Perlok
CR 1.2
Base
Sheet
Fastener
PERLOK
CR
1.2
BASE
SHEET
FASTENER
Secure Base Sheets to Lightweight Insulating Concrete or Gypsum
Lightweight
insul. concrete
or gypsum
designed to secure base sheets to lightweight insulating concrete or gypsum
Product
Description
Product
Description
u THE PERLOK
CR 1.2 BASE SHEET FASTENER is a one piece unit, precision
u The
PERLOK CR 1.2 Base Sheet Fastener is a one piece unit,
formed from G-90 galvanized steel, coated with CR. A Pogo Stick or wooden
precision formed from G-90 galvanized steel, coated with CR.
mallet should be used to install the fastener. This fastener is designed to
A Pogo Stick or wooden mallet should be used to install the
secure base sheets to a minimum 1.25” thickness of poured lightweight
fastener. This fastener is designed to secure base sheets to
insulating concrete or various gypsums.
a minimum 1.25” thickness of poured lightweight insulating
THE PERLOKconcrete
CR 1.2 BASE
SHEET
FASTENER is Factory Mutual and Dade
or various
gypsums.
County approved.
The PERLOK CR 1.2 Base Sheet Fastener is Factory Mutual
and Dade County approved.
UsesUses
u THE PERLOK
CR PERLOK
1.2 BASECR
SHEET
FASTENER
designedis to
secure base
sheets to
u The
1.2 Base
SheetisFastener
designed
to secure
lightweight insulating
concrete
or various gypsums.
base sheets
to lightweight
insulating concrete or various
gypsums.
Special Characteristics
u THE
PERLOKCharacteristics
CR 1.2 BASE SHEET FASTENER is F.M. and Dade County approved.
Special
u PERLOK CR
1.2 BASE SHEET FASTENER & Plate exceeds F.M. Class I-90 Wind Uplift requirements when
u The PERLOK CR 1.2 Base Sheet Fastener is F.M. and Dade County approved.
installed in accordance with I-90 nailing pattern.
u PERLOK CR 1.2 Base Sheet Fastener & Plate exceeds F.M. Class I-90 Wind Uplift requirements
u Assembled PERLOK
CR 1.2 BASE SHEET FASTENER greatly reduces installation time and labor cost.
when installed in accordance with I-90 nailing pattern.
u Entire fastener
is CR coated to prevent in-place corrosion.
u Assembled PERLOK CR 1.2 Base Sheet Fastener greatly reduces installation time and labor cost.
Coating u Entire fastener is CR coated to prevent in-place corrosion.
A special
corrosion resistant CR coating exhibits less than 15% red rust after 30 Kesternich cycles. CR is a unique
Coating
epoxy based coating specifically applied to optimize resistance to corrosion. This special coating exceeds F.M.
A special corrosion resistant CR coating exhibits less than 15% red rust after 30 Kesternich cycles. CR
Approval Standard 4470.
is a unique epoxy based coating specifically applied to optimize resistance to corrosion. This special
coating exceeds F.M. Approval Standard 4470.
Rev. 12/2010
* This document cancels and replaces any other document published previously.
All values shown are nominal and subject to normal manufacturing tolerances.
* This document cancels and replaces any other document published previously.
All values shown are nominal and subject to normal manufacturing tolerances.
Application
Lightweight
insulating concrete or gypsum must be surface dry and reasonably smooth prior to roofing. For the
Application
best performance, the fastener should always be installed perpendicular to the substrate.
Lightweight insulating concrete or gypsum must be surface dry and reasonably smooth prior to
Assembled PERLOK
CRFor
1.2 the
BASE
SHEET
FASTENER is
a GALVALUME®
2 .75” plate.
roofing.
best
performance,
theassembled
fastener with
should
always be installed
perpendicular to the
Use the Pogo substrate.
Stick to install the fastener.
Assembled PERLOK CR 1.2 Base Sheet Fastener is assembled with a GALVALUME® 2 .75” plate.
F.M. Approved
Use the Pogo Stick to install the fastener.
For increased wind uplift resistance and high-wind applications, it is required that the PERLOK CR 1.2 BASE
F.M. Approved
SHEET FASTENER with the PERLOK Base Sheet Plate be used in accordance with an approved I-90 nailing
For increased wind uplift resistance and high-wind applications, it is required that the PERLOK CR
pattern.
1.2 Base Sheet Fastener with the PERLOK Base Sheet Plate be used in accordance with an approved
Note: On reroofing
applications,
I-90 nailing
pattern.prior to job start, roof should be inspected or tested to determine the pullout
values.
Note: On reroofing applications, prior to job start, roof should
be inspected or tested to determine the pullout values.
Physical Data
DataHead Size: 1.125” x 1” Leg Length: 1.2”
Base Physical
Sheet Fastener:
Pub # 504 – 03/05
Base .014
Sheet
Fastener: Head Size: 1.125” x 1” Leg Length: 1.2”
Material Thickness:
nominal
Material
Thickness:
nominal
Material: G-90
galvanized
with CR.014
coating
Material: G-90 galvanized with CR coating
Plate:
Plate:
Diameter: 2.75”
Material: GALVALUME®
Diameter:
Material: GALVALUME®
Material Thickness:
.0142.75”
nominal
Material Thickness: .014 nominal
Packaging:
Packaging:
Assembled: 1000 per carton Shipping Weight: 37 lbs.
Assembled:
1000 per carton Shipping Weight: 37 lbs.
Standard: 1000 per carton Shipping Weight: 16 lbs.
Standard:
1000 per carton Shipping Weight: 16 lbs.
Plate: 1000 per carton Shipping Weight: 20 lbs.
Plate:
1000 per carton Shipping Weight: 20 lbs.
MSDS Available on Request at (800) 727-9872 or at www.derbigum.com.
PERFORMANCE Roof Systems, Inc.
4800 Blue Parkway
4800 Blue Parkway
Kansas City, MO 64130
Kansas City, MOPhone
64130- 800.727.9872 – Fax 816.921.5007
E-mail /:Fax:
[email protected]
Phone: 800.727.9872
816.924.1542 – WWW.DERBIGUM.COM
E-mail: [email protected] Web: www.derbigum.com
WWW.DERBIGUM.COM
WWW.DERBIGUM.COM
Perlok
CR 1.7
Base
Sheet
Fastener
PERLOK
CR
1.2
BASE
SHEET
FASTENER
Secure Base Sheets to Lightweight Insulating Concrete or Gypsum
Lightweight
insul. concrete
or gypsum
designed to secure base sheets to lightweight insulating concrete or gypsum
Product
Description
Product
Description
u THE PERLOK
CR 1.7 BASE SHEET FASTENER is a one piece unit, precision
u The
PERLOK CR 1.2 Base Sheet Fastener is a one piece unit,
formed from G-90 galvanized steel, coated with CR. A Pogo Stick or wooden
precision formed from G-90 galvanized steel, coated with CR.
mallet should be used to install the fastener. This fastener is designed to
A Pogo Stick or wooden mallet should be used to install the
secure base sheets to a minimum 2” thickness of poured lightweight
fastener. This fastener is designed to secure base sheets to
insulating concrete or various gypsums.
a minimum 1.25” thickness of poured lightweight insulating
THE PERLOKconcrete
CR 1.7 BASE
SHEET
FASTENER is Factory Mutual and Dade
or various
gypsums.
County approved.
The PERLOK CR 1.2 Base Sheet Fastener is Factory Mutual
and Dade County approved.
UsesUses
u THE PERLOK
CR PERLOK
1.7 BASECR
SHEET
FASTENER
designedis to
secure base
sheets to
u The
1.2 Base
SheetisFastener
designed
to secure
lightweight insulating
concrete
or various gypsums.
base sheets
to lightweight
insulating concrete or various
gypsums.
Special Characteristics
u THE
PERLOKCharacteristics
CR 1.7 BASE SHEET FASTENER is F.M. and Dade County approved.
Special
u PERLOK CR
1.7 BASE SHEET FASTENER & Plate exceeds F.M. Class I-150 Wind Uplift requirements when
u The PERLOK CR 1.2 Base Sheet Fastener is F.M. and Dade County approved.
installed in accordance with FM requirements.
u PERLOK CR 1.2 Base Sheet Fastener & Plate exceeds F.M. Class I-90 Wind Uplift requirements
u Assembled PERLOK
CR 1.7 BASE SHEET FASTENER greatly reduces installation time and labor cost.
when installed in accordance with I-90 nailing pattern.
u AssembleduBase
Sheet Fasteners are packaged for easy handling on the roof.
Assembled PERLOK CR 1.2 Base Sheet Fastener greatly reduces installation time and labor cost.
u Entire fastener
is CR coated to prevent in-place corrosion.
u Entire fastener is CR coated to prevent in-place corrosion.
Coating
Coating
A special corrosion
resistant
CR coating
exhibits
less than
15% red
rust
after
30 Kesternich
cycles.
CR is a unique
A special
corrosion
resistant
CR coating
exhibits
less
than
15%
red rust after
30 Kesternich
cycles. CR
epoxy based coating
specifically
applied
to
optimize
resistance
to
corrosion.
This
special
coating
exceedsThis
F.M.special
is a unique epoxy based coating specifically applied to optimize resistance to corrosion.
Approval Standard
4470.
coating
exceeds F.M. Approval Standard 4470.
Application
Application
Rev. 12/2010
* This document cancels and replaces any other document published previously.
All values shown are nominal and subject to normal manufacturing tolerances.
* This document cancels and replaces any other document published previously.
All values shown are nominal and subject to normal manufacturing tolerances.
Lightweight insulating
concrete
or gypsum
must or
be surface
andbe
reasonably
smooth
to roofing.
For theprior to
Lightweight
insulating
concrete
gypsumdry
must
surface dry
andprior
reasonably
smooth
best performance,
the fastener
always be installed
perpendicular
the substrate.
roofing.
For the should
best performance,
the fastener
shouldtoalways
be installed perpendicular to the
substrate.
Assembled PERLOK
CR 1.7 BASE SHEET FASTENER is assembled with a GALVALUME® 2 .75” plate.
Assembled PERLOK CR 1.2 Base Sheet Fastener is assembled with a GALVALUME® 2 .75” plate.
Use the Pogo Stick to install the fastener.
Use the Pogo Stick to install the fastener.
I-150 F.M. Approved
F.M. Approved
The CR BaseFor
Sheet
Fastener
is FM
to and
I-150
with certain
base sheet
insulating
concrete
increased
wind
upliftapproved
resistance
high-wind
applications,
it isand
required
that the
PERLOK CR
combinations.1.2 Base Sheet Fastener with the PERLOK Base Sheet Plate be used in accordance with an approved
I-90start,
nailing
pattern.
Note: Prior to job
contact
DERBIGUM Americas, Inc. to determine the correct nailing pattern. On reroofing
Note:
reroofi
ng should
applications,
prior toorjob
start,
shouldthe pullout values.
applications, prior
to On
job start,
roof
be inspected
tested
to roof
determine
be inspected or tested to determine the pullout values.
Physical Data
DataHead Size: 1.125” x 1” Leg Length: 1.75”
Base Physical
Sheet Fastener:
Pub # 504 – 03/05
Base .014
Sheet
Fastener: Head Size: 1.125” x 1” Leg Length: 1.2”
Material Thickness:
nominal
Material
Thickness:
nominal
Material: G-90
galvanized
with CR.014
coating
Material: G-90 galvanized with CR coating
Plate:
Plate:
Diameter: 2.75”
Material: GALVALUME®
Diameter:
Material: GALVALUME®
Material Thickness:
.0142.75”
nominal
Material Thickness: .014 nominal
Packaging:
Packaging:
Assembled: 500 per carton Shipping Weight: 21 lbs.
Assembled:
1000 per carton Shipping Weight: 37 lbs.
Standard: 1000 per carton Shipping Weight: 20 lbs.
Standard:
1000 per carton Shipping Weight: 16 lbs.
Plate: 1000 per carton Shipping Weight: 20 lbs.
Plate:
1000 per carton Shipping Weight: 20 lbs.
MSDS Available on Request at (800) 727-9872 or at www.derbigum.com.
PERFORMANCE Roof Systems, Inc.
4800 Blue Parkway
4800 Blue Parkway
Kansas City, MO 64130
Kansas City, MOPhone
64130- 800.727.9872 – Fax 816.921.5007
E-mail /:Fax:
[email protected]
Phone: 800.727.9872
816.924.1542 – WWW.DERBIGUM.COM
E-mail: [email protected] Web: www.derbigum.com
WWW.DERBIGUM.COM
WWW.DERBIGUM.COM
Perlok Standard
Roofing Fastener
Designed to Secure Insulation and Roofing to Steel & Wood Decks
Product Description
uThe PERLOK STANDARD ROOFING FASTENER is designed to secure insulation and roofing
membrane to standard steel (18 ga. – 24 ga.) and wood. It is available in lengths from
1 5/8’’–8’’. The PERLOK STANDARD ROOFING FASTENER is Factory Mutual and Dade
County approved. Use with a PERLOK 3’’ steel plate.
Uses
uThe PERLOK STANDARD ROOFING FASTENER is designed to secure insulation and roofing
membrane to steel and wood decks.
Special Characteristics
u
u
u
u
Heavier shank & thread diameters than most “standard” roofing fasteners.
Deep buttress thread for high pullout resistance.
Extra sharp spade point for quick installation in new or reroof applications.
Available with hex head or #3 phillips truss head.
Coating
A special corrosion resistant CR coating exhibits less than 15% red rust after 30 Kesternich cycles. CR
is a unique epoxy based coating specifically applied to optimize resistance to corrosion. This special
coating exceeds F.M. Approval Standard 4470.
Application
The PERLOK STANDARD ROOFING FASTENER must penetrate steel decks a minimum of 3/4’’, wood plank
decks a minimum of 1“ and 1/2“ through the underside for plywood decks. Using a screwshooter, drive the
fastener until a slight depression is seen around the plate, or with very rigid insulation boards, watch for the
plate to dimple.
Note: Care must be taken not to overdrive the fastener and fracture the skin of the insulation. Fastener must be
tight enough so that the plate doesn’t turn. For steel decks, Factory Mutual requires that the fastener penetrate
the deck at the top fl ute. To speed installation, this fastener is also available as a labor saving preassembled
screw and plate. See PERLOK Preassembled screw and 3“ steel plate.
* This document cancels and replaces any other document published previously.
All values shown are nominal and subject to normal manufacturing tolerances.
Product Information
Rev. 12/2010
The data below is constant for each PERLOK
STANDARD ROOFING FASTENER.
Thread Diameter: Head Diameter:
Truss Head: Hex Head: Head Style: Coating: .220
Length
Thread
Length
Packaging
Weight
55/8”
Full
1000
12 lb
2 /4 ”
Full
1000
16 lb
2 /8 ”
Full
1000
19 lb
31/4 ”
3”
1000
22 lb
1
.435
.390
#3 Phillips
Truss Head*
1/4’’ Hex Head*
CR
*#3 phillips bit or hex head drive included in
each carton.
MSDS Available on Request at (800) 727-9872 or at
www.derbigum.com.
7
33/4 ”
3”
100
25 lb
41/2 ”
3”
1000
29 lb
5”
3”
1000
35 lb
6”
4”
1000
42 lb
7”
4”
1000
48 lb
8”
4”
1000
54 lb
WWW.DERBIGUM.COM
4800 Blue Parkway
Kansas City, MO 64130
Phone: 800.727.9872 / Fax: 816.924.1542
E-mail: [email protected] Web: www.derbigum.com
Perlok Dual Fastener
Roof Insulation and Membrane Fastener for Base Ply, Recover Board and Insulation
Product Description
uPERLOK DUAL FASTENER is a roof insulation and
membrane fastener for base ply, recover board and
insulation to wood fiber or poured gypsum decks.
uComposition: Factory pre-assembled components
consisting of:
TUBE: Precision formed from Galvanized (G-90) coated
steel to prevent corrosion. The tube is shaped to easily
penetrate decking and exiting membranes.
DISK: Precision formed from Galvalume (AZ-55) coated
steel to prevent corrosion. The disk is securely clamped
to the tube, 2.7” diameter, rib reinforced to resist
cupping.
LOCKING STAPLE: Precision formed from high tensile
steel wire.
Physical Data
Available Lengths
1.4”
1.8”
2.8”
3.8”
4.8”
Packaging
1.4”, 1.8”, 2.8”, and 3.8”
PERLOK DUAL FASTENER
500 per Carton
4.8” PERLOK DUAL FASTENER
250 per Carton
* This document cancels and replaces any other document published previously.
All values shown are nominal and subject to normal manufacturing tolerances.
MSDS Available on Request at (800) 727-9872 or at www.derbigum.com.
Rev. 12/2010
WWW.DERBIGUM.COM
4800 Blue Parkway
Kansas City, MO 64130
Phone: 800.727.9872 / Fax: 816.924.1542
E-mail: [email protected] Web: www.derbigum.com
Installation Method
uDrive fastener perpendicular to roof deck seating cap flash with roofing surface. Once tube is set, drive
the locking staple thru the tube/disk unit into the deck until the top of the staple is flush with the cap (see
illustration). The PERLOK DUAL FASTENER should always be embedded into the structural roof deck to a
depth of at least 1”.
u Operation: When locking staple is driven, its dual wire legs diverge anchoring the fastener in place
(see illustration on first page). Uplift resistance may vary depending on the density and integrity of the
substrate.
u Field Testing: On-site withdrawal testing should always be performed to evaluate the ability of the roofing
substrate to satisfactorily accept and retain fasteners. Such testing may alter fastener selection and modify
applicable fastening patterns.
u Fastening Patterns: PERLOK DUAL FASTENER density and spacing vary depending on applicable uplift
requirements. Local codes, governing Approval bodies, Derbigum membranes, and individual roof deck
manufacturers all may have specific requirements that need to be addressed prior to beginning any roofing
project. The following illustrates typical Factory Mutual recommended fastening patterns accepted by
DERBIGUM Americas, Inc. and roof deck manufacturers.
Fastening Guide for Base Sheets
The following base ply attachment meets FM Class
1-60, 1-75 or 1-90 Windstorm Classification.
DERBIGUM GP/XPS, Derbibase Ultra, Derbibase,
PRS Glass Base Sheet, or Glass Ply IV/VI is fastened
in the field of the roof with PERLOK DUAL FASTENER
installed 9” on center in the side laps and 18” on
center staggered in 2 rows, equally spaced, between
the base ply side laps. Approximately 86 fasteners
per square (100 ft.2).
Fastening Guide for Recovery Board and Insulation
The following fastening attachment meets FM Class
1-90 Windstorm Classification.
Approved insulation boards listed in FM Global
Approval Guide or Roofnav for use with Derbigum
roof systems is fastened with 8 Perlok Dual Fasteners
per 4’ x 4’ board in a diamond in a box pattern. (1
fastener per 2 ft.2).
Perlok Heavy Duty
Roofing Fastner
Designed to Secure Insulation and Roofing to Steel & Wood Decks
Product Description
uThe PERLOK HEAVY DUTY ROOFING FASTENER is designed to secure insulation and roofing
membrane to heavy steel (18 ga.– 20 ga.). It is available in lengths from 1 1/4” - 26”. The
PERLOK HEAVY DUTY ROOFING FASTENER is Factory Mutual and Dade County approved.
Uses
uThe PERLOK HEAVY DUTY ROOFING FASTENER is designed to secure insulation and roofing
membrane to heavy steel and wood decks.
Special Characteristics
u Heavier shank & thread diameters than most “heavy duty” roofing fasteners.
u Deep thread for high pullout resistance.
u Extra sharp spade point for quick installation in new or reroof applications.
Coating
A special corrosion resistant CR coating exhibits less than 15% red rust after 30 Kesternich cycles. CR is a unique
epoxy based coating specifi cally applied to optimize resistance to corrosion. This special coating exceeds F.M.
Approval Standard 4470.
Application
The PERLOK HEAVY DUTY ROOFING FASTENER must penetrate the deck a minimum of 3/4”. Using a
screwshooter, drive the fastener until a slight depression is seen around the plate, or with very rigid insulation
boards, watch for the plate to dimple. Note: Care must be taken not to overdrive the fastener and fracture the
skin of the insulation. Fastener must be tight enough so that the plate doesn’t turn.
Use with a PERLOCK 3” steel plate. For best installation results, use a variable speed 0-2500 rpm screw gun.
Product Information
* This document cancels and replaces any other document published previously.
All values shown are nominal and subject to normal manufacturing tolerances.
The data provided is constant for each PERLOK
HEAVY DUTY ROOFING FASTENER.
Rev. 12/2010
Length
Thread
Length
Packaging
Weight
11/4”
12 lb
Full
1000
3
1 /4 ”
Full
1000
16 lb
Thread Diameter: .245
2”
Full
1000
18 lb
Shank Diameter: .190
3”
Full
1000
26 lb
Head Diameter:
.435
4”
3”
1000
34 lb
Head Style:
#3 Phillips
Truss Head**
5”
4”
500
22 lb
6”
4”
500
26 lb
Coating: CR
7”
4”
500
30 lb
8”
4”
500
34 lb
**#3 phillips bit or hex head drive included
in each carton
MSDS Available on Request at (800) 727-9872 or at
www.derbigum.com.
9”
5”
500
37 lb
10”
5”
500
40 lb
11”
5”
500
44 lb
12”
5”
250
25 lb
14”
5”
250
29 lb
5”
250
37 lb
16”
Longer lengths upon request.
Call DERBIGUM for information.
WWW.DERBIGUM.COM
4800 Blue Parkway
Kansas City, MO 64130
Phone: 800.727.9872 / Fax: 816.924.1542
E-mail: [email protected] Web: www.derbigum.com
Perlok Extra Heavy Duty
Roofing Fastner
Designed to Secure Roofing Materials to Light Gauge Steel, Roof Decks
Product Description
uThe PERLOK EXTRA HEAVY DUTY ROOFING FASTENER is a specialized, high performance
fastener designed to secure roofing materials to certain light gauge steel. O.S.B., or aluminium
roof decks.
Special Characteristics
u Oversized heavy shank and thread diameters for enhanced pullout resistance in light gauge steel
roof decks.
u Deep buttress threads further increase pullout resistance.
u Miniature drill point penetrates decks quickly and contributes to exceptional resistance to backout
as well as pullout
Coating
Perlok CR-10 corrosion resistant coating exhibits less than 15% red rust after 30 Kesternich cycles. CR-10
coating exceeds F.M. Approval Standards 4470.
Application
The PERLOK EXTRA HEAVY DUTY ROOFING FASTENER should always be tested on site by an Olympic
representative to determine performance and proper installation procedure. Call Olympic to schedule testing.
Plates & Accessories
A variety of plates are available. Contact Perlok to determine the appropriate plate for your application.
Product Information
* This document cancels and replaces any other document published previously.
All values shown are nominal and subject to normal manufacturing tolerances.
Cat. No.
Rev. 12/2010
Length
Thread
Length
Packaging
Weight
The data provided is constant for
each PERLOK EXTRA HEAVY DUTY
ROOFING FASTENER.
EHD002
2”
Full
1000
20 lb
EHD003
3”
Full
1000
29 lb
EHD004
4”
3”
1000
38 lb
Head Diameter: .435
EHD005
5”
4”
1000
47 lb
Thread Diameter: .275
EHD006
6”
4”
1000
56 lb
Head Style:
#3 Phillips
Truss
EHD007
7”
4”
500
34 lb
EHD008
8”
4”
500
38 lb
Coating: CR-10
EHD0010
10”
4”
500
47 lb
EHD0012
12”
4”
500
56 lb
EHD0014
14”
4”
500
32 lb
EHD0016
16”
4”
500
38 lb
MSDS Available on Request at (800) 727-9872 or at www.derbigum.com.
WWW.DERBIGUM.COM
4800 Blue Parkway
Kansas City, MO 64130
Phone: 800.727.9872 / Fax: 816.924.1542
E-mail: [email protected] Web: www.derbigum.com