All in One
Flower Box
Flower Side Panel x 4
Top x 4
1.
Cut the files in the quantities stated above.
2.
Glue together the Flower Side Panels using the long side tabs to make the box shape.
3.
Tuck the rounded tabs on the bottom of the Flower Side Panel pieces inside the box and glue them down to fix.
4.
Using the Top Pieces, mountain fold along the outer score lines and valley fold along the middle score line.
5.
Glue together the Top pieces using the short side tabs.
6.
Using the tab along the bottom of the Top pieces, glue to the top of the Flower Side Panel pieces.
Caravan
Cut all of the pieces within the files listed in the following quantities.
Back x1 (there are 2 pieces in this file – cut one of each)
Base x 1
Door x 1
Front x 1 (there are 2 pieces in this file – cut one of each)
Roof x 1
Sides x 2
Stand x 1
Wheel x 2
Window x 1
1.
Cut out all the pieces as listed using your chosen cardstock.
2.
Using the two Front pieces of the Caravan, glue together using the tab.
3.
Using the two Back pieces of the Caravan, glue together using the tab.
4.
Glue the roof to the back of the caravan using the tabs. Start at the right hand side where the two back pieces join and
follow around the top edge of the back.
5.
Glue the two side pieces to the back and the roof using the tabs.
6.
Take the large part of the base and glue to the left side and back using the tabs. Take the narrow part of the base and attach
to the right side and back using the tabs. The final part of the base will make the wheel arch. Curve this around the edge of
the wheel arch shape using the tabs. Glue the base parts together using the tabs.
7.
To assemble the door, glue the solid rectangle piece behind the cut out hole in the door to create the window. Glue the
rectangle outline shape in front of the cut out hole to create the window frame. Glue the door to the back of the long
rectangle cut out shape, in the front piece of the caravan.
8.
For the window of the caravan, glue the solid rectangle to the back of the small rectangle cut out shape in the front piece of
the caravan. Glue the rectangle outline shape to the front of the small rectangle cut out shape to create the window frame.
9.
If you want to add any accessories inside the caravan, do so now!
10.
Glue the front of the caravan to the sides, base, and roof to complete the main structure.
11.
For the wheels, take the long piece and glue to the largest circle using the tabs. Top Tip: You can cut an extra large circle for
each wheel to glue to the back to strengthen the shape. Glue the smallest circle to the medium circle and glue in the centre
of the wheel to create a hub cap. Glue the wheels into the arches of the base.
12.
Assemble the stand using the tabs and attach to the base of the caravan.
This should be positioned on the opposite end of
the base to the wheels so the caravan
stands up.
Cross
Birdcage
1. Cut birdcage 1 and 2 from your chosen cardstock
2. Slot together using the grooves
Cupcake
Box
Solid Cupcake
Base x 1
Part 1 x 3
Part 2 x 3
1.
Cut the files listed above in the stated quantities.
2.
Using the small tab at the bottom of Part 1, glue to one of the sides of the base. Repeat this step on the next side of the base
using a Part 2 piece and continue to alternate the pieces.
3.
Glue the sides together using the long side tabs.
4.
To close the box, fold all of the Part one pieces into the centre. Then fold the Part Two pieces in overlapping the detail to
secure into place.
5.
Details from the Detail folder can be added to the tops of the Part 2 pieces if desired.
Icing and Sponge
This allows for a different card stock to be used for both the icing and the sponge elements of the box.
Base x 1
Icing Flower x 3
Icing x 3
Sponge x 6
1.
Cut the files listed above in the stated quantities.
2.
Using the tab at the base of the Icing Flower pieces, glue to three of the Sponge pieces.
3.
Using the tab at the base of the Icing pieces, glue to the remaining three Sponge pieces.
4.
Continue with the instructions for the Solid Cupcake from step 2.
Cutting
Guide
Birdcage Cross
1 x Birdcage Cross 1
1 x Birdcage Cross 2
Birdgcage Frame
8 x Birdcage 1
1 x Bird
Ornate Birdcage
1 x Birdcage Base
2 x Birdcage Front
2 x Birdcage Side Panel
2 x Birdcage Roof
1 x Birdcage Stand 1
1 x Birdcage Stand 2
If using Mat layers on the stand
2 x Birdcage Stand Mat layer 1
2 x Birdcage Stand Mat Layer 2
Cake Slice Box
1 x Base
1 x Lid of your choosing
Large Cake Stand
1 x Top Tier
1 x Bottom Tier
1 x Stand Part 1
1 x Stand Part 2
Mini Cake Stands
1 x All pieces in file
Caravan
Back x1 (there are 2 pieces in this file – cut one of each)
Base x 1
Door x 1
Front x 1 (there are 2 pieces in this file – cut one of each)
Roof x 1
Sides x 2
Stand x 1
Wheel x 2
Window x 1
Cupcake Box
Solid Cupcake
Base x 1
Part 1 x 3
Part 2 x 3
Icing and Sponge
This allows for a different card stock to be used for both the icing and the sponge elements of the box.
Base x 1
Icing Flower x 3
Icing x 3
Sponge x 6
Buttercup
2 x Buttercup
1 x Buttercup Centre
As many leaves as required
Daisy
2 x Daisy
1 x Daisy Centre
Leaves as required
Forget Me Not
1 x Forget Me Not
1 x Forget Me Not Foliage
Repeat and add leaves as required.
Dahlia
Do three rows of Petal 1 starting from the outside and working in, then fill the remaining space with Petal 2.
Add foliage and leaves as required.
Gerbera
2 x Petals Inner
2 x Petals Outer
2 – 4 x Centre depending on the effect required. Can use varying sizes if desired.
Dahlia
3 x Petal 1
3 x Petal 2
3 x Centre
3 x Centre Inner
Leaves as required
Giant Rose
1 x Petals 1
1 x Petals 2
1 x Petals 3
1 x Petals 4
1 x Petals 5
1 x Petals 6
1 x Petals Centre
1 x Rose Foliage
Giant Sunflower
1 x Sunflower Petals
3 x Centre 1
2 x Centre 2
2 x Centre 3
Ivy
1 x Stem
5 x Ivy
Rose
1 x Rose Foliage
1 x Rose (file has several shapes in, cut all of them once)
Leaves as required.
Rose Bud
1 x Rose Bud
1 x Rose Bud Centre
1 x Rose Bud Foliage
Leaves as required.
All in One Box
Flower Panel Version
4 x Flower Side Panel
4 x Top
All in One Box
2 x Side Panel
Bag Box
2 x Bag Box
OR
2 x Bag Box Heart Panel
Basic Box
1 x Basic Box
Birdcage Box
4 x Birdcage Box
Chocolate Box
One Base and Part 1 and Part 2 of desired design.
Square Cone Box
1 x Square Cone Box
Cone Pillow Box
1 x Cone Pillow Box
Exploding Pentagon Box
1 x Exploding Pentagon Box Base
1 x Exploding Pentagon Box Lid
Exploding Square Box
1 x Exploding Square Box Base
1 x Exploding Square Box Lid
Gift Bag
2 x Front and Back
1 x Gift Bag Base
2 x Gift Bag Side
Hexagon Box
1 x Hexagon box
Interlocking Box
1 x Interlocking Box
Love Heart Box
1 x Love Heart Box
Recipe Box
1 x Recipe Box Portrait Back
1 x Recipe Box Portrait Base
1 x Recipe Box Portrait Front
2 x Recipe Box Portrait Lid Side
1 x Recipe Box Portrait Lid
2 x Recipe Box Portrait Side Panel
Quick Box
1 x Quick Box Base
1 x Quick Box Lid
2 x Quick Box Side Panel
Matchbox
1 x Matchbox Drawer
1 x Matchbox Wrap
Pillow Box
2 x Pillow Box
Popcorn box
1 x Popcorn Box
Star Box
1 x Star Box Base
1 x Star Box Lid
Triangle Box
1 x Triangle Box
Lantern
4 x desired design panel
1 x Lantern Handle
Milk Jug
Part 1 x 1
Part 2 x 1
Part 3 x 1
Part 4, 6, 8 and 10 x 4
Part 5, 7, and 9 x 3
Part 11 x 1
Part 12 x 1
Saucer
Base x 2
Top x 2
Sugar Bowl
Bowl
Base Part 1 x 1
Base Part 2 x 1
Part 1 x 1
EITHER Version 1 -Part 2 x 6
OR
Version 2 - Part 2 Flower (Swirl) x 6, and Insert Panel x 6
Lid
Handle Base x 1
Handle Top x 1
Handle x 6
Part 2 x 6
EITHER Version 1 -Part 1 x 6
OR
Version 2 - Part 1 Flower x 6, and Insert Panel x 6
Teacup
Cup
Base Part 1 x 1
Base Part 2 x 1
Part 1 x 1
EITHER Version 1 - Part 2 x 6
OR
Version 2 - Part 2 Swirl x 6, and Insert Panel x 6
Handle
Tea Cup Handle Join x 1
Tea Cup Handle Side 1 x 1
Tea Cup Handle Side 2 x 1
Teapot
Handle
Handle x 1
Lid
Handle Base x 1
Handle Top x 1
Handle x 6
EITHER Version 1 -Part 1 x 6 and Part 2 x 6
OR
Version 2 - Part 1 x 6, Part 2 Swirl x 6, and Insert Panel x 6
Trim x 1
Pot
Base x 1
EITHER Version 1 -Part 1 x 6 and Part 2 x 6
OR
Version 2 - Part 1 x 6, Part 2 Swirl x 6, and Insert Panel x 6
Stand Part 1 x 1
Stand Part 2 x 1
Spout
1 x Part 1
1 x Part 2
1 x Part 3
1 x Part 4
1 x Part 5
1 x Part 6
Frame
Birdcage
1.
Cut 8 of the birdcage frame from your chosen cardstock.
2.
Mountain fold the dashed lines at the base and valley fold the tab at the top. Carefully attach the base tab to the bottom
of the frame.
3.
Stick the valley folded tab to the top of the first piece and repeat until the last piece.
4.
Using the base tab of the very first piece stick this to the bottom of the last piece and the stick the tab of the last piece.
Then top of the first.
Milk Jug
Base
Base Part 1 x 1
Base Part 2 x 1
1.
Cut the files listed above in the stated quantities.
2.
Glue Base Part 1 to Base Part two.
3.
Using the tabs, join the sides together to make up the base shape.
Bowl
Part 1 x 1
EITHER Version 1 -Part 2 x 6
OR
Version 2 - Part 2 Swirl x 6, and Insert Panel x 6
1.
Cut the above pieces in the stated quantities.
2.
If making version 2, mat the Insert Panel’s behind the Part 2 Swirl pieces.
3.
Glue the bottom tabs of the Part 2 pieces (or Part 2 Swirl pieces if making this version) to the middle shape of Part 1.
4.
Using the tabs on the Part 2 pieces, glue to the strips of Part 1. This will create the bowl shape.
5.
Glue the base made in the previous steps to the bottom of the bowl.
Handle
1.
Cut one of each shape within the file.
2.
Glue the long strip to one of the sides using the tabs.
3.
Glue the remaining side to the tabs on the other side of the long strip to form the handle.
4.
Glue to the bowl using the tabs.
Milk Jug
Top and Spout
Part 1 x 1
Part 2 x 1
Part 3 x 1
Part 4, 6, 8 and 10 x 4
Part 5, 7, and 9 x 3
Part 11 x 1
Part 12 x 1
1.
Cut the above pieces in the stated quantities.
2.
Glue Part 2 to the right side tab of Part 1.
3.
Glue Part 3 to the right side of Part 2.
4.
Glue Part 11 to the left side of Part 1.
5.
Glue Part 12 to the left side of Part 11.
6.
Alternate the remaining parts in numerical order to complete the top.
7.
Glue to the bowl using the tabs.
Mini
Stands
1. Cut all parts of the file.
2. Slot together the two base parts to make the stand.
3. Slot the round top part onto the stand.
4. The Flower or Heart detail can be suspended in the cut out using thread if desired.
Ornate
Birdcage
Birdcage
1.
Cut the birdcage base once, the cut the birdcage front and birdcage side twice from chosen cardstock on the cutting
machine.
2.
Using a birdcage front fold along the dashed line tabs and glue the bottom to one edge of the birdcage base. Repeat
with the remaining birdcage front and glue to the opposite edge of the base.
3.
Take onc of the side piece and fold along the dashed line tabs and glue the bottom to the side of the base. Repeat with the
remaining side piece and glue to the last side of the base.
4.
Stick the side pieces tabs carefully to the front pieces, being careful to ensure a smooth edge.
5.
Cut the birdcage roof twice from your chosen cardstock. Fold along the dashed line and glue the scalloped tab to the othe
to create the roof.
6.
Gently stick the top tabs of the front and back panels of the birdhouse to the edge of the roof. To create a decorative
birdcage.
Stand
1.
2.
Cut the birdcage stand 1 and birdcage stand 2 once from mountboard. Cut birdcage stand mat layer 1 and birdcage
mat layer 2 twice from chosen cardstock. Mat the birdcage mat layer 1 to both sides of the birdcage stand1 to give the stand
stability. Repeat with the remaining cuts.
Slot the two stand pieces together. Fold along the dashed line tabs and carefully stick to the base of the birdhouse.
Saucer
Base x 2
Top x 2
1.
Cut the files in the quantities stated above.
2.
Mountain fold the scalloped edges of the Top shape along the score lines.
3.
Glue the two Top pieces together at the centre of the shape.
4.
Use the side tabs to glue the saucer together.
5.
Glue the two Base pieces together at the centre of the shape.
6.
Use the side tabs to glue the base of the saucer together.
7.
Glue the completed Top part of the saucer to the completed Base part of the saucer.
Sugar Bowl
Bowl
Base Part 1 x 1
Base Part 2 x 1
Part 1 x 1
EITHER Version 1 -Part 2 x 6
OR
Version 2 - Part 2 Flower (Swirl) x 6, and Insert Panel x 6
1.
Cut the files listed above in the stated quantities.
2.
If making Version 2, mat the Insert Panels behind the decorative Part 2.
3.
Using the tab at the bottom of Part 1, glue to one side of the base. Continue around the base alternating Part 1 and Part 2.
This will make up the bowl shape.
Lid
Handle Base x 1
Handle Top x 1
Handle x 6
Part 2 x 6
EITHER Version 1 -Part 1 x 6
OR
Version 2 - Part 1 Flower x 6, and Insert Panel x 6
1.
Cut the files listed above in the stated quantities.
2.
If making Version 2, mat the Insert Panels behind the decorative Part 2.
3.
Join one Part 1 to one Part 2 and continue to alternate the pieces. This will make the domed shape of the lid.
4.
Glue together the Handle parts using the side panels.
5.
Glue the Handle Top to the top of the Handle.
6.
Glue the Handle Base to the top of the lid, leaving the hole clear.
7.
Tuck the tabs at the base of the handle into the hole and glue into place inside the lid.
Teacup
Cup
Base Part 1 x 1
Base Part 2 x 1
Part 1 x 1
EITHER Version 1 - Part 2 x 6
OR
Version 2 - Part 2 Swirl x 6, and Insert Panel x 6
1.
Cut the files listed above in the stated quantities.
2.
If making Version 2, mat the Insert Panels to the back of the Part 2 Swirl pieces.
3.
Glue the bottom tabs of the Part 2 pieces (or Part 2 Swirl pieces if making this version) to the middle shape of Part 1.
4.
Using the tabs on the Part 2 pieces, glue to the strips of Part 1. This will create the cup shape.
5.
Glue Base Part 1 to Base Part 2 and glue the side tabs to the neighbouring parts to make up the standing base.
6.
Glue the base to the bottom of the cup.
Handle
Tea Cup Handle Join x 1
Tea Cup Handle Side 1 x 1
Tea Cup Handle Side 2 x 1
1.
Cut the files listed above in the stated quantities.
2.
Using the tabs, glue Tea Cup Handle Join to Tea Cup Handle Side 1.
3.
Glue Tea Cup Handle Side 2 to the remaining tabs on the join.
4.
Use the tabs to glue the handle to the cup.
Teapot
Handle
Handle x 1
1.
Cut the files listed above in the stated quantities.
2.
strip.
Glue the long strip around the outside edge of one of the sides using the tabs. Glue the remaining side to the tabs on the
Lid
Handle Base x 1
Handle Top x 1
Handle x 6
EITHER Version 1 -Part 1 x 6 and Part 2 x 6
OR
Version 2 - Part 1 x 6, Part 2 Swirl x 6, and Insert Panel x 6
Trim x 1
1.
Cut the files listed above in the stated quantities.
1.
If doing Version 2, mat the Insert pieces behind the Part 2 Swirl Pieces.
2.
Glue a Part 1 to a Part 2 (or Part 2 Swirl piece if doing version 2) and continue to alternate parts. Join the ends together using
the tab. This will create the domed lid shape.
3.
To make the handle, glue the Handle pieces together using the side tabs. Glue the Handle Top piece to the top tabs of the
assembled Handle parts.
4.
Glue the Handle Base piece to the top of the assembled Parts 1 and 2, leaving the hole created by the parts clear.
5.
Tuck the tabs on the bottom of the handle into the hole and glue to the inside of the lid shape created by Parts 1 and 2.
6.
Glue the Trim around the base of the lid.
Teapot
Pot
Base x 1
EITHER Version 1 -Part 1 x 6 and Part 2 x 6
OR
Version 2 - Part 1 x 6, Part 2 Swirl x 6, and Insert Panel x 6
Stand Part 1 x 1
Stand Part 2 x 1
1.
Cut the files listed above in the stated quantities.
1.
If doing Version 2, mat the Insert pieces behind the Part 2 Swirl Pieces.
2.
Glue the tab at the end of a Part 1 to an edge of the Base. On the edge beside this glue the end tab of a Part 2 (or a Part 2
Swirl if making version 2). Continue to alternate pieces around the base.
3.
Using the tabs on the Part 2’s, glue to the Part 1’s until all are joined. This will form the Pot shape of the teapot.
4.
Glue Stand Part 1 on top of Stand Part 2 and join the edges together using the tabs. Glue the completed stand to the base
of the pot.
Spout
1.
Cut one of each part in this section.
2.
Using the tabs on Part 1, glue to Part 2. Then using the tabs on Part 2, glue to Part 3. Continue to attach each part to the
next in numerical order and join to form the spout.
Assembly
1.
Glue the completed handle to the pot.
2.
Glue the completed spout to the opposite side of the pot.
3.
The lid can either be placed on the pot and therefore kept as a removable part or it can be glued in place.