INSTALLATION
INSTRUCTIONS
PARTS LIST
Accessory
Application
BACK-UP SENSOR
2009 CR-V
Publications No.
AII 40413
Issue Date
AUG 2008
2
Corner sensor clips
Back-up Sensor Attachment Kit
P/N 08V67-SWA-100A
Back-up sensor control unit
Control unit bracket
Buzzer
Back-up sensor harness
Connector clip
2
Wire ties
Back-up sensor subharness
Wire tie with clip A
Right center sensor clip (Black)
Left center sensor clip (White)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
Wire tie with clip B
AII 40413 (0808)
08V67-SWA-1000-91
1 of 13
Wire tie with clip C
Back-up Sensor Kit
Right center sensor (blue)
LOCATING
PIN
EPT sealer
Left center sensor (blue)
LOCATING
PIN
Fuse label
2
2
Corner sensors (white)
LOCATING PIN
Self-tapping screws
Flange nut
Cable clip
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Ratchet
8 mm and 10 mm Socket
Accessory User’s Information Manual
Pushpin
Felt-tip pen
Drill
3 mm and 5 mm Drill bit
16 mm, 24 mm, and 26 mm Hole saw
Ruler
Eye protection (safety goggles, face shield, etc.)
10 mm Combination wrench
File
Diagonal cutters
Utility knife
2 of 13
AII 40413 (0808)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
Illustration of the Back-Up Sensors Installed on
the Vehicle
BACK-UP
SENSOR
SUBHARNESS
BACK-UP
SENSOR
HARNESS
3.
If equipped, remove the tonneau cover.
TONNEAU
COVER
BUZZER
Pull.
FUSE
(2 A)
LEFT
CORNER
SENSOR
CENTER
SENSORS
RIGHT
CORNER
SENSOR
CONTROL
UNIT
4.
Remove the right rear door sill trim (three clips).
RIGHT REAR
DOOR SILL TRIM
6311121B
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
3 CLIPS
NOTE: If you are also installing a trailer hitch, install the
back-up sensor first.
1.
Make sure you have the anti-theft codes for the radio
and navigation system if equipped, then write down
the radio presets.
2.
Disconnect the negative cable from the battery.
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
AII 40413 (0808)
FRONT
3 of 13
5.
Remove the trunk board (two hooks).
7.
Fold the rear seats forward, and remove the right
rear lid from the right cargo area side trim
(10 retaining tabs).
8.
Remove the vehicle bolt from the bracket of the right
cargo area side trim panel.
RIGHT CARGO AREA
SIDE TRIM PANEL
RIGHT REAR TRIM
PANEL BRACKET
HOOKS
TRUNK BOARD
6.
Remove the weatherstrip from around the rear trim
panel. Remove the rear trim panel (two bolts with tiedown hooks, two clips, and four clips).
10 RETAINING
TABS
2 CLIPS
4 CLIPS
FRONT
REAR TRIM
PANEL
9.
VEHICLE
BOLT
RIGHT REAR LID
6811060B
Remove the rear door and tailgate weatherstrip from
the right cargo area side and two clips from the trim
panel.
WEATHERSTRIP
8 CLIPS
WEATHERSTRIP
TIE-DOWN
HOOKS
2 BOLTS
6627010B
WEATHERSTRIP
CLIPS
FRONT
RIGHT CARGO AREA
SIDE TRIM PANEL
6905
10. Remove the right cargo area side trim panel
(10 clips).
4 of 13
AII 40413 (0808)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
11. Remove the seat belt from the right quarter pillar trim
(one cover and one vehicle bolt).
13. Remove the left rear splash guards (four self-tapping
screws).
RIGHT QUARTER
PILLAR TRIM
SEAT BOLT
COVER
FRONT
SPLASH GUARD
4 SELF-TAPPING
SCREWS
6620011Y
SEAT BELT
6222050B
12. Remove the right quarter pillar glass trim (seven
clips).
7 CLIPS
14. Remove the right rear splash guard (four selftapping screws).
15. With the help of an assistant, remove the rear
bumper (two bolt covers, two bolts, two flange bolts,
and three clips).
RIGHT QUARTER
PILLAR GLASS
TRIM
COVER
REAR
BUMPER
FLANGE
BOLTS
FRONT
6222060B
2 BUMPER
SCREWS
CLIPS
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
AII 40413 (0808)
REAR
BUMPER
FLANGE
BOLT
6222
5 of 13
16. Get the back-up sensor harness, and attach the 2 A
fuse label (2 A) to the fuse case.
19. Reinstall the vehicle 6-pin connector clip to the
vehicle panel.
FUSE
CASE
VEHICLE
PANEL
VEHICLE 6-PIN
CONNECTOR
CLIP
FUSE LABEL
(2 A)
FRONT
BACK-UP SENSOR
HARNESS
62160
17. Install the cargo area, remove the clip that secures
the vehicle 6-pin connector to the vehicle panel, and
disconnect the vehicle 6-pin connector.
VEHICLE 6-PIN
CONNECTOR
VEHICLE PANEL
BACK-UP SENSOR
HARNESS
6311021B
20. Secure the other 6-pin connector to the vehicle
harness with one wire tie.
CLIP
6-PIN
CONNECTOR
VEHICLE
6-PIN CONNECTOR
WIRE TIE
FRONT
VEHICLE
HARNESS
CUSHION
TAPE
6-PIN
CONNECTOR
FRONT
6-PIN
CONNECTOR
BACK-UP SENSOR
HARNESS
6311011B
18. Plug the back-up sensor 6-pin connector into the
vehicle 6-pin connector. Plug the other vehicle 6-pin
connector into the other back-up sensor harness 6pin connector.
6 of 13
VEHICLE PANEL
EDGE
BACK-UP SENSOR
HARNESS
6311031B
21. Using isopropyl alcohol on a shop towel, thoroughly
clean the area where the cushion tape will attach.
Attach the cushion tape to the edge of the vehicle
panel at the location shown.
AII 40413 (0808)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
22. Slide the control unit bracket onto the control unit.
Make sure that the three switches are in the down
position.
25. Insert the stud from the control unit bracket into the
hole in the vehicle panel, make sure that the bracket
tab is seated in the large hole. Secure the bracket to
the vehicle panel using the 6 mm flange nut.
CONTROL
UNIT
CONTROL
UNIT
CONTROL UNIT
BRACKET
STUD
SWITCHES
(Down positions.)
CONTROL UNIT
BRACKET
BRACKET
TAB
VEHICLE
PANEL
6905070B
FRONT
23. Plug the back-up sensor harness 14-pin connector
into the control unit.
CONTROL
UNIT
HOLE
LARGE
HOLE
6 mm
FLANGE
NUT
6311041B
26. Install the back-up sensor harness clip into the hole
in the vehicle panel.
VEHICLE
PANEL
CONTROL UNIT
BRACKET
HOLE
BACK-UP SENSOR
HARNESS CLIP
BACK-UP SENSOR
HARNESS 14-PIN
CONNECTOR
BACK-UP SENSOR
HARNESS
FRONT
6224060B
24. Attach the back-up sensor harness clip to the control
unit bracket.
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
AII 40413 (0808)
BACK-UP SENSOR
HARNESS CLIP
BACK-UP SENSOR
HARNESS
6224080B
7 of 13
27. Using a utility knife, trim off the right quarter pillar
glass trim in the area shown.
29. While wearing eye protection, drill a 4 mm hole at the
two marked points, and remove any burrs.
RIGHT QUARTER
PILLAR GLASS
TRIM
MARKS
UTILITY
KNIFE
10 mm
15 mm
Cut off.
RIB
6525501
28. Using a ruler and a felt-tip pen, measure and mark
the right quarter pillar glass trim in the area shown.
RIGHT QUARTER
PILLAR GLASS
TRIM
DRILL
(3 mm
5 mm
DRILL BIT)
RIGHT QUARTER
PILLAR GLASS TRIM
6525520B
30. While wearing eye protection, drill a 3 mm bit, drill a
hole at the marked point, then finish with a 16 mm
hole saw. Remove any burrs.
MARK
FELT-TIP
PEN
RIBS
18 mm
MARK
RIB
18 mm
6.5 mm
22 mm
13 mm
DRILL
(3 mm DRILL BIT)
6.5 mm
6525512B
8 of 13
AII 40413 (0808)
RIGHT QUARTER
PILLAR GLASS TRIM
DRILL
(16 mm HOLE SAW)
6525530B
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
31. Using isopropyl alcohol on a shop towel, clean the
right quarter pillar glass trim where the double-sided
tape will attach. Remove the adhesive backing from
the buzzer. Route the buzzer 2-pin connector
through the 16 mm hole, and install the buzzer in the
right quarter pillar glass trim with the two self-tapping
screws. Install with the on/off switch and the volume
control toward the front.
Without Vehicle Harness
VEHICLE
PANEL
WIRE TIE
WITH CLIP B
2-PIN
CONNECTOR
BUZZER
RIGHT QUARTER
DOUBLE-SIDED PILLAR GLASS TRIM SWITCH BUZZER
TAPE
5 mm
HOLE
VOLUME
CONTROL
5 mm
HOLE
FRONT
16 mm
HOLE
ADHESIVE
BACKING
BUZZER 2-PIN
CONNECTOR
VEHICLE
HARNESS
FRONT
BACK-UP SENSOR
HARNESS 2-PIN
CONNECTOR
VEHICLE
PANEL
6525543B
35. Secure the buzzer harness to the vehicle harness
with one wire tie.
BUZZER 2-PIN
CONNECTOR
2 SELF-TAPPING
SCREWS
BUZZER
6822011B
BUZZER
HARNESS
FRONT
32. Reinstall the right quarter pillar glass trim.
33. Plug the back-up sensor harness 2-pin connector
into the buzzer 2-pin connector.
With Vehicle Harness
BUZZER
2-PIN
CONNECTOR WIRE TIE
VEHICLE
HARNESS
VEHICLE
HARNESS
WIRE TIE
6525554B
BUZZER 2-PIN
CONNECTOR
FRONT
VEHICLE
PANEL
BACK-UP SENSOR
HARNESS 2-PIN
6905080B
CONNECTOR
34. Secure the 2-pin connector to the vehicle harness
with one wire tie (without vehicle harness: wire tie
with clip B).
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
AII 40413 (0808)
9 of 13
36. At the rear corner of the vehicle, remove the vehicle
grommet.
FRONT
BACK-UP SENSOR
HARNESS 6-PIN
CONNECTOR
BACK-UP SENSOR
SUBHARNESS
40. Route the back-up sensor subharness as shown,
and install the back-up sensor subharness clip into
the vehicle panel hole. Secure the back-up sensor
subharness:
With Rear Bumper Beam: Using isopropyl alcohol
on a shop towel, clean the rear bumper beam where
the cable clip will attach. Insert the back-up sensor
subharness into the holder of the cable clip. Remove
the adhesive backings from the cable clip, and attach the cable clip to the rear bumper beam as
shown.
GROMMET
cabin side
outside
FRONT
BACK-UP SENSOR
SUBHARNESS
VEHICLE GROMMET
(Discard.)
CABLE
CLIP
BACK-UP SENSOR
SUBHARNESS
HOLDER
6227010B
37. Route the back-up sensor subharness 6-pin
connector through the hole where the vehicle
grommet was removed, and seat the grommet of the
back-up sensor subharness grommet in the vehicle
hole.
38. Install the connector clip to the back-up sensor
subharness 6-pin connector.
BACK-UP
SENSOR
HARNESS
BACK-UP SENSOR
SUBHARNESS
6-PIN CONNECTOR
HOLE
VEHICLE
PANEL
BACK-UP SENSOR
SUBHARNESS CLIP
REAR BUMPER
BEAM
BACK-UP SENSOR
SUBHARNESS
6311052B
BACK-UP SENSOR
HARNESS 6-PIN
CONNECTOR
BACK-UP
SENSOR
SUBHARNESS
HOLE
FRONT
CONNECTOR
VEHICLE BACK-UP SENSOR CLIP
SUBHARNESS
PANEL
6-PIN CONNECTOR
6227020B
39. Plug the back-up sensor subharness 6-pin
connector into the back-up sensor harness 6-pin
connector, and install the connector clip. Secure the
clip in the vehicle panel hole in the area shown.
10 of 13
AII 40413 (0808)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
41. Route the back-up sensor subharness as shown.
Attach the back-up sensor subharness clips into the
holes in the vehicle panel.
43. While wearing eye protection, drill a 3 mm hole at the
eight pierced points you just made from the painted
side of the rear bumper.
HOLES
3 mm
DRILL BIT
VEHICLE
PANEL
DRILL
(24 mm
HOLE SAW)
MARK
UPPER
LOWER
MARK
24 mm
HOLE SAW
BACK-UP SENSOR
SUBHARNESS CLIPS
42. Using a pushpin, pierce the center and bottom of
each preset on the passenger’s side of the rear
bumper. Pierce the center and top of the other three
preset marks on the bumper. There are several
marks on the inside of the rear bumper; make certain
that you locate and pierce the proper preset marks.
3 LOCATING PIN
MARKS
2 LOWER
MARKS
26 mm
HOLE SAW
3 mm
DRILL BIT
631108
NOTE: Center holes are larger then the outer holes.
44. Enlarge the corner holes to 24 mm, and enlarge the
center holes to 26 mm using a hole saw. Remove
any burrs.
CORNER
SENSOR
Inside (White)
24 mm HOLE
Outside
REAR
BUMPER
CORNER
SENSOR
(White)
MARK
REAR BUMPER
PUSHPIN
LOCATING PIN
MARK
REAR BUMPER
45. Install the two corner sensors to the rear bumper
using the two corner sensor clips.
3 MARKS
PUSHPIN
MARK
2 MARKS
BACK-UP SENSOR
SUBHARNESS
REAR BUMPER
3 mm
DRILL BIT
CORNER
SENSOR
CLIP
LOCATING
PIN
REAR
BUMPER
6311072B
LOCATING Outside
PIN
Inside
REAR BUMPER
CORNER
SENSOR
CLIP
24 mm
CORNER HOLE
SENSOR
(White)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
AII 40413 (0808)
CORNER
SENSOR
(White)
6311091B
11 of 13
46. Install the right center sensor and left center sensor
on the rear bumper using right and left center sensor
clips.
47. Remove the rear bumper absorber from the rear
bumper beam.
REAR BUMPER
BEAM
RIGHT CENTER
SENSOR CLIP
(Black)
26 mm HOLE
Outside
Inside
REAR
BUMPER
RIGHT CENTER
SENSOR (Blue)
LOCATING
PIN
26 mm
HOLE
Outside
RIGHT
CENTER
SENSOR
(Blue)
REAR BUMPER
ABSORBER
Inside
6525560B
48. Using a utility knife, cut the rear bumper absorber
along the preset line at the location shown.
LEFT CENTER
SENSOR (Blue)
LEFT CENTER
SENSOR
(Blue)
LEFT CENTER
SENSOR CLIP
REAR
(White)
BUMPER
LOCATING
PIN
UTILITY KNIFE
6311100B
Cut off.
LINE
REAR BUMPER
ABSORBER
6525570B
12 of 13
AII 40413 (0808)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
49. With the help of an assistant, bring the rear bumper
near the vehicle, plug in the four back-up sensor
subharness 2-pin connectors into the sensors, and
reinstall the rear bumper.
REAR
BUMPER
BACK SIDE VIEW
52. Reinstall all removed parts.
53. Reconnect the negative cable to the battery.
54. Enter the anti-theft codes for the radio and
navigation systems, then enter the customer’s
radio presets.
BACK-UP SENSOR
SUBHARNESS
HOLDER
51. Check that all wire harnesses and cables are routed
properly and that all connectors are plugged in.
55. Reset the clock.
56. Test that the back-up sensors work as described in
the Accessory User’s Information Manual, which is
supplied in the kit.
4 BACK-UP SENSOR
SUBHARNESS
2-PIN CONNECTORS
CORNER
SENSOR
LEFT CENTER
SENSOR
RIGHT CENTER
SENSOR
REAR
BUMPER
CORNER
SENSOR
631111
50. Attach the holder of the back-up sensor subharness
to the rear bumper as shown.
© 2008 American Honda Motor Co., Inc. – All Rights Reserved
AII 40413 (0808)
13 of 13