Base Angle Technical Datasheet
Description
Base Angles are L-shaped, non-load bearing light gauge structural steel elements that constitute the horizontal
bottom support to which the vertical Z-Z-Studs are screw-fixed. They also serve as vertical supports for angle
junctions in this system. Base Angles are fixed to the concrete floor by means of bottom KDM/L Anchors at 600 mm
centers. Both the flanges of the ZZ Studs are fastened from the Base Angle into the ZZ Stud with Hex Head Screws.
Primary Data
Drywall Product
Base Angle
Drywall System
Applicable for Cinema System & Partition System
Coating
G90 or Equivalent
Material
Galvanized Steel
Standard Compliance
ASTM C 645 & ASTM C 653
Technical Data
Thickness
(mm)
Width
(mm)
2.5 – 4.0
50 x 50
60 x 60
75 x 75
Doc/PDS/MC/BA/12/R0
C Stud Technical Datasheet
Description
The C Studs are the vertical framings used for Partition and Liner Systems with a friction fit between bottom and top
tracks. The C Studs have exceptional coatings that prevents it from gradually rusting overtime. They are very easy to
install and can be tailored in accordance to a project's requirements. They are specially designed to accept for one
layer and multi layer Gypsum Plasterboards.
Primary Data
Drywall Product
C Stud
Drywall System
Applicable for Partition & Liner Systems
Standard Length (mm)
3000 (Other lengths available on request)
Coating
AZ150 Zinc- Aluminium Alloy
Steel Grade
G300
Min. Yield Strength: 300 Mpa
Min. Tensile Strength: 340 Mpa
Material
Galvanized Steel
Technical Data
Thickness
(mm)
Width
(mm)
Length
(mm)
Flange
(mm)
0.55
51,64,70
3000
33.5 / 35.5
0.60
51,64,70,76,92,100
3000
33.5 / 35.5
0.80
51,64,70,76,92,100,125,150
3000
33.5 / 35.5
0.90
51,64,70,76,92,100,125,150
3000
33.5 / 35.5
Doc/PDS/MC/CS/12/R0
CH Stud Technical Datasheet
Description
The CH Studs are specially designed for Shaftwall Systems, whereby access is only via one side, such as those
commonly found in lift shafts, stairways and garbage shoots. The CH Studs are designed to provide friction-fit
contact for 25 mm Gypsemna's Core Board as shaft liner. CH Studs normally space at every 600 mm to suit the width
of the Gypsemna's Core Board panel.
Primary Data
Drywall Product
CH Stud
Drywall System
Applicable for Shaftwall Systems
Standard Length (mm)
3600 (Other lengths available on request)
Coating
Z180 Zinc Coating
Steel Grade
G2
Min. Yield Strength: 270 Mpa
Min. Tensile Strength: 330 Mpa
Material
Galvanized Steel
Technical Data
Part No.
Thickness
(mm)
Width
(mm)
Length
(mm)
PN570, PN590
0.55
64,102
3600
PN572, PN592
0.90
64,102
3600
6mm
6mm
6mm
6mm
Doc/PDS/MC/CHS/12/R0
Deflection Head Track Technical Datasheet
Description
The Deflection Head Track allows a vertical movement from the ceiling/ roof. This vertical deflection prevents loads
from being transferred to the studs.
Primary Data
Drywall Product
Deflection Head Track
Drywall System
Applicable for Partition & Cinema Systems
Standard Length (mm)
3000 (Other lengths available on request)
Coating
AZ150 Zinc- Aluminium Coating
Steel Grade
G300
Min. Yield Strength: 300 Mpa
Min. Tensile Strength: 340 Mpa
Material
Galvanized Steel
Technical Data
Thickness
(mm)
Length
(mm)
Width
(mm)
Flange
(mm)
0.80
3000
51,64,70,76,92,100,125,150
50
0.90
3000
51,64,70,76,92,100,125,150
50
Doc/PDS/MC/DHT/12/R0
E Stud Technical Datasheet
Description
The E Studs are extremely light in weight and are used for starter studs, intersections, door openings and end studs.
A 25 mm gaps between the flange allows friction- fit contact for the 25 mm Gypsemna's Core Board as shaft liner.
Primary Data
Drywall Product
E Stud
Drywall System
Applicable for Shaftwall Systems
Standard Length (mm)
3000 (Other lengths available on request)
Coating
AZ150 Zinc Coating
Steel Grade
G2
Min. Yield Strength: 270Mpa
Min. Tensile Strength: 330 Mpa
Material
Galvanized Steel
Technical Data
Part No.
Thickness
(mm)
Width
(mm)
Length
(mm)
PN574/594
0.55
64,102
3600
6mm / 10mm (for 102 E-Stud)
6mm
Doc/PDS/MC/ES/12/R0
Fixing Channel Technical Datasheet
Description
The Fixing Channels are the horizontal member of the partition metal framework. This is used primarily to back up
horizontal cut joints, and also as noggins and to provide support for hanging heavy supports.
Primary Data
Drywall Product
Fixing Channel
Drywall System
Applicable for Shaftwall & Liner Systems
Standard Length (mm)
3000 (Other lengths available on request)
Coating
Z275 Zinc Coating
Material
Galvanized Steel
Standard Compliance
ASTM C645 & ASTM C653
Technical Data
Thickness
(mm)
Width
(mm)
Length
(mm)
Flange
(mm)
0.70
72
3000
10
Doc/PDS/MC/FC/12/R0
Flexible Track Technical Datasheet
Description
When constructing curved walls, stud centers should be reduced to suit the respective lining board. The Flexible
Tracks at the top and bottom are curved to match the specified radius and fastened to the structure through the
holes provided in the web.
Primary Data
Drywall Product
Flexible Track
Drywall System
Applicable for Partition & Liner Systems
Coating
Z275 Zinc Coating
Steel Grade
G2
Min. Yield Strength: 270 Mpa
Min. Tensile Strength: 330 Mpa
Material
Galvanized Steel
Technical Data
Part No.
Type
Width
(mm)
Length
(mm)
PN103, PN104,
PN105, PN106
Flexible Track
51, 64, 76, 92
3000
PN107, PN108,
PN109, PN110
Deflection Head
Flexible Track
64, 76, 92, 150
3000
Doc/PDS/MC/FT/12/R0
Furring Channel Track Technical Datasheet
Description
Furring Channel Track sections provide a friction for furring channels, which not only hold the furring channel in
position until the board is fitted, but also provides a slip joint to allow movement within structure.
Primary Data
Drywall Product
Furring Channel Track
Drywall System
Applicable for Ceiling Systems
Standard Length (mm)
3000 (Other lengths available on request)
Coating
AZ150 Zinc- Aluminium Coating
Steel Grade
G300
Min. Yield Strength: 300 Mpa
Min. Tensile Strength: 340 Mpa
Material
Galvanized Steel
Technical Data
Thickness
(mm)
Length
(mm)
0.55
3000
13
20
0.55
28
30
PN.140 Sectional Profile
28
0.55
16
26
16
PN.142 Sectional Profile
Doc/PDS/MC/FCT/12/R0
J Runner- DHT Technical Datasheet
Description
J Runner- Deflection Head Track (DHT) is commonly used as a wall track for the top fixing of the Shaftwall System.
The sections provide a friction fit for the stud and also provide a slip joint to allow any movement of the structure.
Primary Data
Drywall Product
J Runner- Deflection Head Track (DHT)
Drywall System
Applicable for Shaftwall Systems
Standard Length (mm)
3000 (Other lengths available on request)
Coating
Z180 Zinc Coating
Steel Grade
G2
Min. Yield Strength: 270 Mpa
Min. Tensile Strength: 330 Mpa
Material
Galvanized Steel
Technical Data
Part No.
Thickness
(mm)
Width
(mm)
Length
(mm)
Flange
(mm)
PN575 / 599
0.80
64 & 102
3000
75 x 50
Doc/PDS/MC/JRDHT/12/R0
Conventional Furring Channel Technical Datasheet
Description
Conventional Furring Channel is the secondary member for ceiling metal framework. This is fixed to the main
channel with Wafer head screws through the flange. The gypsum boards are screwed to furring channel.
Primary Data
Drywall Product
Conventional Furring Channel
Drywall System
Applicable for Conventional Ceiling and
Cinema System
Standard Length (mm)
3000 (Other lengths available on request)
Coating
AZ150 Zinc- Aluminium Alloy
Material
Galvanized Steel
Technical Data
Thickness
(mm)
Width
(mm)
Length
(mm)
0.55
70 x 35 x 22
3000
0.70
70 x 35 x 22
3000
Doc/PDS/MC/CFC/12/R0
J Runner Wall Track Technical Datasheet
Description
J Runner Wall Track is commonly used as a wall track for the bottom fixing of the Shaftwall System. Track sections
are normally 3000 mm in length and should be fixed at not more than 600 mm centers.
Primary Data
Drywall Product
J Runner Wall Track
Drywall System
Applicable for Shaftwall Systems
Standard Length (mm)
3000 (Other lengths available on request)
Coating
Z180 Zinc Coating
Steel Grade
G2
Min. Yield Strength: 270 Mpa
Min. Tensile Strength: 330 Mpa
Material
Galvanized Steel
Technical Data
Part No.
Thickness
(mm)
Width
(mm)
Length
(mm)
Flange
(mm)
578/ 598
0.80
64 & 102
3000
57 x 25
Doc/PDS/MC/JRWT/12/R0
Main Channel Technical Datasheet
Description
Main Channel sections are cold roll formed from zinc coated steel strip is the primary member ( carrying Channel )
for Conventional Ceiling metal framework. This is suspended from the roof with wire hanger, adjustment clip and
channel hanger.
Primary Data
Drywall Product
Main Channel
Drywall System
Applicable for Conventional Ceiling & Cinema
Systems
Standard Length (mm)
3000 (Other lengths available on request)
Coating
Z180 Zinc Coating
Standard Compliance
ASTM C 645 & ASTM C 653
Material
Galvanized Steel
Technical Data
Thickness
(mm)
Width
(mm)
Length
(mm)
0.55
38 x 12 x 12
3000
0.70
38 x 12 x 12
3000
1.0
45/60 x 12 x 12
3000
1.2
45/60 x 12 x 12
3000
1.5
45/60 x 12 x 12
3000
Doc/PDS/MC/MC/12/R0
Noggin Track Technical Datasheet
Description
Noggin Tracks are designed to provide support to the wall studs & should be screwed to both flanges of the studs. It
is produced as a continuous noggin track which can be fitted to the stud framing in one length, or individual noggins
may be cut from the track. Noggin track is produced in Various centered cut sections to suit all stud framed wall
installations. Where services are to be fitted and a recessed noggin is required this may be cut from stud or track.
Primary Data
Drywall Product
Noggin Track
Drywall System
Applicable for Partition, Liner & Cinema System
Coating
AZ150 Zinc-Aluminium Alloy
Steel Grade
G300
Min. Yield Strength: 300 Mpa
Min. Tensile Strength: 340 Mpa
Material
Galvanized Steel
Technical Data
Thickness
(mm)
Width
(mm)
Length
(mm)
Stud Spacing
Flange
(mm)
0.80
51,64,70,76,92,100,
125,150
3600
300, 400, 600
32
51, 64, 76, 92 & 150mm
32.0
Doc/PDS/MC/NT/12/R0
Quiet Stud Technical Datasheet
Description
The unique design of the Quiet Stud (together with Gypsemna's lining board), forms an effective buffer against
unwanted noise to provide a simple and cost- effective acoustic solution for inter-tenancy walls in any environment
that requires a practical and dependable acoustic solution between dividing walls.
Primary Data
Drywall Product
Quiet Stud
Drywall System
Applicable for Partition & Liner System
Coating
Z180 Zinc Coating
Steel Grade
G2
Min. Yield Strength: 270 Mpa
Min. Tensile Strength: 330 Mpa
Material
Galvanized Steel
Technical Data
Part No.
Thickness
(mm)
Width
(mm)
Length
(mm)
RQST
0.60
92 x 45
3000
Doc/PDS/MC/QS/12/R0
Furring Channel Technical Datasheet
Description
Furring Channel sections are cold roll formed from zinc coated steel strip is the secondary member for ceiling metal
framework. Furring Channels are connected with Top Cross Rails by using Locking Key joiners. The gypsum boards
are screwed to furring channel. For additional loads consult the manufacturer.
Primary Data
Drywall Product
Furring Channel
Drywall System
Applicable for Ceiling System
Coating
AZ150 Zinc –Aluminium Coating
Steel Grade
G300
Min. Yield Strength: 300 Mpa
Min. Tensile Strength: 340 Mpa
Material
Galvanized Steel
Technical Data
Part No.
Depth
(mm)
Width
(mm)
Length
(mm)
PN308
16
0.55
4800
PB129
28
0.55
4800
Doc/PDS/MC/FC/12/R0
Top Cross Rail Technical Datasheet
Description
The Top Cross Rails are a primary component of the Keylock Ceiling System that allow a friction fit system to
assemble frames for a stronger, more compact, lighter and non- load bearing boards.
Primary Data
Drywall Product
Top Cross Rail
Drywall System
Applicable for Keylock Ceiling System
Coating
AZ150 Zinc- Aluminium Alloy
Steel Grade
G300
Min. Yield Strength: 300 Mpa
Min. Tensile Strength: 340 Mpa
Material
Galvanized Steel
Technical Data
Part No.
Depth
(mm)
Thickness
(mm)
Length
(mm)
PN125, PN127
25
0.60, 0.80
4800
PN128
38
0.80
4800
PN. 125
PN. 127
PN. 128
Doc/PDS/MC/TCR/12/R0
U Track Technical Datasheet
Description
Track sections provide a friction for the studs, which not only holds the studs in position until the lining board is
fitted, but also provides a slip joint to allow for movement in the structure.
Primary Data
Drywall Product
U Track
Drywall System
Applicable for Partition System
Coating
AZ150 Zinc- Aluminium Alloy
Steel Grade
G300
Min. Yield Strength: 300 Mpa
Min. Tensile Strength: 340 Mpa
Material
Galvanized Steel
Technical Data
Thickness
(mm)
Width
(mm)
Length
(mm)
Flange
(mm)
0.55
51, 64, 70
3000
32
0.60
51,64,70,76,92,100
3000
32
0.80
51,64,70,76,92,100
3000
32
0.90
51,64,70,76,92,100
3000
32
Doc/PDS/MC/UT/12/R0
Wall Angle Technical Datasheet
Description
Gypsemna Wall Angle is the perimeter member for ceiling metal framework. This is fixed to the wall.
Primary Data
Drywall Product
Wall Angle
Drywall System
Applicable for Conventional Ceiling System
Coating
Z180/ Z275 Zinc Coating
Standard Compliance
ASTM C 645 & ASTM C 653
Material
Galvanized Steel
Technical Data
Thickness
(mm)
Width
(mm)
Length
(mm)
0.55
25 x 25
3000
0.70
25 x 25
3000
Doc/PDS/MC/WA/12/R0
ZZ Purlins Technical Datasheet
Description
The ZZ Purlins is an assembly made from Z-shaped purlin-sections, roll-formed from high yield galvanized tensile
steel. They serve as non-load bearing structural elements of the ZZ Purlins wall system in compliance with limitheights vs. sections and stud-centre’s. The ZZ Purlins are assembled on the ground and the overlapping flanges
screw-fixed (Hex Head Screws-DP). It is then fastened in upright position to the base-angle on the bottom and on
top to the appropriate Head Bracket, slotted or dampened, that is fastened to the structure by KDML-Anchors if
concrete and welded, bolted or shot if it is to steel.
Primary Data
Drywall Product
ZZ Purlins
Drywall System
Applicable for Partition and Cinema Systems
Coating
Z275 Zinc Coating
Steel Grade
G90
Material
Galvanized Steel
Technical Data
Thickness
(mm)
Width
(mm)
1.5
150, 200, 250
2.0
150, 200, 250
2.5
150, 200, 250
Doc/PDS/MC/ZZP/12/R0
L Angle Technical Datasheet
Description
L Angle is the perimeter member for partition & ceiling metal framework. Used for lateral bracing and other
structural strengthening applications.
Primary Data
Drywall Product
L Angle
Drywall System
Applicable for Partition, Liner and Cinema
Systems
Coating
AZ150 Zinc- Aluminium Alloy
Steel Grade
G300
Min. Yield Strength: 300 Mpa
Min. Tensile Strength: 340 Mpa
Material
Galvanized Steel
Technical Data
Part No.
Width
(mm)
Thickness
(mm)
Length
(mm)
552
25 x 25
0.80
3000
553
35 x 35
0.80
3000
554
50 x 50
0.80
3000
50, 25, 35
0.75
25, 35, 50
50, 25, 35
Sectional Profile
Doc/PDS/MC/LA/12/R0
Resilient Furring Channel Technical Datasheet
Description
Designed for use as a sound isolating system to reduce sound transmission.
Primary Data
Drywall Product
Resilient Furring Channel
Drywall System
Applicable for Partition & Liner Systems
Coating
Z275 Zinc Coating
Steel Grade
G2
Min. Yield Strength: 270 Mpa
Min. Tensile Strength: 330 Mpa
Material
Galvanized Steel
Technical Data
Part No.
Thickness
(mm)
Length
(mm)
PN581
0.55
3600
100.0
40.0
69.0
16.0
Doc/PDS/MC/RFC/12/R0
Expanded Metal Mesh Technical Datasheet
Description
The Expanded Metal Mesh is a type of metal lath having an open mesh formed by slitting galvanized metal sheet as
per specifications and exerting a cross-wise traction resulting in an irregular surface. As part of Gypsemna's Security
wall it is fastened between the boards on each side of the core structure in multiple layer systems and between the
studs / under the boards in single layer systems.
Primary Data
Drywall Product
Expanded Metal Mesh
Drywall System
Applicable for Burglar Partition Systems
Coating
Z275 Zinc Coating
Steel Grade
G275
Standard Compliance
ASTM A 653M: 97
Material
Galvanized Steel
Technical Data
Weight
(Kg/M2)
Dimension
(mm)
1.63 & 1.41
600 x 2440
Doc/PDS/MC/EMM/12/R0