WALL ADHESIVE
TECHNICAL DATASHEET
Version: 2017-03-20
PRODUCT DESCRIPTION
Wall Adhesive is a wallpaper adhesive for putting up different paper-based material in dry areas.
AREA OF USAGE
Wall Adhesive is suitable for putting up paper and acrylic structure wallpapers. The surface can be absorbent such as plasterboard,
chipboard and fibreboard, concrete or plaster or dense such as painted surfaces. Apply the adhesive using a roller, brush or wallpaper machine.
WORKING INSTRUCTION
Preparation: Gips-, spån- och boardskivor: Spackle board joints and screw holes, sand and pre-glue the spackled surfaces. Concrete or plaster: Spackle, sand and pre-glue the spackled surfaces. Existing paper wallpaper: Remove loose wallpaper and cut up in the corners. Spackle, sand and pre-glue holes, joints and unevenness. Paper-based vinyl wallpaper:
Loosen and tear away the top layer. Otherwise do the same as for paper wallpaper. Painted surfaces: Sand and wash with
paint wash and rinse with water. Spackle grind and pre-glue unevenness. Grind surfaces painted with primer. Pre-gluing: Dilute with 1 part water. Putting up: Apply the adhesive in an even layer on the back of the wallpaper with a roller, brush or
wallpaper machine. Avoid getting adhesive on the front of the wallpaper. Fold the sheets together and let them sit for a few minutes. Glue max. 10-15 sheets at a time. Press the wallpaper carefully with a suitable tool. Follow the material manufacturer's
instructions
SAFETY
The product’s contents are not classed as hazardous to health or flammable according to applicable legislation. For more information, refer to the Safety Data Sheet.
CONTACT US
Smart
TEL
+46 help
(0)42-19 50 00
[email protected]
1-800-726-7845
Bostik AB, Strandbadsvägen 22, Box 903, SE-251 09 Helsingborg Tlf: +46
(0)42-19 50 00, Fax: +46 (0)42 19 50 21, www.bostik.se
Disclaimer: The technical data we present, as well
as our instructions and recommendations are all
based on a variety of tests and our experience. They are intended to help the
user to find the most suitable working method and get the best possible results.
Since the users working conditions is beyond our control, we cannot accept any
responsibility for the results obtained by the product.
TECHNICAL DATA
Adhesive type
Simple adhesive
Bonding agent
Modified starch
Solvent
Water
Consistency
Thixotrope
Colour
Off-white
Application tools
Roller, brush or wallpaper
machine following the instructions of the wallpaper manufacturer
Working temperature
Not under + 18°C
Cleaning agent
Clean tools with water. Wash
off adhesive residue with a
damp cloth or sponge before
drying.
Density
1.04 g/cm3
Solids content
13 ± 2 % weight
%
Adhesive usage
Approximately 4 m²/litre depending on the material and
application method
Thinner
Water. The adhesive should
not be thinned
Flammable
No
Storage
12 months at 10 to 20°C in
unopened package, Protect
against frost
CONTACT US
TEL 042-19 50 00
[email protected]
Bostik AB, Strandbadsvägen 22, Box 903, SE-251 09 Helsingborg Tlf: +46
(0)42-19 50 00, Fax: +46 (0)42 19 50 21, www.bostik.se
Disclaimer: The technical data we present, as well
as our instructions and recommendations are all
based on a variety of tests and our experience. They are intended to help the
user to find the most suitable working method and get the best possible results.
Since the users working conditions is beyond our control, we cannot accept any
responsibility for the results obtained by the product.