Parts Page Reorder No. PD09•57
Effective October, 2009
Wrenchless Pencil Grinder
With Turbine Brake and Hose Swivel
Air Tool Manual – Safety, Operation and Maintenance
SAVE THIS DOCUMENT, EDUCATE ALL PERSONNEL
Models:
60051 - 1/8" Collet, 60,000 RPM
60052 - 3/32" Collet, 35,000 RPM
FIND THE MOST CURRENT OFFERING OF SUPPORT DOCUMENTS AND ACCESSORIES @ WWW.DYNABRADE.COM
WARNING
Read and understand this tool manual before operating your air tool. Follow all safety rules for the protection of operating personnel
as well as adjacent areas. Always operate, inspect and maintain this tool in accordance with the American National Safety Institute
(ANSI) Safety Code for Portable Air Tools – B186.1. For additional safety information, refer to Safety Requirements for the Use, Care
and Protection of Abrasive Wheels – ANSI B7.1, Code of Federal Regulation – CFR 29 Part 1910, European Committee for Standards
(EN) Hand Held Non-Electric Power Tools – Safety Requirements and applicable State and Local Regulations.
SAFETY LEGEND
WARNING
WARNING
Practice safety requirements. Work alert,
have proper attire, and do not operate tools under
the influence of alcohol or drugs.
Read and understand tool manual before
work starts to reduce risk of injury to
operator, visitors, and tool.
WARNING
WARNING
Ear protection to be worn when exposure to sound,
exceeds the limits of applicable Federal, State or
local statues, ordinances and/or regulations.
Eye protection must be worn at all times,
eye protection to conform to ANSI Z87.1.
WARNING
WARNING
Respiratory protection to be used when exposed to
contaminates that exceed the applicable threshold
limit values required by law.
Air line hazard, pressurized supply lines and flexible
hoses can cause serious injury. Do not use damaged,
frayed or deteriorated air hoses and fittings.
WARNING
Some dust created by sanding, sawing, grinding, drilling, and other construction activities contain chemicals known to cause cancer,
birth defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
SAFETY INSTRUCTIONS
Carefully Read all instructions before operating or servicing any Dynabrade® Abrasive Power Tool.
Products offered by Dynabrade are not to be modified, converted or otherwise altered from the original design without expressed
written consent from Dynabrade, Inc.
Tool Intent: Pencil Grinder Tools are ideal for engraving, light deburring, deflashing, surface preparation, cleaning and finishing using the proper abrasive
stones, abrasive mounted wheels, points, molded abrasives, and carbide burrs.
Do not use tool for anything other than its intended applications.
This power tool is not intended for use in potentially explosive atmospheres and is not insulated against contact with electrical power.
Training: Proper care, maintenance, and storage of your tool will maximize performance.
• Employer's Responsibility – Provide Pencil Grinder operators with safety instructions and training for safe use of tools and accessories.
Accessory Selection:
• Abrasive/accessory RPM (speed) rating MUST be approved for AT LEAST the tool RPM rating.
(continued on next page)
SAFETY INSTRUCTIONS (Cont.)
•
•
•
•
Before mounting an accessory, visually inspect for defects. Do not use defective accessories.
Use only accessories of the correct mandrel size for the collet.
Follow tool specifications before choosing size and type of accessory.
Only use recommended fittings and air line sizes. Air supply hoses and air hose assemblies must have a minimum working pressure rating of 150 PSIG
(10 Bars, g) or 150 percent of the maximum pressure produced in the system, whichever is higher. (See tool Machine Specifications table.)
• If a mounted wheel is broken, a careful investigation should be made by the user to determine and correct the cause.
OPERATING INSTRUCTIONS
Warning: Always wear personal protection equipment. Operator of tool is responsible for following: accepted eye, face, respiratory, hearing and body protection.
Adjacent personnel must be protected from potential injury.
Warning: Be sure that any loose clothing, hair and all jewelry is properly restrained. Keep hand and clothing away from working end of the air tool.
Warning: Do Not use cut-off wheels or router bits.
Caution: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
MANDREL ACCESSORY MOUNTING INSTRUCTIONS
With Power Source Disconnected from the Tool, Mount Recommended Accessory
•
•
•
•
•
•
•
Check the collet insert to assure it is clean and in good condition.
Check the mandrel diameter of the accessory to insure it matches the collet insert size exactly. i.e. 1/8” shaft – 1/8” collet insert.
Rotate the lever 90 degrees to the housing to fully open the collet Insert.
Insert the mandrel of the accessory a minimum of 1 inch into the collet insert.
Adjust the collet by rotating the insert until mandrel slides freely but not loose inside the collet.
Rotate the lever parallel to the housing until it detents into place.
Insure the mounted accessory is properly secured in the collet by pulling on the accessory. Repeat steps above if the accessory is not properly secured.
Warning: Overhang (end of collet to abrasive) affects RPM rating and may create a hazard. Refer to the included ANSI B7.1 Table 27. Reference ANSI B7.1
for a more complete listing and additional information.
• Long mandrel accessories are subject to bending, whipping and breaking when run at high speeds.
Caution: After installing the accessory, before testing or using and/or after assembling tool, the Pencil Grinder must be started at a reduced speed to check
for good balance.
• Make sure no one is in the unguarded plane of the wheel.
• Gradually increase tool speed.
• DO NOT USE if tool vibration is excessive. Correct cause, and retest to insure safe operation.
• Run tool for one minute at operating speed in a protected area.
• BEFORE MOUNTING AN ACCESSORY, after all tool repairs and whenever a pencil grinder is issued for use, check tool RPM (speed) with tachometer
with air pressure set at 90 PSIG while the tool is running. If tool is operating at a higher speed than the RPM marked on the tool housing, or operating
improperly, the tool must be serviced and corrected before use.
Caution: Tool RPM must never exceed abrasive/accessory RPM rating. Check accessory manufacturer for details on maximum operating speed or special
mounting instructions.
• Make sure tool is off and connect power source. Do not expose air tool to inlet pressure above 90 PSIG or (6.2 Bars).
• Turn off inlet valve in case of an interruption of the energy supply.
• This tool should use filtered and regulated air, but does not require lubricated air. Lubricated air is not detrimental to tool life.
Caution: After installing the accessory, before testing or use and/or after assembling tool, the pencil grinder must be started at a reduced speed to check
for good balance. Make sure no one is in the unguarded plane of the wheel. Gradually increase tool speed. DO NOT USE if tool vibration is
excessive. Correct cause, and retest to insure safe operation. Run tool for 1 minute of operating speed in a protected area.
• Make sure that work area is uncluttered, and visitors are at a safe range from the tools and debris.
• Use a vise or clamping device to hold work piece firmly in place.
• Do not apply excessive force on tool or apply “rough” treatment to it.
• Always work with a firm footing, posture and proper lighting.
• Ensure that sparks and debris resulting from work do not create a hazard.
Warning: Sanding certain materials can create explosive dust. It is the employers responsibility to notify the user of acceptable dust levels. Reduce the risk
by using dust collection systems and personal protective equipment.
• Tools exhaust may contain bearing grease, and other materials. Direct exhaust away from operator.
• Use hearing protection when working with materials that produce high process noise levels. Permanent hearing loss can result from high sound levels.
• Do not set the tool down until the on/off valve is OFF and the tool has stopped turning.
• Always use dust extraction or suppression systems and personal protective equipment which are suitable for the materials being processed.
Report to your supervisor any condition of the tool, accessories, or operation you consider unsafe.
MAINTENANCE INSTRUCTIONS
Important: To keep tool safe a Preventative Maintenance Program is recommended for this tool. The program should include inspection of air supply lines,
air line pressure and repair of tools. Refer to ANSI B186.1 for additional maintenance information.
• Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model#, Serial# and RPM of your air tool.
• All Dynabrade Air Tools must be used with a Filter-Regulator to maintain all warranties.
Routine Preventative Maintenance:
• Check free speed of pencil grinder using a tachometer every 20 hours of use or weekly, whichever occurs more frequently.
• Take special care in assembly of speed control protective device - turbine.
• An Air Line Filter-Regulator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 10677 Air Line
Filter-Regulator – Provides accurate air pressure regulation, two-stage filtration of water contaminates. Operates 40 SCFM @ 90 PSIG has
3/8" NPT female ports.
• Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters,
ketones, chlorinated hydrocarbons or nitro carbons, or chemicals that have a low flash point (example: WD-40®).
2
MAINTENANCE INSTRUCTIONS - CONTINUED
Routine Preventative Maintenance:
• Air tool markings must be kept legible at all times. User is responsible for maintaining specification information i.e.: Model #, S/N, and RPM.
• Blow air supply hose out prior to initial use.
• Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.
• Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for safety information.
Handling and Storage:
• Use of tool rests, hangers and/or balancers is recommended.
• Protect tool inlet from debris.
• DO NOT carry tool by air hose.
• DO NOT force grinding swarf into the tool with compressed air; specifically avoid the front bearing areas.
• Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.
• Store accessories in protective racks or compartments to prevent damage.
Non-Lubricated Air System
Filter
Regulator
➤
90 PSIG
(6.2 Bar)
Air Flow
➤
Closed Loop Pipe System
(Sloped in the direction of air flow)
To Tool Station
Regulator
Refrigerated
Air Dryer
➤
➤
Filter
Ball
Valve
Drain
Valve
Drain
Valve
Air Hose
Air Flow
Air Compressor
and Receiver
PSIG @ Air Tool
• Ideally the air supply should be free from
moisture. To facilitate removing moisture
from air supply, the installation of a
refrigerated air dryer after the compressor
and the use of drain valves at each
tool station is recommended.
Ball
Valve
➤
• Dynabrade Air Power Tools are designed to
operate at 90 PSIG (6.2 Bar/620 kPa) maximum
air pressure at the tool inlet, when the tool is
running. Use recommended regulator to control
air pressure at each work station, if the supply
pressure is high.
➤
90 PSIG MAX
(6.2 Bar)
Drain Valve
Notice
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors can most often be
traced to an unclean air supply. Air pressure easily forces dirt or water contained in the air supply into motor bearings causing early failure. Dirt and water often score the inner
workings of the tool resulting in limited efficiency and power. Our warranty obligation is contingent upon proper use of our tools and cannot apply to equipment which has been
subjected to misuse such as unclean air, wet air or a lack of maintenance during the use of this tool.
Lifetime Warranty
All Dynabrade portable pneumatic power tools are rigorously inspected and performance tested in our factory before shipping to our customers. If a Dynabrade tool develops
a performance problem and an inherent defect is found during normal use and service, Dynabrade will warrant this tool against defects in workmanship and materials for
the lifetime of the tool. Upon examination and review at our factory, Dynabrade shall confirm that the tool qualifies for warranty status, and will repair or replace the tool at
no charge to the customer. Normally wearable parts and products are NOT covered under this warranty. Uncovered items include bearings, contact wheels, rotor blades,
regulators, valve stems, levers, shrouds, guards, O-rings, seals, gaskets and other wearable parts. Dynabrade’s warranty policy is contingent upon proper use of our tools
in accordance with factory recommendations, instructions and safety practices. It shall not apply to equipment that has been subjected to misuse, negligence, accident or
tampering in any way so as to affect its normal performance. To activate lifetime warranty, customer must register each tool at www.dynabrade.com. Dynabrade will not
honor lifetime warranty on unregistered tools. A one-year warranty will be honored on all unregistered portable pneumatic power tools. Lifetime warranty applies only to
portable pneumatic tools manufactured by Dynabrade, Inc. in the USA. Lifetime warranty applies only to the original tool owner; warranty is non-transferable.
3
Models:
60051, 60052
Wrenchless Pencil Grinder Complete Assembly
Index Key
No.
1/8" Insert
3/32" Insert
Bumper
Tactile Grip
Nose Piece
Washer
Spring
Seal Washer
Front Seal Washer
Outer Housing Seal
Inner Race Seal
Rear Seal Washer
Bearing
End Support
Spring Washer (20)
Spring Washer
Compressor
60091 Pin
60079 Collet Adjustment Screw
60064 Housing - 60051
60065 Housing - 60052
60095 Pin
60080 Cam Support
60082 Cam
60107 Screw
60101 Lock Nut
60083 Lever
60085 Spring
60084 Plunger
60096 Detent Guide
51661 Wave Washer
51651 Bearing
60068 Drive Shaft
60098 Pin
51656 Turbine Base
51678 Turbine
51675 Governor - 60,000RPM
51691 Governor - 35,000RPM
60069 Brake Plate
60099 Hex Nut
60103 Retaining Ring
60105 O-Ring
60075 Backing Plate
60072 Brake Assembly
51662 Bushing
60097 Spring
60104 O-Ring (2)
60100 Pin (2)
Turbine Cover
60110 35K - Red
60111 60K - Turquoise
10967 Bearing
10966 Swivel Barb
10972 O-Ring
10968 Bearing
95998 Retaining Ring
51276 Hose (24in.)
51665 On/Off Valve
95730 O-Ring (2)
51669 Retaining Ring
51282 Valve Body
51664 Valve Seat
51663 Tip Valve
51676 Spring
51271 Barb Fitting
51277 Hose (42 in.)
51269 Barb Fitting
56022 Inlet Screen
1 60076
60108
2 60077
3 60106
4 60066
5 60081
6 60102
7 60087
8 60088
9 60089
10 60090
11 60092
12 60093
13 60074
14 60073
15 60078
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
Detail A
Part # Description
6
8
9
7
11
5
1
2
3
4
5
7
10
8
10
9
6
23
22
Detail B
24
11
25
21
13
14
12
26
20
16
14
27
19
13
15
A8 T
17
4.5 N•m
18
T A7
8.5 N•m
32
28
29
30
34
31
33
37
39
41
38
44
40
42
43
A8
4.5 N•m
51
52
56
57
4
53
45 T
8.5 N•m
48
50
49
T
A8
59
60
61
62
58
53
54
35
47
46
36
55
KEY
A
Adhesive: A7 = Loctite #222
A8 = Loctite #567
T
Torque: N•m x 8.85 = In. - lbs.
Disassembly/Assembly Instructions - Wrenchless Pencil Grinder
Important: The Dynabrade Pneumatic Power Tool Lifetime Warranty Policy does NOT cover normally wearable parts and products. Before servicing this tool please contact
Dynabrade Inc. or a Dynabrade Subsidiary for information regarding the Dynabrade Pneumatic Power Tool Lifetime Warranty Policy.
Notice: Special repair tooling referred to in these instructions can be ordered from Dynabrade.
DISCONNECT AIR SUPPLY BEFORE ANY MAINTENANCE OR SERVICE.
Collet Disassembly/Assembly Instructions
To Disassemble:
1. Rotate Lever 60083 counterclockwise and open collet.
2. To loosen and remove the collet insert, turn it counterclockwise.
To Assemble:
1. To reduce accessory run-out and sticking; thoroughly clean, inspect, and polish as necessary, the 60076/60108 Collet Insert, and the collet body end of the drive shaft.
2. Install an accessory with the correct diameter shank into the collet insert. Turn the collet insert clockwise to secure the accessory in the collet. Note: Tighten the collet insert
around the shank of the accessory until a precise slip fit is established.
3. Rotate the 60083 Lever clockwise until it locks, securing the accessory in the collet.
Motor Disassembly/Assembly Instructions
To Disassemble:
1. To remove the 60110/60067 Swivel Cover, place an adjustable pin spanner wrench in the exhaust holes of the swivel cover and turn it counterclockwise. Note: Moderate
heat may be necessary to soften the thread sealant.
2. To remove the 60099 Hex Nut, insert a 4 mm hex key into the internal hex recess in the turbine end of the drive shaft. Hold it stationary with the hex key and use an
adjustable wrench to remove the hex nut. Turn it counterclockwise.
3. Remove the 60069 Brake Plate, 51691/51675 Governor, and the 51678 Turbine.
4. Remove the 60068 Drive Shaft from the housing.
5. Remove the 60098 Pin and the 51656 Turbine Base.
To Assemble:
1. Install the 51656 Turbine Base onto the drive shaft.
2. Press the 60098 Pin into the cross-drilled hole in the drive shaft. Centralize the pin in the drive shaft.
3. Install the 51678 Turbine, and the 51691/51675 Governor onto the drive shaft.
4. To install the 60069 Brake Plate, align the slot in the brake plate with the 60098 Pin, and the notches with the 51678 Turbine.
5. Apply a small amount of Loctite #222 (or equivalent) to the hex nut threads on the drive shaft. Tighten the 60099 Hex Nut onto the drive shaft.
(Torque to 4.5 N•m/40 in. lbs.)
6. Install the drive shaft assembly into the housing.
7. Apply a small amount of the Loctite #567 (or equivalent) to the threads of the 60110/60067 Swivel Cover. Install the swivel cover onto the housing and tighten.
(Torque to 8.5 N•m/75 in. lbs.)
Motor Disassembly/Assembly Complete.
Bearing Replacement Instructions
(Use only Dynabrade specified replacement bearings.)
To Remove:
1. (Follow Collet Disassembly Instructions)
2. To replace the 60093 Bearing, and the 51651 Bearing, remove the 60066 Nose Piece. Turn it counterclockwise. Note: The 60081 Washer, 60102 Spring, and 60087
Washer Seal can be removed with the nose piece.
3. Remove the 60077 Bumper. Turn it counterclockwise.
4. Important: Note the orientation of the following parts as they are removed. These parts must be installed in the same manner as they are removed. – Carefully remove the;
60088 Front Seal, 60089 Outer Housing Seal, 60090 Inner Race Seal, and 60092 Rear Seal.
5. Remove the; 60107 Screw, 60082 Cam, 60083 Lever, and 60080 Cam Support from the housing.
6. Use an adjustable pin spanner wrench in the exhaust holes of the 60110/60067 Swivel Cover to remove it from the housing. Note: Moderate heat may be necessary to
soften the thread sealant.
7. Carefully remove the drive shaft with turbine air motor, the 51661 Wave Washer, the 60074 End Support, and the twenty [20] 60073 Spring Washers from the housing.
8. Remove the 60093 Bearing from the housing.
9. Use the 96346 Bearing Separator, and the 96232 Arbor Press [#2] to remove the 51651 Bearing from the drive shaft.
To Install:
1. Use the arbor press and the raised inside diameter of the 96418 Bearing Press Tool to install the 51651 Bearing onto the drive shaft.
2. If the 60074 End Support and/or 60073 Spring Washers [20] (conical shaped spring washers) have been separated from the drive shaft, they should be installed onto the
drive shaft at this point. Orient the two end conical shaped spring washers with their large diameter against the end supports. The remainder of the conical shaped spring
washers should be installed small diameter to small diameter, and large diameter to large diameter in alternating fashion. (See Detail B)
Note: Do not nest the 60073 Spring Washers.
3. Install the 51661 Wave Washer into the housing, and install the drive shaft and bearing. Be careful not to lose the end support and spring washer stack-up. Note: The
51651 Bearing should be a slip fit into the bore of the housing. If it is not a slip-fit, use very fine abrasive cloth to polish the bearing bore.
4. Rest the 60099 Hex Nut on the tool plate of the 96232 Arbor Press [#2] with the collet body end of the drive shaft pointing up. Place the 60093 Bearing over the collet body
end of the drive shaft so that it drops into the housing. Use the raised outside diameter of the 96419 Bearing Press Tool to install the bearing into the housing.
5. Install the; 60092 Rear Seal Washer, 60090 Inner Race Seal, 60089 Outer Housing Seal, 60088 Front Seal Washer.
6. Install the 60077 Bumper until it bottoms.
7. Install the; 60081 Washer, 60102 Flat Wire Compression Spring, 60087 Seal Washer so that they are properly positioned in the 60066 Nose Piece. (See Detail A)
8. Apply a small amount of the Loctite #567 (or equivalent) to the threads of the housing.
9. Install the nose piece with parts onto the housing. (Torque to 4.5 N•m/40 in. lbs.)
10. Apply a small amount of the Loctite #243 (or equivalent) to the threads of the 60107 Screw and install the 60082 Cam and 60083 Lever onto the housing.
11. Install the 60076/60108 Collet Insert, into the collet body end of the drive shaft. Note: Adjust the collet as stated in Collet Assembly Steps #2 & 3.
Bearing Replacement Instructions Complete.
Air Bushing Replacement (The 51662 Air Bushing should be replaced every time the tool is serviced.)
1. To replace the 51662 Air Bushing, use an Easy Out Screw Extractor, or another means to remove it from the swivel cover.
2. Carefully press a new 51662 Air Bushing into the swivel cover. Leave approximately 1/16" (1.5 mm) standing above the edge of the swivel cover. Join the swivel cover to
the housing, turning the cover until it bottoms against the housing. Next back the cover off slightly until the drive shaft rotates freely. Carefully connect the tool to the air
supply and depress the “ON” button. As the tool is running slowly tighten the swivel cover to ‘wear-in’ the air bushing. Once the swivel cover is bottomed against the
housing and the tool is running freely, depress the “OFF” button, wait for the drive shaft to stop, and disconnect the tool from the air supply. – Remove the swivel cover
from the housing. Apply a small amount of the Loctite #567 (or equivalent) to the threads of the 60110/60067 Swivel Cover. Join and tighten the swivel cover to the
housing. (Torque to 8.5 N•m/75 in. lbs.)
3. Test the air motor for proper operation. Important: Always check RPM without an accessory mounted in the tool. Carefully connect the tool to the air supply. Activate the
“ON” button. Use a tachometer to check the speed (RPM) of the tool. The tool should operate within 10% of the rated maximum RPM that is marked on the housing. The
tool speed should not exceed the maximum RPM with operating air pressure set to 90 psig. (6.2 Bar) at the air inlet of the tool.
Brake Replacement
To Remove:
1. To remove the 60110/60067 Swivel Cover, place an adjustable pin spanner wrench in the exhaust holes of the swivel cover and turn it counterclockwise. Note: Moderate
heat may be necessary to soften the thread sealant.
2. Use external retaining ring pliers to remove the 60103 External Retaining Ring and the 60072 Brake Assembly.
3. Remove the 60075 Backing Plate from the bore of the 60072 Brake Assembly.
To Install:
1. Inspect all O-Ring seals and replace any that are damaged.
2. Make sure that the 60097 Compression Spring is in place. Lubricate the O-Ring seals with, 95842 Dynabrade Air Lube (10W/NR). Install the new 60072 Brake Assembly
with the notches aligned to engage the 60100 Pins (2).
3. Lubricate the O-Ring seals on the 60075 Backing Plate with 95842 Dynabrade Air Lube (10W/NR). Insert the backing plate into the bore of the 60072 Brake Assembly.
4. Use external retaining ring pliers to secure the 60075 Backing Plate with the 60103 External Retaining Ring. Make sure to engage the retaining ring groove in the swivel cover.
5. Apply a small amount of the Loctite #567 (or equivalent) to the threads of the 60110/60067 Swivel Cover. Join and tighten the swivel cover to the housing.
(Torque to 8.5 N•m/75 in. lbs.)
Hose Instructions (To repair or replace damaged hose):
To Remove:
1. Use a sharp utility knife to cut the hose length-wise, approximately 1" (25 mm) from the end of the tool or valve body. Remove the hose.
2. Trim away the damaged area of the hose, or replace the damaged hose with a new section of 51276 or 51277 Hose. Important: Use only Dynabrade Push-Lock Hose.
To Install:
3. Push the hose firmly onto the Push-Lock hose barb fitting. Push the hose all the way on, tight against the mating part.
Hose Repair/Replacement Complete.
Test the air motor for proper operation. Important: Always check RPM without an accessory mounted in the tool. – Carefully connect the tool to the air supply. Activate
the “ON” button. Use a tachometer to check the speed (RPM) of the tool. The tool should operate within 10% of the rated maximum RPM that is marked on the housing. The tool
speed should not exceed the maximum RPM with operating air pressure set to 90 psig. (6.2 Bar) at the air inlet of the tool.
Preventative Maintenance Schedule
For All Wrenchless Pencil Grinders
PART TYPE LEGEND
L
Easily lost. Care during
assembly/disassembly.
This service chart is published as a guide to expectant life of component parts. The replacement levels are
based on average tool usage over one year. Dynabrade Inc. considers one year usage to be 1,000 hours.
Index Part Description
#
Number
1
See Note Collet Insert
60077 Bumper
2
60106 Tactile Grip
3
60066 Nose Piece
4
60081 Washer
5
60102 Spring
6
60087 Seal Washer
7
60088 Front Seal Washer
8
60089 Outer Housing Seal
9
60090 Inner Race Seal
10
60092 Rear Seal Washer
11
60093 Bearing
12
60074 End Support
13
60073 Spring
14
60078 Spring Compressor
15
60079 Collet Adjustment Screw
16
17 See Note Housing
60091 Pin
18
60095 Pin
19
60080 Cam Support
20
60082 Cam
21
60107 Screw
22
60101 Lock Nut
23
60083 Lever
24
60085 Spring
25
60084 Plunger
26
60096 Detent Guide
27
51661 Wave Washer
28
51651 Bearing
29
60068 Drive Shaft
30
60098 Pin
31
Number
Required
1
1
1
1
1
1
1
1
1
1
1
1
1
20
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Part
Wear
30%
10%
10%
10%
10%
10%
10%
10%
10%
10%
10%
70%
10%
10%
10%
30%
10%
10%
10%
10%
30%
10%
10%
10%
10%
30%
10%
10%
70%
10%
10%
Part
Type
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
L
L
–
–
L
–
–
–
–
–
–
–
–
–
Index Part Description
#
Number
32
51656 Turbine Base
51678 Turbine
33
34 See Note Governor
60069 Brake Plate
35
60099 Hex Nut
36
60105 O-Ring
37
60075 Backing Plate
38
60072 Brake Assembly
39
51662 Bushing
40
60097 Spring
41
60103 Retaining Ring
42
43
60104 O-Ring
60100 Pin
44
45 See Note Swivel Cover
10967 Bearing
46
10966 Swivel Barb
47
10972 O-Ring
48
10968 Bearing
49
95998 Retaining Ring
50
51276 Hose (24in.)
51
51665 On/Off Valve
52
95730 O-Ring
53
54
51669 Retaining Ring
51282 Valve Body
55
51664 Valve Seat
56
51663 Tip Valve
57
51676 Spring
58
51271 Barb Fitting
59
51277 Hose (xxin.)
60
51269 Barb Fitting
61
56022 Inlet Screen
62
Note: Please refer to page 4 of tool manual for specific part number and description.
6
Number
Required
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
Part
Wear
10%
30%
30%
10%
10%
30%
10%
30%
100%
10%
70%
30%
10%
10%
30%
10%
10%
30%
70%
30%
10%
30%
70%
10%
10%
10%
10%
10%
30%
10%
30%
Part
Type
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Pencil Grinder Reference Tables
Note: Reprinted with permission of United Abrasives Manufacturers Association From (ANSI B7.1). For more information on other type mounted wheels refer
to (ANSI B7.1) Safety requirements for use, care and protection of Abrasive wheels.
7
Optional Accessories
FIND THE MOST CURRENT OFFERING OF SUPPORT DOCUMENTS AND ACCESSORIES @ WWW.DYNABRADE.COM
Model 10677: 55 SCFM @ 145 PSIG
3/8" or 1/2" NPT Female ports.
• Filter-Regulator, provides accurate air pressure
regulation and two stage filtration
of water/contaminates.
Model 93351
• 1/8" Carbide Burr Kit, Includes 12 burrs for
grinding, deburring, and finishing metal.
Special Repair Tools
96418 Bearing Press Tool
(.623" O.D., .375" I.D.)
Machine Specifications
Model
Motor
Sound
Maximum Air Flow
Air Pressure
Collet
Number
RPM
Level
SCFM (LPM)
PSIG (Bars)
Size
60051
60,000
77 dB(A)
8 (227)
90 (6.2)
1/8"
60052
35,000
65 dB(A)
8 (227)
90 (6.2)
3/32"
Additional Specifications: Air Inlet Thread 1/4" NPT • Hose Size 1/4" (6 mm)
Sound Level is the pressure measurement according to the method outlined in ISO regulation ISO-15744
Weight
Pound (kg)
1 (.45)
1 (.45)
Length
Inch (mm)
5-5/16 (136)
5-5/16 (136)
Height
Inch (mm)
1-1/2 (37)
1-1/2 (37)
Reference Contact Information
1. American National Standards Institute – ANSI
25 West 43rd Street
Forth Floor
New York, NY 10036
Tel: 1 (212) 642-4900
Fax: 1 (212) 398-0023
3. European Committee for Standardization
Rue de Stassart 36
B - 1050 Brussels, Belgium
2. Government Printing Office – GPO
Superintendent of Documents
Attn. New Orders
P.O. Box 371954
Pittsburgh, PA 15250-7954
Tel: 1 (202) 512-1803
®
Visit Our Web Site: www.dynabrade.com
Email: [email protected]
DYNABRADE
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1
© DYNABRADE, INC., 2009
PRINTED IN USA
PD09.57_10/09