OmniReach®
72-Port Fiber Splitter Box (FSB)
User Manual
ADCP-96-151 • Issue 1 • 8/2008
22919-A
Content
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1
2
3
4
1447966 Rev A
DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1
General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2
Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3
Main Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4
Specifications and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1
Standard Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2
Installing a Splitter (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.3
Installing a Splice Tray (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
OPERATION METHODS AND PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.1
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2
Service Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3
Service Disconnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4
Connector and Adapter Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CUSTOMER INFORMATION AND ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Page 1
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
INTRODUCTION
This manual contains a description and installation and cable routing instructions for the ADC
72-Port Fiber Splitter Box (FSB).
Revision History
ISSUE
DATE
1
08/2008
REASON FOR CHANGE
Original.
Trademark Information
ADC and ADC Telecommunications are registered trademarks of ADC Telecommunications, Inc.
Admonishments
Important safety admonishments are used throughout this manual to warn of possible hazards to
persons or equipment. An admonishment identifies a possible hazard and then explains what
may happen if the hazard is not avoided. The admonishments — in the form of Dangers,
Warnings, and Cautions — must be followed at all times. These warnings are flagged by use of
the triangular alert icon (seen below), and are listed in descending order of severity of injury or
damage and likelihood of occurrence.
Danger: Danger is used to indicate the presence of a hazard that will cause severe personal
injury, death, or substantial property damage if the hazard is not avoided.
Warning: Warning is used to indicate the presence of a hazard that can cause severe personal
injury, death, or substantial property damage if the hazard is not avoided.
Caution: Caution is used to indicate the presence of a hazard that will or can cause minor
personal injury or property damage if the hazard is not avoided.
1
1.1
DESCRIPTION
General Description
The OmniReach 72-port Outdoor Fiber Splitter Box (FSB), shown on the front cover of this
manual and in Figure 1, is a weather-resistant service distribution box providing a convenient
means to split out signals from a network feeder cable to multiple subscribers in a commercial
Multiple Tenant Unit (MTU) or residential Dwelling Unit (MDU). The FSB is designed to be
mounted on the outside of the MTU or MDU building where it provides network technicians
with a simple “plug in when ready” service connection between the feeder cable and drop
cables routed to the individual units within the building.
Page 2
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
The FSB features a hinged service access deck that divides it into front and back areas with
different service applications. In its closed position, the deck serves as the interface for turning
up subscribers, in a switchboard fashion, by unplugging the splitter output connectors from a
“parking lot” (where they are positioned temporarily until assigned) and plugging them into
adapters that are in turn connected to drop cables. Swinging the service deck out on its hinge (as
shown in Figure 1) provides access to the back area of the FSB containing the feeder cable,
splice trays, splitters, and associated internal cables. This spatial arrangement conforms to the
typical use of the FSB since the front area is accessed fairly frequently (each time a new
subscriber is added) while the back area is usually accessed only once when the box is installed
or occasionally to add splice trays or splitters.
22927-A
Figure 1. 72-Port FSB With Service Access Deck Swung Out
In its maximum use configuration, the 72-port FSB accommodates 72 subscribers by splitting
12 network signal inputs into 72 outputs. The FSB is equipped with a sealed grommet cable
portal that accommodates a variety of feeder cable types. The feeder cable is secured within the
back area of the FSB using a standard-grip cable clamp providing the required strength against
accidental pull out.
The FSB construction of heavy gauge aluminum finished with a heavy powder coat protects
against rain, wind, dust, rodents, and corrosion while remaining lightweight for ease of
installation. The FSB is available either with or without factory-installed components including
feeder cable stub, splice trays, splitters, and internal cables. In the standard configuration, it is
shipped without a feeder cable but with splice trays, splitters, and internal cables. Several
different types of splitters offering a range of splitter ratios are available. Each unit is furnished
with a wall mount bracket.
Page 3
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
1.2
Function
Figure 2 is a schematic depicting the function of the 72-port Fiber Splitter Box. As shown, the
signal path goes from the feeder cable to the splice tray and from there to the splitters. From the
splitter, in an active circuit, the multiple outputs are routed through internal cables to the
adapters from which the signal travels through drop cables to the subscriber premises.
The parking lot provides temporary storage for the internal cables carrying unassigned splitter
outputs.
FROM
NETWORK
FEEDER
CABLE
SPLITTER
SPLICE
TRAY
INTERNAL
PIGTAILS
ADAPTER
PACKS
PARKING
LOT
RELOCATION
WHEN ASSIGNED
22938-A
DROP
CABLE
TO
SUBSCRIBER
Figure 2. FSB Function
1.3
Main Components
Figure 3 shows the main components of the FSB visible with the swing-out service access deck
closed. The called out components are as follows (in alphabetical order):
Page 4
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
• Cable Guide for Drop Cables—hold drop cables in the optimum physical route for
passage through the drop cable portal to the adapters.
• Cable Guides for Pigtails from Splitters—hold the internal pigtails in the optimum
physical route between the splitters and the parking lot and adapters.
• Designation Label—is used to record assignment of splitter outputs to subscribers.
• Drop Cable Portal—is the opening into the FSB for drop cables to subscribers.
• Feeder Cable Portal—is the opening into the FSB for the network feeder cable.
• Ground Cable—is used to connect the door to the chassis ground lug which is in turn
connected by a ground wire to office ground.
• Mounting Ears—(two on top, two on bottom) are used to hang the FSB on fours screws
installed in the wall.
• Parking Lot—provides temporary storage for the connectorized ends of the internal
pigtails from the splitters. When a splitter output is assigned to a customer, the associated
connector is unplugged from the parking lot and plugged into an adapter.
• Sliding Adapters Packs—are the physical interface used to connect drop cables to splitter
output cables. The adapters packs contain six adapters each. The adapter packs have a end
latch that is swung open to release the pack to slide it out for easier access.
MOUNTING
EARS
CABLE GUIDES
FOR PIGTAILS
FROM SPLITTERS
CABLE GUIDE
FOR DROP
CABLES
GROUND
CABLE
DESIGNATION
LABEL
DROP
CABLE
PORTAL
FEEDER
CABLE
PORTAL
PARKING
LOT
SLIDING
ADAPTER
PACKS
22922-A
SWING-OUT
SERVICE
ACCESS DECK
SPLITTERS
Figure 3. FSB Main Components Visible With Service Access Deck Closed
Page 5
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
Figure 4 shows the main components of the FSB visible with the service access deck swung out.
The called out components are as follows (in alphabetical order):
• Cable Clamp—secures the feeder cable to the back wall of the box.
• Cable Guides for Splice Trays—hold the cables that are wound around the splice tray
and into a splice chip for splicing. These cables include feeder cables and the internal
pigtails that transition between the splice trays and splitters.
• Ground Lug—is used to ground the box to office ground. An internal cable connects the
ground lug to the box door.
• Splice Trays—hold the splice chips on which the feeder cable fibers are spliced to internal
pigtails to the splitters. Mechanical and heat shrink fusion splice chips are available.
• Splitters—split a single signal received on a feeder fiber into multiple outputs to
subscribers. Various splitters ratios are available (see Table 1 on Page 7).
• Swing-Out Service Access Deck—holds the parking lot and adapters; swings out to
provide better access to the feeder cable, splice trays, and splitters.
SPLICE
TRAYS
SWING-OUT
SERVICE
ACCESS DECK
FEEDER
CABLE
PORTAL
GROUND
LUG
CABLE
CABLE
CLAMP
GUIDES FOR
SPLICE TRAY
Figure 4. FSB Main Components Visible With Service Access Deck Swung Out
Page 6
© 2008, ADC Telecommunications, Inc.
22923-A
SPLITTERS
ADCP-96-151 • Issue 1 • 8/2008
1.4
Specifications and Dimensions
Figure 5 shows dimensions of the 72-port FSB. Table 1 lists specifications.
27.36 IN.
(69.5 CM)
19.0 IN.
(48.3 CM)
3.0 IN.
(7.6 CM)
9.22 IN.
(23.4 CM)
8.36 IN.
(21.2 CM)
13.0 IN.
(33.0 CM)
13.54 IN.
(34.4 CM)
15.24 IN.
(38.7 CM)
16.27 IN.
(41.3 CM)
4.38 IN.
(11.1 CM)
10.25 IN.
(26.0 CM)
22921-A
Figure 5. Dimensions
Table 1. 288 Cabinet With Splicing Specifications
PARAMETER
SPECIFICATION
Box
Dimensions (H x W x D)
13.54 x 19.0 x 8.36 x inches (34.4 x 48.3 x 21.2 cm)
Weight (fully loaded)
30 lbs (13.64 kg)
Distribution ports
Up to 72
Distribution port adapters/connectors
SC/APC
Splitter compartment capacity
3 splitters
Page 7
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
Table 1. 288 Cabinet With Splicing Specifications, continued
PARAMETER
SPECIFICATION
Parking lot capacity
Up to 32 connectors
Sliding adapter pack capacity
72 adapters (12 packs each with 6 adapters)
Splitter Modules
2
Splitter module input and output pigtails
Bend-optimized fiber terminated
with UPC/SC or APC/SC connectors
Test bandpass
1260–1360 nm, 1480–1500 nm, 1550–1560 nm
Overall bandpass
1260–1625 nm
Return loss at test bandpass
>55 dB
Maximum insertion loss at test bandpass
1x4
1x8
1 x 16
1 x 32
1 x 64
2 x 16
2 x 32
Dual 1 x 4
Dual 1 x 8
Dual 1 x 16
Note: Includes loss from input and output connectors
7.8 dB
110.9 dB
14.1 dB
17.3 dB
21 dB
14.7 dB
18 dB
xx dB
xx dB
xx dB
INSTALLATION
This section includes detailed instructions on how to install an FSB.
This section includes a standard procedure and optional procedures. The standard procedure is
for an FSB with no feeder cable stub and with splice trays, splitter input cables, splitters, and
splitter output cables having been installed at the factory. The optional procedures are for use
when splice trays or splitters are being installed onsite.
To allow full access into the FSB, ADC recommends choosing a mounting area with at least 13
inches (33 cm) space on the left (hinged side) of the enclosure, and 19 inches (48 cm) in front of
the enclosure.The portals for the feeder (input) cable and drop (output) cables are on the bottom
of the FSB.
Warning: Never install equipment in a wet location or during a lightning storm. When
installing or modifying communication lines, disconnect lines at the network interface before
working with uninsulated lines or terminals.
Page 8
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
2.1
Standard Installation
Installation of the FSB involves the following tasks:
1. Mounting the cabinet on the wall.
2. Preparing and installing the feeder cable.
3. Splicing the feeder cable fibers to the already present splitter input fibers.;
Tools required for these procedures:
• Tape measure
• Level
• Drill with bit (typically for #12 wood screws)
• 1½ inch #12 wood screws
• Screwdriver
• Splice kit
Caution: Handle Cables with Care
Fiber optic cable stubs should be handled with care throughout the installation procedure to
avoid kinking and damage to cables.
Note: The wall surface must be strong enough to support the weight of the enclosure
(approximately 30 lbs (13.7 kg), not including stub cables) and appropriate hardware must
be used to secure the enclosure to the wall.
Install the FSB using the following procedure:
1. Using the FSB as a template, mark the locations for the top wall mounting holes. ADC
recommends a wall height of 60 inches (152 cm) for the top of the cabinet.
2. Drill the two holes for the top mounting hangers.
3. Screw two 1½-inch #12 wood screws into the holes, leaving about 1/2-inch (1 cm)
between the screw heads and the wall.
4. Lift the box into place and hang on the wall as shown in Figure 6.
5. Level the enclosure and tighten the two top screws.
6. Using the two bottom mounting brackets as guides, drill holes for the bottom mounting
brackets.
7. Using 1½-inch #12 wood screws, secure the bottom brackets to the wall.
8. Recheck the enclosure level and adjust, if necessary.
Page 9
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
22920-A
LAG BOLT
(4 PLACES)
Figure 6. Mounting FSB on Wall
9. Open the door of the cabinet using a 216-type can wrench. Swing open the service access
deck to provide access to the back area of the FSB.
10. Ground the FSB using #6AWG ground wire as follows. See Figure 7.
a. Pierce center of rubber grommet for small hole, just large enough to pass #6AWG wire
through.
Note: It is important to maintain a watertight seal.
b. Pass the grounding wire through the grommet.
c. Use the set screw in ground lug to secure grounding wire.
d. Connect the grounding wire to a known good ground.
Page 10
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
GROUND LUG
DETAIL
TO
OFFICE
GROUND
22924-A
Figure 7. Grounding the FSB
Note: It will be helpful to have a rolling table or stationary work surface near the FSB to
provide a flat surface for breaking out the cable and performing splices.
Note: Splitters and splitter cables are assumed to be already installed in this procedure
since this is the standard configuration. If not, refer to the optional procedures.
11. Route the feeder cable to the FSB and secure it as follows:
a. Remove the plug from the feeder cable portal.
b. Thread the cable through the compression nut and fitting on the bottom of the cabinet,
loosening the nut if necessary to allow the cable to pass through.
c. Pull through 6 feet (2 m) of the feeder cable into the FSB through the portal and onto a
flat surface near the FSB.
d. Finger tighten the compression fitting with the nut.
12. Break out the feeder cable per Figure 8.
Page 11
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
12 IN.
CUSTOMER ORDER LENGTH
BREAKOUT LENGTH
72 IN. (+0.0, -6.0)
SUBUNIT
12 IN.
22940-A
Figure 8. Feeder Cable Breakout
13. Remove the splice tray(s) from the rear of the enclosure by unspooling the splitter cables
from the cable guides. Place the splice tray(s) on the working surface.
14. Route the feeder cable fibers in the splice tray as shown in Figure 9.
FEEDER CABLE
22936-A
Figure 9. Feeder Cable Routing On Splice Tray (Splitter Cable Not Shown)
15. Splice the feeder cable fibers to the splitter cable fibers following local procedure.
16. Secure the feeder cable in the cable clamp as shown in Figure 10. Do not tighten the clamp
at this time so cable length within box can be adjusted as needed.
17. Spool the feeder cable and the splitter cables into the cable guides following the routing
shown in Figure 11.
18. Tighten the cable clamp bolts and compression nut to secure the feeder cable.
19. Swing closed the service access deck.
20. If installing drop cables at this time, refer to Section 2.2 on Page 14.
21. Close the FSB door and lock the door using the 216 wrench.
Page 12
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
22925-A
Figure 10. Installing Feeder Cable
22926-A
TIE OFF
POINT
FEEDER
CABLE
PIGTAILS
NOTE:
CABINET AND SWING FRAME
NOT SHOWN FOR CLARITY.
Figure 11. Installing a Splitter Input Cable
Page 13
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
2.2
Installing a Splitter (Optional)
1. Install the splitter in the splitter chassis as shown in Figure 12.
SPLITTER
CHASSIS
SPLITTER
22931-A
Figure 12. Installing a Splitter
2. Route the splitter input fibers on the splice tray as shown in Figure 13.
SPLITTER CABLE
22939-A
Figure 13. Splitter Input Fibers Routed On Splice Tray (Feeder Cable Fibers Not Shown)
Page 14
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
3. Splice the splitter input fibers to the feeder fibers per local practice.
4. Spool the cables into the cable guides following Figure 11 on Page 13.
5. Route the splitter output fibers to the parking lot as shown in Figure 14.
SLIDING
ADAPTER
PACKS
PARKING
LOT
SPLITTER
SPLITTER TO
PARKING LOT ROUTING
(VIEWED FROM THE RIGHT)
SPLITTER
SLIDING
ADAPTER
PACKS
SPLITTER TO
PARKING LOT ROUTING
(VIEWED FROM THE LEFT )
PARKING
LOT
22932-A
Figure 14. Splitter Output Cable Routing (Splitter Input Cables Not Shown)
Page 15
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
2.3
Installing a Splice Tray (Optional)
If required, install a splice tray by unbinding the velcro strap and placing the new splice tray
into position as shown in Figure 15. Secure the splice tray using the velcro strap.
VELCRO
STRAP
SPLICE
TRAY
22933-A
Figure 15. Installing a Splice Tray
3
OPERATION METHODS AND PROCEDURES
This section includes detailed instructions on steps required to put the ODE into service, and
steps that may be required during the operational life of the ODE.
3.1
Safety Precautions
Follow these guidelines for safe operation and fiber handling procedures.
Danger: Avoid Eye Exposure to Unmated Connectors
Unmated connectors may emit invisible laser radiation. Do not look directly into the end of a
connector or an adapter port. Do not inspect with a magnifying device. To ensure safety
maintain caps on unmated connectors at all times.
Caution: This Enclosure Is For Use with Passive Components Only
This enclosure is not rated or approved for use with active electronic components.
Page 16
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
Caution: Use Optical Caps
Connector plug caps and adapter covers should always be used on unmated connectors and
ports. Plug caps should be kept on pre-connectorized pigtails during routing in order to prevent
damage to the polished end face on the connector.
Caution: Do Not Use Tie Wraps on Fiber
Cable ties should not be cinched tightly secured around fiber jumpers because they may induce
fiber loss or even damage fibers. Ties may be used for containment only, but not for tight
wrapping.
Caution: Maintain Fiber Minimum Bend Radius
Fiber jumper cables must be arranged in turns, bends, and loops not less than the minimum
bending radius of the cable. For individual jacketed jumpers (2 mm) and pigtails (0.9 mm)
supplied with the ODE enclosure bend radius should not exceed a minimum of 1.5-inches (38
mm). Outdoor stub cables should not exceed a bend diameter of 20x the cable diameter.
Caution: Handle Fiber with Care
Do not tug, twist or tie fiber cables while handling fiber.
3.2
Service Connection
Follow these procedures for making service connections.
Danger: Avoid Eye Exposure to Unmated Connectors
Unmated connectors may emit invisible laser radiation. Do not look directly into the end of a
connector or an adapter port. Do not inspect with a magnifying device. To ensure safety
maintain caps on unmated connectors at all times.
Caution: Handle Fiber with Care
Do not tug, twist or tie fiber cables while handling fiber.
Note: Clean both the adapter and connector according to local standards as required when
putting into service.
1. Open the FSB door with a 216-type can wrench.
2. Route the drop cable to the drop cable portal and thread it through as shown in Figure 16.
Allow the cable to drape over the bottom of the open box.
3. Identify the connector in the parking lot assigned to the drop cable.
4. Identify the adapter assigned to the drop cable.
5. Release the corresponding adapter pack tab and slide out the pack.
Danger: Avoid Eye Exposure to Unmated Connectors
Unmated connectors may emit invisible laser radiation. Do not look directly into the end of a
connector or an adapter port. Do not inspect with a magnifying device. To ensure safety
maintain caps on unmated connectors at all times.
Page 17
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
6. Remove the protective cap and dust cap from assigned connector.
7. Unplug the assigned connector from the parking lot and plug it into the assigned adapter.
8. Record the splitter out fiber and adapter used on the designation label.
9. Close and secure the door when all service connections are complete.
CABLE GUIDE
FOR DROP
CABLES
DROP CABLE TO
SUBSCRIBER
22937-A
Figure 16. Installing a Feeder Cable
3.3
Service Disconnection
Follow these procedures for service disconnections.
Danger: Avoid Eye Exposure to Unmated Connectors
Unmated connectors may emit invisible laser radiation. Do not look directly into the end of a
connector or an adapter port. Do not inspect with a magnifying device. To ensure safety
maintain caps on unmated connectors at all times.
Caution: Handle Fiber with Care (see section 3.1)
1. Open enclosure door with 216-type can wrench.
2. Identify drop fiber assigned for disconnection.
3. Remove the connector from the appropriate adapter.
4. Identify the corresponding storage position in the parking lot.
Page 18
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
5. Remove the protective cap and dust cap from the storage position, and move dust cap to
the subscriber port just disconnected.
6. Place pigtail plug protective cap on plug and connect the plug to the storage adapter.
7. As necessary, change information noted on the designation label.
8. Close and secure doors when all service connections are complete.
3.4
Connector and Adapter Cleaning
Note: It is recommended that the craft follow local standard cleaning procedure when
cleaning connectors and adapters.
Note: Alternate cleaning procedures are available from ADC for use in especially dirty
environments.
1. ADC recommends dry cleaning first with lint free materials, such as Chemtronics®
QbE™ wipes for connectors and Coventry™ 2.5mm fiber optic swabs for adapters.
Note: Always use a fresh wipe or swab for each connector or adapter.
2. If dry cleaning does not produce the desired results, use a small amount of solvent (fast
drying). A non isopropyl alcohol (IPA) solvent is recommended (such as Chemtronics PX
wash).
3. For connectors, apply approximately a dime size area of solvent on a wipe, pass the
connector through the moistened area of the wipe, then make several passes over the dry
area of the wipe. Never re-use an area of the wipe after passing the connector over it.
4. For adapters, apply a small drop of solvent on the swab, gently insert into the adapter’s
ferule until it contacts the connectors end-face, turn the swab three complete turns.
5. If there is a need to moisten a connector end face or adapter, it must be blown dry with
clean compressed air.
Page 19
© 2008, ADC Telecommunications, Inc.
ADCP-96-151 • Issue 1 • 8/2008
4
CUSTOMER INFORMATION AND ASSISTANCE
PHONE:
U.S.A. or CANADA
Sales:
1-800-366-3891
Extension
73000
Technical Assistance: 1-800-366-3891
Connectivity Extension:
73475
Wireless Extension:
73476
EUROPE
Sales Administration: +32-2-712-65 00
Technical Assistance: +32-2-712-65 42
EUROPEAN TOLL FREE NUMBERS
Germany:
0180 2232923
UK:
0800 960236
Spain:
900 983291
France:
0800 914032
Italy:
0800 782374
ASIA/PACIFIC
Sales Administration: +65-6294-9948
Technical Assistance: +65-6393-0739
ELSEWHERE
Sales Administration: +1-952-917-3000
Technical Assistance: +1-952-917-3475
13944-Q
WRITE:
ADC Telecommunications (S’PORE) PTE, LTD;
100 Beach Road, #18-01, Shaw Towers.
Singapore 189702.
ADC Telecommunications, INC
PO Box 1101,
Minneapolis, MN 55440-1101, USA
ADC European Customer Service, INC
Belgicastraat 2,
1930 Zaventem, Belgium
PRODUCT INFORMATION AND TECHNICAL ASSISTANCE:
[email protected]
[email protected]
[email protected]
[email protected]
REPRINTS:
PDF copies of manuals are available
for downloading at the following link:
www.adc.com/manuals
ADCP Number:
96-151
Contents herein are current as of the date of publication. ADC reserves the right to change the contents
without prior notice. In no event shall ADC be liable for any damages resulting from loss of data,
loss of use, or loss of profits and ADC further disclaims any and all liability for indirect, incidental,
special, consequential or other similar damages. This disclaimer of liability applies to all products,
publications and services during and after the warranty period.
Page 20
© 2008, ADC Telecommunications, Inc.