Aeroquip®
Wire Reinforced
Synthetic
Rubber Hose
Assemblies
• Lightweight and Flexible
• Qualified to Industry
Standards
• Integral Abrasion
and Fire Resistance
Covers Available
Aeroquip Wire Reinforced Synthetic Rubber Hose
601/AE701 Hose
Design Features
Construction: Synthetic rubber inner tube with two layers
of stainless steel wire braid reinforcement.
•Flexibility
•Lightweight
Application: Fuel, engine oil, and coolants.
•
Fluid temperatures:
-65°F to +300°F (-54°C to +149°C)
Basic Specification: MIL-H-83797, TSO C53a,Type A.
Integral Abrasion Resistant Cover
AE501 Hose
•
TSO C53a, Type A and Type C
approvals (with fire sleeve)
Construction: 601/AE701 hose overlaid with a blue braided
chafeguard cover of tough polyester yarn.
Application: Fuel, engine oil, and coolants.
Basic Specification: MIL-H-83797, TSO C53a,Type A.
Integral Fire Sleeve
AE401 Hose
Construction: 601/AE701 hose with an integral cover of
silicone rubber compound.
Application: Fuel, engine oil, and coolants.
Basic Specification: MIL-H-83797, TSO C53a,Type C.
•
Mil-Spec Approvals:
• MIL-H-83796/1 through
MIL-H-83796/9 Assemblies
• MIL-H-83797 Hose,
MIL-F-83798 Fittings
•
Available in sizes -3 thru -32
•
vailable with polyester/integral
A
sleeve
•
Field attachable fittings
NOTE: Hose not intended for vacuum application use. See Mil-H-83797.
Hoses that may see intermittent vacuum pressure require an internal
support coil. Contact Eaton for additional information.
End Fitting
Thread
Nut: -3, -4 and -5 steel, AMS 5024 (C1137)
Nut: -6 and up aluminum, AMS 4119 (2024)
Nut Wire: Cres., AMS5685 (305)
Nipple: -3, -4 and -5 steel AMS 5024 (C1137)
Nipple: -6 and up aluminum, AMS4119 (2024)
Elbow: -3, -4 and -5 steel AMS5024
(C1137); -6 and up aluminum, AMS4117 (6061)
Socket: AMS4117 (6061)
All sizes
SizeThread
-3
.375-24 UNJF-3B
-4
.4375-20 UNJF-3B
-5
.500-20 UNJF-3B
-6
.5625-18 UNJF-3B
-8
.750-16 UNJF-3B
-10
.875-14 UNJF-3B
-12
1.0625-12 UNJ-3B
-16
1.3125-12 UNJ-3B
-20
1.625-12 UNJ-3B
-24
1.875-12 UNJ-3B
-32
2.500-12 UNJ-3B
Hose Dimensions and Performance Data
Hose Size
-3
-4
601/AE701 Hose O.D. (Max.)
.398
.462
AE501 Hose O.D. (Max.)
.470
AE401 Hose O.D. (Max.)
Hose I.D. (Min.)
-5
-6
-8
-10
-12
-16 -20
-24
-32
.508
.571
.673
.820
.961
1.187
1.468
1.734
2.140
.530
.575
.659
.761
.895
1.053
1.265
1.526
1.800
2.160
.721
.755
.801
.864
.966
1.112
1.253
1.465
1.726
2.019
2.436
.141
.204
.266
.329
.415
.539
.665
.844
1.094
1.344
1.750
Minimum Bend Radius (inches)
1.75
2.00
2.25
2.50
3.50
4.00
4.50
5.50
8.00
9.00
12.50
Operating Pressure (PSI)
1500
1500
1500
1500
1250
1250
1250
1000
800
400
350
Proof Pressure (PSI)3000
3000
3000
3000
2500
2500
2000
1500
1500
1300
800
600
Minimum Burst Pressure (PSI)
6000
6000
6000
6000
5000
5000
4000
3000
2000
2000
1200
601/AE701 Hose Wt. (Lb./Ft.)
.093
.114
.145
.155
.170
.207
.285
.380
.490
.675
.903
AE501 Hose Wt. (Lb./Ft.)
.122
.138
.172
.184
.204
.248
.333
.439
.636
.920
1.138
AE401 Hose Wt. (Lb./Ft.)
.257
.310
.348
.351
.396
.474
.592
.750
.891
1.229
1.471
All dimensions in inches
2
EATON
Aerospace Group
TF100-4E April 2013 Hose Assembly Part Number Information
Assembly Length
Assembly length is measured from
sealing surface to sealing surface.
When defining the part number
length, measure the length from
end point to end point on flareless
fittings. With elbow fittings, the
measuring point is the intersection
of the centerline of the elbow with
the face of the sealing surface.
Rotation Angle
Measurement
On assemblies with an elbow fitting
on each end, measure the rotation
angle as shown. The index angle will
follow the basic style hose assembly
part number indicated (see example
for “double elbow” assemblies).
In all cases, the angle should be
expressed in 3 digits. For example,
35° should be written as 035. If the
angle desired is 0°, specify 000.
Hose Assemblies
To properly specify the correct hose
assembly, use the simple numbering
system below. Straight and single
elbow assemblies are identified by
the number beginning with AE701
and double elbow assemblies are
identified by a number beginning
with AE70XX. Any assembly can be
ordered using these numbers.
Assembly Length Tolerances
Up to and including 8 inches:
±.125
Above 8 inches, to and including 16 inches:
±.187
Above 16 inches, to and including 24 inches:
±.250
Above 24 inches, to and including 36 inches:
±.312
Above 36 inches, or longer:
±1%
Bulk Hose
Bulk hose will be supplied in 25-foot lengths whenever possible,
but the right is reserved to ship random lengths over 3 feet unless
otherwise specified. Contact your Eaton representative if you have
questions. An additional charge will be made for hose cut to specified lengths.
300 ft., 601/AE701-8
Length (in feet)
Hose number
Size (tube O.D. in 1/16’s)
Examples
Straight and Single Elbow Hose Assemblies
Double Elbow Hose Assemblies
AE701XXXX G0184
AE70XX
Base number for all straight
and single elbow assemblies
Base number for all double
elbow assemblies
Size code (see below)
Size code (see below)
Assembly length, in inches,
always four digits; last digit indicates
fractional length in 1/8’s of an inch
Assembly length, in inches,
always four digits; last digit indicates
fractional length in1/8’s of an inch
Hose Dash Size
3 4 5 6 8 10 12
16 20 24 32
Letter Code
B E F G H J
M
K
N
P
G
0184
-035
Elbow position angle, expressed in three digits
R
EATON
Aerospace Group
TF100-4E April 2013 3
Flared Fitting
Straight
45°
90°
Straight Fitting Dimensions (M83798/1-Size)
Max.
Max.
Hose Fitting Nipple Dim. Dim. Dim. Dim. Dim. Dim. Nut SocketFitting Dim.
SizeP/N P/N AB C DR*H
Hex***
Hex***
Wt.**E
-3 816-3 526-3 1.30.64 .34 .64 –– .103 .58 .562 .049 ––
-4
816-4
526-4
1.33 .65
.37
.70
––
.150
.65
.625
.061
––
-5
816-5
526-5
1.38 .70
.38
.76
––
.211
.72
.688
.078
––
-6
816-6D
526-6D
1.51 .76
.38
.83
––
.274
.80
.750
.046
––
-8
816-8D
526-8D
1.79 .94
.43
1.04
––
.366 1.01 .875
.078
––
-10
816-10D
526-10D
1.94
.99
.50
1.18
––
.472
1.16 1.062
.108
––
-12
816-12D
526-12D
2.01 1.00
.57
1.47
––
.576
1.45 1.188
.168
––
-16
816-16D
526-16D
2.36 1.16
.60
1.76
––
.781
1.74 1.438
.240
––
-20
816-20D
526-20D
2.64 1.34
.64
2.11
––
1.026 2.11 1.750
.372
––
-24
816-24D
526-24D
2.79 1.44
.74
2.47
––
1.264 2.48 1.938
.504
––
-32
816-32D
526-32D
3.16 1.62
.92
3.20
––
1.684 3.20 2.500
.900
––
45° Fitting Dimensions (M83798/2-Size)
-3 8846-3 8746-3 1.741.05
-4
8846-4
8746-4
1.72 1.02
-5
8846-5
8746-5
1.83 1.12
-6
8846-6D
8746-6D
2.00 1.22
-8 8846-8D 8746-8D 2.171.30
-108846-10D8746-10D2.421.44
-128846-12D8746-12D2.791.76
-168846-16D8746-16D3.061.83
-20 8846-20D 8746-20D
3.45 2.13
-24 8846-24D 8746-24D
3.65 2.28
-32 8846-32D 8746-32D
4.26 2.69
.34
.37
.38
.38
.43
.50
.57
.60
.64
.74
.92
.64 .375 .103 .58 .562 .056 .376
.70
.375 .150
.65
.625
.070
.352
.76
.438 .211
.72
.688
.091
.415
.83
.500 .274
.80
.750
.052
.446
.98 .500.3661.01 .875 .085 .457
1.17.625.4721.161.062 .119 .537
1.30.844.5761.451.188 .179 .623
1.55.969.7811.741.438 .255 .659
1.91 1.188 1.026 2.11 1.750
.376
.768
2.11 1.375 1.264 2.48 1.938
.506
.867
2.72 1.750 1.684 3.20 2.500
.8911.065
.34
.37
.38
.38
.43
.50
.57
.60
.64
.74
.92
.64 .375.103 .58 .562 .057 .752
.70
.375 .150
.65
.625
.071
.718
.76
.438 .211
.72
.688
.094
.844
.83
.500 .274
.80
.750
.053
.922
.98 .500.3661.01 .875 .088 .938
1.17.625.4721.161.062 .124 1.126
1.30.844.5761.451.188 .189 1.376
1.55.969.7811.741.438 .267 1.500
1.91 1.188 1.026 2.11 1.750
.399
1.782
2.11 1.375 1.264 2.48 1.938
.538
2.032
2.72 1.750 1.684 3.20 2.500
.953
2.532
90° Fitting Dimensions (M83798/3-Size)
-3 8891-3 8791-3 1.58.89
-4
8891-4
8791-4
1.59 .89
-5
8891-5
8791-5
1.68 .96
-6
8891-6D
8791-6D
1.85 1.07
-8 8891-8D 8791-8D 2.011.14
-108891-10D8791-10D2.251.27
-128891-12D8791-12D2.661.63
-168891-16D8791-16D2.971.74
-20 8891-20D 8791-20D
3.38 2.06
-24 8891-24D 8791-24D
3.59 2.22
-32 8891-32D 8791-32D
4.22 2.65
All dimensions in inches
DIM. B = Hose cut factor.
DIM. E = Nominal drop dimensions. Tolerance is ±.035" on bent tube fittings.
*R = Radius of elbow measured to centerline.
**Weight = Nipple assembly plus socket (nominal).
*** = Distance across corners.
4
EATON
Aerospace Group
TF100-4E April 2013 Socket P/N 516-XXD
Hose Assembly/Swivel Flared to Swivel Flared
Configurations
601/AE701
AE501
AE401
Hose
Hose
Hose
Hose
Assembly
Assembly
Assembly
Size
Base No.
Base No.
Base No.
601/AE701
W/AE102
Firesleeves
Hose Assembly
Base No.
straight to straight
-3 thru-32
AE7010000
AE7013110
AE7013106
AE7010001
-3 thru-32
AE7010100
AE7013111
AE7013107
AE7010101
-3 thru-32
AE7010200
AE7013112
AE7013131
AE7010201
-3 thru-32
AE7000
AE7058
AE7074
AE7001
-3 thru-32
AE7012
AE7059
AE7075
AE7013
-3 thru-32
AE7027
AE7060
AE7076
AE7028
straight to 45° elbow
straight to 90° elbow
45° elbow to 45° elbow
45° elbow to 90° elbow
90° elbow to 90° elbow
EATON
Aerospace Group
TF100-4E April 2013 5
Flareless Fitting
Straight
45°
90°
Straight Fitting Dimensions (M83798/4-Size)
Hose Fitting
SizeP/N
-3 826-3
-4
826-4
-5
826-5
-6
826-6D
-8
826-8D
-10
826-10D
-12
826-12D
-16
826-16D
-20
826-20D
-24
826-24D
-32 ––
Nipple Dim. Dim. Dim. Dim. Dim. Dim. Nut SocketFitting Dim.
P/N AB C DR*H
Hex***
Hex***
Wt.**E
536-3 1.52.85 .13 .64 –– .103 .58 .640 .051 ––
536-4
1.48 .80
.22
.70
––
.150 .654 .703
.064
––
536-5
1.54 .86
.23
.76
––
.211
.72
.765
.080
––
536-6D
1.71 .96
.19
.83
––
.274 .798 .827
.048
––
536-8D
2.02 1.17
.21
1.04
––
.366 1.014 .984
.082
––
536-10D
2.22 1.26
.24
1.18
––
.472 1.158 1.171
.115
––
536-12D
2.28 1.27
.31
1.47
––
.576 1.447 1.296
.175
––
536-16D
2.64 1.44
.32
1.76
––
.781 1.736 1.546
.254
––
536-20D
2.92 1.62
.37
2.11
––
1.026 2.111 1.906
.368
––
536-24D
3.19 1.85
.33
2.47
––
1.264 2.477 2.109
.544
––
–– –––– –––––––––– –– –– ––
45° Fitting Dimensions (M83798/5-Size)
-3 ––
––
-4
880112-4 885112-4
-5 ––
––
-6 880112-6D 885112-6D
-8 880112-8D 885112-8D
-10 880112-10D 885112-10D
-12 880112-12D 885112-12D
-16 880112-16D 885112-16D
-20 880112-20D 885112-20D
-24 ––
––
-32 ––
––
–––– –––––––––– –– –– ––
1.72 1.1
.22
.70
.25
.150 .654 .703
.070
.452
–––– –––––––––– –– –– ––
2.03 1.36
.19
.83
.50
.274 .798 .827
.054
.578
2.32 1.45
.21
.98
.50
.366 1.014 .984
.088
.610
2.61 1.63
.24
1.17
.62
.472 1.158 1.171
.125
.725
2.97 1.93
.31
1.30
.84
.576 1.447 1.296
.189
.800
3.25 2.03
.32
1.55
.97
.781 1.736 1.546
.270
.854
3.65 2.33
.37
1.91
1.19 1.026 2.111 1.906
.408
.962
–––– –––––––––– –– –– ––
–––– –––––––––– –– –– ––
90° Fitting Dimensions (M83798/6-Size)
-3 ––
––
-4
880114-4 885114-4
-5
880114-5 885114-5
-6 880114-6D 885114-6D
-8 880114-8D 885114-8D
-10 880114-10D 885114-10D
-12 880114-12D 885114-12D
-16 880114-16D 885114-16D
-20 880114-20D 885114-20D
-24 ––
––
-32 ––
––
–––– –––––––––– –– –– ––
1.59 .89
.22
.70
.25
.150 .654 .703
.070
.860
1.68 .96
.23
.76
.31
.211 .720 .765
.071
1.000
1.85 1.07
.19
.83
.50
.274 .798 .827
.057
1.112
2.01 1.14
.21
.98
.50
.366 1.014 .984
.092
1.156
2.25 1.27
.24
1.17
.62
.472 1.158 1.171
.130
1.392
2.66 1.63
.31
1.30
.84
.576 1.447 1.296
.199
1.626
2.97 1.74
.32
1.55
.97
.781 1.736 1.546
.282
1.776
3.38 2.06
.37
1.91
1.19 1.026 2.111 1.906
.431
2.056
–––– –––––––––– –– –– ––
–––– –––––––––– –– –– ––
All dimensions in inches
DIM. B = Hose cut factor.
DIM. E = Nominal drop dimensions. Tolerance is ±.035" on bent tube fittings.
*R = Radius of elbow measured to centerline.
**Weight = Nipple assembly plus socket (nominal).
*** = Distance across corners.
6
EATON
Aerospace Group
TF100-4E April 2013 Socket P/N 516-XXD
Hose Assembly/Swivel Flareless to Swivel Flareless
Configurations
601/AE701
AE501
AE401
Hose
Hose
Hose
Hose
Assembly
Assembly
Assembly
Size
Base No.
Base No.
Base No.
601/AE701
w/AS1072
Firesleeves
Hose Assembly
Base No.
straight to straight
-3 thru-32
AE7010010
AE7013121
AE7013132
AE7010011
-3 thru-32
AE7010110
AE7013123
AE7013133
AE7010111
-3 thru-32
AE7010210
AE7013125
AE7013134
AE7010211
-3 thru-32
AE7003
AE7066
AE7077
AE7004
-3 thru-32
AE7015
AE7068
AE7078
AE7016
-3 thru-32
AE7030
AE7070
AE7079
AE7031
straight to 45° elbow
straight to 90° elbow
45° elbow to 45° elbow
45° elbow to 90° elbow
90° elbow to 90° elbow
EATON
Aerospace Group
TF100-4E April 2013 7
Flanged Fitting
Straight
45°
90°
Straight Fitting Dimensions (M83798/7-Size)
Max.
Max.
HoseFitting NippleDim.Dim.Dim.Dim.Dim.Dim.Socket
FittingDim.
Size
P/N P/N AB C DR*H
Hex***
Wt.**E
-3 –– –– –––––––––––––––– ––
-4 –– –– –––––––––––––––– ––
-5 –– –– –––––––––––––––– ––
-6 –– –– –––––––––––––––– ––
-8
8844-8D
8714-8D
1.97.84 ––.980––.355.875.089 ––
-10
8844-10D
8714-10D
2.08.87 ––1.170–– .4721.062.114 ––
-12
8844-12D
8714-12D
2.291.25 ––1.296–– .5761.188.153 ––
-16
8844-16D
8714-16D
2.531.30 ––1.546–– .7811.438.206 ––
-20
8844-20D
8714-20D
2.831.50 ––1.906––1.0261.750.316 ––
-24
8844-24D
8714-24D
2.711.34 ––2.109––1.2641.938.364 ––
-32
8844-32D
8714-32D
3.081.52 ––2.718––1.6842.500.646 ––
45° Fitting Dimensions (M83798/8-Size)
-3 –– –– –––––––––––––––– ––
-4 –– –– –––––––––––––––– ––
-5 –– –– –––––––––––––––– ––
-6 –– –– –––––––––––––––– ––
-88845-8D8745-8D.2081.18 –– .980.500.360.875.088 .338
-10 8845-10D 8745-10D
.226
1.28
––
1.170
.625
.472
1.063
.113
.375
-12 8845-12D 8745-12D
2.64
1.60
––
1.296
.844
.576
1.188
.157
.468
-16 8845-16D 8745-16D
2.90
1.68
––
1.546
.969
.781
1.438
.208
.505
-208845-20D8745-20D3.25 1.93 –– 1.9061.1881.0261.750 .321 .569
-248845-24D8745-24D3.40 2.03 –– 2.1091.3751.2641.938 .386 .625
-328845-32D8745-32D3.92 2.36 –– 2.7181.7501.6842.500 .672 .734
90° Fitting Dimensions (M83798/9-Size)
-3 –– –– –––––––––––––––– ––
-4 –– –– –––––––––––––––– ––
-5 –– –– –––––––––––––––– ––
-6 –– –– –––––––––––––––– ––
-88890-8D8790-8D2.351.48 –– .980.500.360.875.097 .892
-10 8890-10D 8790-10D
2.51
1.53
––
1.170
.625
.484
1.063
1.123
.896
-12 8890-12D 8790-12D
2.66
1.63
––
1.296
.844
.576
1.188
.164
1.156
-16 8890-16D 8790-16D
2.97
1.74
––
1.546
.969
.781
1.438
.222
1.282
-208890-20D8790-20D3.38 2.06 –– 1.9061.1881.0261.750 .344 1.500
-248890-24D8790-24D3.54 2.22 –– 2.1091.3751.2641.938 .448 1.688
-328890-32D8790-32D4.21 2.65 –– 2.7181.7501.6842.500 .732 2.062
All dimensions in inches
DIM. B = Hose cut factor.
DIM. E = Nominal drop dimensions. Tolerance is ±.035" on bent tube fittings.
*R = Radius of elbow measured to centerline.
**Weight = Nipple assembly plus socket (nominal).
*** = Distance across corners.
8
EATON
Aerospace Group
TF100-4E April 2013 Socket P/N 516-XXD
Hose Assembly/4-Hole Flange to 4-Hole Flange
Configurations
601/AE701
Hose
Hose
Assembly
Size
Base No.
601/AE701
w/AS1072
Firesleeves
Hose Assembly
Base No.
straight to straight
-8 thru-32
AE7010020
AE7010021
-8 thru-32
AE7010120
AE7010121
-8 thru-32
AE7010220
AE7010221
-8 thru-32
AE7006
AE7007
-8 thru-32
AE7018
AE7019
-8 thru-32
AE7033
AE7034
straight to 45° elbow
straight to 90° elbow
45° elbow to 45° elbow
45° elbow to 90° elbow
90° elbow to 90° elbow
EATON
Aerospace Group
TF100-4E April 2013 9
How to Assemble 601/AE701 Hose Assemblies with
“little gem” Straight Fittings and Elbows
Straight Fittings
To make hose assembly of length
“L”, cut hose to length “J”. Obtain
“J” length by subtracting proper
fitting allowances. See “B”
dimensions on fitting pages.
Step 1.
Step 3.
Step 5.
Step 6.
Cut hose squarely to length. Use
hose cut-off machine or fine tooth
hacksaw. To minimize wire braid
flare-out, wrap hose with masking
tape and saw through tape.
Remove tape before step 2.
Important – mark hose position
around hose at rear of socket.
Use a grease pencil, painted line
or tape.
Carefully insert nipple and engage
nipple and socket threads while
holding hose in position with
other hand. Make sure that hose
does not push out of socket by
observing mark made in step 3.
Complete assembly using wrench
while continuing to hold in
position. Maximum allowable gap
is .041 inches in sizes 3, 4 and 5,
and .031 inches in size 6 and up.
Step 2.
Insert hose in socket with a
twisting, pushing motion until
hose is in line with back of socket
threads.
Step 4.
Step 7.
Lubricate inside of hose and
nipple threads liberally. Use SAE30
lubricating oil. Avoid getting oil in
the cutting spur of the nipple.
IMPORTANT – check for hose
push-out by observing hose
position mark. None should be
evident. Clean, inspect and proof
test.
Note: Hose push-out after proof test should not exceed 1/32 inch or size 12 and up. None is allowable on smaller sizes.
Elbow Fittings
Step 1.
Step 4.
Step 5.
Step 6.
Follow through steps 1, 2, and 3,
above.
Carefully insert nipple and engage
nipple and socket threads while
holding hose in position with other
hand. Make sure hose does not
push out of socket by observing
mark.
Complete assembly using wrench
on elbow hex while continuing to
hold hose in position. Tighten until
hex is snug against socket. On
forged elbow, use wrench on forging
flats. Tighten until shoulder is snug
against socket.
Adjustments may be necessary to
obtain the desired position angle
between two elbows. In order to
minimize backing off elbows to
position, the following procedure
should supplement step 5:
Step 2.
Flange elbow fittings. Drop flange
over threaded end of nipple. Nipple
shoulder must fit into counterbore
of flange.
Step 3.
a. Tighten both elbows to within .031 inches of socket then start to position for relative angle between elbows.
b.Finish assembly by adjusting both elbows. Backing-off to position should be avoided and in no case should exceed 1/4 turn. Maximum allowable gap between hex and socket is .031 inches.
Lubricate inside of hose and
nipple threads liberally. Use SAE30
lubricating oil. Avoid getting oil in the
cutting spur of the nipple.
Step 7.
Note: Hose push-out after proof test should not exceed 1/32 inch on sizes 12 and up.
None is allowable on smaller sizes.
10
EATON
Aerospace Group
TF100-4E April 2013 IMPORTANT – check for hose
push-out. See step 6 above. Clean,
inspect and proof test.
Testing and Storage of Flexible Hose Lines
Shield
Clean
Proof Test/Fluid
Inspect
Clean, Inspect, Proof Test
CLEAN…Clean hose after
cutting to length. Be sure all
cutting residue is dislodged.
After assembly, clean each hose
assembly internally using clean,
dry compressed air.
INSPECT…Examine hose assembly
internally for cut or bulged inner
tube, obstructions and cleanliness.
Examine Aeroquip hose assemblies
with “little gem” fittings for hose
push-out. Inspect for proper gap
between nut and socket or hex and
socket. Nuts should swivel freely.
PROOF TEST…Test hose
assemblies in straight, horizontal
position and observe for evidence
of leakage while maintaining test
pressure. Several hose assemblies
may be tested at one time by
connecting them in series.
!
1.LIQUID TEST MEDIUM… tighten cap only after all trapped air has bled from assembly. Use a heavy plastic protective cover when applying pressure.
2.Use proper proof-test fluid specified for hose:
3.Drain and cap.
4.Corrosion protection of fittings
on hose assemblies.
a. Brass, corrosion resistant steel, and aluminum alloy fittings require no additonal treatment.
b. Fittings on air or instrument hose assemblies should not be oiled. Dry thoroughly and cap with oil and grease-free caps.
Storage and Handling
1. BULK HOSE AND HOSE ASSEMBLIES…hose should be stored away from sunlight, heat, ozone, etc. To minimize obsolescence or deterioration of hose in storage, follow “first-in, first-out” principle in releasing stock for production or shipment.
2.Short hose lengths or assemblies may be conveniently stored in closed containers to protect from dust. Other hose assemblies should have the ends capped. Hose assemblies made up in the field should be marked with the date of assembly before being placed in storage.
NOTE: All hose assemblies taken
from storage should be prooftested prior to installation in
aircraft.
Type
Hose No.
Pneumatic
fuel, oil and coolant
601/AE701
Proof Test Fluid
Hydraulic oil
(MIL-H-5606)* or
water
*Flush after proof-testing using oleum or other neutral spirits.
WARNING
FAILURE OR IMPROPER
SELECTION,USE, OR ASSEMBLY OF THE PRODUCTS AND
COMPONENTS FOR APPLICATIONS
DESCRIBED HEREIN CAN RESULT
IN POSSIBLE PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.
This document and any other related
information from Eaton® Aeroquip®
or its affiliates and authorized
distributors, provide product options
for consideration by Users having
technical expertise with these
products. Due to the wide variety of
applications and operating conditions
for these products and components,
the User is solely responsible for
making the final selection of the
products and ensuring that all
performance, safety and warning
requirements for the User's
intended application are met.
Eaton Aeroquip recommends that
Eaton® Aeroquip® hose, fittings
or assembly equipment must
be used only with other Eaton®
Aeroquip® hose, fittings or assembly
equipment,and Eaton Aeroquip and/
or its affiliates disclaim any obligation
or liability (including all incidental
and consequential damages)to the
extent Eaton® Aeroquip® hose,
fittings or assembly equipment is
used with any other manufacturer's
hose, fittings or assembly equipment
or in the event that Eaton Aeroquip
recommended processes and
product instructions for hose
assemblies are not followed.
The products described herein,
including product features,
specifications, designs, and
availability are subject to change at
any time without notice.
The Company retains the right to amend, change or modify any data in this document at any time.
EATON
Aerospace Group
TF100-4E April 2013 11
Eaton
Aerospace Group
Fluid & Electrical Distribution Division
300 South East Avenue
Jackson, Michigan 49203-1972
Phone: (517) 787 8121
Fax: (517) 789 2947
Eaton
Aerospace Group
9650 Jeronimo Road
Irvine, California 92618
Phone: (949) 452 9500
Fax: (949) 452 9555
www.eaton.com/aerospace
Copyright © 2013 Eaton
All Rights Reserved
Copying or Editing is Forbidden
Form No. TF100-4E
April 2013