VIA 2 PLUS
RECESSED
W W W . L U M E N W E R X . C O M
DESCRIPTION
Via 2 PLUS combines the elegance of Via 2 with
PROJECT: __________________________________
the added architectural element of a lens which
____________________________________________
protrudes ½" below the surface plane. Via 2 PLUS
TYPE: ______________________________________
is available as individual or continuous recessed
NOTES: ____________________________________
runs for both drywall and grid ceilings. See
separate spec sheets for, LED and other available
____________________________________________
mountings.
Grid - shown with HLO optics
Drywall - shown with HLO optics
ORDER GUIDE
VIA2+R
HLO
LUMINAIRE ID
OPTICS
LIGHT SOURCE
NUMBER OF LAMPS
LUMINAIRE LENGTH
VOLTAGE
BALLAST
VIA2+R - via 2" drop lens recessed
HLO - High-Efficiency Lambertian Optic
T5 - T5 lamp
1S - 1 staggered
Standard sections - 2', 3', 4', 5', 8' & 12'
120 - 120V
IN - instant start
For all other specify length
277 - 277V
RS - rapid start
#FT - nominal length in feet
UNV - 120V-277V
D - dimming 0-10V
#IN - length in inches
347 - 347V
ST - step dimming
T5HO - T5HO lamp
Continuous Run - for luminaires over 12'
DA - dali
Minimum Individual section 2'
LHL - Lutron Hi-Lume A
ELECTRICAL
MOUNTING
FINISH
CONTROLS
OPTIONS
1 - 1 circuit
TG9 - tegular 9/16"
W - matte white
WIRELESS
FU - fuse
+#EB - emergency battery pack (for min 4' fixture)
TG15 - tegular 15/16"
CF# - custom finish specify RAL#
EWC - EnOcean Wireless Controller
FWC - flexible whip cable (6' std)
+#EM - emergency light circuit
TB9 - t-bar 9/16"
LMC - Lutron Motion Controller
CP - Chicago Plenum
+#NL - night light circuit
TB15 - t-bar 15/16"
LDC - Daylight Controller
CU - custom
+GTD - generator transfer device
ST - screw slot t-bar
DTR - drywall trim
DTL - drywall trimless
DMF - drywall mud flange
OHC - other ceiling (specify)
CROSS SECTION
See page 2 for ordering code detailed information
OPTICS
3 3/4"
1/2"
2 3/8"
VIA2PLUSR - recessed
HLO - High-efficiency Lambertian Optic
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
File Name: VIA2_PLUS.FLU.RECESSED.SPEC
LumenWerx ULC. reserves the right to change or modify product specifications without notification
February 9, 2015
Page: 1 / 3
VIA 2 PLUS
RECESSED
W W W . L U M E N W E R X . C O M
OPTICS
MOUNTING OPTIONS
HIGH EFFICIENCY LAMBERTIAN OPTIC (HLO) - matte white side reflectors combined with
Recess mount into exposed or concealed T-Bar or Tegular grid ceiling
High-Efficiency Lambertian Optic (HLO) shielding of diffusing 0.075" thick acrylic with up to 88%
Mounting for drywall ceilings are available with visible trim, mud flange trim or trimless
transmission and good source obscuration. Luminaire brightness is controlled by the flux-toshielding area ratio.
LUMINAIRE LENGTH
Via 2 PLUS is made up of standard 2, 3, 4, 5, 8 and 12 foot sections that may be joined together to
create longer continuous run lengths. Exact run length must be noted in the product code. The
minimum individual section available is 2 foot.
All individual sections are joined together onsite using the joiner kits provided. LumenWerx offers
joiner kits that are extremely simple to work with in the field and result in a fixture that appears
3 3/16"
3 3/8"
between T-bars
3 3/16"
3 3/8"
between T-bars
TG15 - tegular 15/16"
TB9 - t-bar 9/16"
3 3/16"
3 3/8"
between T-bars
TG9 - tegular 9/16"
2 3/8"
virtually seamless with no light leak at any connection.
Joining system
3 3/4"
TB15 - t-bar 15/16"
ST - screw slot t-bar
2 3/8"
t-bar
1/2"
3 1/8"
hole width
4 7/8"
with flanges
3 3/16"
3 3/8"
between T-bars
3 3/16"
3 3/8"
between T-bars
DMF - drywall mud flange
2 3/8"
Mud flange
4 5/8"
3 3/4"
3 3/4"
ELECTRICAL
Universal input voltages with multiple control schemes offered. Consult factory for availability.
2 7/8"
hole width
3 3/16"
with flanges
EMERGENCY
Factory installed long life high temperature recyclable Ni-Cad battery pack with test switch and
charge indicator, minimum of 90 minutes operation. Recharge time of 24 hours.
1/2"
DTR - drywall trim
1/2"
2 1/2"
hole width
DTL - drywall trimless
FINISH
Interior - 95%, reflective matte powder coated white paint
Exterior - matte white or silver powder coating.
Custom finishes are also available.
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
File Name: VIA2_PLUS.FLU.RECESSED.SPEC
LumenWerx ULC. reserves the right to change or modify product specifications without notification
February 9, 2015
Page: 2 / 3
VIA 2 PLUS
RECESSED
W W W . L U M E N W E R X . C O M
CONTROLS
LumenWerx offers several options for integrating motion and daylight controls into Via 2 PLUS
luminaires. Wireless options incorporate a wireless controller/powerpack into the luminaire,
which receives signals from a wireless sensor (by others) installed in the space. The advantages
of the wireless option include greater flexibility of control options, sensor coverage and system
integration.
Wireless
EnOcean Wireless Controller (EWC) provides both a power pack for presence detection control
and a 0-10V interface for daylight harvesting. EnOcean wireless sensors (by others) mounted in the
room signal the onboard EWC. This option permits manual on/automatic off (vacancy) control.
Lutron Motion Controller (LMC) and Daylight Controller (LDC) provide inputs to Ecosystem
drivers. Compatible Lutron wireless motion and daylight sensors (by others) mounted in the room
signal onboard LPC or LDC. This option permits manual on/automatic off (vacancy) control.
CONSTRUCTION
Housing - Extruded Aluminum (0.095" nominal) up to 90% Recycled Content
Interior brackets - Die formed cold rolled sheet steel 18 gauge thick
Joining system - Die cast Zinc (0.95" nominal) and die Formed galvanized sheet 18 gauge
Reflectors - Extruded Aluminum (0.075” nominal) up to 95% reflective matte
Mud flange - Extruded Aluminum (0.075" nominal) up to 90% Recycled Content
Slip-through bracket - Die Formed galvanized sheet 18 gauge
End plate - Die formed cold rolled sheet steel 18 gauge thick
WEIGHT
Via 2 4ft - 9.03lbs - 4.1kg
Via 2 8ft - 18.28lbs - 8.3kg
Via 2 12ft - 27.97lbs - 12.7kg
CERTIFICATIONS
ETL - Rated for Dry/Damp locations. Conforms to UL Standard 1598 and certified to CAN/CSA
Standard C22.2 No. 250.0.
Chicago plenum - City of Chicago Approved (CCEA)
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
File Name: VIA2_PLUS.FLU.RECESSED.SPEC
LumenWerx ULC. reserves the right to change or modify product specifications without notification
February 9, 2015
Page: 3 / 3
VIA 2 PLUS
RECESSED VERTICAL
W W W . L U M E N W E R X . C O M
DESCRIPTION
Via 2 PLUS combines the elegance of Via 2 with
PROJECT: __________________________________
the added architectural element of a lens which
____________________________________________
protrudes ½" below the surface plane. Via 2 PLUS is
TYPE: ______________________________________
available as individual or continuous recessed runs
NOTES: ____________________________________
for both drywall and grid ceilings. See separate spec
____________________________________________
sheets for, LED and other available mountings.
Flush - shown with HLO optics
ORDER GUIDE
VIA2+RV
HLO
LUMINAIRE ID
OPTICS
LIGHT SOURCE
NUMBER OF LAMPS
LUMINAIRE LENGTH
VOLTAGE
BALLAST
VIA2+RV - via 2" drop lens recessed
HLO - High-Efficiency Lambertian Optic
T5 - T5 lamp
1S - 1 staggered
Standard sections - 2', 3', 4', 5', 8' & 12'
120 - 120V
IN - instant start
For all other specify length
277 - 277V
RS - rapid start
#FT - nominal length in feet
UNV - 120V-277V
D - dimming 0-10V
#IN - length in inches
347 - 347V
ST - step dimming
T5HO - T5HO lamp
vertical
Continuous Run - for luminaires over 12'
DA - dali
Minimum Individual section 2'
LHL - Lutron Hi-Lume A
ELECTRICAL
MOUNTING
FINISH
CONTROLS
OPTIONS
1 - 1 circuit
DTR - drywall trim
W - matte white
WIRELESS
FU - fuse
+#EB - emergency battery pack (for min 4' fixture)
DTL - drywall trimless
CF# - custom finish specify RAL#
EWC - EnOcean Wireless Controller
FWC - flexible whip cable (6' std)
+#EM - emergency light circuit
DMF - drywall mud flange
LMC - Lutron Motion Controller
CP - Chicago Plenum
+#NL - night light circuit
OHW - other wall (specify)
LDC - Daylight Controller
CU - custom
+GTD - generator transfer device
See page 2 for ordering code detailed information
CROSS SECTION
2 1/2"
hole
width
1/2"
OPTICS
2 3/8"
3 3/4"
VIA2PLUSRV - recessed vertical
HLO - High-efficiency Lambertian Optic
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
File Name: VIA2_PLUS.FLU.RECESSED.VERTICAL.SPEC
LumenWerx ULC. reserves the right to change or modify product specifications without notification
February 9, 2015
Page: 1 / 3
VIA 2 PLUS
RECESSED VERTICAL
W W W . L U M E N W E R X . C O M
OPTICS
MOUNTING OPTIONS
HIGH EFFICIENCY LAMBERTIAN OPTIC (HLO) - matte white side reflectors combined with
Recessed Wall Mounting for drywall is available with visible trim, mud flange trim or
High-Efficiency Lambertian Optic (HLO) shielding of diffusing 0.075" thick acrylic with up to 88%
trimless
transmission and good source obscuration. Luminaire brightness is controlled by the flux-toshielding area ratio.
LUMINAIRE LENGTH
3 3/16"
with
flanges
Via 2 PLUS is made up of standard 2, 3, 4, 5, 8 and 12
2 7/8"
hole
width
foot sections that may be joined together to create
1/2"
longer continuous run lengths. Exact run length must
2 3/8"
3 3/4"
2 1/2"
hole
width
3 3/4"
1/2"
DTR - drywall trim
be noted in the product code. The minimum individual
2 3/8"
DTL - drywall trimless
section available is 2 foot.
All individual sections are joined together onsite using
the joiner kits provided. LumenWerx offers joiner kits
that are extremely simple to work with in the field and
4 7/8" 3 1/8"
with
hole
flanges width
result in a fixture that appears virtually seamless with
no light leak at any connection.
joining system for Via 2 PLUS
1/2"
2 3/8"
3 3/4"
DMF - drywall mud flange
ELECTRICAL
Universal input voltages with multiple control schemes offered. Consult factory for availability.
FINISH
Interior - 95%, reflective matte powder coated white paint
EMERGENCY
Exterior - matte white or silver powder coating.
Factory installed long life high temperature recyclable Ni-Cad battery pack with test switch and
Custom finishes are also available.
charge indicator, minimum of 90 minutes operation. Recharge time of 24 hours.
CONTROLS
LumenWerx offers several options for integrating motion and daylight controls into
Via 2 PLUS luminaires. Wireless options incorporate a wireless controller/powerpack
into the luminaire, which receives signals from a wireless sensor (by others) installed
in the space. The advantages of the wireless option include greater flexibility of control
options, sensor coverage and system integration.
Wireless
EnOcean Wireless Controller (EWC) provides both a power pack for presence
detection control and a 0-10V interface for daylight harvesting. EnOcean wireless
sensors (by others) mounted in the room signal the onboard EWC. This option permits
manual on/automatic off (vacancy) control.
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
File Name: VIA2_PLUS.FLU.RECESSED.VERTICAL.SPEC
LumenWerx ULC. reserves the right to change or modify product specifications without notification
February 9, 2015
Page: 2 / 3
VIA 2 PLUS
RECESSED VERTICAL
W W W . L U M E N W E R X . C O M
Lutron Motion Controller (LMC) and Daylight Controller (LDC) provide inputs to Ecosystem
drivers. Compatible Lutron wireless motion and daylight sensors (by others) mounted in the room
signal onboard LPC or LDC. This option permits manual on/automatic off (vacancy) control.
CONSTRUCTION
Housing - Extruded Aluminum (0.095" nominal) up to 90% Recycled Content
Interior brackets - Die formed cold rolled sheet steel 18 gauge thick
Joining system - Die cast Zinc (0.95" nominal) and die Formed galvanized sheet 18 gauge
Reflectors - Extruded Aluminum (0.075” nominal) up to 95% reflective matte
End plate - Die formed cold rolled sheet steel 18 gauge thick
WEIGHT
Via 2 4ft - 9.03lbs - 4.1kg
Via 2 8ft - 18.28lbs - 8.3kg
Via 2 12ft - 27.97lbs - 12.7kg
CERTIFICATIONS
ETL - Rated for Dry/Damp locations. Conforms to UL Standard 1598 and certified to CAN/CSA
Standard C22.2 No. 250.0.
Chicago plenum - City of Chicago Approved (CCEA)
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
File Name: VIA2_PLUS.FLU.RECESSED.VERTICAL.SPEC
LumenWerx ULC. reserves the right to change or modify product specifications without notification
February 9, 2015
Page: 3 / 3
VIA 2 PLUS LED
RECESSED
W W W . L U M E N W E R X . C O M
DESCRIPTION
Via 2 PLUS combines the
PROJECT: __________________________________
elegance of Via 2 with the added architectural
____________________________________________
element of a lens which protrudes ½" below the
TYPE: ______________________________________
surface plane. Via 2 PLUS is available as individual
NOTES: ____________________________________
or continuous recessed runs for both drywall and
grid ceilings.
Grid - shown with HLO optics
____________________________________________
Drywall - shown with HLO optics
ORDER GUIDE
VIA2+R
HLO
LUMINAIRE ID
OPTICS
LIGHT SOURCE
CRI
LUMEN PACKAGES
COLOR TEMP.
VIA2+R - via 2" drop lens recessed
HLO - High-Efficiency Lambertian Optic
LED - high performance LED
80 - 80CRI
400 - low output 400lm/f
30 - 3000k
T5/T5HO - T5/T5HO lamp (consult factory)
90 - 90CRI (consult factory)
500 - med. output 500lm/f
35 - 3500k
750 - high output 750lm/f
40 - 4000k
LUMINAIRE LENGTH
VOLTAGE
DRIVER
ELECTRICAL
MOUNTING
FINISH
CONTROLS
Standard sections - 2', 3', 4', 5', 8' & 12'
120 - 120V
D - dimming 0-10V
1 - 1 circuit
TG9 - tegular 9/16"
W - matte white
WIRELESS
For all other specify length
277 - 277V
DA - Dali
+#EB - emergency battery pack
TG15 - tegular 15/16"
CF# - custom finish specify RAL#
EWC - EnOcean Wireless Controller
#FT - nominal length in feet
UNV - 120V-277V
LHL# - Lutron Hi-Lume A
(for min 4' fixture)
TB9 - t-bar 9/16"
LMC - Lutron Motion Controller
#IN - length in inches
347 - 347V
LEH - Lutron EcoSystem H
+#EM - emergency light circuit
TB15 - t-bar 15/16"
LDC - Daylight Controller
Continuous Run - for luminaires over 12'
LE5 - Lutron EcoSystem 5
+#NL - night light circuit
ST - screw slot t-bar
Minimum Individual section 2'
OTH - other (consult factory)
+GTD - generator transfer device
DTR - drywall trim
DTL - drywall trimless
DMF - drywall mud flange
OHC - other ceiling (specify)
CROSS SECTION
See page 2 for ordering code detailed information
OPTICS
OPTIONS
FU - fuse
FWC - flexible whip cable (6' std)
CP - Chicago Plenum
CU - custom
3 3/4"
1/2"
2 3/8"
VIA2PLUSR - recessed
HLO - High-efficiency Lambertian Optic
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
File Name: VIA2_PLUS.RECESSED.SPEC
LumenWerx ULC. reserves the right to change or modify product specifications without notification
February 20, 2015
Page: 1 / 3
VIA 2 PLUS LED
RECESSED
W W W . L U M E N W E R X . C O M
OPTICS
ELECTRICAL
HIGH EFFICIENCY LAMBERTIAN OPTIC (HLO) - matte white side reflectors combined with
Factory-set adjustable output current electronic driver with 120-277V AC line input.
High-Efficiency Lambertian Optic (HLO) shielding of diffusing 0.075" thick acrylic with up to 88%
Dimmable from at least 100%-5% with 0-10V control. Rated life (90% survivorship)
transmission and good source obscuration. Luminaire brightness is controlled by the flux-to-
of 50,000 hours at 50ºC max. ambient (and 70ºC max. case) temperature. Terminal
shielding area ratio.
block connections for easy service. At maximum driver load: Efficiency>84%, PF>0.9,
THD<20%. Other specifiable options include Lutron Hi-Lume A (specify 2, 3 or 4 wires),
LIGHT SOURCE - LED
EcoSystem H (100%-1%, fade-to-black) and EcoSystem 5 (100%-5%) dimmable drivers
Custom linear array of mid-flux LED's are cartridge-mounted with quick-connect wiring to facilitate
and DALI protocol drivers.
service and thermal management. Available in 3000K, 3500K and 4000K with a minimum 80 CRI
and an option for 90 CRI with elevated R9 value. Color consistency maintained to within 3 SDCM.
EMERGENCY
LEDs operated at reduced drive current to optimize efficacy and lumen maintenance.
Factory installed long life high temperature recyclable Ni-Cad battery pack with test
All LEDs have been tested in accordance with IESNA LM-80-08 and the results have shown L80
switch and charge indicator, minimum of 90 minutes operation, up to 1300 lumens
lumen maintenance greater than 60,000 hours. Absolute product photometry is measured and
(25ºC) emergency lighting output. Recharge time of 24 hours.
presented in accordance with IESNA LM-79, unless otherwise indicated.
MOUNTING OPTIONS
PERFORMANCE PER 4' AT 4000K
LED output
Color Temp
Watts
Nominal Lumens
Efficacy
Lumens Per Watt
low output
4000K
17
1600
91
medium output
4000K
22
2000
92
ultra high ouput
4000K
33
3000
90
LUMINAIRE LENGTH
Via 2 PLUS is made up of standard 2, 3, 4, 5, 8 and 12 foot sections that may be joined together to
create longer continuous run lengths. Exact run length must be noted in the product code. The
minimum individual section available is 2 foot.
Recess mount into exposed or concealed T-Bar or Tegular grid ceiling
Mounting for drywall ceilings are available with visible trim, mud flange trim or trimless
3 3/16"
3 3/8"
between T-bars
TG9 - tegular 9/16"
3 3/16"
3 3/8"
between T-bars
3 3/16"
3 3/8"
between T-bars
TG15 - tegular 15/16"
TB9 - t-bar 9/16"
2 3/8"
All individual sections are joined together onsite using the joiner kits provided. LumenWerx offers
joiner kits that are extremely simple to work with in the field and result in a fixture that appears
virtually seamless with no light leak at any connection.
3 3/4"
Joining system
3 3/16"
3 3/8"
between T-bars
TB15 - t-bar 15/16"
t-bar
3 3/16"
3 3/8"
between T-bars
ST - screw slot t-bar
1/2"
3 1/8"
hole width
4 7/8"
with flanges
DMF - drywall mud flange
Mud flange
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
File Name: VIA2_PLUS.RECESSED.SPEC
LumenWerx ULC. reserves the right to change or modify product specifications without notification
February 20, 2015
Page: 2 / 3
VIA 2 PLUS LED
2 3/8"
RECESSED
W W W . L U M E N W E R X . C O M
WEIGHT
2 3/8"
Via 2 4ft - 9.03lbs - 4.1kg
Via 2 8ft - 18.28lbs - 8.3kg
Via 2 12ft - 27.97lbs - 12.7kg
4 5/8"
3 3/4"
3 3/4"
CERTIFICATIONS
2 7/8"
hole width
3 3/16"
with flanges
1/2"
DTR - drywall trim
1/2"
2 1/2"
hole width
ETL - Rated for Dry/Damp locations. Conforms to UL Standard 1598 and certified to
CAN/CSA Standard C22.2 No. 250.0.
Chicago plenum - City of Chicago Approved (CCEA)
DTL - drywall trimless
WARRANTY
LumenWerx provides a five-year limited warranty of electrical and mechanical
FINISH
Interior - 95%, reflective matte powder coated white paint
Exterior - matte white or silver powder coating.
performance of the luminaires, including the LED boards, drivers, and auxiliary
electronics. LumenWerx will repair or replace defective luminaires or components at
our discretion, provided they have been installed and operated in accordance with our
Custom finishes are also available.
specifications. Other limitations apply, please refer to the full warranty on our website.
CONTROLS
LumenWerx offers several options for integrating motion and daylight controls into Via 2 PLUS
luminaires. Wireless options incorporate a wireless controller/powerpack into the luminaire,
which receives signals from a wireless sensor (by others) installed in the space. The advantages
of the wireless option include greater flexibility of control options, sensor coverage and system
integration.
Wireless
EnOcean Wireless Controller (EWC) provides both a power pack for presence detection control
and a 0-10V interface for daylight harvesting. EnOcean wireless sensors (by others) mounted in the
room signal the onboard EWC. This option permits manual on/automatic off (vacancy) control.
Lutron Motion Controller (LMC) and Daylight Controller (LDC) provide inputs to Ecosystem
drivers. Compatible Lutron wireless motion and daylight sensors (by others) mounted in the room
signal onboard LPC or LDC. This option permits manual on/automatic off (vacancy) control.
CONSTRUCTION
Housing - Extruded Aluminum (0.095" nominal) up to 90% Recycled Content
Interior brackets - Die formed cold rolled sheet steel 18 gauge thick
Joining system - Die cast Zinc (0.95" nominal) and die Formed galvanized sheet 18 gauge
Reflectors - Extruded Aluminum (0.075” nominal) up to 95% reflective matte
Mud flange - Extruded Aluminum (0.075" nominal) up to 90% Recycled Content
Slip-through bracket - Die Formed galvanized sheet 18 gauge
End plate - Die formed cold rolled sheet steel 18 gauge thick
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
File Name: VIA2_PLUS.RECESSED.SPEC
LumenWerx ULC. reserves the right to change or modify product specifications without notification
February 20, 2015
Page: 3 / 3
VIA 2 PLUS LED
RECESSED VERTICAL
W W W . L U M E N W E R X . C O M
DESCRIPTION
Via 2 PLUS combines the elegance of Via 2 with
PROJECT: __________________________________
the added architectural element of a lens which
____________________________________________
protrudes ½" below the surface plane. Via 2 PLUS is
TYPE: ______________________________________
available as individual or continuous recessed runs
NOTES: ____________________________________
for both drywall and grid ceilings.
____________________________________________
Flush - shown with HLO optics
ORDER GUIDE
VIA2+RV
HLO
LUMINAIRE ID
OPTICS
LIGHT SOURCE
CRI
LUMEN PACKAGES
COLOR TEMP.
VIA2+RV - via 2" drop lens recessed vertical
HLO - High-Efficiency Lambertian Optic
LED - high performance LED
80 - 80CRI
400 - low output 400lm/f
30 - 3000k
T5/T5HO - T5/T5HO lamp (consult factory)
90 - 90CRI (consult factory)
500 - med. output 500lm/f
35 - 3500k
750 - high output 750lm/f
40 - 4000k
LUMINAIRE LENGTH
VOLTAGE
DRIVER
ELECTRICAL
MOUNTING
FINISH
CONTROLS
Standard sections - 2', 3', 4', 5', 8' & 12'
120 - 120V
D - dimming 0-10V
1 - 1 circuit
DTR - drywall trim
W - matte white
WIRELESS
For all other specify length
277 - 277V
DA - Dali
+#EB - emergency battery pack
DTL - drywall trimless
CF# - custom finish specify RAL#
EWC - EnOcean Wireless Controller
#FT - nominal length in feet
UNV - 120V-277V
LHL# - Lutron Hi-Lume A
(for min 4' fixture)
DMF - drywall mud flange
LMC - Lutron Motion Controller
#IN - length in inches
347 - 347V
LEH - Lutron EcoSystem H
+#EM - emergency light circuit
OHW - other wall (specify)
LDC - Daylight Controller
Continuous Run - for luminaires over 12'
LE5 - Lutron EcoSystem 5
+#NL - night light circuit
Minimum Individual section 2'
OTH - other (consult factory)
+GTD - generator transfer device
See page 2 for ordering code detailed information
OPTIONS
FU - fuse
CROSS SECTION
OPTICS
FWC - flexible whip cable (6' std)
CP - Chicago Plenum
CU - custom
2 1/2"
hole
width
1/2"
2 3/8"
3 3/4"
VIA2PLUSRV - recessed vertical
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
HLO - High-efficiency Lambertian Optic
File Name: VIA2_PLUS.RECESSED.VERTICAL.SPEC
LumenWerx ULC. reserves the right to change or modify product specifications without notification
February 20, 2015
Page: 1 / 3
VIA 2 PLUS LED
RECESSED VERTICAL
W W W . L U M E N W E R X . C O M
OPTICS
ELECTRICAL
HIGH EFFICIENCY LAMBERTIAN OPTIC (HLO) - matte white side reflectors combined with
Factory-set adjustable output current electronic driver with 120-277V AC line input.
High-Efficiency Lambertian Optic (HLO) shielding of diffusing 0.075" thick acrylic with up to 88%
Dimmable from at least 100%-5% with 0-10V control. Rated life (90% survivorship)
transmission and good source obscuration. Luminaire brightness is controlled by the flux-to-
of 50,000 hours at 50ºC max. ambient (and 70ºC max. case) temperature. Terminal
shielding area ratio.
block connections for easy service. At maximum driver load: Efficiency>84%, PF>0.9,
THD<20%. Other specifiable options include Lutron Hi-Lume A (specify 2, 3 or 4 wires),
LIGHT SOURCE - LED
EcoSystem H (100%-1%, fade-to-black) and EcoSystem 5 (100%-5%) dimmable drivers
Custom linear array of mid-flux LED's are cartridge-mounted with quick-connect wiring to facilitate
and DALI protocol drivers.
service and thermal management. Available in 3000K, 3500K and 4000K with a minimum 80 CRI
and an option for 90 CRI with elevated R9 value. Color consistency maintained to within 3 SDCM.
EMERGENCY
LEDs operated at reduced drive current to optimize efficacy and lumen maintenance.
Factory installed long life high temperature recyclable Ni-Cad battery pack with test
All LEDs have been tested in accordance with IESNA LM-80-08 and the results have shown L80
switch and charge indicator, minimum of 90 minutes operation, up to 1300 lumens
lumen maintenance greater than 60,000 hours. Absolute product photometry is measured and
(25ºC) emergency lighting output. Recharge time of 24 hours.
presented in accordance with IESNA LM-79, unless otherwise indicated.
MOUNTING OPTIONS
PERFORMANCE PER 4' AT 4000K
LED output
Color Temp
Watts
Nominal Lumens
Efficacy
Lumens Per Watt
low output
4000K
17
1600
91
medium output
4000K
22
2000
92
ultra high ouput
4000K
33
3000
90
Recessed Wall Mounting for drywall is available with visible trim, mud flange trim or
trimless
3 3/16"
with
flanges
2 7/8"
hole
width
LUMINAIRE LENGTH
1/2"
Via 2 PLUS is made up of standard 2, 3, 4, 5, 8 and 12
2 3/8"
3 3/4"
2 3/8"
3 3/4"
1/2"
DTR - drywall trim
foot sections that may be joined together to create
2 1/2"
hole
width
DTL - drywall trimless
longer continuous run lengths. Exact run length must
be noted in the product code. The minimum individual
section available is 2 foot.
All individual sections are joined together onsite using
4 7/8" 3 1/8"
with
hole
flanges width
the joiner kits provided. LumenWerx offers joiner kits
that are extremely simple to work with in the field and
1/2"
2 3/8"
3 3/4"
result in a fixture that appears virtually seamless with
no light leak at any connection.
joining system for Via 2 PLUS
DMF - drywall mud flange
FINISH
Interior - 95%, reflective matte powder coated white paint
Exterior - matte white or silver powder coating.
Custom finishes are also available.
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
File Name: VIA2_PLUS.RECESSED.VERTICAL.SPEC
LumenWerx ULC. reserves the right to change or modify product specifications without notification
February 20, 2015
Page: 2 / 3
VIA 2 PLUS LED
RECESSED VERTICAL
W W W . L U M E N W E R X . C O M
CONTROLS
LumenWerx offers several options for integrating motion and daylight controls into Via 2 PLUS
luminaires. Wireless options incorporate a wireless controller/powerpack into the luminaire,
which receives signals from a wireless sensor (by others) installed in the space. The advantages
of the wireless option include greater flexibility of control options, sensor coverage and system
integration.
Wireless
EnOcean Wireless Controller (EWC) provides both a power pack for presence detection control
and a 0-10V interface for daylight harvesting. EnOcean wireless sensors (by others) mounted in the
room signal the onboard EWC. This option permits manual on/automatic off (vacancy) control.
Lutron Motion Controller (LMC) and Daylight Controller (LDC) provide inputs to Ecosystem
drivers. Compatible Lutron wireless motion and daylight sensors (by others) mounted in the room
signal onboard LPC or LDC. This option permits manual on/automatic off (vacancy) control.
CONSTRUCTION
Housing - Extruded Aluminum (0.095" nominal) up to 90% Recycled Content
Interior brackets - Die formed cold rolled sheet steel 18 gauge thick
Joining system - Die cast Zinc (0.95" nominal) and die Formed galvanized sheet 18 gauge
Reflectors - Extruded Aluminum (0.075” nominal) up to 95% reflective matte
End plate - Die formed cold rolled sheet steel 18 gauge thick
WEIGHT
Via 2 4ft - 9.03lbs - 4.1kg
Via 2 8ft - 18.28lbs - 8.3kg
Via 2 12ft - 27.97lbs - 12.7kg
CERTIFICATIONS
ETL - Rated for Dry/Damp locations. Conforms to UL Standard 1598 and certified to CAN/CSA
Standard C22.2 No. 250.0.
Chicago plenum - City of Chicago Approved (CCEA)
WARRANTY
LumenWerx provides a five-year limited warranty of electrical and mechanical performance of the
luminaires, including the LED boards, drivers, and auxiliary electronics. LumenWerx will repair or
replace defective luminaires or components at our discretion, provided they have been installed
and operated in accordance with our specifications. Other limitations apply, please refer to the full
warranty on our website.
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
File Name: VIA2_PLUS.RECESSED.VERTICAL.SPEC
LumenWerx ULC. reserves the right to change or modify product specifications without notification
February 20, 2015
Page: 3 / 3