www.american-image.com
Spin ‘N’ Win™ Prize Wheel Kit
Congratulations on the purchase of your
Spin ‘N’ Win™ Prize Wheel Kit.
Owner’s Manual
Includes:
Parts List
Assembly Instructions
Disassembly Instructions
Storage Instructions
Care Instructions
Warranty Information
Please read all of the information carefully and
contact your distributor or supplier with any issues.
Parts List
E
5/16th" Wrench
1/2" Wrench
1/8th" Allen Wrench
F
G
3/16th" Allen Wrench
A
H
I
J
K
L
M
N
D
B
C
O
A - Stand
B - Extension Legs (3)
C - Pointer Arm
D - Wheel
E - 3-1/2" Wheel Bolt
F - 1/2" Wheel Spacers (2)
G - Wheel Washer
H - 5/16" Wheel Nut
I - 1/2" Arm Bolts (2)
J - 3/8" Pointer Bolts (2)
K - Small Nuts (4)
L - Small Endcaps (4)
M - Pointer
N - Magnetic Center Cover
O - Soft Carry Case
(case not to scale)
800-676-3976 • 425-556-9511 • fax 425-556-9611 • 4054 148th Ave. NE • Redmond, WA 98052
Assembly Instructions
EXTENSION LEGS
(1) Remove Rubber Feet from the three Stand
EXTENSION
LEGSExtension
Legs and place1)them
on the three
Legs (on opposite ends from the Pins).
(Applies to Floor Models only. For Tabletop Models, skip
1) EXTENSION
LEGS
this
stageExtension
and proceed
to THE into
STAND.)
(2) Insert
Legs
the Stand Legs
by (Applies
pressing
in each
Pin
and
rotating to
secure
it
to Floor
Models
only.
For
Models,
(1) Remove
Rubber
Feet
from
theTabletop
three
Stand
Legsskip
through
the
hole
on
each
Stand
Leg.
this
to THE
STAND.) Legs (on
and stage
place and
themproceed
on the three
Extension
opposite ends from the Pins).
(1) Remove Rubber Feet from the three Stand Legs
and
placeExtension
them on theLegs
threeinto
Extension
(2) Insert
the StandLegs
Legs(on
by
opposite
ends
from
the
Pins).
pressing in each Pin and rotating to secure it through
the hole on each Stand Leg.
(2) Insert Extension Legs into the Stand Legs by
pressing in each Pin and rotating to secure it through
the hole on each Stand Leg.
STAND
LEGS
EXTENSION
LEGS
PIN
RUBBER
FEET (3)
PIN
RUBBER
FEET (3)
2) THE STAND
THE STAND
(1) Set the Stand upright on its Rubber Feet (with or
2) THE STAND
(1)without
Set the
Stand upright
on its Rubber
Extension
Legs, depending
on model).Feet
(with or without Extension Legs, depending on
(1)
upright
its latch
Rubber
Feet (with
model).
(2) Set
Freethe
theStand
Support
Armonand
it securely
intoorthe
without
Extension
Legs,
depending
on
model).
slot on the Crossbar.
(2) Free the Support Arm and latch it securely
Free
the
Support
Arm
latch
it securely
(3)the
Attach
the
Pointer
Armand
to the
Arm
Plate (oninto
thethe
into(2)
slot
on
the Crossbar.
slot
on
the
Crossbar.
Stand) using the two 1/2" Arm Bolts and two of the
Nuts.
theArm
Pointer
(with the
curved
(3)Small
Attach
thePosition
Pointer
to Arm
the Arm
Plate
(3)
Attach
the
Pointer
Arm
to
the
Arm
Plate
(on
the
facing front)
against
the Arm
up
(onend
theup,
Stand)
using
the two
1/2”Plate.
ArmLine
Bolts
Stand)
usingbottom
the two
1/2"and
Arminsert
Boltsthe
and
twoBolts
of the
the
top
and
holes
Arm
andSmall
two Nuts.
of thePosition
Smallthe
Nuts.
Position
thethePointer
PointerArm
Armand
(with
curved
through
the
front
of the end
Pointer
Arm
Plate.
Arm
(with
the
curved
up,
facing
front)
end
up,the
facing
front)
against
theback
Arm of
Plate.
Line Bolts
up
Screw
Small
Nuts
onto
the
the
against
the
Arm
Plate.
Line
up the
topArm
and
botthe
top
and
bottom
holes
and
insert
the
Arm
Bolts
Wrench
and
1/8"
Allen
and
tighten
with
the
5/16"
tomthrough
holesthe
and
insert
the
ArmArm
Bolts
front
of the
Pointer
and through
Arm
Plate.the
Wrench.
The
Small
Nuts
can
be Arm
covered
with two
front
of
the
Pointer
Arm
and
Plate.
Screw End
the Small
Nuts onto the back of the ArmScrew
Bolts
Small
Caps.
theand
Small
Nuts
onto
the
back
of
the
Arm
Bolts
tighten with the 5/16" Wrench and 1/8" Allen
andWrench.
tightenThe
with
theNuts
5/16”
Small
canWrench
be coveredand
with1/8”
two
Allen
Wrench.
The
Small
Nuts
can
be
covered
Small End Caps.
with two Small End Caps.
STAND
LEGS
EXTENSION
LEGS
POINTER ARM
SMALL ENDCAPS (2)
POINTER ARM
SMALL ENDCAPS (2)
SMALL NUTS (2)
1/2" ARM BOLTS
ARM PLATE
1/2" ARM
BOLTS
SUPPORT
ARM
SMALL NUTS (2)
ARM PLATE
SUPPORT ARM
CROSSBAR
CROSSBAR
RUBBER FEET
RUBBER FEET
STAND LEGS
STAND LEGS
Assembly Instructions (cont.)
THE WHEEL, POINTER AND GRAPHICS
(1) Unpack the Wheel, remove any cardboard
and insert the 3-1/2” Wheel Bolt all the way
through the center of the front.
(2) Slide the two 1/2” Wheel Spacers onto the
Wheel Bolt and mount the Wheel on the Stand
by inserting the Wheel Bolt through both holes
of the Crossbar. Secure the Wheel Bolt with
the Wheel Washer and 5/16” Wheel Nut and
tighten with the 1/2” Wrench and 3/16” Allen
Wrench. The Wheel should spin smoothly.
(3) Attach the Pointer between the slots of
the Pointer Arm by lining up the holes and
securing with the two 3/8” Pointer Bolts and
two Small Nuts. Tighten with the 1/8” Allen
Wrench and the 5/16” Wrench. The Small
Nuts can be covered with the Small End Caps.
WHEEL NUT
WHEEL
SPACERS
WHEEL
WHEEL
WASHER
WHEEL BOLT
SMALL ENDCAPS (2)
(4) Attach the Magnetic Center Cover to the
front end of the Wheel Bolt.
(5) Insert Prize Pieces into the wheel slots.
SMALL NUTS (2)
POINTER
MAGNETIC
CENTER COVER
3/8" POINTER BOLTS (2)
WHEEL
TEETH
(6) Start spinning!
Storage Instructions
Store all parts in carry case (O) and place in a cool dry environment.
Care Instructions
Clean hardware with a damp cloth and wipe dry. Clean graphics with dry cloth.
Warranty Information
All products are designed to provide the user with a cost-effective and durable product. Standard warranty is a ‘one year parts and labor’
warranty which warrants product against defects in material and workmanship. It does not cover damage due to accidents, abuse, or normal
wear and tear. Products found to be defective will be replaced or repaired at factory’s discretion.