zaag® root attachment system

%
*+,-./01+%23.134%
%
!""#$%&''(%"((")*+,-(%./.(,+%
%5$678%39:;'<%3=>"9:$%?$9$<"7@'9%
%
/2!AB*3.*C%*;@6%=':DE$97%:'97"@96%7;$%E'67%:D<<$97%@967<D:7@'96F%!G$"6$H%<$"=%"9=%<$7"@9F%
%
0,.)&12(1'-C%377":;E$97I%/97<"JB"=@:DG"<%K6DL%#@9#@>"GMF%19@>$<6"G%-@9#$I%B$6@G@$97%377":;E$97%('<%
$9='='97@:"GGN%7<$"7$=%<''76F%
%
%
%
ATTACHMENT COMPONENTS
% IMPORTANTNOTE: The inside diameters of the
ZAAG Standard and Mini females are different.
% Therefore, the males and other components are
NOT interchangeable.
%
ZAAG DENTURE CAP MALE
% (Gold Plated Stainless Steel Cap/ Nylon Male)
% ZAAG FEMALE
(Stainless Steel with Gold Colored
% Titanium Nitride Coating)
% ZAAG CAST-TO FEMALE
%
(Non-coated Stainless Steel
with LDPE Parallel Post)
%
% ZAAG REPLACEMENT MALE
(No Centering Sleeve)
% Nylon and plastic
% ZAAG IMPRESSION MALE
(Low Density Polyethylene)
%
ZAAG SUBSTITUTE MODEL FEMALE
% (Anodized Aluminum)
%
% ZAAG PARALLEL POST
(Low Density Polyethylene)%
%
!"#$%&%'(%)%
%
ATTACHMENT KITS
ZAAG attachment kits are available with your choice of Standard or Mini ZAAG females. The ZAAG Denture Cap
Tool Kit (Zest order #9201) contains the Denture Cap Male Coring Tool and Denture Cap Male Seating Tool
necessary for the quick change of a ZAAG male.
INDICATIONS
Overdentures or Partial Dentures. Appropriate for use with all appliances where remaining non-vital roots are to be
utilized as abutments. Designed for direct placement into the root without a cast coping. May also be cast-to with
precious or semiprecious crown and bridge alloys where a cast coping is desirable.
CONTRAINDICATIONS
Not appropriate where a totally rigid connection is required.
CAUTION: Federal (U.S.A.) law restricts this device to sale by or on the order of a licensed dentist.
FEATURES
•
Subgingival connection results in application of forces near the root center of support.
•
Wide band of wear area on both nylon male and metal female allows for longer attachment life.
•
Large diameter of nylon male shaft reduces bending and breakage.
•
Instant removal and Snap-Lock replaceability of males without removing denture acrylic.
•
Universal joint stress relief with vertical resiliency.
A. PLACEMENTOF THE FEMALE
Standard Size
1. Prepare and measure study casts to determine the space available in the root
for the standard size ZAAG Female. Width of root surface must equal or
exceed 4.0mm.
NOTE: It is best to use the standard size ZAAG Female whenever possible
because of it stronger, longer lasting male compared to the mini size.
2. Decoronate the root and perform endodontic therapy. The coronal surface of
the root should be prepared as low as possible.
3. Drill a pilot hole with a #700 carbide bur (RA type only) to a depth of 4mm.
Alignment of the drill should follow the path of insert ion of the denture. The
pilot hole need not follow root canal. (Fig. 1)
4. Enlarge the pilot hole with a #8 round RA carbide bur to a depth of 3mm.
(Fig. 2)%
!"#$%O%'(%)%
5. Complete the preparation for the prefabricated surgical stainless steel female
with the ZAAG Diamond Bur (Standard).The Diamond Bur should be used to a
depth where a full 360 degree recessed seat is created on the occlusal surface
of the root. (Fig. 3)This will assure firm seating of the female and a proper seal.
Keep the diamond bur rotating throughout th is entire procedure, including
insertion and removal of the instrument, to prevent breakage of the tip. Use
plenty of water as coolant during the sizing process.
6. Using the ZAAG Parallel Post as a handle ,try in the metal female to check for
proper fit. (Fig. 4) When placing multiple attachments, create the following pilot
holes as parallel as possible to the first preparation using the metal female with
the Parallel Post as a guide.
7. Cement the metal female component in place with composite resin cement or
a strong adhesion material of your choice.
8. After the cement has set, round off and polish the root surface from the metal
flange to the tissue. (Fig. 5)
IMPORTANT NOTE: It is imperative that the root surface immediately
surrounding a ZAAG attachment be finished down to the exact level or lower than
the top of the female. This will allow the ZAAG male with centering sleeve to seat
completely.
B. FABRICATION TECHNIQUE USING THE ZAAG ONE-STEP DRILLSTANDARD
1. Complete reduction of the non-vital teeth to the gingival level.
2. The ZAAG One-Step Drill (Standard) is self-starting and pilot holes are not
necessary.
3. At a slow speed (750 RPM), drill a hole with the Standard drill to a depth
where a full 360 degree recessed seat is created on the occlusal surface of the
dent al root. This will assure firm seating of the female and facilitate a proper
seal. Water should be used generously when cutting ZAAG One-Step Drill.
(Fig. 6)
�
C. PLACEMENT OF THE FEMALE
Mini Size
1. Prepare and measure study casts to determine the space available in the root
for the mini size ZAAG Female. Width of root surface must equal or exceed
3.5mm.
2. Decoronate the root and perform endodontic therapy. The coronal surface of
the root should be prepared as low as possible.
3. Drill a pilot hole with a #700 carbide bur (RA type only) to a depth of 2mm.
Alignment of the drill should follow t he path of insertion of the denture. The
pilot hole need not follow root canal. (Fig. 7)
4. Enlarge the pilot hole with a #8 round RA carbide bur to a depth of 2mm. (Fig.
8)
5. Complete the preparation for the prefabricated surgical stainless steel female
with the ZAAG Diamond Bur (Mini).The Diamond Bur should be used to a
depth where a full 360 degree recessed seat is created on the occlusal surface
of the root. (Fig. 9) This will assure firm seating of the female and a proper
seal. Keep the diamond bur rotating throughout this entire procedure, including
insertion and removal of the instrument. Use plenty of water as coolant during
the sizing process.
6. Using the ZAAG Parallel Post as a handle, try in the metal female to check for
proper fit. (Fig. 10) When placing multiple attachments, create the following
pilot holes as parallel as possible to the first preparation using the metal female
with the Parallel Post as a guide.
7. Cement the metal female component in place with composite resin cement or
a strong adhesion material of your choice.
8. After the cement has set, round off and polish the root surface from the metal
flange to the tissue. (Fig. 11)
IMPORTANT NOTE: It is imperative that the root surface immediately
surrounding a ZAAG attachment be finished down to the exact level or lower than
!"#$%P%'(%)%
the top of the female. This will allow the ZAAG male with centering sleeve to seat
completely.%
D. FABRICATION TECHNIOUE USING THE ZAAG ONE-STEP DRILL-MINI
1. Complete reduction of the non-vital teeth to the gingival level.
2. The ZAAG One-Step Drill (Mini) is self-starting and pilot holes are not
necessary.
3. At a slow speed (750 RPM), drill a hole with the Mini drill to a depth where a
full 360 degree recessed seat is created on the occlusal surface of the dental
root. This will assure firm seating of the female and facilitate a proper seal.
Water should be used generously when cutting with the ZAAG One-Step Drill.
(Fig. 12)
E. PLACEMENT OF THE MALE ANCHOR
Prepare and measure study casts to determine the space available for the
denture male component . The full size ZAAG Denture Cap Male extends 3.1mm
above the ZAAG Female. The ZAAG ST Cap Male extend just 2.0mm above the
female for use when lack of occlusal space is a problem.
F. MALE PLACEMENT BY THE LABORATORY
1. Cementation of the metal females and final root contouring is completed in the
dental office.
2. Place an Impression Male in the metal female in the oral cavity. Make sure the
impression male is fully engaged. The male should seat flush on the flange of
metal female component . (Fig. 13)
3. Take the impression exercising caution not to compress the soft tissue. The
Impression Males are designed with minimum retention to be drawn in the
impression.
NOTE: A vinyl polysiloxane impression material will easily pick up the Impression
Males. If an alginate material is preferred, retention of the Impression Males can
be reduced by using a blade to cut off a small section of its retentive band.
4. Place a Substitute Model Female onto each Impression Male in the
impression. Make sure each Substitute Female is fully seated. (Fig. 14)
5. Pour the master cast. Upon separation, the Substitute Female is a part of the
master cast replicating the position of the ZAAG Female in the oral cavity.
6. Place the Denture Cap Male, (consisting of the stainless steel cap, nylon male
and centering sleeve), into each Substitute Model Female. Males must be fully
seated. The centering sleeve eliminates movement of the male component
during processing. (Fig. 15)
7. Processing is completed.
8. Remove the centering sleeves from the males and relieve the acrylic over the
remaining root surface. There should be no contact between the root and the
acrylic saddle.
NOTE: Use a black polishing cap (Zest order #9001) to fit over and protect the
ZAAG nylon male from damage when polishing the denture or using a bur to
remove excess acrylic around the male.
G. MALE PLACEMENT BYTHE DENTIST
1. Cementation of the metal females and the final root contouring is completed.
2. Insert a ZAAG Denture Cap Male (metal housing side first) into the ZAAG
Male Placement Tool (Zest order #4961) (Fig. 16A).Use the tool to snap a
male into each cemented female. Check each male for proper retention, and to
make sure the centering sleeve seats firmly against the female, maintaining the
male in the center of the flare opening. (Fig. 16B)
NOTE: The Male Placement Tool is made for use only with the full size Denture Cap
Male. It does not fit the short cap of the ST(Short and Tough) Male.
3. Prepare a recess in the denture to accommodate the protruding ZAAG denture
component. There must be no contact between the denture and the metal cap. If
the denture rests on the male component, excess pressure on the root will result.%
!"#$%Q%'(%)%
4. Use the Chairside LightCure Acrylic Resin Syringe Kit (Zest order #9403) to
light cure bond the Denture Cap Male component into the denture (Fig. 17 &
18) or mix a permanent self-curing acrylic resin and place a small amount in
the recess of the denture and around the top of the metal cap.
5. Insert the denture into position in the oral cavity. Guide the patient into
occlusion, maintaining a proper relationship with the opposing arch. Maintain
the denture in a passive condition, without compression of the soft t issue,
while the acrylic sets. Excessive occlusal pressure during the setting time may
cause tissue recoil against the denture base and could contribute to dislodging
and wear of the ZAAG males.
6. Remove the centering sleeves from the Denture Cap Male components.
Relieve the acrylic over the remaining root surface. There should be no contact
between the root and the acrylic saddle. (Fig. 19)
NOTE: Use a black polishing cap (Zest order #9001) to fit over and protect the
ZAAG nylon male from damage when polishing the denture or using a bur to
remove excess acrylic around the male.
7. Instruct the patient in the path of insertion. Have the patient insert and remove
the appliance several times. The snap into retention should be accomplished
by finger pressure without the aid of the opposing teeth.
H. HOW TO CHANGE THE MALE
IMPORTANT NOTE: It is imperative that the nylon ZAAG male in the existing
metal denture cap be replaced with the exact same type. The retention diameters
of the ZAAG Standard and Mini males are different. The difference can be
measured at 2.1mm for the Standard ZAAG male, and 1.6mm for the Mini ZAAG
male. In addition, the replacement males are not the same for the full size
Denture Cap and the ST (Short and Tough) Denture Cap.
1. Use the ZAAG Denture Cap Tool Kit (Zest order #9201) containing a Male
Coring Tool, Male Seating Tool and Male Placement Tool to remove the nylon
male from the metal denture cap and replace it with a ZAAG Replacement
Male.
2. Using a lab hand piece, guide the ZAAG Denture Cap Male Coring Tool over
the nylon male and core out the center post of the male at medium RPM. (Fig.
20)
NOTE: If too much heat is generated, the metal cap may melt the surrounding
denture resin and dislodge. A small amount of cold water will help keep the metal
cool while coring out the nylon male.
3. The ZAAG Denture Cap Male Seating Tool utilizes a threaded plastic insert
with two (2) working ends. Use the end without a slot, with t he metal pin
provided, to eject the cored male post out of the ZAAG Denture Cap Male
Coring Tool. (Fig. 21)
4. Using a blade or explorer-like instrument, collapse the remaining plastic ring
into the open space created by removal of the center post and lift it out. (Fig.
22)
5. Insert a Replacement Male into the proper end of the threaded ZAAG Denture
Cap Male Seating Tool insert based upon the following sizes of the male:
a) The ZAAG Mini Replacement Male fits into the slotted end of the threaded
ZAAG Denture Cap Male Seating Tool insert . CAUTION: Make sure the
white reinforcing sleeve is in place to avoid breaking the slotted end of the
tool. (Fig. 23)
b) The ZAAG Standard Replacement Male fits into the end of the ZAAG
Denture Cap Male Seating Tool Insert without a slot. (Fig. 23)
6. Use the ZAAG Denture Cap Male Seating Tool to firmly push the new male
into the metal denture cap. The replacement male must seat securely into
place beneath the rim of the cap. (Fig. 24)
I. ZAAG CAST COPING
A special ZAAG Cast-To Female (Standard or Mini size without Titanium Nitride
coating) (Fig. 25) is used for cases where a gold cast coping is desired to cover
!"#$%R%'(%)%
and protect the root surface. The following procedure is
recommended for the Standard Cast-To Female.
2. The ZAAG Standard Cast-To Diamond Bur (Zest order #9517)
is used to make an adequate preparation for the wax-up of the
ZAAG Standard Cast-To Female. Follow the Diamond Bur
drilling steps on Page 3,Section C. Water should be used
generously when cutting with the Diamond Bur. (Fig. 26)
3. An impression is taken (Fig. 27), being sure to include other
attachments or enough anatomy to show the line of insertion of
the denture. The master cast and dies are prepared.
4. Using a surveyor, place the plastic Parallel Post with attached
Cast-To Female parallel with other ZAAG attachments. If
multiple attachments (4 or more) are planned, the prosthetic
path of insertion as directed by the flanges should not be
divergent in excess of 10 degrees for any of the ZAAG
attachments.
5. Wax the Cast-To Female directly into the die. The stainless
steel should be completely encased with a layer of wax up to ,
but not over, the junction of the Parallel Post . (Fig. 28)
NOTE: Use a hard wax so t he female will be held securely when
removing the Parallel Post.
6. Remove the Parallel Post, leaving the stainless steel
attachment cavity open for investment material to flow into. (Fig.
29)
7. Spruing. Run the sprue at a 45 degree angle to the Cast-To
Female so the molten gold will flow down along one side of the
female, around and up to the other side. The sprue should not be directed at
the female which could possibly dislodge it when casting.
8. It is recommended to use debubblizer to reduce surface tension during
investing procedures.
9. Investing. The most successful castings have been accomplished by using
Ceramigold Investment by Whip Mix Corp. or an equivalent High Heat
Investment. Use a casting ring at all times. (Do not use the ring less technique
of investing and casting for the Cast-To Female.)
10. Mix a liquid/powder ratio of Ceramigold using 12mL to 60 grams of powder
for each packet of mix needed. Hand mix for 15 seconds and vacuum mix for
90 seconds at (350-450 RPM). The investment material should be carefully
painted into each attachment cavity to avoid trapping bubbles and to prevent
gold from going inside the female. The remainder of the investment poured into
the ring will stabilize the female during burnout. Place the ring in a water bath
for one hour then, bench set for a half hour.
11 . Burnout. Place ring in cold furnace (sprue hole down) and raise temperature
to 1500 °F maximum. Use a rate of climb of 0°F to 1500 °F maximum over a
time period of one hour. Hold at 1500°F maximum until burnout is complete.
(Refer to investment manufacturer's instructions for suggested burnout
duration.)
12. Casting. Use only precious or semi-precious alloys for casting root copings.
Base metal alloys should not be used. Cast the coping using the
recommended temperatures of the alloy manufacturer. The stainless steel
female will withstand a temperature of up to 2,000 °F without any dimensional
change.
13. Divesting. After casting, allow all castings to bench cool for 20 minutes. Be
careful to push out casting and investment with proper tools. It is not
recommended to hammer or bang on rings which may distort castings. To
remove the investment material from the Cast -To Female without damage to
the stainless steel, use an acid-free investment and porcelain remover solution
(Kleen-It-American Dental Supply) in an ultrasonic unit for a period of 30-45
minutes. (Do not use a bur to remove the investment, sand blasting with
aluminum oxide, or an acid pickling solution, all of which can damage the
internal socket of the female attachment).Clean the coping containing the
ZAAG Cast-To attachments in an ultrasonic cleaner solution.
!"#$%S%'(%)%
14. Finishing and Polishing. When polishing with a rubber wheel, use caution not
to damage the Cast-To Female attachment. Polish the surface of the coping
to make a smooth mating surface for the male attachment. The Parallel Post
can be placed in the female to protect the attachment while polishing. (if
additional polishing of the female socket is needed, it is recommended to only
use glass beads at a low pressure 140 PSI) or a fiberglass or bristle polishing
brush).
15 .After polishing the coping, place a male attachment into each Cast-To
Female and check for proper fit. Clean again in ultrasonic solution and deliver
to the dental office to be cemented in place intra-orally on the prepared tooth
root.
16. The finished copings containing the ZAAG Cast-To Female are cemented in
place intra-orally on the prepared tooth root. (Fig. 30)
17. Snap a Denture Cap Male (stainless steel cap, nylon male and centering
sleeve) into each cemented coping for chairside pick-up into the denture. (fig.
31) lf processing of the denture component by the laboratory is desired, follow
steps 2-8 in "MALE PLACEMENT BYTHE LABORATORY."
J. RELINE ANDREBASE
1. Using a Trephine Bur, remove the entire Denture Cap Male component,
including metal cap and nylon male, from the overdenture, taking care not to
damage the metal housing.
2. Trim as much acrylic from the stainless steel denture cap as possible using a
coarse sand paper disk. It is not necessary to remove all acrylic from the
metal housing .
3. Place an Impression Male into each cemented female for reline impression
pick-up.
4. Take a reline impression. Using a Substitute Model Female as an analog,
reposition the denture components into the overdenture following the steps in
"MALE PLACEMENT BY THE LABORATORY".
NOTE: Extra centering sleeves are provided in the ZAAG attachment kits to
eliminate movement of the Denture Cop Mole component during processing.
HYGIENE AND MAINTENANCE
Experts recommend that overdenture abutments should be brushed at least once
a day with a gel toothpaste to remove plaque and to stimulate gingival tissues,
followed by applying a 0.4% Stannous Fluoride gel.
The patient should be instructed to periodically visit their dentist for professional
cleanings and attachment evaluation. Use plastic instruments for scaling the
attachments. Do not use metal instruments which may create scratches.
RETURN POLICY
Authorization for returns must be received from ZEST Anchors prior to the return of any product. Shipping
charges must be prepaid by the customer for ZEST Anchors to accept any return shipment. Returned products
may be subject to a restocking fee. Only merchandise returned in resaleable condition will be accepted for credit
if returned within 90 days of purchase. Returns will not be accepted after 90 days of purchase. Non-returnable
items include: merchandise retained beyond any expiration date noted on the packaging, products with broken
seals or missing parts, used, damaged or obsolete products and special order implant abutments.
WARRANTY
ZEST Anchors provides a limited warranty for its products, to the original purchaser, to be free from defects in
workmanship and materials under normal use for a period of one year from the date of purchase . ZEST Anchors
will, at its option, substitute the returned product that proves defective with a similar product, free of charge.
ZEST Anchors continually strives to improve its products, therefore, reserves the right to improve, modify or
discontinue products at any time without notice or incurring obligation. Purchaser assumes all risks and liability
resulting from the use of ZEST Anchors products whether used separately or in combination with other products
not of ZEST Anchors manufacture.
!"#$%T%'(%)%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
OUS&%V@9$<@=#$%!G":$H%+6:'9=@='H%,3%WOUOW%1X3%
K&M%TSUJTQPJTTQQ%
%
1FXF%!"7$97%.'F%RHQ&THRTU%
8
533? %@6%"%<$#@67$<$=%7<"=$E"<Y%'(%5$67%/!%-'G=@9#6H%44,%
%
%
%
%
%
%
%
%
%
%
4QUU&J*2%B+ZF%[%O\&U
%
!"#$%)%'(%)%
%
%
*+,-./01+%23.134%
%
!""#$%&'()"*+%"++",-'.*+%/0/+.'%
%
%
/2!56*3.*7%*89:%;'<=>$?@%<'?@"9?:%@8$%>':@%<=AA$?@%9?:@A=<@9'?:B%!C$":$D%A$";%"?;%A$@"9?B%
%
1./,2&(+&3*7%1?9E$A:"C%89?#$D%A$:9C9$?@%"@@"<8>$?@%('A%$?;':$'=:%9>FC"?@:B%
%
"++",-'.*+%,3'(3*.*+%321.2%*4'5.2/%
%
!A';=<@%?=>G$A:%'(%H33I%/>FC"?@%3G=@>$?@:%E$AJ%K9@8%9>FC"?@%@JF$D%;9">$@$A%"?;%@9::=$%<=((%8$9#8@B%
,"CC%H$:@%3?<8'A:%K9@8%@89:%9?('A>"@9'?%"E"9C"GC$%@'%FC"<$%J'=A%'A;$AB%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
!"#$%&%'(%)%
%
%INDICATIONS
%The ZAAG Implant Anchor is appropriate for use with overdentures or partial dentures, retained in whole or in
part, by endosseous implants in the mandible or maxilla.
%
CONTRAINDICATIONS
%Not appropriate where a totally rigid connection is required.
%CAUTION
%Federal (U.S.A.) law restricts this device to sale by or on the order of a licensed dentist.
FEATURES
%
1. INTRA-GINGIVAL CONNECTION: The attachment connection is low within the mucosa.
%
2. ROTATIONAL PIVOTING ACTION: During masticatory function , the ball-and-socket design lets the
% prosthesis hinge and move vertically.
3. NYLON INTERFACE: The slightly-flexible nylon male cushions occlusal shock and avoids the hard metal to-
% metal contact of other attachments.
%4. TITANIUM NITRIDE COATING: The Titanium alloy abutment is coated with a gold colored , wear resistant
coating that is three times harder than the metal itself and extremely bio-compatible.
5. USE WITH NON-PARALLEL IMPLANTS:
a. Pivoting Male: The ZAAG nylon male in the full size Denture Cap pivots up to 10 degrees in any direction
to compensate for minor mis-alignment of implants. (NOTE: The nylon male does not pivot in the ST
Denture Cap).
b. Angle Correction: The patented taper lock design for ZAAG angled inserts of 15 and 25 degrees allows
easy correction of divergent implants without the need for cementing.
c. Abutment Access: Once in place, the completed angle abutment still allows access for removal with the
hex tool at any future time.%
A. PLACEMENT OF THE ZAAG IMPLANT ABUTMENT
1. Prepare and measure study casts to determine the space available for the
female/male assembly. The full size ZAAG Denture Cap Male extends 3.1mm
above the ZAAG Abutment. The ZAAG ST Cap Male extends just 2.0mm
above the female for use when lack of occlusal space is a problem. (Fig. 1)
2.When selecting the proper ZAAG Abutment , match the threaded abutment
with the implant brand and diameter being used. Then, measure the tissue
thickness from the apical rim of the implant body to the crest of the gingiva.
Choose the closest corresponding tissue cuff height available. When fully
threaded into the implant, the top of the ZAAG Abutment should be level with
the surrounding tissue to achieve full stress reducing ability of the attachment.
(Fig. 2)
3. After the secondary gingival healing period is complete, remove the healing
cuff according to instructions provided by the manufacturer of the implant
system being used.
4. It is imperative that all bone and soft tissue be removed from the superior
aspect of the implant body to guarantee complete seating of the ZAAG
Abutment.%
!"#$%L%'(%)%
%
5. A .050 (1.25mm) Hex Tool (#4390) is used to thread the ZAAG Abutment into
the implant. The stainless steel tool has a white Teflon sleeve that slides
down and snaps into the attachment to hold it while delivering it to the implant
site and starting the thread. (Fig. 3)
NOTE: The use of a Torque Wrench with a .050 Hex Insert (#4936) can be used
to achieve the maximum seating force of 20N-cm (1 3/4 inch lb.) that will help
prevent screw loosening.
6. When placing multiple attachments, snap a Parallel Post into each seated
abutment to make sure the parallelism between implants is within 10 degrees
of each other.
NOTE: If the divergence is greater than 10 degrees, use the ZAAG Angle
Correction system to correct the alignment of the implants.
7. If a change in tissue height occurs later, it can be accommodated by
unthreading the ZAAG Abutment and replacing it with a different cuff height.
B. PLACEMENT OF THE ZAAG ANGLE CORRECTION SYSTEM
1. Using the Thread Pattern Chart , choose one of the four thread s on the
titanium Alignment Pin which matches the type of implant being used.
2. Thread the Alignment Pin by hand directly into the divergent implant (or
implant analog on a stone model) being careful not to cross-thread the pin.
Place the stainless steel Angle Measurement Guide behind the Alignment Pin,
level with the path of prosthesis insertion, to determine the divergence in
degrees. (Fig.4) An additional Alignment Pin can be placed into an adjacent
non-divergent implant to determine the difference in the angle between it and
the divergent implant.
WARNING: IF THE ALIGNMENT PIN DOES NOT EASILY THREAD INTO AN
IMPLANT, DO NOT FORCE THE INSERTION.
3. Select the ZAAG Angle Insert (15 or 25 degrees) which most closely matches
the measured angle of divergence. The threaded Angle Abutment Base must
match the brand and diameter of implant fixture being used. Choose the
closest corresponding tissue cuff height available.
4. A .050 (1.25mm) Hex Tool (#4390) is used to thread the Abutment Base Cuff
into the implant. Note: The use of a Torque Wrench with a .050 Hex Insert
(#4936) can be used to achieve the 20N-cm of maximum seating force that
will help prevent screw loosening.
5. Snap a Parallel Post into the appropriate ZAAG Angle Insert (Fig. 5) and use
it as a handle to lightly place the insert into the Abutment Base.
6. Rotate the Parallel Post with attached Angle Insert until it is aligned with other
non-divergent implants and the planned path of prosthesis insertion. (Fig. 6)
7. Hold the ZAAG Angle Insert in the exact position and remove the Parallel
Post. Place the Tapper Tool with Delrin tip into the Angle Insert and use a
mallot to tap it several times. (Fig. 7) The patented taper design will
permanently fuse the insert together with the taper fit of the Abutment Base
without the need for cement. NOTE: The complete Angle Insert/Abutment
Base assembly can still be removed from the implant with the .050 hex
wrench if necessary.%
%
!"#$%M%'(%)%
%
C. ZAAG MALE PLACEMENT BY THE DENTIST
1. Insertion of the proper ZAAG Abutment at tissue level has been completed.
2. Insert a ZAAG Denture Cap Male (metal housing side first) into the ZAAG
Male Placement Tool (#4961). Use the tool to snap a male into each female.
(Fig.8) Check each male for proper retention, and verify that each centering
sleeve seats firmly against the abutment, maintaining the male in the center of
the flared opening. (Fig. 9)
NOTE: The Male Placement Tool is made for use only with the full size Denture
Cap Male and does not fit the short cap of the ST Implant Male.
3. Prepare a recess in the denture to accommodate the protruding ZAAG Male.
There must be no contact between the denture and the stainless steel cap. If
the denture rests on the metal cap, excess pressure on the implant will result.
4. Use the Chairside Dental Attachment Light Cure Kit (#9403) to light cure
bond the ZAAG Dentu re Cap Male into the denture (Fig. 10 and 11 ) or mix a
permanent self-curing acrylic and place a small amount in the recess of the
denture and around the top of the Denture Cap Male.
5. Insert the denture into position in the oral cavity. Guide the patient into
occlusion, maintaining a proper relationship with the opposing arch. Maintain
the denture in a passive condition, without compression of the soft
tissue, while the acrylic sets. Excessive occlusal pressure during the
setting time may cause tissue recoil against the denture base and could
contribute to dislodging and wear of the nylon males.
6. Remove the centering sleeve from the Denture Cap Male. Relieve the acrylic
over the entire implant attachment surface. There should be no contact
between the ZAAG Abutment and the acrylic saddle. Instruct the patient in the
path of insertion. Have the patient insert and remove the appliance several
times. The snap into retention should be accomplished by finger pressure
without the aid of the opposing teeth.
NOTE: Use a black Polishing Cap (#9001) to f it over and protect the ZAAG
nylon male from damage when polishing the denture or using a bur to
remove excess acrylic from around the male.
%
D. ZAAG MALE PLACEMENT BYTHE LABORATORY
In the Operatory:
1. Insertion of the proper ZAAG Abutment at tissue level has been completed.
2. Place the Impression Male into the ZAAG Abutment in the oral cavity. Make
sure the male is fully seated. (Fig. 12)
3. Take an impression, exercising caution not to compress the soft tissue. The
Impression Male is designed with minimum retention to be picked up with the
impression material.
!"#$%N%'(%)%
%
4. Snap an Implant Analog onto each Impression Male in the impression. The
Analog must not fall off when turned upside-down with vibration. (Fig. 13)
5. Pour the master cast. Upon separation, the Analog is a part of the master
cast in the exact position the ZAAG Abutment is in the mouth.
6. Before waxing and processing the appliance place a ZAAG Denture Cap into
each Analog in the master cast (Fig. 14). Make sure the male is fully seated.
The centering sleeve eliminates movement of the male during processing.
7. Complete the processing.
8. Remove the centering sleeve from the male and relieve the acrylic over the
entire implant attachment surface. There should be no contact between the
ZAAG Abutment and the acrylic saddle.
NOTE: Use a black Polishing Cap (#9001) to fit over and protect the ZAAG
nylon male from damage when polishing the denture or using a bur to
remove excess acrylic from around the male.
%
E. REPLACEMENT OF THE ZAAG MALE
The life expectancy of the ZAAG nylon male is between one and three years for
most patients. During this time the retention of the snap fit gradually diminishes
until a point where replacement is desired to return to the full retention of the
attachment.
The ZAAG Abutment has a wear resistant Titanium Nitride coating applied to
the attachment connection surface. This gold colored coating is three times
harder than the metal itself and is bio-compatible with the surrounding soft
tissue.
IMPORTANT NOTE: It is imperative that the nylon ZAAG male in the
existing metal Denture Cap be replaced with the exact same type. The
replacement males are not the same for the full size Denture Cap and the
ST (Short and Tough) Denture Cap.
F. HOWTO CHANGE THE ZAAG MALE USING THE DENTURE CAP TOOL
KIT (#9201)
NOTE: The following is the technique for replacement of ZAAG Males featuring
a "dome-shaped" cap only.
For replacement of ZAAG ST Males, a Denture Cap Tool Kit (#9201) and ST
Male Took Kit (#92 02, purchased separately) is required.
1. Using a lab handpiece, guide the Male Coring Tool over the nylon male and
core out the center post of the male at medium RPM. (Fig. 15)
NOTE: If too much heat is generated, the metal cap may melt the surrounding
denture resin and dislodge. A small amount of cold water will help keep the
metal cool while coring out the nylon male.
!"#$%O%'(%)%
%
2. The Seating Tool utilizes a threaded plastic insert with two (2) working ends.
Use the end without a slot, with the metal pin provided, to eject the cored
male post out of the Coring Tool. (Fig. 16)
3. Using a blade or explorer-like instrument, collapse the remaining plastic ring
into the open space created by the removal of the center post and lift it out.
(Fig. 17)
4. ZAAG Replacement Males fit into the end of the Seating Tool Insert without
a slot. (Fig. 18)
5. Use the Seating Tool to firmly push a ZAAG Replacement Male into the metal
Denture Cap. The replacement male must seat securely into place level with
the rim of the cap. (Fig. 19)
G. RELINE AND REBASE
1. Remove the entire Denture Cap component from the overdenture, taking care
not to damage the metal housing.
2. Trim as much acrylic from the stainless steel Denture Cap as possible using a
course sandpaper disk. It is not necessary to remove all acrylic from the metal
housing.
3. Place an Impression Male into each ZAAG Abutment for reline impression
pick-up.
4. Take a reline impression. Using an Implant Analog, reposition the denture
components into the overdenture following steps in "MALE PLACEMENT BY
THE LABORATORY (Section D)."
H. PATIENT CARE
Oral hygiene is vital to implant success. The implant abutments must be thoroughly cleaned daily. The use of a
soft nylon bristle or end-tufted toothbrush, and superfloss to polish the abutments should be taught. A
nonabrasive gel toothpaste and an irrigation system is recommended to keep the socket of the ZAAG
Abutment clean.
Patients should maintain a three to four month recall for cleaning and implant evaluation. The sulcus area
around the abutment is the primary area of concern. Use plastic instruments for scaling the abutments. Do not
use metal instruments which may create scratches on the abutment surface. Examine patients for signs of
inflammation around the abutments and for implant mobility. Use the Hex Tool to make sure the ZAAG
Abutment is tight before dismissal.
RETURN POLICY
Check with your distributor for their policy on returns.
WARRANTY
ZEST Anchors, LLC provides a limited warranty for its products, to the original purchaser, to be free from
defects in workmanship and materials under normal use for a period of one year from the date of purchase.
ZEST Anchors, LLC will, at its option, substitute the returned product that proves defective with a similar
product, free of charge.
ZEST Anchors, LLC continually strives to improve its products, therefore, reserves the right to improve, modify
or discontinue products and components at any time without notice or incurring obligation. Purchaser assumes
all risks and liability resulting from the use of ZEST Anchors, LLC products whether used separately or in
combination with other products not of ZEST Anchors, LLC manufacture.%
!"#$%P%'(%)%
%
!"#$%Q%'(%)%
%
LRP&%W9?$A9;#$%!C"<$D%+:<'?;9;'D%,3%XLRLX%1Y3%
Z&[%QPRSQNMSQQNN%
1BYB%!"@$?@%.'B%ODN&QDOQR%
\
H33I %9:%"%A$#9:@$A$;%@A";$>"A]%'(%H$:@%/!%-'C;9?#:D%44,%%%
%
%
%
4NRRLS*2%6+TB%U%LV&R%