TRIM CUTTER
Model 7-6
For more information about this model, see Bulletin 991.
CAPABILITIES
Materials
Paper, plastic film and foil trim
Trim Width max
7.5" (191 mm)
Caliper Range
0.25 mil to 20 mil
0.00025" to 0.02000"
0.0064 mm to 0.508 mm
Air Capacity
1,000 cfm 1,700 m3/hr
SHEAR-CUT ACTION FOR PAPER
AND TOUGH, THIN FILM AND FOIL
Top Performance
Model 7-6 offers proven BloApCo design with new,
innovative maintenance and operating features to achieve
higher performance and economy. Driven by a 1-hp electric
motor, the 7-6 is capable of accurately and consistently cuts
films as thin as 0.00025". Varied knife profiles make short
work of light paper, plastic film and foil trim up to 7.5"
(191mm) wide. Wear-resistant HCHC, NEOR and carbide
knives can be arrayed to match slitting equipment, reducing
multiple ribbons of trim, depending on weight and thickness,
for pneumatic conveying, baling, disposal or recycling.
Precise Operation
Easy Installation
Installation of a Model 7-6 trim cutter is quick and simple:
The cutter is factory-tested, tailored to your application, and
shipped completely assembled and ready to run.
Drive
V-Belt or Direct Drive
Cutting Action
Shear
Rotor speed
500 to 3,600 rpm
Weight
135 lbs. (61kg) with motor
Dimensions
L x W x H: 17" x 131/4" x 221/2"
(431.8 mm x 336.5 mm x 571.5 mm)
FEATURES
• Fast, easy setup
• Multiple knives: HCHC, NEOR, carbide-edge
• Class "O" tapered roller bearings
eliminate endplay and runout
• Rotor shaft supported by tapered roller
bearings maintains rotor stability for long life
• Open-rotor design facilitates free
passage of air and material
• Multiple mounting and drive arrangements
• Multiple flanged inlet, slip-fit outlet
positions
• 1 HP 3/60/460-volt TEFC motor is standard
OPTIONS
•
•
•
•
•
Class “OO” tapered roller bearings
Oil mist unit
Gear motor drive
Safety disconnect switch
Tandem rail mounting with
BloApCo material-handling fan
Tech Sheet 7-6
Cutting with one stationary bed knife and two rotating
knives, the 7-6 makes two cuts per revolution at speeds from
500 to 3,600 rpm and passes 1,000 cfm of air at a static
pressure loss of 1.5" wg. The split-housing feature permits
easy access to the cutting blades, permitting quick removal
for sharpening with no need for “in-body” rotor grinding.
Class “O” tapered roller bearings eliminate endplay and
runout problems, while the open rotor design allows fast, free
flow of cut material through the cutter housing.
Static Pressure Loss
1.5" wg. @ 5,000 fpm air velocity
Tech Sheet 7-6
Dimensions
Model 7-6
813
16
8316
478
478
438
6
A
INLET 4
1012
2212
22316
2
B
258
A
334 OUTLET
B
1912
1712
12
2116
6316
6316
15
16
578
1378
578
1134
1314
278
314
158
514
258
4
458
2516
214
5
8TYP.
158
734
5
8
TYP.
258
658
211
16
2516
838
334
258
611
16
1058
934
VIEW "A-A"
INLET
538
Ø 7/16 (4) HOLES
1/4-20 UNC
(6) HOLES
VIEW "B-B"
OUTLET
1/4-20 UNC
(6) HOLES
For more information about this model, see Bulletin 991.
®
Blower Application Company
N114 W 19125 Clinton Drive • P.O. Box 279 • Germantown, WI 53022-0279 • 800.959.0880 • 262.255.5580 • FAX: 262.255.3446 • [email protected] • bloapco.com