PRODUCT RANGE GUIDE
Pg 1/3
03/11
HiBuild 1000
Description
High Build Waterproofing Membrane
Special Features & Physical Properties
• Engineered to give uniform film coverage on textured and coarse surfaces up to 1000 microns per coat.
• Extremely high Solids Content with a minimum of shrinkage – bridges cracks up to depth of dry film build.
• Elastomeric properties ideally suited to a range of remedial applications on porous or cracking surfaces.
• Excellent adhesion and elastomeric properties – ideal for buildings subject to flexing and movement.
• Highly thixotropic properties allow the creation of textures up to 5mm in height.
• High application rates means only one coat of HiBuild 1000 may be required on many applications.
• Mould and fungus growth inhibitors to ensure paint condition and appearance is maintained.
• Colour Range: standard bases can be tinted to a large range of White, Pastel and Dark and very Deep
colours. No colour over coating required.
• Environmentally friendly formulation: low odour and lead free.
Typical Uses
• Building subject to flexing and/or movement
• Water proofing structures subject to cracking and/or porosity
• Creating textured finishes
• Creating a more even appearance on irregular substrates
Gloss Level
Low Sheen ≈ 15%
Volatile Organic Compounds
The American Society for Testing and Materials – ASTM D3960
Nil
Recommended Substrates
• Concrete walls
• Solid Plaster finishes
• Cementitious cladding
• Stucco
• Brick & block work
• Tilt Slab
Product specifications change from time to time and may differ from those published.
PRODUCT RANGE GUIDE
Pg 2/3
03/11
Dry Times
Depending on such factors as film thickness, ambient air temperatures, humidity levels and air circulation the
general dry times are:
Touch Dry
30 – 60 minutes
Re-Coat Time
2 – 6 hours
Application is not recommended if the surface and/or air temperature is less than 10˚C.
Application Methods
• Application by airless spray gun is recommended to attain specified wet film builds.
• Nap Rollers with 16mm piles or greater are recommended for creating fine textures.
• Goop Loop Roller are recommended for creating heavy textures
Surface Preparation
General Preparation
• All loose material such as peeling, flaking paint or poorly adhering substrate should be removed and surface
damage or imperfections made good.
• The surface must be clean and free of contaminants. Weathered surfaces should be water-blasted and any
contaminated surfaces etched and cleaned.
• Cracks should be filled with an elastomeric filler after the application of PaintPlus Masonry Sealer.
• Moss and mould infected areas should be treated and waterblasted.
• Prepare glossy areas by acid etching or grinding and thoroughly cleanse with a water blaster or a soft brush
and hose to remove release agent residues and loose particles.
Paint Requirements
New Cementitious surfaces
Prep Coat
Apply 1 coat of PaintPlus Masonry Sealer
1st Coat
Wet film build of 200 to 1000 microns
2nd Coat
Wet film build of 200 to 1000 microns
Requirements
Smooth surfaces 4 – 5 square meters per litre per coat
Coarse surfaces 3 – 4 square meters per litre per coat
Textured surfaces 1 – 2 square meters per litre per coat
Product specifications change from time to time and may differ from those published.
PRODUCT RANGE GUIDE
Pg 3/3
03/11
New Cementitious surfaces – Texturing
Prep Coat
Apply 1 coat of PaintPlus Masonry Sealer
1st Coat
Wet film build of 500 to 1000 microns
2nd Coat
Wet film build of 500 to 1000 microns
Requirements
1 – 2 square meters per litre per coat
Note: PaintPlus HiBuild 200 is recommended if a fine stipple finish is required
Prepainted surfaces in sound condition
1st Coat
Wet film build of 200 to 1000 microns
2nd Coat
Wet film build of 200 to 1000 microns
Requirements
Smooth surfaces 4 – 5 square meters per litre per coat
Coarse surfaces 3 – 4 square meters per litre per coat
Textured surfaces 1 – 2 square meters per litre per coat
Surfaces with superficial porosity and/or cracking
Prep Coat
filler.
Apply 1 coat of PaintPlus Masonry Sealer and fill any deep cavities or cracks with suitable
1st Coat
Wet film build of 200 to 1000 microns
2nd Coat
Wet film build of 200 to 1000 microns
Requirements
Smooth surfaces 4 – 5 square meters per litre per coat
Coarse surfaces 3 – 4 square meters per litre per coat
Textured surfaces 1 – 2 square meters per litre per coat
Thinning & Hot Weather Retardant
Not generally recommended, thinning will affect the features of this product. HiBuild 200 is recommended if a
lower viscosity product is required.
PaintPlus Hot Weather Retardant may be added during very hot weather at the rate of 50mls per litre but is
not recommended for higher film build applications.
Clean Up
All equipment may be cleaned in water.
Product specifications change from time to time and may differ from those published.