Product Data Sheet AGM0112 08/2012
AcryGlaze Matt Clear Acrylic Enamel
AcryGlaze Gloss combines the toughness of enamel paint with the ease of an acrylic paint.
It is a water based alternative to clear solvent systems and is particularly suited to interior
applications over dressed timber and wooden joinery.
Product features
Film properties
Tough film – high resistance to damage
Heat resistance – 70˚C maximum
Fast dry – quicker job turnaround
Water resistance – excellent – suitable for all internal
wet areas such as bathrooms, laundries and kitchens
Low odour – reoccupy times reduced
Clarity stable – will not yellow
Typical areas of use
Chemical resistance – resistant to household
cleaners: avoid acids and alcohols
Solvent resistance – poor resistance to strong solvents
Protecting movie/TV set construction materials
and paint work
Gloss
Developing the grain and protecting interior timber
trim and doors
Gloss level and description – matt 5–7% @
60 degrees
Enhancing the natural beauty of stone work
Protective over coating for paint effects
Precautions
Safety
Read label before use and keep out of reach
of children.
AcryGlaze Matt is not recommended for exterior use
If medical advice is needed: have product container
or label at hand.
Environmental qualities
Wear protective clothing such as overalls, goggles
and gloves and ventilate working areas.
Manufactured in a carbon neutral certified facility –
ISO 14064-1
VOC 18gms per litre EC07-09
Wash any paint deposits off skin.
If sanding wear face mask to avoid inhaling
dust particles.
Ecolabel certified – Environmental Choice EC07-09
Licence number 070301
Page 1 of 2
PaintPlus Colour Systems Ltd PO Box 101366 North Shore Auckland 0745 ph +64 9 912 84 74
www.paintplus.co.nz [email protected]
Product specifications change from time to time and may differ from those published.
Application methods
General preparation of the surface to be painted
should be completed before commencing
application.
Good quality paint or cutting in brush
All loose material must be removed and surface
damage or imperfections made good.
The surface must be clean, dry and free of
contaminants.
Application schedule
Touch dry 15 minutes
Re-coat time (minimum) 2 hours
Curing time 7 days
Practical coverage 12–15 square meters per litre
Short nap roller – 4.5mm–8mm
Clean up and thinning
Clean up all equipment with water.
On very dry substrates or, in warm and/or low
humidity, AcryGlaze Matt may be thinned by
the addition of up to 50mls of water per litre.
Hot weather – thinners may be added during very
hot weather at the rate of up to 50mls per litre.
Excessive thinning will lengthen drying times
and may have a detrimental impact on handling
characteristics.
Dry film thickness @ 12 square meters per litre
22 microns per coat
Application is not recommended if the surface and/
or air temperature is less than 10˚C or is liable to fall
below 10˚C during the drying period.
Paint requirements
New timber joinery and doors
3 coats at 12–15 square meters per litre per coat
Sand between coats if grain raising occurs
Paint effects
Compatibility should be evaluated before proceeding
2–3 coats 12–15 square meters per litre per coat
Page 2 of 2
PaintPlus Colour Systems Ltd PO Box 101366 North Shore Auckland 0745 ph +64 9 912 84 74
www.paintplus.co.nz [email protected]
Product specifications change from time to time and may differ from those published.
Product Data Sheet AGM0112 08/2012
Surface preparation
Product Data Sheet ASG0112 08/2012
AcryGlaze Semi Gloss Clear Acrylic Enamel
AcryGlaze Semi Gloss combines the toughness of enamel paint with the ease of an acrylic
paint. It is a water based alternative to clear solvent systems and is particularly suited to
interior applications over dressed timber and wooden joinery.
Product features
Film properties
Tough film – high resistance to damage
Heat resistance – 70˚C maximum
Fast dry – quicker job turnaround
Water resistance – excellent – suitable for all internal
wet areas such as bathrooms, laundries and kitchens
Low odour – reoccupy times reduced
Clarity stable – will not yellow
Typical areas of use
Chemical resistance – resistant to household
cleaners: avoid acids and alcohols
Solvent resistance – poor resistance to strong solvents
Protecting movie/TV set construction materials and
paint work
Gloss
Developing the grain and protecting interior timber
trim and doors
Gloss level and description – semi gloss 35% @
60 degrees
Enhancing the natural beauty of stone work
Protective over coating for paint effects
Precautions
AcryGlaze Semi Gloss is not recommended for
exterior use
Environmental qualities
Manufactured in a carbon neutral certified facility –
ISO 14064-1
Safety
Read label before use and keep out of reach
of children.
If medical advice is needed: have product container
or label at hand.
Wear protective clothing such as overalls, goggles
and gloves and ventilate working areas.
Wash any paint deposits off skin.
If sanding wear face mask to avoid inhaling
dust particles.
VOC 19gms per litre EC07-09
Ecolabel certified – Environmental Choice EC07-09
Licence number 070301
Page 1 of 2
PaintPlus Colour Systems Ltd PO Box 101366 North Shore Auckland 0745 ph +64 9 912 84 74
www.paintplus.co.nz [email protected]
Product specifications change from time to time and may differ from those published.
Application methods
General preparation of the surface to be painted
should be completed before commencing
application.
Good quality paint or cutting in brush
All loose material must be removed and surface
damage or imperfections made good.
The surface must be clean, dry and free of
contaminants.
Short nap roller – 4.5mm–8mm
Clean up and thinning
Clean up all equipment with water.
Areas with a build up of grime must be cleaned
with sugar soap or quality equivalent.
On very dry or absorbent substrates or, in warm
and/or low humidity, AcryGlaze Semi Gloss may
be thinned by the addition of up to 50mls of water
per litre.
Application schedule
Hot weather thinners may be added during very
hot weather at the rate of up to 50mls per litre.
Touch dry 15 minutes
Excessive thinning will lengthen drying times
and may have a detrimental impact on handling
characteristics.
Re-coat time (minimum) 2 hours
Curing time 7 days
Practical coverage 12–15 square meters per litre
Dry film thickness @ 12 square meters per litre
26 microns per coat
Application is not recommended if the surface and/
or air temperature is less than 10˚C or is liable to fall
below 10˚C during the drying period.
Paint requirements
New timber joinery and doors
3 coats at 12–15 square meters per litre per coat
Sand between coats if grain raising occurs
Paint effects
Compatibility should be evaluated before proceeding
2–3 coats at 12–15 square meters per litre per coat
Page 2 of 2
PaintPlus Colour Systems Ltd PO Box 101366 North Shore Auckland 0745 ph +64 9 912 84 74
www.paintplus.co.nz [email protected]
Product specifications change from time to time and may differ from those published.
Product Data Sheet ASG0112 08/2012
Surface preparation
Product Data Sheet AGG0112 08/2012
AcryGlaze Gloss Clear Acrylic Enamel
AcryGlaze Gloss combines the toughness of enamel paint with the ease of an acrylic paint.
It is a water based alternative to clear solvent systems and is particularly suited to interior
applications over dressed timber and wooden joinery.
Product features
Film properties
Tough film – high resistance to damage
Heat resistance – 70˚C maximum
Fast dry – quicker job turnaround
Water resistance – excellent – suitable for all internal
wet areas such as bathrooms, laundries and kitchens
Low odour – reoccupy times reduced
Clarity stable – will not yellow
Typical areas of use
Chemical resistance – resistant to household
cleaners: avoid acids and alcohols
Solvent resistance – poor resistance to strong solvents
Protecting movie/TV set construction materials and
paint work
Gloss
Developing the grain and protecting interior timber
trim and doors
Gloss level and description – gloss 80% @ 60 degrees
Enhancing the natural beauty of stone work
Safety
Protective over coating for paint effects
Read label before use and keep out of reach
of children.
Precautions
If medical advice is needed: have product container
or label at hand.
AcryGlaze Gloss is not recommended for
exterior use
Environmental qualities
Manufactured in a carbon neutral certified facility –
ISO 14064-1
Wear protective clothing such as overalls, goggles
and gloves and ventilate working areas.
Wash any paint deposits off skin.
If sanding wear face mask to avoid inhaling
dust particles.
VOC 19gms per litre EC07-09
Ecolabel certified – Environmental Choice EC07-09
Licence number 070301
Page 1 of 2
PaintPlus Colour Systems Ltd PO Box 101366 North Shore Auckland 0745 ph +64 9 912 84 74
www.paintplus.co.nz [email protected]
Product specifications change from time to time and may differ from those published.
Application methods
General preparation of the surface to be painted
should be completed before commencing
application.
Good quality paint or cutting in brush
All loose material must be removed and surface
damage or imperfections made good.
The surface must be clean, dry and free
of contaminants.
Areas with a build up of grime must be cleaned
with sugar soap or quality equivalent.
Application schedule
Touch dry 15 minutes
Re-coat time (minimum) 2 hours
Short nap roller – 4.5mm–8mm
Clean up and thinning
Clean up all equipment with water.
On very dry or absorbent substrates or, in warm and/
or low humidity AcryGlaze Gloss may be thinned by
the addition of up to 50mls of water per litre.
Hot weather – thinners may be added during very
hot weather at the rate of up to 50mls per litre.
Excessive thinning will lengthen drying times
and may have a detrimental impact on handling
characteristics.
Curing time 7 days
Practical coverage 12–15 square meters per litre
Dry film thickness @ 12 square meters per litre
24 microns per coat
Application is not recommended if the surface and/
or air temperature is less than 10˚C or is liable to fall
below 10˚C during the drying period.
Paint requirements
New timber joinery and doors
3 coats at 12–15 square meters per litre per coat
Sand between coats if grain raising occurs
Paint effects
Compatibility should be evaluated before proceeding
2–3 coats at 12–15 square meters per litre per coat
Page 2 of 2
PaintPlus Colour Systems Ltd PO Box 101366 North Shore Auckland 0745 ph +64 9 912 84 74
www.paintplus.co.nz [email protected]
Product specifications change from time to time and may differ from those published.
Product Data Sheet AGG0112 08/2012
Surface preparation