T6
6082-T6
8th km National Road Larissa - Athens,
Larissa,
Tel No: +30 2410 567567 Fax No: +30 2410 567510
Email: [email protected] or [email protected]
Web: www.cosmosaluminium.gr
Certificate No: MD00/4306/0002/6a Expiry Date 06/04/2017
Approval includes bars of square, rectangular, round and hexagonal shapes and section profiles of various shapes (flat or hollow) up to 5mm in thickness
Sections within Circumscribed Circle Diameter maximum 250mm x 5mm thickness.
Bars within Circumscribed Circle Diameter maximum 250mm x 40 mm thickness
ELVAL HELLENIC ALUMINIUM INDUSTRY S.A.
Plates
5083-O, 5083-H111, 5083-H116,
5083-H321, 5086-O, 5086-H111,
5086-H116
12.70
Piraeus
203.00
Piraeus
57 km Athens Lamia National Road
GR-32011 Inofyta-Viotia
Tel: +30 22620 53600 Fax: +30 22620 31347
Email: [email protected]
Web: http://www.elval.gr
Certificate No. MD00/2990/0008/6a Expiry date: 01/09/2018
EPALME S.A.
Refining & Semi Finished Al-Mg-Si grades, 3103*
Inofita, Viotia
32011
Tel: +30 22620 30806 Fax: +30 22620 56300
email: [email protected] Web http://www.epalme.gr
Certificate No. MD00/4303/0001/6a Expiry date: 02/04/2017
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
9
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Max Thickness/Diameter
(mm)
Office
India
HINDALCO INDUSTRIES LTD
Refining & Semi Finished Al-Mg-Si grades, Al-Mg grades
Plates
5083-O, 5083-H112, 5086-O,
6061-T6, 6082-T6
Sections
5083-O, 5083-H112, 5086-O,
5086-H112, 6061-T6, 6082-T5,
6082-T6
Bars
5083-O, 5083-H112, 5086-O,
5086-H112, 6061-T6, 6082-T5,
6082-T6
Chennai
12.50
25.00
50.00
P.O. Renukoot
Dist. Sonbhadra 231217
Uttar Pradesh
Tel: +91 5446 252077-79 Fax: +91 5446 252107/252427
Email: [email protected]
Web: http://www.hindalco.com
Certificate No. MD00/0674/0008/6a Expiry date: 01/04/2019
VULKAN Technologies Pvt. Limited
Castings
Al-Si7Mg
Al-Si12, Al-Si10Mg
12.50
64.00
Mumbai
Sections
6082-T5, 6082-T6
50.00
Milan
Al-Si7Mg
90.00
Venice
GAT No. 539B
Village Kasar Amboli
Pirangut Industrial Area, Tal-Mulashi
Dist. Pune 412115, Maharashtra
Tel: +91 20 6676 5541 Fax: +91 20 6676 5551
email [email protected] web: www.vulkanindia.com
Certificate Number: MD00/3051/0006/6a Expiry: 19/01/2019
Italy
BODEGA G. & C. S.P.A.
Via Binda di Sopra 1
24034 Cisano Bergamasco (BG)
Tel: +39 035 438366 Fax: +39 035 4382300 Email: mailto:[email protected]
web: http://www.bodega.it
Certificate No. MD00/3112/0005/6a Expiry date: 23/10/2019
F.A.M. S.r.l.
Via Pasolini, 38-39
48018 GRANAROLO FAENTINO (RA)
Castings
Tel +39 0546 41494 Fax +39 0546 41441
email: [email protected] web: www.fonderiafam.com
Certificate No. MD00/3288/0005/6a Expiry date: 26/11/2018
Fusina Rolling S.r.l.
Refining & Semi Finished Al-Mg grades
Plates
5083-H128
5083-H116, 5083-H321
5083-O, 5083-H111, 5083-H112
8.00
40.00
60.00
Venice
Sections
30.00
Milan
65.00
Venice
Stabilimento di Fusina
Via dell' Elettronica 31
30176 Malcontenta
Loc. Fusina, Venezia
Tel: +39 041 2917254
Fax: +39 041 2917212
Email: [email protected]
Web page http://www.alcoa.com
MATERIALS QUALITY SCHEME APPROVED - MQS 046
Certificate No. MD00/2605/0013/6a Expiry date: 13/06/2018
METRA S.P.A.
6005A-T5, 6005A-T6, 6082-T5,
6082-T6
Via Stacca, 1
25050 Rodengo Saiano
Brescia
Tel: +39 030 6819205 Fax: +39 030 6810260 Email: mailto:[email protected]
Certificate No. MD00/2975/0005/6a Expiry date: 04/05/2018
SA & BAR S.r.l
Web: http://www.metra.it
Castings
Al-Si7Mg
Via A. Boldrini, 26
Frazione Quarto Inferiore
40057 Granarolo Dell'Emilia (BO)
Tel: +39 051 767022 Fax: +39 051 0547900
Certificate No. MD00/3949/0002/6a Expiry date: 18/09/2017
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
10
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Castings
Al-Si12, Al-Si7Mg
Max Thickness/Diameter
(mm)
Office
Japan
FUKUTATSU ALLOY MFG. CO., LTD.
15, 1, 3 - Chome
Takatsukadai
Nishi-ku
Kobe
700.00
Kobe
Tel +81 78 991 2201 Fax +81 78 991 1523
email [email protected] web: www.fukutatsu.com
Not approved for weld repair.
Certificate No. MD00/0556/0007/6a Expiry date: 04/08/2019
KOBE STEEL, LTD.
Refining & Semi Finished Al-Mg grades
Sections
5083-O, 5086-O, 5154A*
Bars
5086-O, 5154A*
5083-O
Nagasaki
150.00
150.00
360.00
Chofu Works
14-1, Minato-Machi
Chofu, Shimonoseki City,
Yamaguchi Pref. 752-0953
Tel: +81 83 246 3640
Fax: +81 83 346 1710
Email: [email protected]
Web http://www.kobelco.co.jp
* accepted for approved applications
Certificate No. MD00/1947/0008/6a Expiry date: 10/11/2017
KOBE STEEL, LTD.
Forgings*
5083-F
5083-O, 5083-H112
370.00
2055.00
Kobe
Sections
5083-O, 5083-H112
20.00
Kobe
420.00
Yokohama
1200.00
Kobe
300.00
Kobe
Daian Plant
1100, Umedo
Daian-cho
Inabe-city
Mie-ken,
Tel: +81 594 77 2202 Fax: +81 594 77 2249
Email: [email protected]
* accepted for approved applications
Certificate No. MD00/2087/0009/6a Expiry date: 10/04/2017
LIGHT METALS EXTRUSION DEVELOPMENT CO., LTD.
2-2, 2 chome, Higashi Ogoso
Yokkaichi
Mie-ken
Tel: +81 593 45 4775 Fax: +81 593 47 0355 Email: mailto:[email protected]
Includes approval for pipes and tubes with 280mm outer diameter and 20mm wall thickness (max)
Certificate No. MD00/0930/0007/6a Expiry date: 02/06/2017
MIURA CO., LTD.
20-1 Kamitsuru, Aza
Imaizumi,
Sukagawa-city,
Fukushima 962- 0301
Castings
Al-Si7Mg
Castings
Al-Mg3, Al-Si12, Al-Si10Mg,
Al-Si7Mg
Forgings*
5083-O
Tel No: +81 248 86 2662 Fax No: +81 248 86 2663
email: [email protected] web: www.miura1.co.jp
Certificate No: MD00/4136/0002/6a
Expiry Date 01/04/2019
RYOSAN INDUSTRY CORPORATION
57 Eibara Nagao-cho
Kita-ku
Kobe
Tel: +81 (0)78 986 6617 Fax: +81 (0)78 986 4472
Email: mailto:[email protected]
Web: http://www.ryosan-ind.co.jp
Certificate No. MD00/1257/0007/6a Expiry date: 01/12/2017
SEO KOATSU KOGYO CO., LTD.
Ichikawa Works
869-20 Aza Kanzaki Ichikawa-cho
Kanzaki-gun
Hyogo-pref
Tel: +81 790 28 0590 Fax: +81 790 28 1140
* accepted for approved applications
Certificate No. MD00/1338/0007/6a Expiry date: 10/11/2019
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
11
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
UACJ CORPORATION
Refining & Semi Finished Al-Mg grades
Plates
5083-H116
5083-O, 5083-H321
Max Thickness/Diameter
(mm)
Office
Yokohama
35.00
200.00
FUKAYA WORKS
1351, Uwanodai
Fukaya City
Saitama Pref.
366-8511
Tel +81 485 72 1316 Fax +81 485 73 5228
Email: [email protected]
Web http://www.uacj.co.jp
The scope of approval includes for the manufacture of alloy 3003 supplied to ASAHI CHEMICAL INDUSTRY CO. LTD for use for transition joints.
Certificate Number: MD00/1277/0010/6a Expiry: 10/03/2018
UACJ Corporation
Refining & Semi Finished 5083
Plates
5083-O
160.00
Kobe
Refining & Semi Finished 5083
Sections
5083-H112
5083-O
Bars
5083-O
20.00
120.00
600.00
Nagoya Works
3-1-12, Chitose
Minato-ku
Nagoya
455-8670
Tel: +81 52 654 1186 Fax: +81 52 654 0039
Email: mailto:[email protected]
Web: http://www.uacj.co.jp
Certificate No. MD00/1453/0008/6a Expiry date: 14/06/2018
UACJ Corporation
Kobe
UACJ Extrusion Nagoya Corporation
Nagoya Works,
3-1-12 Chitose,
Minato-ku,
Nagoya 455-8670
Tel No: +81 52 654 1108 Fax no: +81 52 654 1189
Email: [email protected]
Web: http://www.suex.uacj-group.com
Includes approval for pipes and tubes with 150mm OD and 30mm wall thickness (max) and approval for pipe and tubes with 280mm OD and 20mm wall
thickness (max) by subcontracted manufacture.
Certificate No: MD00/4047/0004/6a
Certificate Expiry 14/06/2018
UACJ Corporation
Plates
3003-O**
5083-H321
5083-O
15.00
80.00
200.00
Kobe
Fukui Works
21-1 Kurome Mikuni-cho
Sakai City,
Fukui-Pref.,
913 - 8588
Tel No: +81 776 82 5843
Email: [email protected]
Web:
Fax No:
+81 776 82 5854
Materials Quality Scheme Approved - Approval No. MQS010
Certificate No: MD00/ 4230/ 0003/6a Expiry Date: 15/10/2018
* For thickness 29mm and above self annealing 5083 denoted as 5083(SA)
** accepted for approved applications only
UACJ Extrusion OYAMA Corporation
Refining & Semi Finished Al-Mg grades
Sections
5083-O
Bars
5083-O
Yokohama
20.00
200.00
560 Dotou
Oyama City,
Tochigi Pref.
323-0812
Tel no; +81 285 23 2113
Fax No: +81 285 25 0567
Email mailto: [email protected]
Accepted for approved applications
Certificate No:MD00/4261/0010/6a Expiry date 14/02/2018
UACJ Foundry & Forging Corporation
Forgings*
2618-T6
5083-O
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
12
1000.00
2000.00
Yokohama
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Grades
Max Thickness/Diameter
(mm)
Forgings*
5083-O
100.00
Kobe
Sections
Bars
5083-O
5083-O
6061-T6
30.00
50.00
120.00
Changwon
Castings
Al-Si7Mg
300.00
Changwon
Castings
Al-Si7Mg
50.00
Seoul
544.00
Ulsan
68.00
9.00
Seoul
Category
Office
Foundry and Forging Works
560, Dotou,
Oyama City,
Tochigi 323-0812
Tel No: +81 285 24 3611
Fax +81 285 22 2884
Email mailto: takashima. [email protected] group.com
Web http://www.uaccj.co.jp
Certificate number MD00/4267/ 0002/6a
Expiry date 12/02/2018
YAMASHITA TANZOSHO CO., LTD.
43-1 Ikuno
6 Chome Katano
Osaka pref.
Tel: (0)72 891 1421 Fax (0)72 892 2126
* Accepted for approved applications
Certificate No. MD00/3249/0004/6a Expiry date: 21/07/2018
Korea
ALCOA KOREA Ltd.
48, Jeongdong-ro,
Seongsan-gu,
Changwon,
Gyeongnam,
Tel. +82 55 269-9581 Fax +82 55 269-9502 Email to: [email protected]
Web: http://alcoa.com
Certificate No. MD00/2078/0008/6a Expiry date: 31/03/2018
DAESHIN METAL MANUFACTURING CO. LTD
24-11, Palryong-Dong,
Euichang-Gu,
Changwon-City,
Kyungnam.
Tel: + 82-55-296-1011, Fax: +82-55-296-6149
E-mail: [email protected]
Website: www.ds-al.com
Certificate No:
MD00/4546/0001/6a
Expiry Date: 31.01.2019
KOREA LOST-WAX CO., LTD.
#363-74, Gongdan 1-Daero,
Siheung-City,
Gyeonggi-Do, 15074
Tel: +82 31 499 8485 Fax: +82 31 431 6091
email: [email protected] web: www.lostwax.co.kr
Certificate No. MD00/2664/0005/6a Expiry date: 09/03/2020
* Investment castings in alloy A357 accepted for approved applications.
POONGSAN CORPORATION
Angang Plant
2222-2, Sandae-Ri
Angang-Oup
Kyungji-Si
Kyungbu
Angang-eup
Gyeongju-si, Gyeongbuk
Kyungju-Si, Kyungbuk
Forgings*
2618-T6
Plates
Sections
6061-T6, 6082-T6, 6063-T6*
6061-T6, 6082-T6, 6063-T6*
Tel: +82 54 760 6693 Fax:P +82 54 760 6690
email: [email protected] www.poongsan.co.kr
* For Approved Applications only
Certificate No. MD00/3250/0005/6a Expiry date: 24/07/2018
SHIN YANG METAL IND. CO., LTD
162 Sihwaro, Danwon-gu
Ansan-city Kyungki-go
Tel No: +82 31 363 1972
Fax No:+82 31 498 3300
Email: [email protected]
Web: www.shin-yang.com
Certificate No: MD00/4455/0001/6a Expiry Date 27/03/2018
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
13
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
SHIN YANG METAL IND. CO., LTD
BANWOL FACTORY
48, Wonsi-ro
Danwon-gu
Ansan-city Gyeonggi-do
Refining & Semi Finished 6061, 6082, 6063*
Max Thickness/Diameter
(mm)
Office
Seoul
Tel No: +82 31 491 3561
Fax No:+82 31 491 8800
Email:
Web:
Certificate No: MD00/4455/0001/6a Expiry Date 27/03/2018
New Zealand
FLETCHER ALUMINIUM
30-32 Bowden Road
Mt Wellington
Extrusions
6061-T5, 6061-T6
190.00
Auckland
250.00
Auckland
Tel: +64 09 574 1500 Fax: +64 09 573 0418 email: [email protected] Web: http://:www.fletcheraluminium.co.nz
Certificate No. MD00/3077/0004/6a Expiry date: 07/04/2016
ULLEXCO
Extrusions
6061-T5, 6061-T6, 6082-T5, 6082-T6,
6005A-T6, 6261-T6*, 6005A-T5,
6261-T5*
A Division of Ullrich Aluminium
39-45 Maui Street
Pukete Industrial Estate
Hamilton
Tel: +64 (07) 849 5095 Fax: +64 (07) 849 4453 email: [email protected]
web: www.ulrich-aluminium.co.nz
* accepted for approved applications.
Certificate Number: MD00/3071/0005/6a Expiry: 05/03/2019
Norway
ALCOA NORWAY ANS
Postboks 750, 8654 Mosjøen
Refining & Semi Finished 5083, 5086
Oslo
Tel: +47 751 79100 Fax: +47 751 71887
E-mail: [email protected]
Web: http://www.alcoa.com
Approval for semi finished products covers rolling ingots to 630mm max thickness, 2930mm max width and 8600mm max length.
Certificate No. MD00/3358/0004/6a Expiry date: 20/07/2019
BENTELER ALUMINIUM SYSTEMS NORWAY AS
Fabrikkveien
Cast House, Building 123,
2830 Raufoss
Refining & Semi Finished Al-Mg-Si grades
305.00
Oslo
20.00
Oslo
405.00
Stavanger
Tel: +47 81 15 60 00 Fax: +47 61 15 94 87
web: www.benteler.com
Certificate No: MD00/3995/0002/6a Expiry date: 19/10/2017
HYDAL ALUMINIUM PROFILER AS
Sections
6005A-T4*, 6005A-T6, 6061-T6,
6082-T4*, 6082-T6
Raufoss Industripark,
Fabrikkveien, Bygn. No. 232 (vestsiden),
N-2830 Raufoss
Tel: +47 61 15 30 00 Mob: +47 95101796
email [email protected] web: www.hydal.com
Certificate No. MD00/3054/0008/6a Expiry date: 28/01/2019
HYDRO ALUMINIUM A.S. KARMØY
Hydroveien 160
4265 HÅVIK
Refining & Semi Finished Al-Mg-Si grades
Tel no: +47 528 54000 Fax no: +47 528 54380 Mob +47 48028973
Email [email protected]
Web: www.hydro.com
Certificate No: MD00/4328/0001/6a
Expiry date 28/05/2017
Approval includes SFP ingot up to 405mm diameter x 7000mm in length
mechanical testing out sourced
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
14
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Max Thickness/Diameter
(mm)
Forgings*
7022-T6
7.60
Office
Poland
ZAKLAD OBROBKI PLASTYCZNEJ Sp. z o.o.
ul. Kuznicza 13
21- 045 Swidnik
Katowice
Tel No: +48 81 7515008 Fax No: +48 81 4680911 Mob No: +48 504204770
Email: [email protected] or [email protected]
Web: www.kuznia-zop.pl
Certificate no: MD00/4313/0001/6a Expiry date: 01/05/2017
*For Approved Applications
Raw material supply restricted to Grupa Kety SA.
South Africa
HULAMIN LIMITED
Refining & Semi Finished 5083, 5086, 6061, 6082
Plates
5083-O, 5083-H116, 5083-H112,
5083-H321, 5086-O, 5086-H112,
6061-T6, 6082-T6
5083-H111
Sections
5083-O, 5086-O, 6061-T6, 6082-T6
Durban
25.00
30.00
190.00
(Rolled Products)
Moses Mabhida Road
Pietermaritzburg
3200
Tel: +33 396 6911 Fax +33 395 6469 Email mailto: [email protected] Web http://www.hulamin.co.za
Certificate No. MD00/3277/0007/6a Expiry: 11/10/2018
Spain
GRUPO ALUMINIOS DE PRECISION S.L.
Poligon Industrial Villalonquejar
Calle Merindad de Cuesta Urria 26
09001 Burgos
Castings
Al-Si7Mg
Sections
Bars
6082-T6
6082-T6
100.00
Bilbao
30.00
70.00
Gothenburg
Tel +34 947 297 481 Fax +34 947 297 484
email: [email protected] web www.alu-gap.com
Certificate No. MD00/4611/0001/6a Expiry date: 15/09/2019
Sweden
SAPA PROFILER AB
Box 72
S-612 22 Finspång
Tel: +46 (0)122 795090
Email: [email protected]
Web:http://www.sapagroup.com
Certificate No. MD00/1270/0007/6a Expiry date: 20/03/2018
SAPA PROFILER AB
Refining & Semi Finished Al-Mg-Si grades
Sections
6082-T6
Bars
6082-T6
Gothenburg
30.00
30.00
Remelt / Press P2
Sjunnen Works SE-574 81
SE- 57481 Vetlanda
Tel: +46 (0) 70 34 94 695 Fax: +46 383 94467
Email: [email protected] Web: http://www.sapagroup.com
Certificate Number: MD00/3422/0006/6a Expiry date: 28/01/2020
Approval covers for semi finished products as vertically cast ingots up to 317mm diameter and nominal 7000mm length supplied in the homogenised condition.
Approval for sections does not include closed profile sections.
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
15
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Max Thickness/Diameter
(mm)
Office
Switzerland
ALU MENZIKEN EXTRUSION AG
Refining & Semi Finished 3003*
Extrusions
3003-O*
307.00
30.00
Dortmund
Hauptstrasse 35
CH-5737 Menziken
Tel: +41 62 765 29 07 Fax: +41 62 765 27 47
Email :[email protected]
Web: www.alu-menziken.com
Certificate No. MD00/3325/0003/6a Expiry date: 10/03/2016
CONSTELLIUM VALAIS SA
Refining & Semi Finished Al-Mg grades, Al-Si grades
Plates
5083-H321, 5086-H321
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5086-H112,
6061-T6, 6082-T6
Sections
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5086-H112
6005A-T6, 6061-T6, 6082-T6
Bars
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5086-H112
6061-T6, 6082-T6
Hamburg
8.00
150.00
600.00
720.00
600.00
720.00
PO Box
CH 3960 Sierre
Tel: +41 27 457 67 70
Email: [email protected]
Web: www.constellium.com
Certificate No. MD00/2608/0006/6a Expiry date: 03/08/2017
Taiwan, Republic of China
CHINA STEEL ALUMINIUM CORPORATION
Refining & Semi Finished 5083, 5086, 5383
Plates
5083-O, 5083-H111, 5083-H116,
5083-H112, 5083-H321, 5383-O,
5383-H111, 5383-H116, 5383-H321
5086-O, 5086-H111, 5086-H112,
5086-H116
Taipei
12.00
50.00
Kaohsiung
Tel: +886 7 871 8990 Fax: +886 7 872 1918
Email: [email protected]
Web page: www.csalu.com.tw
Certificate No. MD00/4526/0001/6a Expiry date: 10/11/2018
The Netherlands
NEDAL ALUMINIUM B.V.
Sections
Bars
6005A-T6, 6061-T6, 6082-T6
6005A-T6, 6061-T6, 6082-T6
50.00
50.00
Haren (Groningen)
8.00
Amsterdam
63.00
Newcastle upon Tyne
P.O. Box 2020
3500 GA Utrecht
Tel: +31 302925819 Mobile: +31 653516826 Email: [email protected]
Web: www.nedal.nl
Certificate No. MD00/3429/0004/6a Expiry date: 22/03/2018
SAPA PROFILES NL BV
Industrieweg 15,
3846 BB Harderwijk,
Postbus 30,
3846 Harderwijk.
Sections
6005A-T6, 6082-T6
Extrusions
6082-T6
Tel: +31 - 341 - 464411
Certificate No.
United Kingdom
SAPA PROFILES UK LTD
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
16
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Birtley Plant
Durham Road
Birtley
Chester-le-Street
County Durham, DH3 2AH
Category
Grades
Max Thickness/Diameter
(mm)
Office
Tel: +44 (0)191 301 1226
E-mail: [email protected]
Website: www.sapagroup.com
Certificate No. MD00/3832/0004/6a
Expiry date: 20/09/2019
SAPA PROFILES UK LTD.
Refining & Semi Finished Al-Mg-Si grades
Sections
6005A-T5, 6005A-T6, 6061-T5,
6061-T6, 6082-T5, 6082-T6
Bars
6005A-T5, 6005A-T6, 6061-T5,
6061-T6, 6082-T5, 6082-T6
Birmingham
25.00
75.00
Tibshelf Plant
Sawpit Lane
Tibshelf
Derbyshire DE55 5NH
Tel: +44 1773 549296
Email: [email protected]
Web: http://www.sapagroup.com
Certificate No. MD00/1261/0008/6a Expiry date: 07/09/2017
United States of America
A & B FOUNDRY AND MACHINING LLC.
835 N Main Street,
Franklin,
OH 45005,
Castings
Al-Si7Mg
1800.00
Chicago
Castings
Al-Si7Mg
0.03
Seattle
Al-Si7Mg
73.00
Vancouver BC
Tel: +1 937-412-1900 Fax: +1 937-412-2998
email: [email protected] web: www.abfoundry.com
Certificate No: MD00/4090/0002/6a Expiry Date: 07/11/2018
FREEMAN MARINE EQUIPMENT INC.
28366 Hunter Creek Road,
Gold Beach,
Oregon 97444
Tel: 1-888-FREEMAN, 1-888-373-3626, 1-541-247-7078 Fax: 1-541-2114
E-mail: [email protected]
Website: www.freemarine.com
Certificate No:
MD00/4631/0001/6a
Expiry Date: 20/11/2016
NU-CAST, INC.
29, Grenier Field Road,
Londonderry,
NH 03053
Castings
Tel No +1 603 432 1600
Fax No +1 603 432 0724
Email [email protected]
Web www. nu-cast.com
Certificate No MD00/ 3986/ 0002/6a
Expiry Date 07/02/2018
Page
© Lloyd’s Register Group Limited 2017. All rights reserved.
17
As at 23 May 2017
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective
officers, employees or agents are, individually and collectively, referred to in this
clause as ‘Lloyd's Register’. Lloyd's Register assumes no responsibility and shall
not be liable to any person for any loss, damage or expense caused by reliance on
the information or advice in this document or howsoever provided, unless that
person has signed a contract with the relevant Lloyd's Register entity for the
provision of this information or advice and in that case any responsibility or liability
is exclusively on the terms and conditions set out in that contract.
© Lloyd’s Register Group Limited 2017. All rights reserved.
© Lloyd’s Register Group Limited 2017. All rights reserved.