10' Wave-2 Plus Telescopic Jib Arm
Crane film production package
(P-WV-2PL-PP)
All rights reserved
No part of this document may be reproduced, stored in a retrieval system, or transmitted by any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, except as may be expressly permitted
by the applicable copyright statutes or in writing by the publisher.
PROAIM 10' Wave-2 Plus Telescopic Jib Arm Crane Film Production Package
2
INTRODUCTION
PROAIM welcomes you to the new and modernized era with its Proaim 10' Wave-2 Plus
Telescopic Jib Arm Crane with CST-100 Stand, Portable Dolly, SR. Pantilt head & Zoom Controller
a portable filming solution to increase your production value. The Robust jib crane is specifically
designed travel crane for indoor & outdoor video productions. Its telescopic arm feature adds
flexibility to frame perfect shots in indoor and outdoor spaces. This video production package
includes a rugged camera dolly for smooth, dynamic moving shots and rock solid aluminum
tripod stand for immense support. Now you can create the visual effects and produce incredibly
smooth floating camera crane shots that add value to your filming productions and bring a quick
return on your investment.
IN THE BOX
Please inspect the contents of your shipped packages to ensure you have received all that
is pictured and listed below. The grey foam shipping /storage containers have been
especially designed to protect your purchase while in transit and is a good place to keep
your Proaim Jib when not in use.
Wave-2 Plus Camera Jib Arm
with 75mm Bowl adapter
Bottom
clamp
Red Spreader
Tripod stand
12V Joystick Controller
with 7.5m wire
Lanc Zoom Controller
with 9m wire
Sr Pan-Tilt Head
Weight Bar with Closer
Portable Dolly
PROAIM 10' Wave-2 Plus Telescopic Jib Arm Crane Film Production Package
3
Assembling 10' Wave-2 Plus Telescopic Jib Arm
You can use the telescopic jib in 2 ways
1. In case of spreader, follow the following steps

Open Tripod spreader. In order to extend legs of spreader, loosen the knob and extend it as
per your requirement and retighten the knob to secure.

Open the legs of 100mm tripod stand then attach it to spreader, lock it in place with the
rubber grips.
2. In case of Dolly, follow the following steps

You will receive your 3-leg dolly collapsed for shipping/storage purposes. Loosen the screw
and extend it as per your requirement and retighten the screw to secure.
PROAIM 10' Wave-2 Plus Telescopic Jib Arm Crane Film Production Package

4
Now mount the Tripod Stand on Dolly, lock it in place with the rubber grips.

Adjust riser height of Tripod by loosening lock controls located on each leg, slide the stand
up to a desired level position and lock leg extensions in place to secure.

Now attach the central fork with the tripod bowl, then attach bottom clamp to secure it
well.
PROAIM 10' Wave-2 Plus Telescopic Jib Arm Crane Film Production Package
5
NOTE It is important to make sure that the Central Fork is seated in the bowl properly. That
means perpendicular to the tripod bowl. Off axis installation may hamper movement of the jib.
Also you may need the assistance of a grip stand to hold the camera end of the arm during
installation preventing it from falling as it will be front heavy at this point. You may also need
the grip stand or assistance at the rear of the jib when mounting the camera.

Unscrew the knob to extend jib arm at back and retighten the knob. Secure all the
connections.

Insert the weight bar into the jib arm.

Now slide in weight to it as per your requirement and screw in weight closer properly.
(Counter weight NOT INCLUDED)
PROAIM 10' Wave-2 Plus Telescopic Jib Arm Crane Film Production Package

Loosen the knobs of Jib arm to extend the front telescopic post of the Jib.

Extend the Jib as per your requirement and tighten all the knobs to secure.
YOUR PROAIM 10' WAVE-2 PLUS TELESCOPIC JIB ARM CRANE
ALL DRESSED UP AND GOOD TO GO
6
PROAIM 10' Wave-2 Plus Telescopic Jib Arm Crane Film Production Package
7
Camera Mounting

Loosen the bolts of Jib bowl & remove the adapter plate. Mount your fluid head set-up onto
the bowl plate and lock it with locking adapter.

Now mount your camera set-up onto fluid head (not included) and secure it with help of
provided knob.
To mount Sr. Pan Tilt Head, follow these steps:

Remove the fluid head mounting bowl by loosening the bolts as shown and then attach the
pan tilt head mounting plate and secure by tightening the bolts.
PROAIM 10' Wave-2 Plus Telescopic Jib Arm Crane Film Production Package



8
Attach the Pan Tilt Head and secure by tightening the bolts. Now mount your camera with
camera mounting screw on Pan Tilt Head.
Mount the Joystick on weight rod & tighten the knob, now attach the one end of XLR Cable
with Joystick.
Now attach the second end of XLR cable
with Pan Tilt Head.
PROAIM 10' Wave-2 Plus Telescopic Jib Arm Crane Film Production Package

Mount the lanc zoom controller on weight rod & tighten the knob, now attach the one end
of 9mtr wire with lanc zoom controller and second end of cable with camera.
LCD Mounting (Not Included)


9
Attach your LCD Mounting Arm to Jib Fork
and tighten it properly to secure.
Now screw in the LCD to arm and tighten
its knob after positioning the angle of LCD
Arm.
YOUR PROAIM 10' WAVE-2 PLUS TELESCOPIC JIB ARM CRANE FILM
PRODUCTION PACKAGE ALL DRESSED UP AND GOOD TO GO
(SHOWN WITH OPTIONAL
ACCESSORIES)
PROAIM 10' Wave-2 Plus Telescopic Jib Arm Crane Film Production Package
10
WARRANTY
We offer a one year warranty for our products from the date of purchase.
We will repair or replace your product, free of charge, in the event of a defect in materials or
craftsmanship obtained during normal use or handling based on the user manual. Please note
that we will not cover any shipping costs for returning the product to us. If any VAT or import
duties are applied to the return, we will also charge these costs to the customer.
The warranty does not include, by the way of example, damage caused by products that we do
not supply or from mishandling in transit, accident, misuse, neglect, lack of care of the
product , or service by anyone other than our company.
We are not liable for incidental or consequential damages resulting from the use of the unit or
occurring due to any breach of this warranty.
Replacement parts of the product will be provided at nominal cost (covering the cost price of the
replacement parts only) to the customers after the Warranty Period has expired. We will cover
the complete cost of sending replacement parts within the warranty period. After that, Nominal
cost of the product & Actual shipping cost will be charged.
Do not send the unit to us without first getting a response and getting the approval to send back
the item.
In case of any kind of dissatisfaction, we urge you to Contact us immediately and we shall do our
best to help you out.
For any other assistance you can reach us via email.