Warranty Information:
Products for Home Use
For warranty issues please contact the retailer directly at:
1-800-843-2446
or
Calabria 68" x 40" Rectangular Table
Instruction Manual
www.Overstock.com
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
CONTACT OVERSTOCK.COM CUSTOMER SERVICE AT
1-800-843-2446
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
OV SKU No. 10090641-000-000
Model No. 50104089
Read the instructions and precautions before use of this product
Made in China
310106rev1
Distributed by:
Overstock.com
6350 South 3000 East
Salt Lake City, UT 84121
Please keep this instruction manual for future reference
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
CONTACT CONSUMER SUPPORT AT
1-800-843-2446
PARTS LIST
PART #
A
B
C
D
E
F
G
H
J
K
L
M
DESCRIPTION
QUANTITY
1
4
1
8
8
8
24
8
16
8
1
1
Table Top
Table Leg
Leg Connector Bracket
Short Bolt
Long Bolt
Hex Nut
Metal Washer
Lock Washer
Plastic Bolt Cap
Plastic Nut Cap
Angle Wrench
Hex Wrench
Parts Detail
B
C
A
D
E
K
L
F
G
H
J
M
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT
1-888-424-3354
NOTE: This product is intended for residential, non-commercial use.
1
ASSEMBLY INSTRUCTIONS
CAUTION: Do not over tighten
hardware.
Figure 1
Install Table Legs
Figure 2
Detail A
Top Left Corner of Table
L
1. (SEE FIGURE 1) Place table top (A)
upside down on non-scratch surface.
2. Align one table leg (B) with corner of
table top (A).
3. Attach table leg to table top using
two short bolts (D), lock washers (H
and metal washers (G). Loosely tighten
hardware using angle wrench (L).
4. Repeat steps 1 - 3 with remaining
table legs. Tighten hardware once
each leg is in place.
J
B
Table Leg
B
J
E
M
E
C Leg Connector
Bracket
G
G
G
F
G
K
H
G
A
K
F
D
G
H
D
B
C
Install Leg Connector Bracket
1. (SEE FIGURE 2) Place leg connector bracket (C) in center of table legs.
2. Attach leg connector bracket (C) to top left table leg using two long bolts (E)
and metal washers (G).
3. Place one metal washer (G) onto each long bolt (E). Slide each bolt through table leg
then leg connector bracket.
4. Secure leg connector bracket to table leg from inside of bracket, using two metal washers (G)
and two hex nuts (F). Tighten leg bracket hardware using angle wrench (L) and hex wrench (M).
5. Repeat for remaining table legs.
Install Plastic Bolt Caps
1. (SEE FIGURE 2) Place one plastic bolt cap (J) on end of each short and long bolt (D, E).
Install Plastic Nut Caps
1. (SEE FIGURE 2) Locate hex nuts inside center of leg connector bracket (C).
Place one plastic nut cap (K) onto each hex bolt.
2. Place table upright. Your table is now ready to use.
A
Detail B
Bottom Right Corner of Table
K
Leg Connector
C Bracket
F
G
K
F
G
G
G
E
J
2
3
E
J
Table
B Leg