WO1602F
Character 16x2 dots
72.1(B\L)
69.5(LCD)
61.0(VA)
56.2(AA)
9.4
6.3
2.7±0.2
(LCD)
7.7
3.55
2.95
0.60
0.55
K
6.8±1.0
1.0
0.7
P1.0*19=19.0
21.0±1.0
20
CONDUCTOR SIDE STIFEENER
STIFEENER
CONDUCTOR SIDE
0.3±0.15
0.3±0.15
4.6±1.0
(18.5)
1
"PROTECT TAPE"
5.95
5.55
0.70
0.65
"PROTECT TAPE"
13.0
1.0±0.3
(P1.0*13)
15.0±1.0
Contact Side
SCALE 2/1
ST7032
(3.1)
2-Ø1.5
ST7032i
W=0.7±0.1
2.7±0.2
(LCD)
2.0
ST7032i
50.0±1.0
29.6(B\L)
27.4(LCD)
(22.04)
17.5
15.1(VA)
11.5(AA)
10.0Max
A
(29.82)
DOT SIZE
SCALE 5/1
5.4
1.1
2.3
4.1
3.8
1.1
4.1
5.4
4.6±1.0
5.95
5.55
0.70
0.65
6.8±1.0
3.55
2.95
0.60
0.55
LED B/L
NO B/L
DOT SIZE
SCALE 5/1
1. Built-in controller (ST7032)
2. 1/16 duty ,1/5 bias
3. +5V power supply
Pin No.
Symbol
1
RS
2
R/W
3
E
4
DB0
Description
Select registers.
0: Instruction register (for write)
Busy flag & address counter (for read)
1: Data register (for write and read)
Select read or write (In parallel mode).
0: Write
1: Read
Starts data read/write. (“E” must connect to “VDD”
when serial interface is selected.)
Data bus line
5
DB1
Data bus line
6
7
DB2
Data bus line
DB3
Data bus line
8
DB4
Data bus line
DB5
Data bus line
9
10
11
12
VDD
14
Vout
PSB
15
16
PSI2B
Supply Voltage for logic
Operating voltage for LCD
Interface selection
0:serial mode
(“E” must connect to “VDD” when serial mode is
selected.)
1:parallel mode(4/8 bit)
In I2C interface PSB must connect to VDD
PSB
0
0
1
1
PSB
0
1
0
1
17
CAP1P
18
CAP1N
19
NC
No connection
20
NC
No connection
Item
Symbol
Power Supply VDD-VSS
VI
Input Voltage
Note: VSS=0 Volt , VDD=5.0 Volt .
DB6/SCL Data bus line
(In I2C interface DB6 (SCL) is clock input.
SDA and SCL must connect to I2C bus (I2C bus is to
connect a resister between SDA/SCL and the power of
I2C bus ).
DB7/SDA Data bus line
(In I2C interface DB7 (SDA) is input data.
SDA and SCL must connect to I2C bus (I2C bus is to
connect a resister between SDA/SCL and the power of
I2C bus ).
Ground
VSS
13
Item
Module Dimension
Viewing Area
Mounting hote
Dot Size
lnterface
No use
S14
2
S12(1 C)
Parallel 68
Item
Input Voltage
Supply Current
Recommended LC Driving
Voltage for Normal Temp.
Version module
LED Forward Voltage
LED Forward Current
Standard Value
72.1x29.6x9.4
61.0x15.1
65.1x22.6
2.95x5.55
Standard Value
max.
typ.
min.
--6.0
-0.3
-------
Symbol Condition
VDD
IDD
VDD=5V
-20ºC
0ºC
25ºC
VDD-VO
50ºC
70ºC
25ºC
VF
25ºC
IF
Unit
mm
mm
mm
mm
Character
type
Unit
V
V
Standard Value
max. Unit
min. typ.
5.25 V
5.0
4.75
0.5
1.0 mA
0.7
------------4.84.1
4.5
V
------------3.4
3.5
3.6
V
--V
16
---
For voltage booster circuit(VDD-VSS)
External capacitor about 0.1u~4.7uf
34