Crown CDi Amplifier Set-Up
For Origin Landscape Speakers
Models:
CDi1000
CDi2000
CDi4000
844·674·4461
[email protected]
LANDSCAPE CROWN AMPLIFIER INSTALLATION MANUAL
Table of Contents
Introduction
Crown Amplifier Ins & Outs
Input Connections
Unbalanced (Most Common)
Balanced
Output Connections
Terminating the Wires How to Load a Preset 2
2
2
2
3
4
4
8
How Many Speakers Can Be Run On Each Channel? 8
Technical Assistance
9
WWW.ORIGINACOUSTICS.COM
1
Introduction
This manual will specifically cover setup with the Crown CDi amplifier that our Origin Landscape speakers are designed to work
with.
For more detailed information about the Crown CDi amplifier,
refer to the Crown Operation Manual.
For useful information about the relative merits of different wiring
plans you may want to refer to the speaker installation manual
(available on-line).
Crown Amplifier Ins & Outs
Input Connections
Unbalanced (Most Common)
Connect your audio source to the Crown using the supplied cables
with RCA connectors on the source end Phoenix style connectors
on the Crown amplifier end. The Crown amplifier input channels
labeled CH1 and CH2. Both are identical.
2
844·674·4461
[email protected]
LANDSCAPE CROWN AMPLIFIER INSTALLATION MANUAL
Balanced
When using the Origin Landscape series in a commercial installation it might be necessary to connect the amplifier using balanced wiring. Connect the wires from your source equipment to
the Phoenix connector. Be sure to observe proper polarity when
connecting the wires to the Phoenix connector. If your source
equipment uses XLR connectors please confirm the polarity or
pin out of your source equipment before terminating the Phoenix
connector. See figure 1
CH. 1 Source
CH. 2 Source
Figure 1: Balanced Lines to the Phoenix connectors
NOTE
WHEN USING BALANCED INPUTS PLEASE CONSULT THE CROWN® AMPLIFIER MANUAL FOR GREATER DETAIL.
Shield
WWW.ORIGINACOUSTICS.COM
3
Output Connections
Terminating the Wires
Attach the supplied spade connectors to the ends of your speaker
cables. Then attach them to the output screws on the amplifier
and replace the supplied plastic cover to prevent a short circuit
or shock hazard.
CAUTION
CH1
CH2
- + + -
The amplifier should not be connected to AC power until all connections
are completed. High power 70v amplifiers present a serious shock hazard.
Do not connect speaker wires to the amplifier until all other connections
are completed.
Shield
4
844·674·4461
[email protected]
LANDSCAPE CROWN AMPLIFIER INSTALLATION MANUAL
WHICH PRESET TO USE?
The Crown CDi series amplifier you purchased from Origin Acoustics is preloaded with 20 presets to allow allow you to optimally
configure your sound system for practically any circumstance.
The presets have been divided into two families -- the Active
Crossover family and the Passive Crossover family.
The Active Crossover family is recommended for most installs. It
will have the subwoofers on one wire run (must be channel 1) and
the satellite speakers on the other (must be channel 2). The active
crossover removes the bass from the satellites, more effectively
controls how the subwoofer interfaces with the satellites and allows the custom DSP (digital signal processing) to be fed only to
the speakers they were designed for.
•Preset 2 is designed to make the LS 64 sound full range when
no subwoofer is to be used.
•Presets 7-11 require 2 or more amplifiers. They are intended
for larger installs and also give you greater control over the
balance between the subwoofer and the satellites. Presets
12-14 are for 8Ω installs and must use the 8” subwoofer and
satellites switched to 8Ω mode.
Channel 1
Channel 2
Amplifier
WWW.ORIGINACOUSTICS.COM
5
The Passive Crossover family, which is the approach you may be
most familiar with, allows satellites and subwoofers to be on a
single wire run.
•Presets 19 & 20 use the amplifier in bridged mode if only one
channel is available. This is anticipated to be used when wire
is pre-existing from a previous install.
Channel 1
Channel 2
Amplifier
6
844·674·4461
[email protected]
LANDSCAPE CROWN AMPLIFIER INSTALLATION MANUAL
Use this Satellite
Use this Sub
Preset #
Preset name
EQ Presets on Crown CDi Amplifiers for Origin Acoustics
Implications & Recommendations
When Sats and Subs on separate, designated wire runs (#2-8: Subs Ch1; Sats Ch2)
1
DSP OFF
No EQ or active crossover
2
AX0-64
0
64
No Sub
3
AX8-44
8
44
4
AX8-64
8
64
5
AX10-44
10 or 12 44
Subwoofers on one run & Satellites on
another run. Subwoofers crossed over to
Satellites
6
AX10-64
10 or 12 64
7
AX-44
0
44
LS44 satellites only. Subs to use second amp
8
AX-64
0
64
LS64 satellites only. Subs to use second amp
9
AX-8
8
Any 8” sub only. Satellites to use second amp
10 AX10
10
Any 10” sub only. Satellites to use second amp
11 AX12
12
Any 12” sub only. Satellites to use second amp
12 AX8-8ohm
8
Any Switch 8” sub to 8Ω. Satellites to use
second amp
13 AX44-8ohm 8
44
Switch LS44s sub to 8Ω. 8” subs to use
second amp
14 AX64-8ohm 8
64
Switch LS64s sub to 8Ω. 8” subs to use
second amp
When Sats & Subs are on the same wire runs
15 PX44-8
8
44
Uses passive crossover in 8” sub
16 PX64-8
8
64
17 PX44-10/12
10 or 12 44
18 PX64-10/12
10 or 12 64
19 Br44-8
8
44
Bridged amp. Designed for 8” sub and LS44
Satellites. Uses passive crossover in 8” sub
20 Br64-10
10 or 12 64
Bridged amp. Designed for 10” & 12” sub
and LS64 Satellites. Uses passive crossover in sub
Uses passive crossover in 10” or 12” sub. 12”
subs will result in 2dB more bass output
WWW.ORIGINACOUSTICS.COM
7
How to Load a Preset
1.Press the Select / Enter button on the front of the amplifier.
2.Press the Next / Down button until the word PRESET appears
on the display.
3.Press the Select / Enter button
4.Press the Next / Down or Prev / Up buttons until the preset
you desire is displayed
5.Press the Select / Enter button
6.Your chosen preset should now be displayed
HOW MANY SPEAKERS CAN BE
RUN ON EACH CHANNEL?
Origin Landscape speakers use an adjustable 70 volt transformer
that not only let you to set speaker’s volume level relative to the
other speakers in the system, but also allows you to increase the
number of speakers that can be run on each channel. The chart
below shows the maximum number of speakers you can use before the load becomes unsafe for the Crown CDi amplifiers (2Ω
load). If you’re using the amplifier in bridged mode you’ll need to
divide the maximum speaker number in half.
LS64
Setting Max
8 ohm 4
50W
36
25W
50
12W
100
6W
200
8
LS44
OSUB8
OSUB10 OSUB12
Setting Max Setting Max Max
Max
8 ohm 4
8ohm 2
30W
60 70V
14 8
8
15W
100
7W
200
4W
400
844·674·4461
[email protected]
LANDSCAPE CROWN AMPLIFIER INSTALLATION MANUAL
Technical Assistance
If you have any questions or concerns about installing or using
this product, you can reach us through one of the following methods:
Phone: (844) 674-4461
Hours of operation: 8:00am - 5:00pm (Pacific Time), Mon - Fri
Email: [email protected]
If you are having technical trouble, please include the model number and briefly explain what steps you took to resolve the problem
in your email, or be prepared to answer these questions over the
phone. If you are considering returning the product, it’s required
that you contact Origin Acoustics prior to any return attempts.
This way we can determine if the issue can be resolved without
returning the product, or if needed we can provide instructions
and support for the return process.
WWW.ORIGINACOUSTICS.COM
©2014 Origin Acoustics. All copyrighted, trademarked and
patented elements mentioned herein are the sole property of
Origin Acoustics.