VID-TRANS70
2.4GHz WIRELESS AUDIO/VIDEO
TRANSMISSION SYSTEM
WITH TV TUNER
MANUAL
E N G L I S H
IMPORTANT-SAFETY PRECAUTIONS
This device of which operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
To prevent fire or shock hazard, do not expose this device to rain or moisture.
• Do not use near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or
near a swimming pool.
• To avoid electrical shock, do not open this device.
• This device should be operated to use only the power supply included with it or provided
as an accessory.
• Do not overload wall outlets and extension cords as this can result in the risk of fire or
electrical shock.
• Do not attempt to service this device yourself. Refer servicing to qualified personnel only.
Caution:
Changes or modifications not expressly approved by the Party responsible for
compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules, or BZT and CE EMC directive. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy, if not
installed and used in accordance with the instruction, it may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
1
A. PACKAGE CONTENTS
1. Transmitter
x1
2. Receiver
x1
3. Remote control
x1
(batteries not included)
4. Power adapter
!
x2
(230VAC to 9VDC)
DC in Jack
9V
600mA (Transmitter) /400mA (Receiver)
5. Audio/Video cable
x2
RCA to SCART connector
6. TV hook- up cable
x1
IEC 169-2(m) to IEC 169-2(f)
F-(m) to F-(m)
7. IR extender
x1
8. TV antenna splitter
x1
2
B. INTRODUCTION
The VID-TRANS70 is a wireless transmitter and receiver, using advanced wireless
communication technology to deliver audio and video up to 100 meters open area and 30
meters trough walls or floors. It transmit audio and video signals to a TV or VCR, without
additional coaxial cables.
The transmitter is equipped with a TV tuner and can be connected directly to the antenna
wall socket. The tuner can be programmed in a desired order of rank.
The transmitter converts the antenna signal into an audio/video signal. This signal will be
transmitted by the unit on a 2.4GHz frequency. The transmitter can be contolled with the
supplied remote control. The receiver is connected to the SCART of a TV or VCR.
It also integrates an UHF remote control extender to control the audio/video source using
the existing remote controller.
General remarks
1. The 2.4GHz antenna of the transmitter and receiver are directional and must be aimed in
an imaginary line for optimal performance.
2. Always use the system with the 2.4GHz antennas in open position for ventilation of the
electronic circuits.
3. The quality of the signal depends on the circumstances of the environment where the
system is located.
4. In case of possible distortion, the quality will increase when the system is re-located.
The quality can already increase with re-locating the system a few centimeters.
5. A microwave oven operates also on 2.4GHz, so it’s possible to have temporary distortion
when using this kind of equipment.
6. For optimal performance of the IR extender it’s necessary to install the infrared sensors
precisly on the infrared sensor of the connected equipment.
3
C. DESCRIPTION SYSTEM
1. ANTENNA For transmitting and receiving of the 433MHz signals from the remote control
of the connected equipment.
2. CHANNEL SWITCH Button to change the channels. The LED indicator (see 6) shows
the choosen channel.
3. 2.4GHz ANTENNA Directional antenna for receiving and transmitting.
4. IR JACK For connecting of the IR extender. (only transmitter)
5. INFRARED SENSOR For receiving of the remote controls signals of the connected
equipment.
6. LED INDICATOR Shows the choosen channel. (see also 2)
7. CH- Button for channel down. (only transmitter)
8. CH+ Button for channel up. (only transmitter)
9. CABLE/AV CABLE for TV tuner. AV for connected equipment.
Figure 1
3
1
2
9
8
7
4
6
5
4
REAR VIEW TRANSMITTER
1. AUDIO OUT Left (white) and right (red) channel output.
2. VIDEO OUT Video (yellow) output.
3. ANTENNA Connection for coaxial cable.
4. AUDIO IN Left (white) and right (red) channel input.
5. VIDEO IN Video (yellow) input.
6. DC JACK For connection of the power adapter.
7. OFF/ON SWITCH Switch for power off or on.
Figure 2
1
7
2
6
3
4
REAR VIEW RECEIVER
5
1. AUDIO OUT Left (white) and right (red) channel output.
2. VIDEO OUT Video (yellow) output.
3. DC JACK For connection of the power adapter.
4. OFF/ON SWITCH Switch for power off or on.
Figure 3
4
1
2
5
3
D. INSTALLATION
TRANSMITTER
1. Connect the coaxial cable to the antenna input and the antenna wall socket.
Option: (see figure 4)
2. Connect the TV splitter to the antenna input. Connect a coaxial cable to the antenna
input and the antenna wall socket. Connect another coaxial cable to the regular TV.
(extra coaxial cable not included)
3. Connect the RCA plugs of the audio/video cable to the audio/video output. Connect the
SCART plug to a TV or video. (choose AV status on equipment for picture)
Option: (see figure 5)
4. Connect the RCA plugs of the audio/video cable (this cable is not included) of a DVD or
other component to the audio/video input.
5. Connect the plug of the IR extender cable to the IR jack. Place the infra red sensors of
the IR cable on the infra red sensors.
6. Open up the 2.4GHz antenna and aim in a imaginary line to where the receiver is
located.
7. Connect the power adapter to the DC JACK and a wall socket.
8. Switch the transmitter on with the on/off switch.
9. Choose a channel (1,2,3 or 4).
10.Push CABLE/AV button for TV tuner or separate equipment.
Figure 4
Figure 5
6
RECEIVER
1. Connect the RCA plugs of the audio/video cable to the audio/video output.
Connect the SCART plug to a TV or video.
2. Open up the 2.4GHz antenna and aim in a imaginary line to where the transmitter is
located.
3. Connect the power adapter to the DC JACK and a wall socket.
4. Switch the transmitter on with the on/off switch.
5. Choose a channel (1,2,3 or 4). Note: choose same channel as choosen on the transmitter.
E. DESCRIPTION REMOTE CONTROL
0-9
Channel selection
CH+
Next Channel
CH-
Previous Channel
PREW.CH
Return to previous selected channel
TV/AV
TV for internal tuner / AV function for connected equipment
OK
Confirm function
DEL
Delete channel
SOURCE
OBJECT
}
Exchange channel, see paragraph channel set up
FINE+
Frequency increase (fine Tuning)
FINE-
Frequency decrease (fine Tuning)
-/--
Select channel above 9
SCAN
Automatic search for channels
7
F. CHANNEL SET UP
Automatic Channel Search
By using the automatic search method, all TV channels which are available on the cable
network will be stored in random order. In some areas it’s possible that the + and – channels
will be skipped. In this case these channels can be added with the fine tuning function.
Automatic search:
1. Turn the VID-TRANS70 on and a blue screen appears on the AV channel of the TV. Push
TV/AV button on the remote control for TV function. “TV” will appear in the blue screen.
For AV use push again and “AV” will apear in the blue screen.
2. Push SCAN on the remote control to start the scanning proces. “CHANNEL
SCANNING” appears and can take a few minutes. This proces will stop automatically and
the first found channel will be shown.
3. Push CH+ on the remote control to run through the channels to see what the found
channels.
Note: It’s possible that the system will show a blue screen for the channels which
are found but not strong enough to show. See DELETE CHANNELS for deleting
of these channels.
4. The channels which are so called + and – channels can be tuned with the FINE + and –
buttons on the remote control.
Delete channels:
1.
2.
3.
4.
Choose the channel which should be deleted.
Push the DEL button on the remote control.
“PRESS OK DEL” appears and push OK.
This channel is now delleted and will not be shown anymore.
Manual channel change:
This function gives the possiblity to program the found channels in a desired order.
1. Choose the channel which should be moved to another channel position.
2. Push the SOURCE button on the remote control and “SOURCE” appears.
3. Choose the new channel position.
4. Push the OBJECT button on the remote control and “PRESS OK EXC” appears.
5. Push the OK button and the channels will be changed.
Repeat these steps till every channel is in the desired position.
8
G. PERFORMANCE
For optimal performance it can be necessary to change the position of the transmitter and
receiver. In some cases a few centimeters will do. Objects which are between the imaginary
line of the transmitter and receiver can decrease the quality. If possible try to avoid these
objects. Also aim the antennas of the transmitter and receiver to each other in a imaginary line
to get the best picture quality.
Figure 6
H. USING THE IR EXTENDER
The IR extender makes it possible to control the connected equipment located on an other
position.
1. Connect the IR extender cable to the transmitter.
2. Place the IR sensors of the cable on the display of the connected component.
Note: Placing the sensor in front of the sensor from the component will increase
the functionality.
3. Aim the excisiting remote control at the receiver, located somewhere else, and the receiver
will send the signal to the transmitter which gives the signal to the connected component.
I. TROUBLESHOOTING
In case of any problems, please check all connections and read this manual again step by step
to avoid or solve any possible problem. Consult the dealer or an experienced technician for
help.
9
J. SPECIFICATIONS
Transmitter:
Operating Frequency Band
Output Level
Modulation
Channel
Video Input Level
Audio Input Level
Input Port
Antenna
IR–remote IR output
Infrared emission carrier
TV cable tuner
Standard
Memory
Power consumption
Dimension
Weight
2.400GHz~2.4835GHz (4 channels)
90 dBmV/m at 3 meters
FM (video and audio)
PLL frequency synthesizer (4 CH)
1V p-p 75 ohm
1V p-p 600 ohm (Stereo)
A/V jack-RCA line jack
Directional flat antenna
940nm with ON/OFF keying
38KHz
VHF low, VHF high, UHF
PAL
128 Channels
12VDC, 600mA
18cm x 12cm x 5cm
500g
Receiver:
Operating Frequency Band
Noise Figure
Channel
Video Output Level
Audio Output Level
Output Port
Antenna
Transmit Frequency
Infrared freq. Input
RF Output Channel
Power consumption
Dimension
Weight
2.400GHz~2.4835GHz (4 channels)
3.5dB
PLL frequency synthesizer (4 CH)
1V p-p 75 ohm
1V p-p 600 ohm (Stereo)
A/V jack-RCA line jack
Directional flat antenna
433.92 MHz or 418 MHz
35KHz~41KHz
CH36
12 VDC, 400mA
18cm x 12cm x 5cm
410g
System:
Operational range
In open area 100 meter, Closed area 30 meter
Remote control range
up to 50 meter (line of sight)
Actual operation range are subject to the circumstances of the environment
• Specifications subject to change without prior notice.
10
GENERAL INFORMATION:
MANUFACTURER/IMPORTER
Nedis B.V.
De Tweeling 28
5215MC ‘s-Hertogenbosch
The Netherlands
Tel.: 0031 73 5991055
Fax.: 0031 73 5999699
Email: [email protected]
WWW: www.nedis.com
This product has been designed, tested and manufactured according to the
European R&TTE Directive 1999/5/EC.
Conform this regulation it’s allowed to sell and use this product in following countries:
The Netherlands, Germany, France, Belgium, Italy, Austria, Sweden, Norway, Finland.
Nedis B.V. is not responsible for import and use in European countries which are not
mentioned above. It’s the responsibility of the importer.
0336 !
R&TTE Directive 1999/5/EC
AT
ES
IRE
SE
BE
FI
LU
UK
CH
FR
NL
11
DE
GR
NO
DK
IT
PT
ET91R-10-076-01,02,04 & LD911101L05
(report No.)
DECLARATION OF CONFORMITY
We, Nedis B.V.
(manufacturer’s name)
De Tweeling 28, 5215MC, ‘s-Hertogenbosch, The Netherlands
(manufacturer’s address)
Declare under our responsibility that the radio product:
HQ
(name)
VID-TRANS70
(type or model)
2.4Ghz Transmission / Reception System
(product description)
to which this declaration relates is in confirmity with the following standards:
Radio: EN300-1/-3:2000, EN300 440-2:2001
EMC: EN 301 489-1/-3:2000
Safety: EN 60065:1998
(title, number and date of issue of the standards)
following the provisions of 1999/5/EC (R&TTE Directive).
‘s-Hertogenbosch, 14-12-2003
(place and date)
12
Mrs. J. Gilad
General Purchase Director
(name, function, signature)