1 - 3 Ashley Park Drive, Chelsea Heights 3196
: (03) 8773 8773
P
F: (03) 9772 4999
E: [email protected]
www.melbournetrailers.com.au
MTCS Internal use
AUG2016
How to measure springs/spring order form
Eye & slipper spring
RECORD SPRING MEASUREMENTS AS FOLLOWS
Step 1. Measure along the edge of the main leaf following the curvature (i.e. follow the top leaf ) from the centre
of the eye (A) to the centre of the bolt hole (D).
Step 2. Repeat the same from the tail end of spring (B) to centre of the bolt hole (D).
Step 3. Measure (C to D) and give approximate camber.
A
B
C
D
PLEASE PROVIDE THE FOLLOWING MEASUREMENTS AS ACCURATELY AS POSSIBLE
1. Measurement of leaf (A - D) ________________2. Measurement of leaf (B - D)
________________
3. Camber of spring (C - D) ________________ 4. Width of spring
________________
5. Number of leaves
A
________________ B
7. Diameter of shackle pins ________________ 6. Steel thickness C
________________ 8. Grease type pins 9. Diameter of centre bolt ________________
Yes / No
D
Please Note:
1. All other leaves are measured the same as the main leaf
2. The main leaf is always No 1. or the longest leaf.
3. A - D and D - B follow the curve of the spring leaf.
4. Tandem spring assemblies centre bolt is usually off-set ( i.e Not in the centre of the spring )
For further assistance please contact Melbourne Trailer & Caravan Supplies
• Axle, Spring & Brake Spring Specialists • Australian Dexter Distributors • Large Range of Trailer Parts
1 - 3 Ashley Park Drive, Chelsea Heights 3196
: (03) 8773 8773
P
F: (03) 9772 4999
A
E: [email protected]
www.melbournetrailers.com.au
MTCS Internal use
B
C
How to measure springs/spring order form
RockerD roller spring
RECORD SPRING MEASUREMENTS AS FOLLOWS
Step 1. Measure along the edge of the main leaf following the curvature (i.e. follow the top leaf ) from the centre
of the eye (A) to the centre of the bolt hole (D).
Step 2. Repeat the same from the centre of the rear loop as indicated in the diagram below (B) to centre of the bolt hole (D).
Step 3. Measure (C to D) and give approximate camber.
A
B
C
D
GIVE THE FOLLOWING MEASUREMENTS AS ACCURATELY AS POSSIBLE
1. Measurement of leaf (A - D) ________________2. Measurement of leaf (B - D)
________________
3. Camber of spring (C - D) ________________ 4. Width of spring
________________
5. Number of leaves ________________ 6. Steel thickness ________________
7. Diameter of shackle pins ________________ 8. Grease type pins Yes / No
9. Diameter of centre bolt A
________________
C
B
Please Note:
1. All other leaves are measured the same as the Main leaf
D
2. The main leaf is always No 1. or the longest leaf.
3. A - D and D - B follow the curve of the spring leaf.
4. Tandem spring assemblies centre bolt is usually off-set ( i.e Not in the centre of the spring )
For further assistance please contact Melbourne Trailer & Caravan Supplies
• Axle, Spring & Brake Spring Specialists • Australian Dexter Distributors • Large Range of Trailer Parts
A
B
C
1 - 3 Ashley Park Drive, Chelsea Heights 3196
: (03) 8773 8773
P
F: (03) 9772 4999
E: [email protected]
www.melbournetrailers.com.au
MTCS Internal use
D
How to measure springs/spring order form
Eye & eye
RECORD SPRING MEASUREMENTS AS FOLLOWS
Step 1. Measure along the edge of the main leaf following the curvature (i.e. follow the top leaf ) from the centre
of the eye (A) to the centre of the bolt hole (D).
Step 2. Repeat the same from the tail end of spring (B) to the centre of the bolt hole (D).
Step 3. Measure (C to D) and give approximate camber.
A
B
C
D
GIVE THE FOLLOWING MEASUREMENTS AS ACCURATELY AS POSSIBLE
1. Measurement of leaf (A - D) ________________2. Measurement of leaf (B - D)
________________
3. Camber of spring (C - D) ________________ 4. Width of spring
________________
5. Number of leaves ________________ 6. Steel thickness ________________
7. Diameter of shackle pins ________________ 8. Grease type pins Yes / No
9. Diameter of centre bolt ________________
10. Front or rear spring ________________
For Tandem only
Please Note:
1. All other leaves are measured the same as the main leaf
2. The main leaf is always No 1. or the longest leaf.
3. A - D and D - B follow the curve of the spring leaf.
4. Tandem spring assemblies centre bolt is usually off-set ( i.e Not in the centre of the spring )
For further assistance please contact Melbourne Trailer & Caravan Supplies
• Axle, Spring & Brake Spring Specialists • Australian Dexter Distributors • Large Range of Trailer Parts