1/18/17
WOODEN WHISPER PLAY SYSTEMS
Heavy Duty Hardware Kit
15' x 14 1/2'
Kit Includes:
1
Illustrated Plans/Blueprint
1
Maintenance Info/Warranty Card
2
Sling Swings 125 lb.
6
3/8" Swing Hangers/Fasteners
2
Trapeze Rings
2
8' Poly Ropes
5
3/8x7 1/2” Carriage Bolt
4
3/8 x 7" Carriage Bolt
4
3/8 x 5 1/2" Carriage Bolt
14
3/8x5” Carriage Bolt
4
3/8 x 4" Carriage Bolt
Material Needed:
2
4x4x10'
8
4x4x8'
2
3x4x8’
1
2x6x12'
3
2x6x10'
1
2x4x8’
3
2x4x10”
2
5/4x6x10'
11
5/4x6x8'
1
1x4x8'
6
1
2
4
2
4
14
8
12
24
4
20
Poly Hanger Clamps
Vinyl Shade Wall
56 1/2 oz. Gusset
20 1/2 oz. Beam Stiffener
16" Tubular Steel Brace
13 1/2" Tubular Steel Brace
#14x 2 1/2” Pan Head Screw
#14x1” Pan Head Screw
#10 x 3/4" Pan Head Screw
#10 x 1 1/2" Pan Head Screw
3/8x5 1/2” Lag Screw
3/8 x 1 1/2" Lag Screw
4
8
2
33
2
34
76
150
8
25
29
8
5/16x3 1/2” Lag Screw
5/16 x 1 1/2" Lag Screw
3/8 x 3/4" Hex Head Bolt
3/8 Lock Washer
#10x4” Deck Screw
#8 or #9x 3" Deck Screw
#8 or #9x 2 1/2" Deck Screw
#8 or #9x 2" Deck Screw
3/8” Acorn Nut-Stainless
3/8 Hex Nut
3/8 USS Washer
Cable Ties 8“
4
20
8
3
3
2
4
2
2
6
8’
6
5/16” USS Washer
3/8” Small SAE Washer
5/16” Small SAE Washer
6” Joining Plate
4” Corner Brace
3” Corner Brace
54 1/2” Chain 800 lb.
21 1/2” Chain 800 lb.
2 1/2” Finish Nail
Spring Clips
Webbing
S Hook
Cut two into 9'5" lengths to be used for the Beam NOTE: Select crowned lumber for additional strength
Legs NOTE: Do NOT cut four Clubhouse Legs and four A-Frame Legs
Landscape Timber for A-Frame Anchors———-*Note 4x4 stock also acceptable
Cut one 66 3/4" Joist and one 61 3/4" Mid Joist
Cut three 66 3/4" Joist and three 41" Joist
Cut one 41" Brace and one 5 3/8" Deck Support Block plus one 34” Railing Tip: 2x6 Stock ripped in halfworks for 5 3/8” Block
Cut six 38 1/2” Rafter, four 24” Rafter Support and two 21 3/4” Mid Rafter support
Cut two 65 3/4" Sandbox and two 40" Sandbox
Cut ten 43 7/8" Decking , eight 41” Baluster, and four 37” Baluster
Cut two 34" Decking , four 3 1/2" Tube Support Block & four 2 1/4" Deck Support Block Tip: 5/4x6 Stock ripped in half works
for these components and is especially “Recommended” for the 3 1/2” Tube Support Block
2
1
7
2x2x8'
Cut three 16" Rope Ladder Rungs plus four 16” or longer Anchor Stake, if going into sand, etc. (2x4 Stock ripped is stronger)
3/4x10' Sch. 40 PVC Cut two 33 3/4" Shade Wall Tube
1x6x12’
Cut fourteen 71 3/4” Roof Board
Optional Materials Needed:
Tools Required:
Two 12" Bar Clamps
6' Steel Fence Post (& Driver)
Carpenters Square
8' Timber (s) for bracing
Wrench (5/8”, 9/16", 1/2")
2
4x4x12’
Tape Measure
Phillips Bits #2 & #3
Metal File (or 1/4" round-over bit)
Hammer + Sledge Hammer
Shovel
To make a 12’ Beam
1/2" Drill Bit (omit if using Ladder)
3/8" Extended 12" Drill Bit
1/4" Extended 12" Drill Bit
7/32 or 1/4" Drill Bit
11/64" Drill Bit
Vice Grip or Bolt Gripping Tool (above)
1 3/8" Spade or Forstner Bit
1 1/16" or 1 1/8" Spade or Forstner Bit
7/8" Spade or Forstner Bit
3/16” Drill Bit
1/8" Drill Bit
5/16” Drill Bit
Drill
Tape
Level
Bungee Cord
Saw
Ladder