Required Equipment
•
•
•
•
Ion meter or pH/mV meter.
Wash bottle with distilled or deionized water.
Several clean beakers.
1 mL, 10 mL and 100 mL pipettes.
Required Solutions
•
Reference Fill Solution (for both Silver & Sulfide)
YSI #400434
•
1000 ppm Silver Standard YSI #400438
•
100 ppm Silver Standard YSI #400437
•
Silver Ionic Strength Adjustor (ISA) YSI #400435
•
Sulfide Ionic Strength Adjustor (ISA) YSI #400436
NOTE: Sulfide Standards are unstable and must be prepared
carefully by the customer
Overview
The YSI 400433 Silver/Sulfide Ion Selective Electrode is a
combination electrode (includes both reference and sensing
half cells in one body housing) for measuring silver ion (Ag+) or
sulfide ion (S2-) activity in aqueous samples.
• Technology: Fixed position, solid state sensor
• Size and material:
Body (Epoxy)—12 mm OD x 155mm L
Cap (ABS) —16 mm OD x 57mm L
Cable (Coax type) – 100cm
BNC Connector
• Reference: Double-junction, Ag/AgCl, ceramic pin junction,
refillable, potassium nitrate electrolyte
• Features: long-lasting solid state sensor
• Range: 0.01-107,900 mg/L (Silver)
0.003-32,100 mg/L (Sulfide)
• Reproducibility: ±4%
• Slope: -26 to -29 mv/decade @ 25°C typical (Sulfide)
54 to 59 mv/decade @ 25°C typical (Silver)
• pH range: 2-12
• Operating Temperature: 0 to 80°C
• Interferences: Hg2+
• Applications/Notes: Industrial, environmental,
food/beverage
Electrode Preparation
1.
2.
This electrode performs better when the reference
junction is kept wetted during transit and storage.
Unscrew the cap of the storage solution bottle (Soaker
Bottle) and remove the electrode. Caution: Avoid
touching the sensor surface with your fingers.
Filling the electrode with electrolyte - the reference
(outer) chamber must be filled with Reference Fill
Solution and remain open during testing:
a) Slide the sleeve of the electrode FastFil cap down to
uncover the fill hole. (see fig. 1)
3.
4.
b) Shake the electrode downward like a thermometer to
remove any air bubbles trapped inside.
c) The surface of the Reference Fill Solution in the
reference chamber must be above the inner junction.
This is approximately 3" from the electrode tip.
Rinse the electrode with Dl water, blot dry. Do not rub
dry.
Soak the electrode in Dl water for 10 minutes, then in a
diluted Silver or Sulfide Standard Solution for two hours
prior to calibration or use.
Electrode Diagram (fig. 1)
Checking Electrode Operation (Slope)
1. Connect the electrode to the meter. Place 100 mL Dl water
into a 150 mL beaker. Add 2 mL Silver/Sulfide ISA to the
Dl water and stir thoroughly.
2. Set the function switch to the mV mode.
3. Rinse the electrode with Dl water, blot dry and place in the
solution prepared in step 2.
4. Pipet 1 mL of 1000 ppm Silver or Sulfide Standard into the
beaker. Stir thoroughly, then record the potential (E1) in mV
when a stable reading is displayed.
5. Pipette 10 mL of the same standard into the same beaker.
Stir thoroughly. When a stable reading is displayed, record
the potential (E2) in mV.
6. The difference between the first and the second potential
readings (E2-E1) is defined as the electrode slope. The
normal range for the slope is 27±2 mV at 25°C for Sulfide
analysis and 56±4 mV at 25°C for Silver analysis.
Troubleshooting
If the electrode slope is not within the normal range, the
following procedure may restore the electrode.
1. Soak the electrode in a diluted standard solution for 2
hours before use.
2. Repeat "Checking Electrode Operation" procedure again.
Note: All standard solutions should be prepared fresh. For
best performance use ISA in all solutions.
Periodically check the Reference Fill Solution level in the
reference chamber of the electrode. The solution level must be
higher than the inner junction which is visible as a white
ceramic pin on the inner body.
If the electrode slope is still outside the normal range after this
procedure, you may need to clean or replace the electrode.
Reading a Sample with the Electrode
Various procedures may be used to determine the
concentration of a sample. The most common is the Direct
Calibration method, which is described below. Contact YSI’s
technical service department for details of other methods.
In Direct Calibration a series of standard solutions of differing
concentrations are used to calibrate the electrode. Then each
sample requires only a single meter reading, which is
compared with the calibration readings to obtain the sample
concentration. ISA is added to all solutions to ensure the
samples and the standards have the same ionic strength.
Set up:
1. Prepare the electrode as described in "Electrode
Preparation" and "Checking Electrode Operation". Connect
the electrode to the meter.
2. Prepare two standard solutions that differ in concentration
by a factor of ten and bracket the expected sample
concentration range. For example, if your expected sample
concentration is 50 mg/L Silver or Sulfide, you should use
a 10 mg/L low Standard Solution and a 100 mg/L high
Standard Solution.
NOTE: Temperature compensation is not typical of ISE
measurements - for best performance, try to ensure that
the standards are within 5 to 10°C of the sample.
Measurement:
If using a meter with direct concentration reading capability
(see the meter instruction manual for specific information):
1. Place 100 mL of the low standard into a 150 mL beaker.
Add 2 mL of ISA. Stir thoroughly.
2. Rinse electrode with Dl water, blot dry and place in the
beaker. Wait for a stable reading, and then adjust the
meter to display the value of the standard. Refer to the
meter's instruction manual for the meter adjustment
procedure.
3. Measure 100 mL of the high standard into a second 150
mL beaker. Add 2 mL of ISA and stir.
4. Rinse electrode with Dl water, blot dry and place in the
second beaker. Wait for a stable reading, and then adjust
the meter to display the value of the second standard.
5. Pipette 100 mL of sample into a 150 mL beaker. Add 2 mL
of ISA. Stir thoroughly.
6. Rinse electrode with Dl water, blot dry and place in the
sample beaker. Wait for a stable reading and the sample
concentration will be displayed on the meter.
7. Determine the sample concentration using the calibration
curve prepared in Step 6 above.
Electrode Storage
Short Term (over night or the weekend):
Rinse the electrode thoroughly with Dl water and place the tip
in a diluted standard solution between measurements. Slide
the FastFil sleeve to close the fill hole.
Refill the reference before putting the electrode back into
service.
Long Term:
Refill the electrode with Reference Filling Solution and close
the fill hole. Put the soaker bottle (storage bottle) on the end of
the electrode with a wetted sponge to keep the reference from
drying out.
Follow procedures in "Electrode Preparation" and "Checking
Electrode Operation" before using the electrode again.
Electrode Cleaning
Cleaning should only be attempted if troubleshooting methods
fail. The solid state sensor can be buffed with a light cloth or
polishing strip if it shows signs of oxidation or precipitate
formation. It can also be rinsed vigorously under warm water
to remove debris. Soaking for 10-15 minutes in DI water might
be useful in extracting other contaminants.
Recondition the electrode by soaking in a low standard
solution immediately after any cleaning method.
Warranty Statement
The YSI TruLine Silver/Sulfide ISE is warranted for twelve (12)
month from date of purchase by the end user against defects
in materials and workmanship. Within the warranty period, YSI
will repair or replace, at its sole discretion, free of charge, any
product that YSI determines to be covered by this warranty.
To exercise this warranty, call your local YSI representative, or
contact YSI Customer Service in Yellow Springs, Ohio at +1
937 767-7241, 800-897-4151, [email protected] or visit ysi.com
(Support tab). Send the product and proof of purchase,
transportation prepaid, to the Authorized Service Center
selected by YSI. Repair or replacement will be made and the
product returned, transportation prepaid. Repaired or replaced
products are warranted for the balance of the original warranty
period, or at least 90 days from date of repair or replacement.
LIMITATION OF WARRANTY
This Warranty does not apply to any YSI product damage or
failure caused by:
1)
2)
3)
4)
5)
6)
failure to install, operate or use the product in
accordance with YSI's written instructions;
abuse or misuse of the product;
failure to maintain the product in accordance with YSI's
written instructions or standard industry procedure;
any improper repairs to the product;
use by you of defective or improper components or parts
in servicing or repairing the product;
modification of the product in any way not expressly
authorized by YSI.
THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. YSI's LIABILITY UNDER
THIS WARRANTY IS LIMITED TO REPAIR OR
REPLACEMENT OF THE PRODUCT, AND THIS SHALL BE
YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY
DEFECTIVE PRODUCT COVERED BY THIS WARRANTY.
IN NO EVENT SHALL YSI BE LIABLE FOR ANY SPECIAL,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM ANY DEFECTIVE PRODUCT COVERED
BY THIS WARRANTY.
YSI
1725 Brannum Lane
Yellow Springs, OH
Tel: +1 937-767-7241
800-765-4974
[email protected]
ysi.com
DOCUMENT ID: 400433MAN AUG2014C