TC17-19 26 April 2017 (471KB PDF)

Commonwealth
of Australia
No. TC 17/19, Wednesday, 26 April 2017
Published by the Commonwealth of Australia
Gazette
TARIFF CONCESSIONS
CONTENTS
TCO Applications ................................................................................................... 2
TCOs Made ............................................................................................................. 8
Local Manufacturer Initiated - TCO Revocation Requests ................................. 12
Customs Initiated - Intention to Revoke Cancelled ............................................ 13
Intention to Revoke TCOs not used in over 2 years ........................................... 14
TCOs Revoked - Unused for over 2 years ........................................................... 17
Comptroller-General of Customs Initiated - TCOs Revoked .............................. 21
Comptroller-General of Customs Review of TCO Applications Notification ..... 22
Cheese Quota Transfers ...................................................................................... 23
The Commonwealth of Australia Tariff Concessions Gazette
(the Tariff Concessions Gazette) is free of charge on the DIBP
internet site at:
http://www.border.gov.au/Busi/domestic-manufacturers-and-importers
The Tariff Concessions Administration Section is located at
5 Constitution Ave Canberra City 2601
Contact details:
General Email Inquiries:……………………………[email protected]
General Inquiries: ............................................................ (02) 6229 3567
TAPIN help desk: ............................................................. (02) 6275 6534
Facsimile: ......................................................................... (02) 6223 8180
Cat. No.
ISSN 0813-8389
©Commonwealth of Australia, 2017
2
TCO Applications
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
TCO Applic ations
CUSTOMS ACT 1901 - NOTICE PURSUANT TO SECTION 269K(1) - APPLICATIONS MADE FOR TARIFF CONCESSION ORDERS
Applications have been lodged for Tariff Concession Orders for the goods described in the following TABLE.
Australian manufacturers who wish to contest the granting of a Tariff Concession Order for the goods described
are invited to lodge a submission in writing in an approved form. Submissions must be lodged within 50 days
of the date of publication of this Notice.
The operative date (Op.) and TC reference number follow the description of goods.
To assist local manufacturers, the use(s) to which the goods can be put follow the description of goods.
Objections to the making of TCO submission forms are available at
http://www.border.gov.au/Forms/Documents/b444.pdf
Contact: Email [email protected]
THE TABLE
Description of Goods including the
Customs Tariff Classification
3926.90.90
TEST TUBES, polystyrene, having BOTH of the following:
(a) width NOT greater than 13 mm;
(b) length NOT greater than 75 mm
Op. 29.03.17
Schedule 4 Item Number
General Duty Rate
50
- TC 1734307
Stated Use:
For storing laboratory samples for testing and analysis
Applicant:
5108.10.00
SYSMEX AUSTRALIA PTY LTD
YARN, BABY ALPACA, on cones, having ALL of the following:
(a) thread count NOT less than 2/16 Nm and NOT greater than
2/60 Nm;
(b) composition NOT less than 60% baby alpaca
Op. 29.03.17
5%
50
- TC 1734305
Stated Use:
Machine knitting of garments, accessories and homewares (throws,
blankets etc)
Applicant:
8309.90.00
AUSTRALIAN ALPACA WEAR
CLOSURES, CAN END, resealable, including ALL of the following:
(a) outer ring;
(b) aluminium foil membrane;
(c) plug;
(d) diameter NOT less than 103 mm
Op. 21.03.17
5%
50
- TC 1730996
Stated Use:
Resealable closure for metal cans
Applicant:
8421.29.90
VISY PACKAGING PTY LTD
FILTERS, CHEESE MAKING WHEY
Op. 30.03.17
5%
50
- TC 1734769
Stated Use:
For the recovery of whey particles by a filtering process during
the cheese making process
Applicant:
THE WARRNAMBOOL CHEESE AND BUTTER FACTORY COMPANY LTD
5%
3
TCO Applications
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Description of Goods including the
Customs Tariff Classification
8422.30.90
GAS CYLINDER FILLING PLANT, programmable logic controlled,
including ALL of the following:
(a) filling modules;
(b) mixing modules;
(c) pumps;
(d) valves;
(e) buffer skid;
(f) piping;
(g) filling racks;
(h) sensors;
(i) gauges;
(j) probes
Op. 24.03.17
Schedule 4 Item Number
General Duty Rate
50
- TC 1732971
Stated Use:
Filling gas cylinders for industrial, hospitality and medical
applications
Applicant:
8427.10.00
BOC LIMITED
DOWN LAYER, STEEL COIL PACKAGING LINE
Op. 28.03.17
5%
50
- TC 1733477
Stated Use:
Removes steel coils from an exit turnstile, rotates them 90
degrees and then moves them to a packaging line and places them
on the line
Applicant:
8428.90.00
BLUESCOPE STEEL (AIS) PTY LTD
BRIDGE INSPECTION PLATFORMS, TRUCK OR TRAILER MOUNTABLE
Op. 23.03.17
5%
50
- TC 1732516
Stated Use:
Inspect underneath bridges
Applicant:
8428.90.00
EWP HIRE PTY LTD
HYDRAULIC ARMS, ROCK AND CEMENT BREAKING MACHINE TOOL HOLDER
Op. 30.03.17
5%
50
- TC 1734582
Stated Use:
For holding machine tools for breaking rocks in mining
operations and breaking cement structures in building
demolitions and recycling plants
Applicant:
8433.60.00
SANDVIK MINING AND CONSTRUCTION AUSTRALIA PTY LTD
EGG GRADING LINE, having ALL of the following:
(a) individual egg handling;
(b) throughput NOT less than 45 000 eggs per hour;
(c) infeed rollers AND egg shell ultraviolet disinfection;
(d) clean-in-place infeed egg rollers
Op. 27.03.17
5%
50
- TC 1732972
Stated Use:
Egg grading
Applicant:
MOBA ASIA
5%
4
TCO Applications
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Description of Goods including the
Customs Tariff Classification
8479.82.00
WOOD CHIP SIZE SCREENING AND SORTING MACHINES, having ALL of
the following:
(a) screw conveyor;
(b) throughput capacity NOT less than 430 m3/hour;
(c) screens
Op. 27.03.17
Schedule 4 Item Number
General Duty Rate
50
- TC 1733470
Stated Use:
For screening and sorting fresh wood chips as part the particle
board and fibre board manufacturing process
Applicant:
8479.82.00
BORG MANUFACTURING PTY LTD
WOOD CHIP SIZE SCREENING AND SORTING MACHINES, having ALL of
the following:
(a) throughput capacity NOT less than 90 m3/h;
(b) screens;
(c) water pipes AND nozzles
Op. 27.03.17
5%
50
- TC 1733472
Stated Use:
For separating various sizes of wood chips as part of the
particle board and fibre board manufacturing process
Applicant:
8479.89.90
BORG MANUFACTURING PTY LTD
GRAVIMETRIC DOSING MACHINES, having BOTH of the following:
(a) gravimetric dosing bins;
(b) throughput capacity of NOT less than 55 t/h
Op. 27.03.17
5%
50
- TC 1733471
Stated Use:
To weigh and measure goods such as wood chip particles from
dosing bins
Applicant:
8479.89.90
BORG MANUFACTURING PTY LTD
AIR BLOWERS, WOOD CHIP SEPARATING, having ALL of the following:
(a) gravimetric throughput NOT less than 25 t/h;
(b) volumetric throughput NOT less than 200 m3/h;
(c) maximum wind speed NOT greater than 3 m/sec
Op. 27.03.17
5%
50
- TC 1733474
Stated Use:
For the removal of heavy particles and pollutants such as sand
and stones from wood chips used in the manufacture of particle
board and fibre boards
Applicant:
8480.79.00
BORG MANUFACTURING PTY LTD
INNER BLOW MOULD SHELLS, PLASTIC CONTAINER MAKING, whether OR
not assembled, with OR without blow mould bases
Op. 14.03.17
5%
50
- TC 1728637
Stated Use:
For manufacturing plastic containers
Applicant:
KHS PACIFIC PTY LTD
5%
5
TCO Applications
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Description of Goods including the
Customs Tariff Classification
8481.20.00
GEARBOX CONTROL MODULE, dual-clutch transmission, with OR
without ANY of the following:
(a) software;
(b) oil pan
Op. 28.03.17
Schedule 4 Item Number
General Duty Rate
50
- TC 1734297
Stated Use:
Control of automatic transmission gearboxes in motor vehicles
Applicant:
8481.80.90
VOLKSWAGEN GROUP AUSTRALIA PTY LTD
EXPLOSION ISOLATION VALVES, poppet type having a centering
spring mechanism, including ALL of the following:
(a) nominal sizes (DN) NOT less than 100 and NOT greater than
600;
(b) elastomer gaskets;
(c) o-ring seals
Op. 28.03.17
5%
50
- TC 1734302
Stated Use:
To isolate process equipment from the effects of pressure
waves resulting from an explosion caused by dust or gas
Applicant:
8507.10.10
CMC TECHNOLOGIES PTY LTD
ACCUMULATORS, lead-calcium, 12 V, filled AND charged, with OR
without charge state indicator, including BOTH of the following:
(a) amp hours NOT exceeding 120 AH;
(b) amps NOT exceeding 580 A
Op. 28.03.17
5%
50
- TC 1734294
Stated Use:
Supply of electric energy to motor vehicles
Applicant:
8512.90.90
VOLKSWAGEN GROUP AUSTRALIA PTY LTD
PARTS, WINDSCREEN WIPER, TRUCK AND/OR BUS, being ANY of the
following:
(a) wiper blade assemblies, comprising BOTH of the following:
(i) rubber wiper blade refills;
(ii) wiper blade frames,
(b) wiper arms;
(c) plastic AND/OR metal backed rubber wiper blade refills;
(d) wiper linkages;
(e) wiper frame
Op. 24.03.17
5%
50
- TC 1732965
Stated Use:
Windscreen wipers for truck and bus windscreens
Applicant:
8518.50.00
SCANIA AUSTRALIA PTY LTD
LOUDSPEAKERS, electronic, portable, having ALL of the following:
(a) microphone;
(b) vehicle attachment magnetic holders;
(c) remote controls;
(d) carrying cases;
(e) voltage NOT less than 12 V and NOT greater than 36 V
Op. 29.03.17
5%
50
- TC 1734308
Stated Use:
For installation on vehicles for advertising or to warn people
in emergency situations
Applicant:
DEMATEC ENERGY (SA) PTY LTD
5%
6
TCO Applications
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Description of Goods including the
Customs Tariff Classification
8537.20.90
SPEED DRIVES, PUMP, air cooled, with OR without fans,
with OR without circuit protectors, whether OR not
assembled, including ALL of the following:
(a) drive enclosure;
(b) input voltage NOT less than 2 100 V and NOT greater than
15 300 V;
(c) transformer;
(d) fused switch;
(e) vacuum contactors;
(f) filter
Op. 24.03.17
Schedule 4 Item Number
General Duty Rate
50
- TC 1732968
Stated Use:
Speed control in the operation of submersible and surface
electrically driven pumps
Applicant:
8544.30.00
SCHLUMBERGER AUSTRALIA PTY LTD
MOTOR VEHICLE WIRING KITS, 13-pin, consisting of ALL of the
following:
(a) wiring harness;
(b) 3-pin micro-switch housing;
(c) cable ties
with OR without trailer connection unit
Op. 29.03.17
5%
50
- TC 1734298
Stated Use:
Transmission of signals and/or electrical power for connection
to trailers
Applicant:
8705.90.00
VOLKSWAGEN GROUP AUSTRALIA PTY LTD
SURFACING VEHICLES, BITUMEN AND AGGREGATE, cab chassis, diesel
engine, having a gross vehicle weight NOT less than 30 t,
including ALL the following:
(a) bitumen AND aggregate dispersion, programmable logic
controlled;
(b) joysticks AND touch screens;
(c) camera;
(d) bitumen tank;
(e) aggregate hopper;
(f) telescopic bitumen sprayer;
(g) telescopic aggregate spreader;
(h) loading crane;
(i) NOT less than 6 wheels
Op. 10.03.17
5%
50
- TC 1727535
Stated Use:
Synchronous application of bitumen and aggregate to a road
surface
Applicant:
8708.99.99
ROADWORX SURFACING PTY LTD
PARTS, TRUCKS HAVING A GROSS VEHICLE WEIGHT GREATER THAN 3.5
TONNES, being fifth wheel couplings
Op. 23.03.17
5%
50
- TC 1732016
Stated Use:
Connection device between truck and trailer
Applicant:
JOST AUSTRALIA PTY LTD
5%
7
TCO Applications
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Description of Goods including the
Customs Tariff Classification
8716.90.00
PARTS, TRAILER AXLE ASSEMBLY HAVING A GROSS VEHICLE WEIGHT NOT
LESS THAN 7.5 TONNE, being ANY of the following:
(a) axle beams;
(b) axle booster brackets;
(c) brake shoes OR brake pads;
(d) drums;
(e) hub caps;
(f) hub spiders;
(g) hubs;
(h) axle plates;
(i) rotors;
(j) seal carriers, with OR without O-rings;
(k) thrust hub rings, with OR without lip seals OR O-rings;
(l) brake pad kits, consisting of BOTH of the following:
(i) brake pads;
(ii) NOT less than 2 of ANY of the following:
(1) retention clips OR locks;
(2) washers;
(3) springs;
(4) plugs;
(5) wearing plates;
(6) bolts,
(m) brake pad retainer kits, consisting of ALL of the
following:
(i) pad holding bars;
(ii) clamping springs;
(iii) bolts;
(iv) washers;
(v) locks,
(n) brake AND/OR hub dust covers
Op. 17.03.17
Schedule 4 Item Number
General Duty Rate
50
- TC 1730090
Stated Use:
For the manufacture or repair of on-road trailer axle assemblies
Applicant:
BPW TRANSPEC PTY LTD
5%
8
TCOs Made
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
TCOs Made
CUSTOMS ACT 1901 - NOTICE PURSUANT TO SECTION 269R(1) - TARIFF CONCESSION ORDERS MADE
Tariff Concession Orders have been made for the goods described in the following TABLE.
The operative date (Op.) and TC reference No. follow the description of goods. Local manufacturers of
substitutable goods may request the revocation of TCOs at any time.
THE TABLE
Description of Goods including the
Customs Tariff Classification
3808.91.90
3808.93.00
3824.99.90
3924.10.00
4811.41.90
6307.90.99
7305.39.00
7326.90.90
7326.90.90
Schedule 4 Item Number
INSECTICIDES, having a basis of cyantraniliprole
Op. 24.01.17
Dec. date 20.04.17
- TC 1708856
HERBICIDES, having an active ingredient of s-metolachlor
Op. 16.01.17
Dec. date 12.04.17
- TC 1706434
GRANULES, SULPHUR ABSORPTION, having ALL of the following:
(a) basic copper carbonate content NOT less than 70% and NOT
greater than 75%;
(b) basic zinc carbonate content NOT less than 10% and NOT
greater than 15%;
(c) calcium aluminate content NOT greater than 10%;
(d) attapulgite clay content NOT greater than 10%
Op. 05.01.17
Dec. date 18.04.17
DISPENSER, polypropylene, including BOTH of the following:
(a) serrated cutting edge;
(b) polyethylene film in a roll, having ALL of the following:
(i) thickness NOT less than 9 microns and NOT greater
than 12 microns;
(ii) width NOT greater than 33 cm;
(iii) length NOT greater than 90 m
Op. 16.01.17
Dec. date 21.04.17
PAPER, LABEL, in rolls, multi-layered, including ALL of the
following:
(a) width NOT less than 1 400 mm and NOT greater than 1 600 mm;
(b) paper face stock having a base weight NOT less than 99 gsm
and NOT greater than 132 gsm;
(c) clear polyethylene terephthalate (PET) release liner
having a basis weight NOT less than 37 g/m2 and NOT
greater than 47 g/m2;
(d) rubber based adhesive
Op. 23.12.16
Dec. date 18.04.17
SILAGE MATS, woven polypropylene, having BOTH of the following:
(a) weight NOT less than 200 gsm;
(b) UV rating NOT less than 700 kLy
Op. 06.02.17
Dec. date 18.04.17
50
50
50
- TC 1702707
50
- TC 1706435
50
- TC 1681874
50
- TC 1718374
PIPES, stainless steel, welded, having a circular cross section
external diameter NOT less than 450 mm
Op. 31.01.17
Dec. date 18.04.17
- TC 1716751
DISCHARGE HOPPERS, GERMINATING VESSEL, MALTING PLANT
Op. 19.01.17
Dec. date 18.04.17
- TC 1707679
RAINWATER DRAINAGE OUTLETS, siphonic, with OR without antivortex plate, with OR without overflow device, having BOTH of
the following;
(a) flow rate NOT greater than 65 l/s;
(b) gutter OR bitumen water proofing adapter plates
Op. 24.01.17
Dec. date 21.04.17
50
50
50
- TC 1708860
9
TCOs Made
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Description of Goods including the
Customs Tariff Classification
8418.30.00
8418.50.00
8419.39.90
8421.39.90
8424.89.90
8426.12.00
8428.90.00
8428.90.00
FREEZERS, chest-type, including ALL of the following:
(a) lockable steel OR glass lids;
(b) freezing temperature NOT less than minus 30 degrees and
NOT greater than minus 10 degrees Celsius;
(c) digital temperature display;
(d) integrated lock AND keys;
(e) capacity NOT less than 170 L
Op. 21.12.16
Dec. date 12.04.17
CHILLERS, upright, including ALL of the following:
(a) temperature display;
(b) glass doors;
(c) internal fluorescent OR LED lighting;
(d) adjustable shelving;
(e) capacity NOT greater than 1 400 L;
(f) adjustable temperature control NOT less than 1 degrees
Celsius and NOT greater than 11 degrees Celsius
Op. 21.12.16
Dec. date 12.04.17
DRYERS, including BOTH of the following:
(a) infrared lamps;
(b) conveyor
Op. 23.01.17
Dec. date 18.04.17
ISOLATION CHAMBERS, LABORATORY, VIAL FILLING, having ALL of the
following:
(a) main chamber, having ALL of the following:
(i) air filters;
(ii) glove ports;
(iii) air pressure gauges;
(iv) air pressure AND gas detection sensors,
(b) auxiliary chamber, having ALL of the following:
(i) air filter;
(ii) air pressure gauges;
(iii) air pressure AND gas detection sensors,
(c) air cooler;
(d) air extractor;
(e) dehumidifier
Op. 30.01.17
Dec. date 18.04.17
DISPENSING MACHINES, LIQUID CHEMICAL, with ALL of the
following:
(a) dosing pumps;
(b) flow meters;
(c) flush line
Op. 18.01.17
Dec. date 18.04.17
STRADDLE CARRIERS, having ALL of the following:
(a) NOT less than 4x4 wheels;
(b) semi-automated OR fully automated landside operation;
(c) remote positioning operation;
(d) maximum lifting capacity NOT greater than 320 000 kg
Op. 21.12.16
Dec. date 12.04.17
SORTING SYSTEM, CARPET AND VINYL ROLL, programmable logic
controlled, consisting of ALL the following:
(a) lifting tables;
(b) declining tables;
(c) conveyor belts;
(d) roll elevators;
(e) elevated sorting unit
Op. 06.12.16
Dec. date 12.04.17
STEEL TUBE BUNDLING AND STRAPPING LINE, having ALL of the
following:
(a) driven roller conveyors;
(b) chain conveyors;
(c) tube collecting cradles;
(d) packaging units;
(e) strapping units
Op. 08.12.16
Dec. date 12.04.17
Schedule 4 Item Number
50
- TC 1681252
50
- TC 1681249
50
- TC 1708187
50
- TC 1716111
50
- TC 1707237
50
- TC 1680920
50
- TC 1676032
50
- TC 1676691
10 TCOs Made
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Description of Goods including the
Customs Tariff Classification
8428.90.00
8430.41.00
8431.39.00
8474.10.00
8479.89.90
8479.89.90
8479.89.90
8479.90.90
8481.30.00
8483.40.90
STACKING TABLES, TRANSFORMER CORE, handling capacity NOT less
than 20 tonnes and NOT greater than 200 tonnes, adjustable
Op. 06.01.17
Dec. date 18.04.17
Schedule 4 Item Number
50
- TC 1703408
DRILLING MACHINES, UNDERGROUND, RAISE BORING, mobile,
articulated, having NOT less than eight wheels
Op. 12.01.17
Dec. date 12.04.17
- TC 1705693
DRIVE FRAMES, TAILGATE, ARMOURED FACE CONVEYOR
Op. 20.01.17
Dec. date 20.04.17
- TC 1708079
SCREENING AND WASHING SYSTEM, IRON ORE PROCESSING PLANT,
including ALL of the following:
(a) feed hopper;
(b) screeners;
(c) washer;
(d) conveyors
Op. 17.01.17
Dec. date 18.04.17
SERIALISATION AND INSPECTION PACKAGING MACHINES, being ALL of
the following:
(a) carton tracking machine;
(b) case packing machine;
(c) linemaster platform
Op. 06.12.16
Dec. date 21.04.17
CUT-ORDER MACHINES, programmable logic controlled, including ALL
of the following:
(a) supply AND discharge tables;
(b) pneumatic tipping cradles;
(c) unroll cradles;
(d) optical measuring unit;
(e) cross cutting knives;
(f) cutting inspection conveyor tables;
(g) rolling up units;
(h) integrated operator station
Op. 06.12.16
Dec. date 21.04.17
BOTTLE CLOSURE ASSEMBLY MACHINE, programmable logic controlled,
including BOTH of the following:
(a) automated feeder;
(b) assembling speed NOT less than 40,000 units per hour
Op. 10.01.17
Dec. date 18.04.17
PARTS, COIL BOX, HOT STRIP MILL, being ANY of the following:
(a) mandrels;
(b) mandrel shafts;
(c) mandrel segments;
(d) mandrel pull rods
Op. 09.01.17
Dec. date 18.04.17
50
50
50
- TC 1706911
50
- TC 1676027
50
- TC 1676029
50
- TC 1704604
50
- TC 1703415
REED VALVE MODULES, COMPRESSOR VALVE ASSEMBLY, having BOTH of
the following:
(a) steel alloy reed plates;
(b) plastic housing
Op. 10.01.17
Dec. date 20.04.17
50
- TC 1704611
GEARSETS, TAILGATE DRIVE, ARMOURED FACE CONVEYOR
Op. 20.01.17
Dec. date 20.04.17
- TC 1708078
50
11 TCOs Made
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Description of Goods including the
Customs Tariff Classification
8504.40.90
8516.29.00
8544.20.00
8701.95.90
8705.90.00
POWER STATION, SOLAR POWER PLANT, 1.8 MVA, having ALL of the
following:
(a) steel container with supporting legs;
(b) inverters;
(c) transformers;
(d) switchgear;
(e) DC input connections;
(f) AC output connections;
(g) motor-driven DC load-break switch;
(h) retractable maintenance platform;
(i) DC power NOT greater than 2,020 kW;
(j) voltage NOT greater than 1,000 V;
(k) rated input voltage NOT greater than 722 V;
(l) nominal AC voltage 20 kV
Op. 05.12.16
Dec. date 18.04.17
HEATERS, indoor OR outdoor, ceiling OR wall-fixed, having BOTH
of the following:
(a) power NOT less than 2,000 W and NOT exceeding 6,000 W;
(b) operational voltage NOT exceeding 240 V
Op. 21.12.16
Dec. date 12.04.17
CABLES, DOWNHOLE LOGGING, OIL AND/OR GAS WELL, wound on
motorised spooler, including ALL of the following:
(a) motorised spooler, with OR without spooler arms, including
ALL of the following:
(i) metal frame;
(ii) air drain valve;
(iii) air filter;
(iv) pressure gauges;
(v) water separator;
(vi) slip ring collector,
(b) jacket;
(c) armour wire;
(d) voltage rating NOT less than 650 V and NOT greater than
750 V;
(e) breaking strength NOT less than 25 kN and NOT greater than
30 kN
Op. 15.11.16
Dec. date 12.04.17
VEHICLES, AIRCRAFT TOWING, having an engine power exceeding
130 kW
Op. 23.01.17
Dec. date 18.04.17
TRUCKS, incorporating ALL of the following:
(a) compression ignition engine;
(b) view cameras;
(c) spray bars;
(d) brushes;
(e) water blasting machine
Op. 23.01.17
Dec. date 18.04.17
Schedule 4 Item Number
50
- TC 1675637
50
- TC 1681246
50
- TC 1669902
50
- TC 1708172
50
- TC 1708451
12 Local Manufacturer Initiated - TCO Revocation Requests
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Local Man ufact ure r Initi ated - TCO Rev ocati on Re ques ts
NOTIFICATION OF AN AUSTRALIAN INDUSTRY REVOCATION REQUEST - SECTION 269SC(1A) CUSTOMS ACT
Applications have been lodged for revocation of the Tariff Concession Orders set out in the following TABLE.
The Lodgement Request Date shown in the table below is the intended revocation date for the Tariff Concession
Order which will take effect should the application for revocation be successful.
Importations not covered by in-transit provisions may be subject to post action as any decision to revoke an
order is backdated to the date of request for revocation.
THE TABLE
Description of Goods including the
Customs Tariff Classification
8402.19.00
8402.20.00
8402.90.00
8402.90.00
8403.90.00
Schedule 4 Item Number
Lodgement Request Date
VAPOUR GENERATORS, CONCRETE CURING, having ALL of the following:
(a) generator output NOT greater than 450 kW;
(b) water cooled combustion chamber;
(c) water cooled pre-mix burner;
(d) temperature sensors AND controllers;
(e) noise insulated enclosure
Op. 19.01.16
Dec. date 11.04.16
- TC 1602954
BOILERS, STEAM, SUPERHEATED, HIGH PRESSURE
Op. 29.09.06
Dec. date 15.12.06
- TC 0615151
PARTS, STEAM GENERATION WATER-TUBE BOILER, ALUMINA PLANT, being
ANY of the following:
(a) buckstays;
(b) downcomers;
(c) headers;
(d) tubes or pipes, cut to shape;
(e) inner casings;
(f) pipe assemblies, being ANY of the following:
(i) roofs;
(ii) floors;
(iii) noses;
(iv) panels
Op. 13.01.09
Dec. date 03.04.09
PARTS, STEAM GENERATOR, POWER GENERATION PLANT, being ANY of the
following:
(a) inlet transition duct unit;
(b) inlet plenum;
(c) exhaust hood unit;
(d) stack adapter;
(e) exhaust stack unit;
(f) once through steam generator AND ducting erection joint
assembly kits, consisting of BOTH of the following:
(i) sheet metal sealing strips AND fastenings;
(ii) insulation,
(g) piping, valves AND instrumentation consisting of ALL of
the following:
(i) high pressure AND low pressure vent stack;
(ii) high pressure steam outlet piping;
(iii) low pressure steam outlet piping;
(iv) pilot-operated relief valve piping;
(v) high pressure feedwater inlet piping;
(vi) low pressure feed water inlet piping
Op. 06.01.16
Dec. date 04.04.16
PARTS, INDUSTRIAL GLASSHOUSE WETBACK BOILER, being ANY of the
following:
(a) tanks;
(b) shell and crown rings;
(c) spray tubes;
(d) overflows;
(e) manholes
Op. 23.08.10
Dec. date 15.11.10
50
18.04.17
50
18.04.17
50
18.04.17
- TC 0900688
50
18.04.17
- TC 1600940
50
18.04.17
- TC 1038767
13 Local Manufacturer Initiated - TCO Revocation Requests and
Customs Initiated - Intention to Revoke Cancelled
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Description of Goods including the
Customs Tariff Classification
8404.10.00
8404.90.00
Schedule 4 Item Number
Lodgement Request Date
AUXILIARY PLANT, STEAM BOILER, being superheater attemperators
with supports
Op. 04.01.11
Dec. date 21.03.11
PARTS, STEAM GENERATION BOILER AUXILIARY PLANT, being ANY of the
following:
(a) plates;
(b) chock liners;
(c) supports;
(d) fluid accumulators;
(e) junction boxes (non-electrical);
(f) control devices
Op. 18.02.08
Dec. date 27.06.08
50
18.04.17
- TC 1100392
50
18.04.17
- TC 0802705
Customs Initia ted - In tenti on t o Revok e Ca ncelled
CUSTOMS ACT 1901
CANCELLATION OF THE INTENTION TO REVOKE
The Request for revocation of the Tariff Concession Order for goods described in the following TABLE has been
cancelled.
THE TABLE
Description of Goods including the
Customs Tariff Classification
9503.00.99
DRAWING SCREENS, which use aluminium powder or aluminium powder
and beads as the means of graphic representation
Op. 01.01.07
Dec. date 27.11.06
Schedule 4 Item Number
50
- TC 0614719
14 Intention to Revoke TCOs not used in over 2 years
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Intenti on t o Revo ke TCOs n ot us ed in ove r 2 y ear s
TARIFF CONCESSION ORDERS (TCOs) NOT USED IN THE PREVIOUS 2 YEARS
The Comptroller-General of Customs is satisfied that the TCOs listed in the table below are no longer required
because, in the 2 years preceding the day of this notice, they have not been quoted in an import declaration
to secure a concessional rate of duty.
From Thursday, 25 May 2017, it is intended to take action to revoke these Orders under subsection 269SD (1A)
of the Customs Act 1901. In accordance with subsection 269SG (2) of the Customs Act 1901, in transit
provisions shall apply. If revoked, the expected date of effect will be 24 May 2017.
Interested parties are invited to provide, by close of business, Wednesday 24 May 2017, written reasons why an
Order should NOT be revoked.
Please advise if any of the Orders listed below have been quoted on an import declaration.
If a request is made to retain an Order used for the granting of a Determination, please specify the
Determination and the linked Item number to enable mapping to the Order and its scope.
Contact: Email [email protected]
THE TABLE
______________________________________________________________________________________________________________
Tariff
Description
Concession Number
Classification
______________________________________________________________________________________________________________
3920.99.00
TAPE, SWELLING, acrylate polymers in rolls
Op. 22.12.05
3926.90.90
- TC 0605450
Dec. date 14.07.06
- TC 0607300
FABRIC, comprising BOTH non-woven polypropylene AND
polypropylene microhook film
Op. 16.02.06
8417.10.00
Dec. date 09.06.06
BELLOWS, FUME EXHAUST, PICKLE LINE TANK
Op. 24.04.06
5603.12.00
- TC 0605481
LINERS, CONCRETE, HIGH DENSITY POLYETHYLENE OR POLYPROPYLENE,
THERMOPLASTIC, having BOTH of the following:
(a) conical anchor studs on one side;
(b) thickness NOT less than 2.0 mm and NOT greater than 10 mm
Op. 17.03.06
4016.99.00
Dec. date 22.03.06
Dec. date 21.04.06
- TC 0603913
FURNACES, SLAG, comprising ALL of the following:
(a) sootblowers;
(b) heat exchangers;
(c) waste heat boilers;
(d) condensers;
(e) coal mills;
(f) recuperators;
(g) cooling towers;
(h) blowers;
(i) dewatering bins;
(j) ladles;
(k) crane;
(l) dust collectors;
(m) rotary kilns;
(n) refractories;
(o) scrubbers;
(p) coolers;
(q) thickeners;
(r) cyclones;
(s) grinding mills
Op. 08.02.06
Dec. date 28.04.06
- TC 0603545
15 Intention to Revoke TCOs not used in over 2 years
Tariff
Classification
8417.80.00
Description
- TC 0607776
Dec. date 28.04.06
- TC 0603729
Dec. date 07.07.06
- TC 0606991
Dec. date 21.04.06
- TC 0603549
Dec. date 07.07.06
- TC 0606865
ROBOTICS, LABORATORY, MICRO ORGANISM PICKERS, having BOTH of the
following:
(a) image analyser;
(b) single picking head containing NOT less than 96 picking pins
Op. 01.03.06
8479.89.90
Dec. date 28.07.06
FEEDERS AND WEIGHERS, bentonite
Op. 11.04.06
8479.50.90
- TC 0606245
LOADING AND/OR UNLOADING STATIONS, ANODISING LINE
Op. 08.02.06
8428.90.00
Dec. date 30.06.06
DUCTS, PAPER MAKING, YANKEE DRYER HOOD
Op. 13.04.06
8428.90.00
- TC 0607779
NIOBIUM SHELL AND TUBE HEAT EXCHANGERS, PICKLE LINE
Op. 13.02.06
8419.89.90
Dec. date 21.07.06
PARTS, PRIME OVENS, CONTINUOUS PAINT LINE, being ANY of the
following:
(a) insulated panels;
(b) ducts;
(c) frames;
(d) burner supports;
(e) insulation;
(f) inside roof flashes and/or floor flashes;
(g) exhausts
Op. 03.05.06
8419.50.90
- TC 0605458
PARTS, FINISH OVENS, CONTINUOUS PAINT LINE, being ANY of the
following:
(a) flashings;
(b) ducts;
(c) bases;
(d) air and/or distribution boxes;
(e) filler plates;
(f) lifting lugs;
(g) gaskets;
(h) rail guard supports;
(i) quench partitions
Op. 06.04.06
8417.90.00
Dec. date 02.06.06
OVENS, PRIME, CONTINUOUS PAINT LINE, having ALL of the following:
(a) four heating zones;
(b) metal throughput NOT less than 33 000 kg/hour;
(c) maximum solvent load NOT greater than 300 litres/hour;
(d) recirculation flow NOT less than 160 000 cubic metres/hour;
(e) natural gas fired
Op. 03.05.06
8417.90.00
Concession Number
OVENS, FINISH, CONTINUOUS PAINT LINE, having ALL of the
following:
(a) NOT less than three heating zones;
(b) metal throughput greater than 33 000 kg/hour;
(c) natural gas fired
Op. 21.03.06
8417.80.00
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Dec. date 19.05.06
- TC 0604625
TRAPS, MAGNETIC, PULP MAKING OR RECONSTITUTING
Op. 15.03.06
Dec. date 02.06.06
- TC 0605330
16 Intention to Revoke TCOs not used in over 2 years
Tariff
Classification
8479.89.90
Description
SEAL
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
- TC 0607766
Dec. date 02.06.06
- TC 0605340
Dec. date 14.07.06
- TC 0607299
Dec. date 21.07.06
- TC 0607588
Dec. date 30.06.06
- TC 0606251
SETS, OIL FILM BEARING, consisting of All of the following:
neck seal with band;
seal end plate;
seal inner ring;
deflector ring;
coolant seal;
screws;
round body ring;
bumper
Op. 10.03.06
8705.90.00
Dec. date 21.07.06
DRIVE SHAFTS, CHARGE ROLLER TABLE, WALKING BEAM FURNACE, having
BOTH of the following:
(a) length NOT less than 600 mm;
(b) diameter NOT less than 220 mm
Op. 06.04.06
8484.20.00
- TC 0606252
BODIES, VALVE, HOT BLAST
Op. 01.05.06
8483.60.90
Dec. date 30.06.06
VALVES, RECIRCULATION, PICKLE LINE TANK, being ANY of the
following:
(a) pressure gauge isolation ball valves and/or pressure
transmitter isolation ball valves;
(b) acid drain ball valves;
(c) shut-off valves
Op. 24.04.06
8481.90.90
- TC 0605754
DAMPERS, MOTORISED, PRIME AND/OR FINISH OVEN, CONTINUOUS PAINT
LINE
Op. 21.03.06
8481.80.90
Dec. date 23.06.06
CARTS, ROLL, SCISSOR TYPE, CONTINUOUS STEEL STRIP PAINT LINE
Op. 03.05.06
8481.80.90
- TC 0605621
PARTS, CONTINUOUS PAINT LINE, STEEL STRIP, being ANY of the
following:
(a) uncoilers with hold down roll;
(b) recoilers;
(c) accumulator and accumulator columns;
(d) outboard bearings
Op. 07.04.06
8479.89.90
Dec. date 16.06.06
SETTERS AND CAPPERS, PLUG, AUTOMOTIVE BATTERY, programmable
logic control
Op. 28.03.06
8479.89.90
Concession Number
CIRCULATORS, OIL, STEAM TURBINE, comprising ALL of the following:
(a) storage tank;
(b) centrifugal pumps;
(c) control valves;
(f) oil filters;
(e) oil cooler
Op. 23.03.06
8479.89.90
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Dec. date 26.05.06
- TC 0605044
CONVEYORS, MATERIAL, VEHICLE MOUNTED
Op. 13.04.06
Dec. date 30.06.06
- TC 0606993
17 TCOs Revoked - Unused for over 2 years
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
TCOs Rev oked - U nuse d fo r ove r 2 yea rs
CUSTOMS ACT 1901
NOTICE PURSUANT TO SECTION 269SE(2) - TARIFF CONCESSION ORDER REVOCATION AT THE INITIATIVE OF THE COMPTROLLERGENERAL OF CUSTOMS
The Tariff Concession Orders listed in THE TABLE below have not been used for at least 2 years and have been
revoked under Section 269SD(1A). In transit provisions apply.
The intention to revoke these orders was notified in Gazette TC 17/12 dated 1 March 2017.
Contact: Email [email protected].
THE TABLE
Description of Goods including the
Customs Tariff Classification
7007.19.00
PANELS, GLASS, toughened, patterned, having ALL of the following:
(a) thickness NOT less than 3.1 mm and NOT greater than 3.3 mm;
(b) light transmittance NOT less than 91%;
(c) energy transmittance NOT less than 91%;
(d) iron content (Fe203) NOT greater than 0.015%
Op. 25.11.11
Dec. date 13.02.12
Schedule 4 Item Number
Last Date of Effect
50
28.03.17
- TC 1139399
Revoked for 2 years non use. In transit provisions apply
8605.00.00
FUNICULAR ROPEWAY PASSENGER RAILWAY CARS, complying with
Australian Standard 4722-2009 (AS 4722-2009)
Op. 11.07.12
Dec. date 10.10.12
50
28.03.17
- TC 1224725
Revoked for 2 years non use. In transit provisions apply
8607.19.00
ASSEMBLIES, PASSENGER TRAIN, consisting of BOTH of the following:
(a) gearbox;
(b) axle
Op. 27.03.13
Dec. date 17.06.13
50
28.03.17
- TC 1310847
Revoked for 2 years non use. In transit provisions apply
8704.23.00
TRANSPORTERS, PLATFORM, HAVING A GROSS VEHICLE WEIGHT GREATER
THAN 180 t, self propelled, having ALL of the following:
(a) NOT less than six wheel bogies;
(b) independent steering per bogie;
(c) maximum load capacity greater than 20 000 kg per bogie;
(d) hydraulic lift
Op. 21.05.10
Dec. date 09.08.10
50
28.03.17
- TC 1022777
Revoked for 2 years non use. In transit provisions apply
8705.20.00
SERVICE AND/OR DRILLING RIGS, truck mounted, self propelled,
free standing, having ALL of the following:
(a) triple drive axles;
(b) tandem steering;
(c) hydraulic pump AND tank;
(d) double drum drawworks;
(e) two stage hydraulic outriggers;
(f) hydraulic jacks;
(g) telescopic mast with maximum extension NOT less than 31 m;
(h) diesel engine;
(i) transmission;
(j) work platforms;
(k) hydraulic raising rams
Op. 20.11.12
Dec. date 11.02.13
Revoked for 2 years non use. In transit provisions apply
50
28.03.17
- TC 1244515
18 TCOs Revoked - Unused for over 2 years
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Description of Goods including the
Customs Tariff Classification
8705.40.00
TRUCKS, CEMENT MIXER, having ALL of the following:
(a) triplex pumps;
(b) densitometers;
(c) gauges;
(d) displacement tanks;
(e) cement mixers
Op. 01.09.09
Dec. date 20.11.09
Schedule 4 Item Number
Last Date of Effect
50
28.03.17
- TC 0932317
Revoked for 2 years non use. In transit provisions apply
8705.90.00
VIBRATORS, SEISMIC, four wheel drive, articulated
Op. 25.07.06
Dec. date 13.10.06
- TC 0612430
50
28.03.17
Revoked for 2 years non use. In transit provisions apply
8705.90.00
MOBILE PROCESSING UNITS, EXPLOSIVE MANUFACTURING OR BLENDING,
being an integrated self propelled vehicle AND processing AND
delivery plant including ALL of the following:
(a) chemical storage compartments;
(b) mixer AND/OR blender;
(c) explosive delivery module
Op. 13.08.12
Dec. date 29.10.12
50
28.03.17
- TC 1229786
Revoked for 2 years non use. In transit provisions apply
8705.90.00
TRUCKS, CONE PENETROMETER TESTING, having ALL of the following:
(a) 4 x 4 OR 6 x 6 wheel drive;
(b) ballast;
(c) cabin;
(d) hydraulic levelling jacks;
(e) hydraulic penetrometer pusher
Op. 12.09.12
Dec. date 03.12.12
50
28.03.17
- TC 1234807
Revoked for 2 years non use. In transit provisions apply
8705.90.00
COMBINED SWEEPER AND STREET CLEANERS, ride in, including ALL of
the following:
(a) spray bar;
(b) 4 wheel steer;
(c) water tank capacity NOT greater than 1 500 L;
(d) central cylindrical brush width NOT greater than 1 300
mm;
(e) maximum sweeper width NOT greater than 3 500 mm;
(f) waste hopper capacity NOT greater than 5 000 L;
(g) maximum operating speed NOT greater than 20 km/h;
(h) maximum non-operating speed NOT greater than 42 km/h
Op. 05.12.12
Dec. date 06.03.13
50
28.03.17
- TC 1246499
Revoked for 2 years non use. In transit provisions apply
8705.90.00
MOBILE CONVEYORS, ON ROAD CHASSIS, having ALL of the following:
(a) conveyors;
(b) telescopic boom, having a horizontal reach NOT less than
60 metres;
(c) NOT less than 10 driven wheels;
(d) diesel engines;
(e) chassis cabin
Op. 15.03.13
Dec. date 12.06.13
Revoked for 2 years non use. In transit provisions apply
50
28.03.17
- TC 1309471
19 TCOs Revoked - Unused for over 2 years
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Description of Goods including the
Customs Tariff Classification
8705.90.00
Schedule 4 Item Number
Last Date of Effect
VEHICLES, CLEANING SWEEPER, ride in, including ALL of the
following:
(a) water tank capacity NOT greater than 400 litres;
(b) waste hopper volume capacity NOT greater than 2.5 m3;
(c) central cylindrical brush width NOT greater than 1 300 mm;
(d) maximum sweeper width NOT greater than 3 500 mm;
(e) maximum operating speed NOT less than 30 km/h;
(f) debris conveyor;
(g) debris vacuum collector
Op. 24.04.13
Dec. date 05.08.13
50
28.03.17
- TC 1313771
Revoked for 2 years non use. In transit provisions apply
8705.90.00
SWEEPERS, VEHICLE, ROAD RAIL, having ALL of the following:
(a) length NOT greater than 6 900 mm with front boom;
(b) width NOT greater than 1 910 mm;
(c) height NOT greater than 2 800 mm;
(d) water tank capacity NOT less than 810 litres and NOT
greater than 1 810 litres;
(e) hopper capacity NOT greater than 4 m3;
(f) minimum curve radius 25 m;
(g) 2 sweeping levels
Op. 27.05.13
Dec. date 26.08.13
50
28.03.17
- TC 1317161
Revoked for 2 years non use. In transit provisions apply
8705.90.00
SWEEPERS, ride-in, mechanical suction, having ALL of the
following:
(a) maximum sweeper width NOT greater than 3 500 mm;
(b) main cylindrical brush width NOT greater than 1 300 mm;
(c) waste hopper capacity NOT greater than 5 000 litres;
(d) water tank capacity NOT greater than 500 litres
Op. 13.06.13
Dec. date 20.09.13
50
28.03.17
- TC 1319586
Revoked for 2 years non use. In transit provisions apply
8705.90.00
VEHICLES, CLEANING SWEEPER, ride in, including ALL of the
following:
(a) waste hopper capacity NOT greater than 5 m3;
(b) water tank capacity NOT greater than 600 litres;
(c) vacuum OR suction nozzle width NOT greater than 800 mm;
(d) gross weight NOT greater than 6 500 kg
Op. 03.10.13
Dec. date 16.12.13
50
28.03.17
- TC 1333311
Revoked for 2 years non use. In transit provisions apply
8705.90.00
MOTOR VEHICLES, being mobile electrical cable fault diagnostic
vans
Op. 28.10.13
Dec. date 13.01.14
50
28.03.17
- TC 1335988
Revoked for 2 years non use. In transit provisions apply
8709.19.00
TRACTORS, TOWING, ride on, internal combustion engine powered,
complying with Australian Standard AS 2359.7-1995 3.1.2.1,
having ALL of the following:
(a) maximum draw bar pull NOT less than 1 000 kg and NOT
greater than 1 900 kg;
(b) operator seated;
(c) maximum travel speed NOT less than 25 km/h
Op. 20.10.09
Dec. date 15.01.10
50
28.03.17
- TC 0939364
Revoked for 2 years non use. In transit provisions apply
8716.90.00
PARTS, WHEELED TROLLEY, being metal rod hatched shelves
incorporating shelving hooks
Op. 22.06.10
Dec. date 20.09.10
Revoked for 2 years non use. In transit provisions apply
50
28.03.17
- TC 1027814
20 TCOs Revoked - Unused for over 2 years
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Description of Goods including the
Customs Tariff Classification
8901.90.10
Schedule 4 Item Number
Last Date of Effect
BARGES, twin hull, inboard twin diesel powered, road
transportable, including ALL of the following:
(a) length NOT greater than 17.5 m;
(b) weight NOT exceeding 150 gross construction tons;
(c) moulded depth NOT less than 1.6 m;
(d) crane;
(e) winch
Op. 31.07.13
Dec. date 21.10.13
50
28.03.17
- TC 1325864
Revoked for 2 years non use. In transit provisions apply
9306.30.00
PROJECTILES, TRACER AMMUNITION
Op. 02.10.09
Dec. date 18.12.09
- TC 0937253
50
28.03.17
- TC 0813301
50
28.03.17
- TC 0825579
50
28.03.17
Revoked for 2 years non use. In transit provisions apply
9401.71.00
SEATS, BABY, VIBRATING
Op. 18.06.08
Dec. date 22.08.08
Revoked for 2 years non use. In transit provisions apply
9405.60.00
TAGS, MOBILE PHONE, NAME OR TITLE, flashing, solar powered
Op. 08.08.08
Dec. date 24.10.08
Revoked for 2 years non use. In transit provisions apply
9503.00.20
PARTS, DOLL, being ANY of the following:
(a) ceramic heads, including neck;
(b) ceramic heads, including neck, with head dress permanently
attached;
(c) ceramic legs, representing the foot to the knee;
(d) ceramic arms, representing the hand to the elbow;
(e) textile body, with partial limbs, not stuffed
Op. 01.01.07
Dec. date 27.11.06
50
28.03.17
- TC 0614612
Revoked for 2 years non use. In transit provisions apply
9503.00.70
SETS, FLOATABLE CRICKET, including ALL of the following:
(a) foam bat, incorporating a rigid plastic inner tube
and a rigid plastic handle;
(b) balls;
(c) floatable stumps, incorporating a plastic base
Op. 20.10.11
Dec. date 12.01.12
50
28.03.17
- TC 1135313
Revoked for 2 years non use. In transit provisions apply
9508.90.00
GENERATORS, WAVE, SWIMMING POOL
Op. 05.06.06
Dec. date 25.08.06
Revoked for 2 years non use. In transit provisions apply
- TC 0609665
50
28.03.17
21 Comptroller-General Of Customs Initiated - TCOs Revoked
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Compt rolle r-Ge ner al of Custo ms I nitiate d - TCOs R evok ed
CUSTOMS ACT 1901
TARIFF CONCESSION ORDER REVOCATION AT THE INITIATIVE OF THE COMPTROLLER-GENERAL OF CUSTOMS
The Tariff Concession Order listed in THE TABLE below has been revoked.
THE TABLE
Description of Goods including the
Customs Tariff Classification
8403.10.00
BOILERS, HOT WATER, BIOMASS SOLID FUEL, programmable logic
controlled, including ALL of the following:
(a) conveyors;
(b) furnace;
(c) fans;
(d) ash auger;
(e) emissions controller;
(f) fire tube boiler
Op. 28.09.16
Dec. date 30.01.17
TCO revoked following Comptroller-General's intention to revoke
notice in Tariff Concession Gazette TC 17/14 of 15 March 2017
Schedule 4 Item Number
Last Date of Effect
50
14.03.17
- TC 1655744
22 Comptroller-General of Customs Review of TCO Applications Notification
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Compt rolle r-Ge ner al of Custo ms Re view of TCO Applicati ons No tificatio n
CUSTOMS ACT 1901 - NOTIFICATION OF REQUEST FOR REVIEW OF APPLICATION DECISIONS
A request has been received for review by Immigration and Border Protection of the decision made on the
application for the Tariff Concession Order for goods described in the following TABLE.
THE TABLE
Description of Goods including the
Customs Tariff Classification
8431.39.00
PARTS, LONGWALL MONORAIL HAVING A TROLLEY LOAD CAPACITY
NOT LESS THAN 12.0 TONNES, being ANY of the following:
(a) chain assemblies, including ALL of the following:
(i) hanging bracket;
(ii) chain;
(iii) master link,
(b) articulated rail sections, length NOT greater than
2004 mm;
(c) curved rails;
(d) curved rail adaptors;
(e) breakpoint connection modules;
(f) pneumatic shunt drives AND/OR rail mules;
(g) push/pull module, with OR without frame;
(h) rigid cable trays;
(i) assemblies, hanging frame, including BOTH of the
following:
(i) frame;
(ii) suspension,
(j) spreader beams;
(k) transport sleds;
(l) assemblies, rail installation platform, including
BOTH of the following:
(i) platform;
(ii) rail end stop mechanism,
(m) rail transport pods;
(n) tool pods;
(o) push arms;
(p) trolleys, being ANY of the following:
(i) rigid AND/OR inbye;
(ii) flexible;
(iii) auxiliary
Op. 16.09.16
Schedule 4 Item Number
Date of Lodgement of Request
50
19.04.17
- TC 1653188
Initial
Decision
REFUSE
23 Cheese Quota Transfers
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
Cheese Quo ta Tra nsfe rs
IMMIGRATION AND BORDER PROTECTION
TARIFF QUOTAS - QUOTA TRANSACTIONS PROCESSED DURING THE PERIOD 11 APRIL 2017 TO 24 APRIL 2017.
GENERAL INFORMATION
This Gazette contains details of quota transactions processed during the period 11 April 2017 to 24 April 2017
inclusive.
Part 1 contains a Table specifying quota category details.
Part 2, Section A, lists quota holders who received quota allocations via transfer transactions.
Part 2, Section B, lists all adjustments to previous allocations which have been caused by transfer
transactions.
NB.- In Section B, transactions represent changes to individual tariff quotas and do not necessarily represent
the entire holdings in that category for the quota holder.
- The "AS WAS" and "AS IS" columns indicate the quota levels for that particular tariff quota only at
the time of that transaction.
- The amount of the transaction can be deduced by subtracting the "AS WAS" column from the "AS IS"
column.
Inquiries concerning any information published within this Gazette should be directed to Tariff Concession
Administration, Australian Border Force, 5 Constitution Avenue, Canberra City, ACT, 2601.
PART 1
NOTICE OF MAKING A DETERMINATION UNDER PART XVI OF THE CUSTOMS ACT 1901
In pursuance of Section 273B of the Customs Act 1901, notice is hereby given that a Determination specified in
Section A of Part 2 was made in relation to Item 55 in Part III of Schedule 4 to the Customs Tariff Act 1995
and subject to any conditions set out hereunder, that Determination applies to goods that are:
(1) specified in the Table hereunder;
(2) classified under a subheading of Schedule 3 to the Customs Tariff Act 1995, specified in Item 55 in Part
III of Schedule 4 to the Customs Tariff Act 1995;
(3) entered for home consumption not earlier than the start date, and not later than the finish date, by the
person specified in that Determination, as shown in Part 2; and
(4) in total, not in excess of such quantity as is specified in that Determination, as shown in Part 2.
In pursuance of Section 273B of the Customs Act 1901, notice is hereby given that a Determination specified in
Section B of Part 2 amended a previous Determination by deleting the figures in the column headed “QUANTITY AS
WAS" and inserting the figures in the column headed "QUANTITY AS IS".
THE TABLE
CATEGORY
CODE
UNIT
QUANTITY
QUOTA
ITEM
NUMBER
QUOTA
DESCRIPTION
311
Kilograms
61A
Cheese & Curd
24 Cheese Quota Transfers
Commonwealth of Australia Gazette
No TC 17/19, Wednesday, 26 Apr 2017
PART 2
SECTION A – QUOTA ALLOCATIONS
CAT
CODE
QUOTA HOLDERS LEGAL NAME
POST
CODE
QUANTITY (KG)
DETERMINATION
NUMBER
PART 2
SECTION B – AMENDED ALLOCATIONS
CAT
CODE
311
311
QUOTA HOLDERS LEGAL NAME
DELTA SALES PTY. LIMITED
KEBIA IMPORTEX PTY LIMITED
POST
CODE
3056
2204
QUANTITY (KG)
AS WAS
639,883.00
716,930.00
QUANTITY (KG)
AS IS
589,883.00
766,930.00
DETERMINATION
NUMBER
000767
000767