TM
Brief Product Descriptions
Imperial Oil
Downstream and Chemical
237 Fourth Avenue SW, Calgary, Alberta T2P 3M9
2015 Edition – Canada
For more information: 1- 888-968-3776
Brief Product Descriptions
mobil.ca
mobildelvac.ca
mobilindustrial.com
All trademarks used herein are trademarks or
registered trademarks of Exxon Mobil Corporation
or one of its subsidiaries.
2015 Edition – Canada
TM
TM
TM
TM
TM
TM
TM
TM
TM
TM
Brief Product
Descriptions
2015 Edition
237 Fourth Avenue SW, Calgary, Alberta T2P 3M9
For additional information please call our Technical Support Centre at
1 888 968-3776 or visit mobil.ca
Due to ongoing product research and development, the information herein is subject
to change without notification. Please refer to our Product Data Sheets found at
mobil.ca/pds for the most current product information.
2
INTRODUCTION
This book is provided as a field reference to our core product offer
of lubricating oils, greases and coolants. The format is designed to
help you choose precisely the right product for each application.
The content is divided into six sections:
Industrial
Commercial Vehicle
Passenger Vehicle
Marine
Aviation
Grease
Within each section, products are divided into
application groups. An alphabetical list of applications
is provided up front and an alphabetical index of
products is located at the end. An appendix provides
additional information.
Typical Properties are typical of those obtained with
normal product tolerance and do not constitute a
specification. Variations that do not affect product
performance are to be expected during normal
manufacture and at different blending locations.
All products may NOT be available locally.
For additional information please call our Technical
Support Centre at 1 888 968-3776 or visit mobil.ca.
Due to continual product development, these contents
are subject to change without notification. Please refer
to our Product Data Sheets found at mobil.ca/pds for
the most current product information.
1
Visit mobil.ca /pds for the most current product information
The Ultimate
Lubrication Warranty
Imperial will repair or replace any piece of
your equipment damaged due to the failure
of our lubricant.
All our lubricants meet or exceed original equipment manufacturers’ standards.
We guarantee their performance when used in accordance with Imperial’s
recommendations, the equipment manufacturers’ performance specifications,
and under normal operating conditions.
This warranty is in addition to any and all original equipment manufacturers’
warranties and does not invalidate them.
Because we are 100% committed to you, we stand behind our lubricants 100%.
See next page for complete warranty terms and conditions.
For further information on the Imperial Ultimate Lubrication Warranty or any
Mobil lubricant call Imperial at 1 888 968-3776.
TM
TM
TM
TM
TM
TM
TM
TM
TM
All trademarks used herein are trademarks or registered trademarks of Exxon Mobil Corporation or one of its subsidiaries. Limitation of liability:
in no event shall Imperial Oil be liable for any incidental, indirect, special, exemplary, punitive or consequential damages, including loss of profits.
2
Pegasus
Pegasus
Pegasus
The Ultimate Lubrication Warranty
Terms and Conditions
What the Warranty Covers
What the Warranty Does Not Cover
Imperial provides this warranty to direct purchasers of Mobil™
lubricants, where such lubricants have been purchased from an
authorized vendor. This warranty covers the Mobil product and
critical equipment parts lubricated by that product directly damaged
by a defect or malfunction of the lubricant. Imperial warrants that its
lubricants are free from defects and that the lubricant you purchased
will protect your equipment parts from oil related failure for three years,
provided that:
This warranty excludes:
• Mobil lubricants used in mechanically deficient equipment,
where the deficiency results from, but is not limited to: a
previously existing condition, abnormal operation; negligence;
abuse; damage from casualty, shipment or accident; or
equipment modification done without written authorization
from the OEM.
• The equipment was in good operating condition at the time
the lubricant was installed;
• Mobil lubricants used in equipment where the OEM required
lubricant standards do not match those stated by Imperial,
without prior written approval from Imperial.
• The lubricant was selected and maintained in accordance with
specifications of the original equipment manufacturer (“OEM”),
and the written recommendations (which include product
packaging) provided by Imperial at the time of sale; and
• Mobil lubricants and/or equipment pieces that have been used
in conjunction with any other product or additive that has not
been authorized for use by Imperial.
• The equipment has been operated within the limits specified
by the OEM.
Be advised that if your equipment is covered by a manufacturer’s
warranty, you should follow the equipment’s oil life sensor and the
oil change interval recommended in your owner’s manual to avoid
a disruption in the manufacturer’s warranty. Follow your owner’s
manual if the equipment is operated in any of the following severe
services: racing or commercial applications including taxis, limousines,
etc.; frequent towing or hauling; extremely dusty or dirty conditions;
or under excessive idling conditions.
What the Period of Coverage Is
The Ultimate Lubrication Warranty is valid for three (3) years from
the date of purchase or installation, whichever comes first.
What We Will Do to Correct Problems
Imperial will replace any lubricant that is defective. In addition, Imperial
will repair any equipment damage directly caused by a defect or
malfunction of the lubricant, at no cost to you, provided that the lubricant
was selected and maintained in accordance with specifications of the
OEM and the written instructions (which includes product packaging)
provided by Imperial. These are your exclusive remedies for any claim
for defective lubricant.
3
• Failure of equipment due to non-lubricant related conditions,
such as normal wear.
How You Can Get Service
To file a claim under this warranty, you must:
1. Within 48 hours from discovery of the damage (and not later
than six (6) months from the date the damage occurred), call
1-888-968-3776 to communicate the issue, and initiate a claims
investigation. You may also contact your Imperial or local
Distributor representative.*
2. Provide proof of purchase and maintenance records showing
that the equipment was serviced at the intervals recommended
by the OEM.
3. Allow an Imperial representative to examine the equipment
to determine the extent of the damage and to confirm that
the lubricant was the cause.
4. Allow an Imperial representative to obtain an oil sample, if
available, from the engine for oil analysis at no cost to you to
assist in determining the cause of the equipment failure.
TABLE OF CONTENTS
Introduction........................................................................................................................ 1
Ultimate Lubrication Warranty.......................................................................................2-3
Health and Safety Precautions......................................................................................5-7
Sustainability..................................................................................................................... 8
Energy Efficiency............................................................................................................... 9
Application Index of Products................................................................................... 10-11
Mobil SHC™ General Recommendations..................................................................... 12
Brief Product Descriptions...................................................................................... 14-104
Appendices............................................................................................................. 105-109
Temperature Conversion Table................................................................................. 105-106
Viscosity Conversion Table.............................................................................................. 107
Viscosity - Temperature Chart......................................................................................... 108
SAE Viscosity Grades for Engine Oils............................................................................. 109
SAE J306 Viscosity Grades for Gear Oils....................................................................... 109
Classification of Greases by National Lubricating Grease Institute
(NLGI) Consistency Numbers.......................................................................................... 109
Understanding Oil Analysis...............................................................................................110
ANSI-AGMA Industrial Gear Lubricants 9005-D94.......................................................... 111
Alphabetical List of Products................................................................................. 112-116
Viscosity Classification Equivalents............................................................................117
QUESTIONS?
CALL OUR TECHNICAL SUPPORT CENTER AT
1 888 968-3776
mobilindustrial.com | mobildelvac.ca | mobil.ca
Visit mobil.ca /pds for the most current product information
4
HEALTH AND SAFETY PRECAUTIONS
Workplace Hazardous Materials
Information System (WHMIS)
The Workplace Hazardous Materials Information
System or WHMIS is designed to ensure that all
employers obtain the information they need to inform
and train their employees properly about hazardous
materials used in the workplace.
WHMIS was developed through extensive consultation
with industry and labour representatives and the
federal, provincial and territorial governments. The
goal of WHMIS is to reduce the incidence of illness
and injuries resulting from the use of hazardous
materials in the workplace. Through legislation, the
WHMIS consensus establishes uniform requirements
to ensure that the hazards of materials produced or
sold in, imported into or used within workplaces in
Canada are identified by suppliers and employers
using standard classification criteria.
WHMIS provides employers and workers with one
additional tool to improve their understanding of
hazardous materials.To make the best use of this tool,
suppliers and employers have certain responsibilities.
A ‘supplier’ is a manufacturer, processor or packager
of a controlled product or a person who, in the course
of business, imports or sells controlled products. A
‘controlled product’ is defined for WHMIS under the
federal Hazardous Product Act as any product, material
or substance specified by the regulations included in
any of the classes listed in Table 1 (see page 6). An
‘employer’ is, for the purposes of WHMIS, the user of a
controlled product in the workplace or the producer of
a controlled product as part of a workplace process.
Under occupational safety and health legislation,
employers are also required to provide their employees
with hazard information received from their suppliers
with respect to controlled products used or produced
in the workplace, by means of appropriate workplace
labels, by distributing MSDS and by providing worker
education on the safe use of hazardous materials.
WHMIS is designed to ensure that all employers
receive the information they need to educate and
train their employees properly in the use of hazardous
materials in the workplace. It will also provide
employees with necessary hazard information so they
can participate in, and support, the precautionary
measures instituted in their workplaces.
As a supplier of petrochemical products in Canada,
Imperial Oil has issued material safety data sheets
for all Imperial Oil products and prepared labels
that comply with WHMIS for all controlled products.
Controlled products can be easily identified because of
the special WHMIS supplier label. Material Safety Data
Sheets should be consulted prior to handling a product
to ascertain whether there are any specific health
and safety risks or special handling requirements
that should be addressed. Imperial Oil will continue
to investigate the potentially hazardous properties of
existing and new materials through extensive testing
and research programs.
Suppliers must convey hazard information to
purchasers in a specified manner by means of
labelling of the controlled products or containers of the
controlled products, and by providing more detailed
information concerning the controlled product in the
form of a Material Safety Data Sheet (MSDS).
5
Visit mobil.ca /pds for the most current product information
HEALTH AND SAFETY PRECAUTIONS
Material Safety Data Sheets
Product Handling
What kind of information does an MSDS provide?
Most lubricating oils and greases are not controlled
under WHMIS legislation in Canada. However, certain
basic handling procedures should be observed to
keep the petroleum products off the skin and to avoid
inhalation of their vapours and mists. The following
guidelines apply to the handling of all petroleum
products and in general to other chemicals with which
you may come in contact.
An MSDS typically contains the following types of
information:
• Physical data on the product (e.g. viscosity,
flash point)
• The nature and degree of health, environmental
and safety hazards associated with the product
• Precautionary guidelines for proper and safe
handling of the product in order to avoid fire,
explosion and acute and chronic health hazards
• Emergency procedures in the event of fire, spill
or excessive exposure to the product by skin
contact, ingestion or inhalation
Imperial Oil customers in Canada can obtain
Material Safety Data Sheets (MSDS) and Workplace
Hazardous Materials Information System (WHMIS)
information, in English or French, for all products.
Through the customer-establishment process,
customers of WHMIS-controlled products will receive
a Material Safety Data Sheet (MSDS) on or before
first shipment of the controlled product. Subsequent
updates to that sheet are directed to the identified
customer contact.
Always remember to:
• Minimize skin contact with whatever product you
are using.
• Remove oils from the skin promptly, using mild nonabrasive soap and warm water or a skin cleanser
and warm water.
• Do not use gasoline, solvents, kerosene or similar
products to remove oil or grease from the skin.
• Do not wear oil-soaked clothing. Launder all
work clothes frequently. Put oily rags in the correct
container. Discard oil-soaked shoes and belts.
• Wash hands and face thoroughly before eating and
at the end of a shift. Take a shower if possible before
leaving work.
• Clean up spilled product promptly and dispose of it
correctly. Keep product out of sewers and waterways.
MSDS are also available through any of the
following options:
• Get first aid for all cuts and scrapes and report
as required.
• Visit our website at www.imperialoil.ca/msds.
• Avoid inhalation of oil mist and solvent vapours.
• Use our automated ‘FAX-BACK’ system:
call 1-800-IOL-MSDS or 1-800-465-6737.
Please have your fax number available.
• Obtain medical advice on all potential health-hazard
problems.
• Call 1-888-968-3776 to speak to a customer
service representative.
One of the least recognized, yet most serious,
workplace hazards is a punctured oil line under
pressure. When a jet of pressurized fluid makes contact
with the skin, it can enter the body and cause serious
injury. That is why, under absolutely NO circumstances,
should you try to stop a hydraulic oil leak with your
finger. Always be aware of the risk when you’re working
near hydraulic equipment and if your skin is struck by
pressurized fluid, seek medical attention immediately.
• Contact your Imperial sales representative
In addition, our technical sales representatives can
assist in providing information on the safe storage
and use of Imperial Oil products. Special customer
requests will be directed to our industrial hygiene/
product safety department.
Visit mobil.ca /pds for the most current product information
6
HEALTH AND SAFETY PRECAUTIONS
Table 1 – WHMIS Class and Division Hazard Symbols
CLASS AND DIVISION DESIGNATION
SYMBOL
CLASS A – Compressed Gas
CLASS B – Flammable and Combustible Material
Flammable Gas
Flammable Liquid
Combustible Liquid
Flammable Solid
Flammable Aerosol
Reactive Flammable Material
CLASS C – Oxidizing Material
CLASS D – Poisonous and Infectious Material
1. M
aterial causing immediate and
serious toxic effect
2. Material causing other toxic effects
3. Biohazardous infectious material
CLASS E – Corrosive Material
CLASS F – Dangerously Reactive Material
7
Visit mobil.ca /pds for the most current product information
SUSTAINABILITY
The three pillars of Advancing Productivity serve as part of our corporate commitment to sustainability. At
ExxonMobil, “sustainability” means balancing economic growth, social development and environmental
protection so that future generations are not compromised by actions taken today.
To put sustainability in motion, we take a holistic approach across our offer, communication and process,
providing innovative lubricants and services that can create tangible value for you in the areas of safety,
environmental care and productivity. Through Advancing Productivity, our goal is to deliver performance
benefits in these three crucial areas of your business so that you can achieve your full vision of success.
*
Safety
Environmental Care
Productivity
Minimizing employee –
equipment interaction
Designed to help lighten
environmental touch
Controlling costly downtime
and delays
We offer products and services
that can help you mitigate potential
Our commitment to minimizing
environmental impact has led us
Enhancing the competitive potential
of our customers is an important
employee injury caused by direct
contact with equipment. These
to create technologically advanced
products and innovative services with
part of Advancing Productivity.
We achieve this objective through
products and services are designed
to help:
that goal in mind. We strive to help
you achieve this goal through:
lubrication solutions that can
help provide:
• Provide long drain intervals and
• Optimized oil drain intervals, which
enhance equipment reliability,
minimizing maintenance, repair
can help reduce used oil volume
and product packaging, as well as
• Long drain intervals, which can
help improve equipment availability,
and replacement
• Reduce the potential for leaks
service-related risks
• Long component life, to help reduce
that arise from handling used oil
and related products
• Increase employee safety
worn equipment disposal and
maintenance-related waste
• Potential GHG emissions reduction
awareness and knowledge of a
and other energy-efficiency benefits
lubricant’s effect on health
and safety
• Address the risk of potential
product misapplication
reduce lubricant transaction
frequency and minimize
disposal costs
• Powerful equipment protection,
which can maximize equipment
availability, helping you control
costs of equipment maintenance
and replacement
• Inventory consolidation potential
*Visit mobilindustrial.com to learn how certain Mobil-branded lubricants may provide benefits to help minimize environmental impact.
Actual benefits will depend upon product selected, operating conditions, and applications.
Visit mobil.ca /pds for the most current product information
8
ENERGY EFFICIENCY
About the Energy Efficiency Seal
As the supplier of Mobil™ Industrial Lubricants, we are
committed to providing products and services that help
deliver tangible performance and sustainability-related
benefits – as well as material economic advantages –
to Canadian industry and consumers.
Our extensive range of high performance lubricants
can help increase equipment operating efficiency
and engine fuel economy. These lubricants can also
contribute to reduced energy and resource use, lower
emissions, and cost savings for industrial equipment.
The Energy Efficiency Seal is the typographic representation for all Mobil Industrial Lubricants that meet
the rigorous criteria for outstanding energy efficiency.
These criteria are determined on a case-by-case basis
and are dependent on the product category and application. Statistically valid data must be available to substantiate the energy efficiency claim and demonstrate a
statistically significant decrease in energy consumption or
increase in efficiency when compared with commercially
available products designed for the same application.
Below are the Mobil Industrial Lubricants products in which this technology is available:
Mobil SHC™ 500
Mobil DTE 10 Excel™
Energy efficiency relates solely to the fluid performance when compared with Mobil DTE 10
Excel™ standard hydraulic fluids. The technology allows an increase in hydraulic pump
efficiency of up to 6 percent compared with Mobil DTE 20 Series when tested in standard
hydraulic applications. The energy efficiency claim for this product is based on test results
conducted in accordance with applicable industry standards and protocols.
Mobil SHC Pegasus™ The energy efficiency of Mobil SHC Pegasus relates solely to the fluid performance
when compared to standard Mobil SAE 40 natural gas engine oils. Mobil SHC Pegasus
technology demonstrated an increase in fuel efficiency of up to 1.5 percent, compared
to Mobil Pegasus 1005 and 805 series when tested in standard natural gas engine
applications under controlled conditions. Efficiency improvements will vary based on
operating conditions and applications. The energy efficiency claim for this product is
based on test results on the use of the fluid conducted in accordance with applicable
industry standards and protocols.
Mobil SHC™ Gear
Energy efficiency relates solely to the fluid performance when compared with conventional
reference (150-1000) oils of the same viscosity grade in gear applications. The technology
used allows an increase in fuel efficiency of up to 3.6 percent compared with the reference
oil when tested in a worm gearbox under controlled conditions. Efficiency improvements
will vary based on operating conditions and applications.
Mobil SHC™ 600
Mobil SHC Cibus™
Energy efficiency relates solely to the fluid performance when compared to conventional
(mineral) Mobil SHC Cibus™ reference oils of the same viscosity grade in circulating and
gear applications. The technology allows an increase in fuel efficiency of up to 3.6 percent
compared to the reference oil when tested in a worm gearbox under controlled conditions.
Efficiency improvements will vary based on operating conditions and application.
The above products provide energy efficiency benefits when compared with standard products of the
same category and application, helping our customers to operate their equipment more efficiently.
9
Visit mobil.ca /pds for the most current product information
APPLICATION INDEX OF PRODUCTS
INDUSTRIAL LUBRICANTS
Chain Oils.................................................................................................................... 18
Circulating Oils.......................................................................................................19-20
Compressor Oils..................................................................................................... 21-24
Cylinder Oils................................................................................................................25
Food Industry Lubricants........................................................................................26-27
Gas Engine Oils......................................................................................................28-32
Gear Oils – Enclosed Gears...................................................................................33-34
Gear Oils – Enclosed Gears Specialty...................................................................35-36
Gear Oils – Open Gears..............................................................................................36
Heat Transfer Fluids.....................................................................................................37
Hydraulic Fluids...................................................................................................... 37-40
Hydraulic Fluids – Less Flammable.............................................................................41
Metalworking Fluids................................................................................................42-43
Mist Oils.......................................................................................................................44
Other Industrial Oils................................................................................................45-46
Paper Machine Oils.....................................................................................................47
Pneumatic Tool Lubricant............................................................................................48
Quench Oils.................................................................................................................48
Refrigeration Oils.........................................................................................................49
Rust Preventive............................................................................................................50
Spindle Oils.................................................................................................................51
Transformer Oils..........................................................................................................51
Turbine Oils.............................................................................................................52-54
Way Oils......................................................................................................................55
COMMERCIAL VEHICLE LUBRICANTS
Heavy Duty Diesel Engine Oils...............................................................................60-62
Heavy Duty Natural Gas Engine Oils..........................................................................62
Heavy Duty Power Transmission Fluids............................................................63, 66-67
Tractor Hydraulic Fluids...............................................................................................68
Railway........................................................................................................................68
Coolant/Antifreeze ......................................................................................................69
Visit mobil.ca /pds for the most current product information
10
APPLICATION INDEX OF PRODUCTS
PASSENGER VEHICLE LUBRICANTS
Passenger Vehicle Engine Oils..................................................................................74-76
Passenger Vehicle Drive Train Fluids.........................................................................77-78
Motorcycle Oils ............................................................................................................. 78
Passenger Vehicle Installer Greases............................................................................. 78
MARINE LUBRICANTS
Crosshead Engine Oils.................................................................................................. 81
Trunk Piston Engine Oil................................................................................................. 82
Marine Hydraulic Oil...................................................................................................... 83
Marine Grease............................................................................................................... 83
AVIATION LUBRICANTS
Grease...................................................................................................................... 85-86
Jet Oil............................................................................................................................ 86
GREASES
Automotive..................................................................................................................... 91
Couplings....................................................................................................................... 92
Electric Motors............................................................................................................... 93
Environmentally Aware.................................................................................................. 93
Food Industry (NSF H-1)............................................................................................... 94
Gears – Enclosed, Semi-Fluid....................................................................................... 94
Gears – Open................................................................................................................ 95
High Temperature – Clay Thickened.............................................................................. 96
Marine........................................................................................................................... 96
Multi-Purpose............................................................................................................97-99
Off-Highway Heavy Duty Equipment and On-Highway Trucking...................................100
Paper Machines............................................................................................................ 101
Pneumatic Tools........................................................................................................... 101
Railway.........................................................................................................................102
Drilling..........................................................................................................................102
Specialty Synthetic.......................................................................................................103
Threads.................................................................................................................103-104
Wind Turbine.................................................................................................................104
Wire Ropes...................................................................................................................104
11
Visit mobil.ca /pds for the most current product information
MOBIL SHC GENERAL RECOMMENDATIONS
Productivity That’s Proven
What truly sets Mobil SHC™ synthetic lubricants apart from its competitors is its track record.
It represents Productivity That’s Proven – the underlying claim behind our brand. No other synthetic
lubricant has the experience, the proof, and the reputation to match it.
The full – and unmatched – suite of products that carry the Mobil SHC name have been tried,
tested and proven in almost every type of equipment, under almost every condition.
Mobil SHC General Recommendations:
Circulating Mobil SHC 600™ Series
Mobil Glygoyle™ Numbered Series
Compressors Mobil Rarus SHC™ 1020 Series (rotary screw and vane)
Mobil Rarus™ 800 Series (reciprocating)
Food Industry (NSF H-1) Mobil SHC Polyrex™ Grease Series
Gas Engine Mobil SHC Pegasus™ 30
Mobil Pegasus™ 1
Gear
Mobil SHC 600™ Series
Mobil SHC Gear™ Series
Mobilgear SHC™ XMP Series (wind turbines)
Hydraulics Mobil SHC™ 500 Series
Mobil EAL Envirosyn™ H Series
Paper Machine Mobil SHC™ PM Series
Mobilith SHC™ PM Grease Series
Turbine Mobil SHC™ 800 Series
Grease Mobilith SHC™ Series (multi-purpose)
Mobil SHC Polyrex™ Series (Food/NSF H-1, high temperature)
Mobil SHC™ PF 462 (extreme high temperature)
Mobil SHC™ Grease 460 WT (wind turbines)
Mobiltemp SHC™ 32 (high speed)
Mobil SHC™ Grease 100 EAL Series (environmentally aware)
Mobilith SHC™ PM Series (paper machine)
Visit mobil.ca /pds for the most current product information
12
QUESTIONS?
CALL OUR TECHNICAL SUPPORT CENTER AT
1 888 968-3776
mobilindustrial.com | mobildelvac.ca | mobil.ca
PAGE
Chain Oils
Circulating Oils
Compressor Oils
Cylinder Oils Millcot™ K.................................................................................18
Mobil™ Chainoil........................................................................18
Mobil™ Heavy Duty (HD) Chainoil............................................18
Food Industry Lubricants Mobil™ Food and Beverage Industry Selector........................ 26
Mobil SHC Cibus™ Series....................................................... 27
Mobil DTE™ FM Series........................................................... 27
Mobil SHC™ 600 Series...........................................................19
Mobil Glygoyle™ Numbered Series..........................................19
Mobil Vacuoline™ 500 Series...................................................19
Mobil DTE™ Oil Named Series............................................... 20
Mobil Teresstic™-C.................................................................. 20
Mobil Teresstic™ V 150............................................................ 20
Mobil Rarus SHC™ 1020 Series............................................. 21
Mobil Rarus™ 800 Series........................................................ 21
Mobil Rarus™ 427................................................................... 21
Exxcolub™ SCF PG................................................................ 22
Exxcolub™ SCF PS................................................................. 22
Exxcolub™ SCF M2................................................................. 22
Exxcolub™ Application Chart.................................................. 23
Mobil™ Compressor Oils......................................................... 24
Mobil™ Compressor Oils 264 and 460.................................... 24
Mobil™ Compressor Oil N 100................................................ 24
Mobil Teresstic™ AC 32........................................................... 24
Mobil™ Cylinder Oils............................................................... 25
Mobil DTE™ Oil 205................................................................ 25
MARINE
PASSENGER
PRODUCT
COMMERCIAL
OIL APPLICATION
INDUSTRIAL
INDUSTRIAL PRODUCT LISTING BY APPLICATION
AVIATION
14
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL PRODUCT LISTING BY APPLICATION
OIL APPLICATION
PRODUCT .
PAGE
Gas Engine Oils
Engine Oil Selection Chart...................................................... 28
Mobil SHC Pegasus™ 30........................................................ 29
Mobil Pegasus™ 1................................................................... 29
Mobil Pegasus™ GMA............................................................. 29
Mobil Pegasus™ 805............................................................... 29
Mobil Pegasus™ GLX.............................................................. 30
Mobil Pegasus™ 710............................................................... 30
Mobil Pegasus™ 610............................................................... 30
Mobil Pegasus™ 605............................................................... 31
Mobil Pegasus™ 801 Series.................................................... 31
Mobil Pegasus™ AGX.............................................................. 31
Engine Oil Selector.................................................................. 32
..........................................................................................
Gear Oils – Enclosed Gears
Mobil SHC Gear™ Series (ISO VG 150-1000)......................... 33
Mobil SHC Gear™ 1500, 3200, and 6800................................ 33
Mobilgear™ 600 XP Series...................................................... 34
SPARTAN™ EP-C.................................................................... 34
Gear Oils – Enclosed Gears Specialty
Gear Oils – Open Gears Heat Transfer Fluids Mobil SHC™ Gear OH Series.................................................. 35
Mobilgear SHC™ XMP Series................................................. 35
Mobil Glygoyle™ Series........................................................... 35
Mobil Iogear™ EP 100............................................................. 36
Mobil SHC Gear™ 46M........................................................... 36
Mobiltac™ 375 NC................................................................... 36
Mobil Geargard™ HVS............................................................. 36
Mobiltherm™ and Thermoil™.................................................. 37
15 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
PAGE
Mobil SHC™ 500 Series.......................................................... 37
Mobil DTE 10 Excel™ Series................................................... 37
Mobil DTE™ 20 Series............................................................. 38
Mobil Univis™ Ultra.................................................................. 38
Mobil Univis™ Extra................................................................. 38
Mobil Univis™ N-C Series........................................................ 39
Mobil Univis™ HVI 13.............................................................. 39
Mobil Univis™ BIO-C 40.......................................................... 39
Mobil Nuto™ H Series.............................................................. 40
Forum™ EP 46 and 68............................................................. 40
Hydraulic Fluids – Less Flammable
Mobil Nyvac™ FR 200D........................................................... 41
Mobil Pyrogard™ 53................................................................. 41
Metalworking Fluids
Mobilmet™ 420 Series............................................................. 42
Mobilmet™ 760 Series............................................................. 42
Mobilcut™ 100......................................................................... 42
Mobilcut™ 140......................................................................... 43
Mobilcut™ 350......................................................................... 43
Formesso™ Summer Grade.................................................... 43
Mist Oils
Mobilgear™ MS Series............................................................ 44
Click Here to return to PRODUCT APPLICATION INDEX
16
GREASES
Visit mobil.ca /pds for the most current product information
AVIATION
Other Industrial Oils
Canthus™ 680......................................................................... 45
Faxam™................................................................................... 45
Mobil™ Sawguide Oils............................................................. 45
Mobil™ Synthetic Oven Lube 1090.......................................... 46
Mobil Synturion™ 6.................................................................. 46
Mobil™ System Cleaner........................................................... 46
Slurry Oil 62............................................................................. 46
MARINE
Hydraulic Fluids
PASSENGER
PRODUCT
COMMERCIAL
OIL APPLICATION
INDUSTRIAL
INDUSTRIAL PRODUCT LISTING BY APPLICATION
INDUSTRIAL PRODUCT LISTING BY APPLICATION
OIL APPLICATION
PRODUCT
PAGE
Paper Machine Oils
Mobil SHC™ PM Series........................................................... 47
Mobil DTE™ PM Series........................................................... 47
Pneumatic Tool Oils Quench Oils
Mobil Arox™ EP Series............................................................ 48
Refrigeration Oils
Mobil Glygoyle™ 22................................................................. 49
Mobil Gargoyle™ Arctic Oils..................................................... 49
Mobil Gargoyle Arctic SHC™ 200 Series................................. 49
Mobil Zerice™ S Oils............................................................... 49
Rust Preventive
Mobilarma™ 245...................................................................... 50
Mobilarma™ 700 Series........................................................... 50
Mobil Vaprotec™ Light............................................................. 50
Spindle Oils
Mobil Velocite™ Oil Numbered Series..................................... 51
Mobil Fenso™ Series............................................................... 48
Transformer OilsVoltesso™................................................................................ 51
Turbine Oils
Mobil SHC™ 800 Series.......................................................... 52
Mobil DTE™ 932 GT................................................................ 52
Mobil DTE™ 800 Series........................................................... 52
Mobil DTE™ 724 Oil................................................................ 53
Mobil DTE™ 732 Oil................................................................ 53
Mobil DTE™ 700 Series........................................................... 53
Mobil Teresso™........................................................................ 54
Mobil Teresso™ GTC Series.................................................... 54
Way Oils
Mobil Vactra™ Oil Numbered Series........................................ 55
Mobil Vacuoline™ 1400 Series................................................. 55
17 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
CHAIN OILS
Millcot™ K. Tacky, anti-spattering, general purpose
oils, originally developed for textile machinery and
well suited for a wide range of thin film applications
in general manufacturing. Ideal for lumber industry
applications, such as chains and hand oiled bearings
Millcot K 68
Millcot K 100
Millcot K 220
68
100
220
20
30
50
Product
Mobil Chainoil Light
Mobil Chainoil Heavy
Pour Point,
°C, ASTM D97
Flash Point
°C, ASTM D92
65.4 105
209
8.1 11.1
17.3
-24
-12
-3
196
202
238
for moderate temperatures (-10°C to 30°C), Mobil
Chainoil Light for lower temperatures down to -30°C.
Also recommended for industrial chain drive and plain
bearing applications requiring a tacky anti-wear oil.
cSt at 40°C
Pour Point
°C, ASTM D97
Flash Point
°C, ASTM D92
40
150
-33
-20
180
190
anti-wear and extreme pressure additives help reduce
wear to guide bars, chains and sprockets. A specialized inhibitor minimizes rust and corrosion. A tackiness
additive helps reduce oil consumption due to throw-off.
Also recommended for industrial chain drive and plain
bearing applications requiring a tacky anti-wear oil.
Viscosity, ASTM D445
cSt at 40°C
Pour Point
°C, ASTM D97
Flash Point
°C, ASTM D92
220
-15
260
MARINE
Mobil Heavy Duty Chainoil
cSt at
100°C
Viscosity, ASTM D445
Mobil™ Heavy Duty (HD) Chainoil. This premium
chainsaw lubricant helps extend the life of chains and
guide bars on high speed chainsaws operating under
severe conditions. Recommended for spring through
fall operation across a temperature range of -5°C
to 40°C. High viscosity base stocks enhanced with
Product
cSt at
40°C
PASSENGER
Mobil™ Chainoil delivers excellent chain and bar
lubrication in residential and industrial chain saw
applications. A tacky stay-in-place film of oil lubricates,
cleans and cools moving parts, helping to extend bar
and chain life. Mobil Chainoil Heavy is recommended
Viscosity, ASTM D445
COMMERCIAL
Approximate
Product
ISO VG
SAE Grade
in sawmills and lead screws on plywood veneer
lathes. Millcot K oils are fortified with rust inhibitors
and anti-wear additives and can be applied using
most lubrication methods.
INDUSTRIAL
INDUSTRIAL LUBRICANTS
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
18
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
CIRCULATING OILS
Mobil SHC™ 600 Series. These exceptional performance synthetic gear and bearing oils help increase
productivity by delivering outstanding equipment protection, oil life and problem-free operation. The latest
proprietary and patent pending Mobil SHC technology
performs well beyond the capabilities of conventional
oils in demanding applications across a wide range
of temperatures. These products are resistant to
mechanical shear, even in heavily loaded gear and
high shear bearing applications, so that there is
virtually no loss of viscosity. Mobil SHC 600 Series
lubricants have excellent low temperature properties,
as well as improved air release performance in the
lower viscosity grades. For information on energy
efficiency, please see page 7.
Product
ISO VG
Viscosity, ASTM D445
FZG scuffing test,
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D5950
Flash Point,
°C, ASTM D92
DIN 51534 (mod),
A/16.6/90, Fail Stage
Mobil SHC 624 Mobil SHC 625 Mobil SHC 626 Mobil SHC 627 Mobil SHC 629 Mobil SHC 630 Mobil SHC 632 Mobil SHC 634 Mobil SHC 636 Mobil SHC 639 32
46 68 100 150 220 320 460 680 1000 6.3 8.5 11.6 15.3 21.1 28.5 38.5 50.7 69.0 98.8 148 161 165 162 166 169 172 174 181 184 -57 -54 -51 -45 -42 -42 -42 -39 -39 -33 236 225 225 235 220 220 225 228 225 222 11
12
12
12
13
13+
13+
13+
13+
13+
32 46 68 100 150 220 320 460 680 1000 Mobil Glygoyle™ Numbered Series oils are
polyalkylene glycol-based (PAG) high performance
lubricants that provide outstanding lubrication in
extreme temperature gear, bearing and circulation
system applications in conditions well beyond the
capabilities of mineral oils. They are shear-stable
Viscosity, ASTM D445Spec. Gravity
Product
Mobil Glygoyle 22 cSt at
40°C
cSt at
100°C
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
kg/l at 20°C,
ASTM D1298
177 25.1 -41 229 1.007
Mobil Vacuoline™ 500 Series are high performance
heavy duty circulating oils specifically designed to meet
the critical requirements of high speed No-Twist Rod
Mills manufactured by Morgan Construction Company
and Danieli. Their versatile performance makes them
an excellent choice for circulation systems of primary
and mini-mill bearings. These oils are formulated from
Product
ISO VG
Mobil Vacuoline 525 Mobil Vacuoline 537
and have outstanding resistance to thermal degradation,
oxidation and the formation of sludge and deposits.
They incorporate a proprietary additive package
designed to enhance EP/anti-wear protection, corrosion
and rust protection and foam resistance without detracting from the intrinsic attributes of the PAG base oils.
–
320 high quality base stocks and a proprietary additive
system to provide enhanced film strength, anti-wear
and anti-scuff properties. They enjoy strong support
from equipment builders, and their exceptional performance over many decades makes them the lubricant
of choice of many mill operators, worldwide.
Viscosity, ASTM D445 Spec. Gravity
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
kg/l at 15.6°C,
ASTM D1298
89 309 10.7 24.4
99 96 -24 -12 264 288 0.88
0.89
19 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
CIRCULATING OILS
to emulsification. They provide excellent protection
against rust and corrosion, including resistance to salt
water, and good anti-wear properties. These grades
have excellent air release properties, enabling
entrained air to separate, avoiding pump cavitation
and erratic operation.
Viscosity, ASTM D445
Product
ISO VG
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Mobil DTE Oil Light Mobil DTE Oil Heavy Medium Mobil DTE Oil Heavy 31.0 65.1 95.1 5.5 8.7 10.9 102 95 92 -18 -15 -15 218
223
237
32 68 100 ring oiled steam turbine bearings. All viscosity grades
are formulated with select high performance mineral
oil base stocks and carefully chosen additives to
provide long service life, outstanding oxidation control,
excellent rust and corrosion protection, rapid air release
and foam control.
Product
ISO VG
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Mobil Teresstic-C 100 Mobil Teresstic-C 150 Mobil Teresstic-C 220 Mobil Teresstic-C 320 100.0 150.0 220.0 320.0 11.3 14.6 18.4 23.7 99 96 92 94 -15
-12
-6
-6
99 96 92 94 Product
ISO VG
Mobil Teresstic V 150
150
Flash Point,
°C, ASTM D92
252
260
256
278
oxidation inhibitors help control corrosion and prolong
oil life. A potent anti-wear additive helps protect gears
and associated bearings.
MARINE
Mobil Teresstic™ V 150 circulating oil is recommended
for older paper machines with specific performance
requirements. A friction reducing additive is particularly
effective in dryer section journal bearings. Rust and
PASSENGER
Mobil Teresstic™-C. These oils are formulated for
long service life in circulating systems, hydraulic systems that do not require an anti-wear oil, heat transfer
systems, light duty gear cases, friction clutches and
other industrial units for which long, trouble-free service
is required. They are also used to lubricate bath and
COMMERCIAL
Mobil DTE™ Oil Named Series are premium performance circulating oils for applications requiring long
lubricant life, including steam and hydro turbine sets
and other systems. These oils are formulated from
highly refined base stocks and additives, which provide
extremely high levels of chemical and thermal stability,
rapid separation from water and high resistance
INDUSTRIAL
INDUSTRIAL LUBRICANTS
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
Pour Point,
°C, ASTM D97
150
14.6
-3
Flash Point,
°C, ASTM D92 256
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
20
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
COMPRESSOR OILS
Mobil Rarus SHC™ 1020 Series. These high
performance oils are primarily intended for severe
duty rotary screw and vane air compressors. They
are particularly well suited where mineral oil based
products are not meeting expectations, in applications
subjected to high final compression temperatures or
where extended oil drain intervals are desired. Designspecific wax-free synthetic fluids and high technology
Viscosity, ASTM D445
Product
ISO VG
Mobil Rarus SHC 1024 Mobil Rarus SHC 1025 Mobil Rarus SHC 1026 additives are formulated for exceptional resistance to
oxidation and thermal degradation. Their high viscosity
index delivers effective lubrication at high temperatures.
Mobil Rarus SHC 1020 Series oils help improve productivity and reduce maintenance costs by minimizing
downstream deposits and delivering outstanding
equipment protection and reliability.
32 46 68 cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
31.5 44 66.6 5.7 7.2 10.1 127 131 136 -48 max
-45 max
-45 max
245
246
246
Mobil Rarus™ 800 Series is a line of high performance air compressor lubricants primarily intended
for the lubrication of severe duty reciprocating air
compressors. They are engineered to meet or exceed
the stringent requirements of the major compressor
manufacturers. They are formulated with synthetic
ester base oils and a high technology additive system
that provides exceptional equipment protection
and reliability. Mobil Rarus 800 Series oils provide
excellent wear protection and outstanding resistance
to oxidation and thermal degradation. Their unique
formulation provides the ability to help reduce maintenance costs through minimizing equipment problems
and downstream deposits and carryover.
Product
ISO VG
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Mobil Rarus 824 Mobil Rarus 827 Mobil Rarus 829 29.5 107.5 158 5.5 10.12 13.2 127 66 70 -54 -36 -40 244
270
270
32 100 150 Mobil Rarus™ 427 is an air compressor lubricant
designed to meet the requirements of the major compressor manufacturers. It is formulated with high quality
mineral base oils and an additive system designed
to provide equipment protection and reliability. Mobil
Rarus 427 provides good wear protection and air-oil
separation, and limits valve deposits.
Product
ISO VG
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Flash Point,
°C, ASTM D92
Mobil Rarus 427 104.6 11.6 100 264
100 21 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
COMPRESSOR OILS
Exxcolub™ SCF PS. These premium quality synthetic
blend gas compressor lubricants combine hydro
treated mineral oil and polyalphaolefin (PAO) synthetic
hydrocarbon oil. The proprietary multi-function silicone
additive enhances lubricity and minimizes foaming.
A pour point depressant improves low temperature
performance. A proprietary additive system reduces
the effects of corrosive materials present in compressor streams, where lubricant is typically subjected to
harsh chemicals, including hydrogen sulphide.
Exxcolub™ SCF M2. These premium hydrotreated
paraffinic gas compressor lubricants are blended
with a proprietary multi-function silicone additive to
enhance lubricity and minimize foaming. A pour point
depressant strengthens low temperature performance.
Exxcolub SCF M2 oils are recommended for applica-
tions where lubricant is subjected to harsh chemical
environments, including the presence of hydrogen
sulphide. Also recommended for rotary screw, vane
and reciprocating compressors in industrial applications requiring a higher viscosity lubricant.
Product
ISO VG
100
150
190
100
150
100
150
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
96
133
195
101
144
94
153
17.6
26
35.1
13.5
17.6
11.8
17.1
202
232
226
135
135
116
121
-48 max
-42 max
-43 max
-33 max
-33 max
-37 max
-30 max
218
257
304
277
288
248
271
MARINE
Exxcolub SCF PG 100
Exxcolub SCF PG 150
Exxcolub SCF PG 190
Exxcolub SCF PS 100
Exxcolub SCF PS 150
Exxcolub SCF M2 100
Exxcolub SCF M2 150
PASSENGER
long service life in high temperature operations.
Inherently high viscosity indexes (>200) facilitate low
temperature startup and help maintain acceptable
viscosity over a wide temperature range. Polyalkylene
Glycols are highly stable even at sustained high
temperatures; this helps keep deposits to a minimum.
COMMERCIAL
Exxcolub™ SCF PG. These custom-blended
Polyalkylene Glycol (PAG) synthetic lubricants deliver
excellent performance in severe-service gas compressor applications, exceeding the capabilities of petroleum-base and many synthetic-base lubricants.
Excellent oxidative and thermal stability helps assure
INDUSTRIAL
INDUSTRIAL LUBRICANTS
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
22
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
COMPRESSOR OILS
Lubricant
Benefits
Especially recommended for
Exxcolub SCF PG
Polyalkylene glycol
synthetic formula
Grades: 100 & 150
• Approximately twice as resistant as
mineral oils to gas dilution
• Sour gas and high CO2 applications
• Powerful corrosion inhibitors minimize
risk of corrosion from hydrogen sulphide
• Will allow a maximum of 20 percent
(by weight) hydrocarbon dilution
Exxcolub SCF PS
Synthetic blend
Grades: 100 & 150
• Lighter than water, effective waterresistance and demulsibility
• Silicone based corrosion inhibitors
lessen the risk of corrosion from
hydrogen sulphide
• Heavy hydrocarbons where severe
dilution may occur
• Cold weather conditions, especially
for compressing gas of high specific
gravity in cold weather
• Gas of low specific gravity under
cold weather conditions and requiring
a cost-effective alternative to a
synthetic lubricant
• Very low vapour pressure minimizes
lubricant consumption
Exxcolub SCF M2
Group ll mineral oil
Grades: 100 & 150
• Control over carbon and varnish,
with the potential for extended oil
drain intervals
• Light hydrocarbons, sour gas and low
water content where a modestly priced
lubricant is required
• Silicone based corrosion inhibitors
minimize risk of corrosion from
hydrogen sulphide
23 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
COMPRESSOR OILS
Mobil™ Compressor Oils provide outstanding lubrication in rotary and reciprocating air compressors. All
viscosity grades deliver outstanding oxidation performance, wear protection, resistance to rust and corrosion,
rapid water separation and foam control. Their thermal
Mobil Compressor Oil 68
Mobil Compressor Oil 122
Mobil Compressor Oil 220
68
–
220
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
68
122
220
9.1
12.3
18.4
-21
-15
-12
240
230
245
Product
ISO VG
Mobil Compressor Oil 264
Mobil Compressor Oil 460
–
460
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
280
485
23
35
-12
-12
280
280
Mobil Compressor Oil N 100
100
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
98
9
-51
200
Teresstic AC 32
32
with silver plated components – requiring a mineral
type oil that does not contain anti-wear additives.
(For applications requiring anti-wear properties,
Nuto H oils are recommended.)
AVIATION
Mobil Teresstic™ AC 32 is a compressor and circulating oil formulated primarily for applications in ammonia
production and chemical plants. Mobil Teresstic AC 32
is well suited for hydraulic systems – such as those
Product
ISO VG
exposed to very high surface film temperatures, this
oil produces miniscule amounts of soft, fluffy carbon
deposits that are easily displaced. This product can
also be used as a general purpose ISO 100 lubricant.
MARINE
Mobil™ Compressor Oil N 100. This premium
ISO 100 viscosity mineral oil blend is particularly well
suited as a once-through cylinder lubricant in large
reciprocating compressors where heavy exhaust valve
deposits have been observed with other oils. When
Product
ISO VG
with scrubber solution. They are ideally suited for
initial break-in of compressor cylinders and packing.
Both grades are formulated for outstanding cylinder
and piston ring lubrication, oxidation resistance and
chemical tolerance.
PASSENGER
Mobil™ Compressor Oils 264 and 460 are formulated
with highly refined paraffin base oils and proprietary
additive technology for compressor cylinders and packing. These high viscosity lubricants are recommended
for applications where gas is sour, wet or contaminated
COMMERCIAL
Product
ISO VG
stability and oxidation resistance help maintain clean
compressors, enabling longer running periods between
scheduled maintenance and oil changes. Outstanding
anti-wear and corrosion protection help enhance equipment life, while reducing maintenance requirements.
INDUSTRIAL
INDUSTRIAL LUBRICANTS
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
32
5.13
-40
204
Additional Compressor Oil
Mobil SHC Cibus™ Series......................................... 27
Click Here to return to PRODUCT APPLICATION INDEX
24
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
CYLINDER OILS
Mobil™ Cylinder Oils are high performance high
viscosity oils designed for use in enclosed worm gears
operating at moderate to high speeds and temperatures, and where heavy loads, slow speeds or high
temperatures demand high viscosity oils. They are
also intended for use in steam engines, natural gas
compressors requiring a separate cylinder lubricant,
Product
ISO VG
Mobil 600 W Cylinder Oil Mobil 600 W Super Cylinder Oil Mobil Extra Hecla Super Cylinder Oil -- 460 680 Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
375 460 680 27.0 30.5 35.8 95 95 85 -9 -6 0
282
282
282
Mobil DTE™ Oil 205 is a lubricating oil formulated
to provide excellent anti-wear and friction reducing
properties for compressor cylinder lubrication, as well
as protection against rust and corrosion. Mobil DTE
Oil 205 is designed for wet-gas compression and
Product
Mobil DTE Oil 205 and down-hole applications. They are formulated from
high quality base stocks that are resistant to oxidation
and thermal degradation, and the build-up of harmful
deposits caused by the high operating temperatures
of steam cylinders. They protect against rust and
corrosion, provide good film strength and excellent
lubricity and they are resistant to water washout.
exhibits excellent resistance to washing by water and
other entrained liquids. It resists oxidation and provides
effective lubrication at low feed rates, helping to extend
operating periods between valve-cleaning intervals.
Viscosity, ASTM D445
Spec. Gravity,
cSt at
cSt at
Pour Point,
Flash Point,
kg/l at 15.6°C,
40°C100°C
°C, ASTM D97
°C, ASTM D92
ASTM D1298
220 19.5 25 Visit mobil.ca /pds for the most current product information
-9 282 0.90
Click Here to return to PRODUCT APPLICATION INDEX
FOOD INDUSTRY LUBRICANTS
Mobil™ Food and Beverage Industry
141500
Mobil SHC Cibus™ 46
51524-HLP
51506-VDL
141498
Mobil SHC Cibus™ 68
51524-HLP
51506-VDL
141499
Mobil SHC Cibus™ 150
51517-CLP
141502
Mobil SHC Cibus™ 220
51517-CLP
141503
Mobil SHC Cibus™ 320
51517-CLP
141505
Mobil SHC Cibus™ 460
51517-CLP
141501
Mobil Glygoyle™ 460
KP1K-20
136467
Mobilgrease™ FM Series
(101)
KP1K-20
141881
Mobil SHC Polyrex™ Series
KPFHC2P-20
(462)
MARINE
51524-HLP
PASSENGER
Mobil SHC Cibus™ 32
contamination from lubricating oils and greases.
This comprehensive suite of high performance oils are
NSF H1 registered, which is increasingly being requested
by major food retailers and government agencies.
COMMERCIAL
The food and beverage processing industry faces
unique challenges. Not only must you strive for
maximum productivity, you must also guard against
the possibility of food contamination, including
INDUSTRIAL
INDUSTRIAL LUBRICANTS
138558
AVIATION
Other Food Industry Lubricants
• Mobil DTE™ FM (32, 46, 68): premium mineral oils
• Mobil Synturion™ 6: synthetic mechanical seal fluid
• Mobil Gargoyle Arctic SHC™ Series: synthetic refrigeration lubricants
Click Here to return to PRODUCT APPLICATION INDEX
26
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
FOOD INDUSTRY LUBRICANTS
Mobil SHC Cibus™ Series lubricants are superb
performance synthetic, compressor, hydraulic, gear
and bearing oils designed to provide outstanding
equipment protection, long oil life and problem-free
Product
ISO VG
Mobil SHC Cibus 32 Mobil SHC Cibus 46 Mobil SHC Cibus 68 Mobil SHC Cibus 100 Mobil SHC Cibus 150 Mobil SHC Cibus 220 Mobil SHC Cibus 320 Mobil SHC Cibus 460 32 46 68 100 150 220 320 460 Viscosity, ASTM D445 Spec. Gravity
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
kg/l at 15°C,
ASTM D4052
30 43 72 102 162 222 311 458 5.8 7.7 11.4 14.6 20.7 24.5 32.7 43.6 140 148 151 148 150 139 147 148 <-54 -51
-48
-48
-21
-39 -42 -42
253 258
267 273
226
274 284 294
0.829
0.833
0.838
0.839
0.843
0.843
0.854
0.856
Mobil DTE™ FM Series oils meet a wide range
of multi-use requirements for equipment in food
processing and packaging. These lubricants are
qualified as NSF H1 type lubricants and comply
with Title 21 CFR 178.3570 by the Food and Drug
Product
ISO VG
Mobil DTE FM 32 Mobil DTE FM 46 32 46 operation in the food and beverage processing
and packaging industries. They are formulated from
FDA and NSF registered hydrocarbon base fluids
and additives.
Administration (USA) for lubricants with incidental
food contact. These odourless, tasteless, premium
quality lubricants are formulated with non-toxic
NSF/FDA additives and base oils.
Viscosity, ASTM D445Spec. Gravity
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
kg/l at 15.6°C,
ASTM D4052
31.9 45.5 5.5 6.8 106 105 -12 -9 212 226 0.862
0.868
Additional Food Industry Lubricants
Mobil Synturion™ 6.................................................... 46
Mobil Gargoyle Arctic SHC™ Series.......................... 49
27 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
GAS ENGINE OILS
Imperial Engine Recommendation – How to Select the Right Oil
Model
Product
Ajax
2-cycle
Mobil Pegasus AGX;
Mobil Pegasus 801
Caterpillar
All models
Mobil Pegasus 1; Mobil Pegasus GMA;
Mobil Pegasus 805
Clark (Dresser-Rand)
All 2-cycle
Mobil Pegasus AGX;
Mobil Pegasus 801
Cooper-Bessemer
All 2-cycle
Mobil Pegasus AGX;
Mobil Pegasus 801
Cummins
Most models
Mobil GEO 15W-40
B & C models
Mobil GEO 15W-40
Cooper Enterprises (Delaval)
All models
Mobil Pegasus 801
Fairbanks-Morse (M.E.P.)
2-cycle
Mobil Pegasus 801 SAE 30;
Mobil Pegasus 801; Mobil Pegasus GMA
Ingersoll-Rand (Dresser-Rand)
Categories I, II, III
Mobil Pegasus 801 SAE 30
Jenbacher
Type 2 & 3 Leanox Engines
Mobil Pegasus 805; Mobil Pegasus 710
White Superior
4-cycle
Mobil Pegasus GLX; Mobil Pegasus 710
1700 & 2400
Mobil Pegasus GMA; Mobil Pegasus 1;
Mobil Pegasus GLX
Worthington
All models
Mobil Pegasus 801 SAE 30
Waukesha
VSG F11 (G, GSI, GSID)
Mobil Pegasus 1; Mobil Pegasus GMA;
Mobil Pegasus 805; Mobil Pegasus GLX;
Mobil Pegasus 710
VGF F18, H24, L36, P48
(G, GL, GLD/GLD2)
Mobil Pegasus 1; Mobil Pegasus GMA;
Mobil Pegasus 805; Mobil Pegasus GLX;
Mobil Pegasus 710
VGF F18, H24, L36, P48
(GSI, GSID)
Mobil Pegasus 1; Mobil Pegasus GMA;
Mobil Pegasus 805; Mobil Pegasus GLX;
Mobil Pegasus 710
VHP F2895, F3521, L5790,
L7042, P9390 (G, GSI, GL)
Mobil Pegasus 1; Mobil Pegasus GMA;
Mobil Pegasus 805; Mobil Pegasus GLX;
Mobil Pegasus 710
VHP F3524, L5794,
L5790 (GSI), L5774,
L5794 (LT)
Mobil Pegasus 1; Mobil Pegasus GMA;
Mobil Pegasus 805; Mobil Pegasus GLX;
Mobil Pegasus 710
AT – All models
(275GL/GL+ AT25/27 GL)
Mobil Pegasus 1; Mobil Pegasus GMA;
Mobil Pegasus 805; Mobil Pegasus GLX;
Mobil Pegasus 710
COMMERCIAL
Manufacturer
PASSENGER
GREASES
28
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
MARINE
Please refer to OEM manual for lubricant recommendations or contact your Imperial sales representative.
Visit mobil.ca /pds for the most current product information
INDUSTRIAL
INDUSTRIAL LUBRICANTS
INDUSTRIAL LUBRICANTS
GAS ENGINE OILS
Mobil SHC Pegasus™ 30 is a recently developed
category of synthetic natural gas engine oil designed
to provide today’s high output, low emission four-cycle
gas engines with advanced levels of wear protection
and fuel efficiency. Mobil SHC Pegasus 30 delivers
high performance, long service life and improved
productivity through a patented combination of high
quality base stocks and advanced additive technology.
The result is exceptional oxidation stability, nitration
resistance and thermal stability, which may enable
drain intervals to be extended by up to three times that
SAE
Product
Grade
Mobil SHC Pegasus 30 30 Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
65 10.5 162 -51 255 Mobil Pegasus™ 1 is a high performance synthetic
gas engine oil designed to meet the highest performance requirements of some of the most demanding
naturally aspirated and turbocharged stoichiometric
and lean-burn gas engines. Formulated from wax-free
SAE
Product
Grade
Mobil Pegasus 1 15W-40 Mobil Pegasus GMA
40
Mobil Pegasus 805 40 5
0.5
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
93.8 13.0 137 -48 238 TBN, mg KOH/g,
Sulfated Ash,
ASTM D2896 wt% ASTM D874
6.5 0.5
is 0.57 % mass. The balanced additive system provides
excellent control of viscosity, oxidation and nitration.
Mobil Pegasus GMA protects against varnish, corrosion, deposits and wear, while minimizing premature
valve recession.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
115
13.2
110
-21
Mobil Pegasus™ 805 is a premium performance gas
engine oil engineered to meet the rigorous demands
of high output four-cycle engines designed to reduce
emissions and improve fuel efficiency. Such engines
generally operate under high load and high temperature
conditions. The highest quality base stocks and an
SAE
Product
Grade
TBN, mg KOH/g, Sulfated Ash,
ASTM D2896
wt% ASTM D874
synthetic base oils and a balanced additive system,
this oil delivers performance that is unattainable with
conventional mineral oil based gas engine oils. Potential benefits Include longer engine and oil life, reduced
maintenance and lower fuel costs.
Mobil Pegasus™ GMA, our premium low ash natural
gas engine oil, is the prime recommendation for
Caterpillar and Waukesha natural gas engines and is
formulated to provide excellent performance through
extended oil drain intervals. Typical sulphated ash
SAE
Product
Grade
of conventional gas engine oils. Mobil SHC Pegasus
30 provides outstanding anti-wear performance to
protect heavily loaded valve train components, pistons,
liners, bearings, and gear trains while maintaining
compatibility with catalytic converter materials. An
effective detergent-dispersant system controls carbon
and varnish deposits to minimize oil consumption and
maintain engine cleanliness – even through extended
drain intervals, which may result in lower operating
and maintenance costs. For information on energy
efficiency, please see page 7.
Flash Point, TBN, mg KOH/g,
°C, ASTM D92
ASTM D2896
240
6
Viscosity, ASTM D445 Spec. Gravity
cSt at
V.I. TBN, mg KOH/g,
kg/l at 15.6°C,
100°C
ASTM D2270
ASTM D2896
ASTM D4052
13.5 0.57
advanced technology additive system combine to
deliver exceptional oxidation stability, nitration resistance and thermal stability. An effective detergent and
dispersant system controls carbon deposits, lacquer
and sludge.
cSt at
40°C
130 Sulfated Ash,
wt% ASTM D874
99 29 Visit mobil.ca /pds for the most current product information
6.2 0.89 Sulfated Ash,
wt% ASTM D874
0.5
Click Here to return to PRODUCT APPLICATION INDEX
GAS ENGINE OILS
Mobil Pegasus™ GLX meets the requirements
of most four-cycle high speed natural gas engines,
including Superior and Waukesha VSG, VGF, VHP
and AT. The medium ash additive system protects
Mobil Pegasus GLX
40
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
127
13.2
95
-18
250
Mobil Pegasus™ 710 is a premium performance gas
engine oil intended primarily for modern high speed
four-cycle engines where oil consumption is very low
and where increased manifold pressures may keep
some lubricants from reaching the valve guide areas in
sufficient quantities. This oil is also recommended for
Mobil Pegasus 710 40 Viscosity, ASTM D445 Spec. Gravity
cSt at
cSt at
V.I. TBN, mg KOH/g,
kg/l at 15.6°C,
40°C
100°C
ASTM D2270
ASTM D2896
ASTM D1298
121 13.2 98 40 6.5 0.896 Sulfated Ash,
wt% ASTM D874
1.0
recession, increasing the potential for upper cylinder
components being attacked by acidic materials generated through combustion. Mobil Pegasus 610 is a 1.0%
ash, high TBN gas engine oil with exceptional reserve
alkalinity to offset the negative effects of corrosive materials on engine components. This protection extends
to cylinders, valve areas and bearings resulting in long
engine life and low maintenance costs.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
TBN, mg KOH/g,
ASTM D2896
Sulfated Ash,
wt% ASTM D874
130 13.8 102 -18 264 8.6 1.0
MARINE
Mobil Pegasus 610 0.8
gas compressors. High quality mineral base oils and an
advanced medium ash additive system provide excellent
protection of engine and compressor components. Mobil
Pegasus 710 delivers effective detergency and dispersancy, along with chemical stability and resistance to
oxidation, nitration, valve train wear and deposits.
Mobil Pegasus™ 610 is a high performance natural
gas engine oil intended primarily for modern medium
and high speed four-cycle engines operating on fuel
containing corrosive materials such as hydrogen
sulphide or halogens (compounds containing chlorine,
fluorine, etc.). In these typically lean-burn engines
increased manifold pressures can prevent sufficient
lubricant from reaching the valve guide areas. This
often leads to accelerated valve guide wear and valve
SAE
Product
Grade
6.0
PASSENGER
SAE
Product
Grade
TBN, mg KOH/g, Sulfated Ash,
ASTM D2896 wt% ASTM D874
COMMERCIAL
SAE
Product
Grade
against piston scuffing, cylinder wear, corrosion and
deposits. The formulation leaves a cushioning ash to
help control valve recession. Phosphorous content is
low enough for catalyst exhaust systems.
INDUSTRIAL
INDUSTRIAL LUBRICANTS
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
30
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
GAS ENGINE OILS
Mobil Pegasus™ 605 is a high performance natural
gas engine oil primarily intended for modern medium
and high speed four-cycle engines operating on fuel
that contains corrosive materials such as hydrogen
sulphide or such halogens as chlorine, fluorine or
bromine. Exceptional reserve alkalinity helps offset
the negative effects of acidic materials on engine components. Excellent corrosion protection helps prevent
corrosive wear in cylinders, valve areas and bearings,
promoting long engine life and low maintenance costs.
SAE
Product
Grade
Mobil Pegasus 605 40 Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
120 13.2 104 -15 246 Mobil Pegasus™ 801 Series is a premium performance gas engine oil intended for the lubrication of all
classes of gas engines operating at low, medium and
high speeds where low ash or ashless oils are recommended. It provides outstanding engine cleanliness and
performance by preventing the formation of carbon and
ash deposits on pistons, in ring belt areas, on exhaust
and intake ports, on valves and valve stems and in com
SAE
Product
Grade
Mobil Pegasus 801 Mobil Pegasus 801 SAE 30 40 30 Mobil Pegasus AGX
40
TBN, mg KOH/g, Sulfated Ash,
ASTM D2896 wt% ASTM D874
4.9 132 85 13.2 10.0 0.5
bustion chambers. Mobil Pegasus 801 – SAE 30 also
reduces the potential for port carboning of two-cycle
gas engines. It helps minimize engine wear and protect
valve faces, seats and guides of turbocharged four-cycle
engines. Mobil Pegasus 801 – SAE 30 provides exceptional protection against scuffing in demanding engine
applications and also provides excellent protection
against corrosion of internal engine components.
Viscosity, ASTM D445 Spec. Gravity
cSt at
cSt at
V.I. TBN, mg KOH/g,
kg/l at 15.6°C,
40°C
100°C
ASTM D2270
ASTM D2896
ASTM D1298
97 97 Mobil Pegasus™ AGX employs a highly effective
ashless anti-wear additive to guard against ring and
liner wear and cylinder scuffing. Ashless detergent/dispersant additives deliver excellent control over sludge
SAE
Product
Grade
Excellent deposit control helps prevents siloxane
deposits and liner laquering in biofuel and landfill gas
applications with high silicon content. Preventing these
deposits is a key step in controlling lube oil consumption. Mobil Pegasus 605 can be used for the lubrication
of the reciprocating compressors in landfill, mine, coal
seam, digester/fermenter, sewage and other biomass
gas operations in municipal, industrial, cooperative and
farm applications, including electric power generation,
boiler heating, cogeneration/combined heat and power.
2.8 2.8 –
0.882 Sulfated Ash,
wt% ASTM D874
0.1
0.1
and varnish deposits, including carbon in the ports.
It is formulated with an inherently oxidation-resistant
paraffinic base oil with potent anti-wear agents to guard
against wear, particularly in rings, liners and cylinders.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
135
13.5
95
-21
250
TBN, mg KOH/g, Sulfated Ash,
ASTM D2896 wt% ASTM D874
2.5
0.04
Additional Gas Engine Oils
Mobil Delvac™ CNG/LNG 15W-40............................. 62
Mobil GEO™ 15W-40................................................. 62
31 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
GAS ENGINE OILS
Imperial Engine Recommendation – How to Select the Right Oil
% SASH
Ashless
0.13
Mobil Pegasus™ AGX
Ashless
0.03
Mobil SHC Pegasus™ 30
Low Ash
0.50
Mobil Pegasus™ 605
Low Ash
0.52
Mobil Pegasus™ 805
Low Ash
0.54
Mobil Pegasus™ 1
Low Ash
0.54
Mobil Pegasus™ GMA
Low Ash
0.57
Mobil GEO™ 15W-40
Low Ash
0.54
Mobil Pegasus™ 610
Medium Ash
0.98
Mobil Pegasus™ 710
Medium Ash
0.94
Mobil Pegasus™ GLX
Medium Ash
0.80
MARINE
Mobil Pegasus™ 801
PASSENGER
Category
COMMERCIAL
Natural Gas Engine Oil
INDUSTRIAL
INDUSTRIAL LUBRICANTS
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
32
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
GEAR OILS — ENCLOSED GEARS
Mobil SHC Gear™ Series (ISO VG 150-1000) lubricants are recognized around the world for innovation
and outstanding performance. These synthetic products are designed to provide outstanding protection of
gears and bearings, and extended oil life even under
extreme conditions. This promotes problem-free operation of equipment and increased productivity. Synthetic
base fluids with exceptional oxidation and thermal
properties deliver excellent low temperature fluidity.
The high viscosity index of these oils means less
change in viscosity as temperatures change, enabling
a wider operating temperature range and improved low
Product
ISO VG
Mobil SHC Gear 150 Mobil SHC Gear 220 Mobil SHC Gear 320 Mobil SHC Gear 460 Mobil SHC Gear 680 Mobil SHC Gear 1000 150 220 320 460 680 1000 Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
150 220 320 460 680 1000 22.2 30.4 40.6 54.1 75.5 99.4 176 180 181 184 192 192 -54 -45 -48 -48 -42 -33 233 233 233 234 234 234 Mobil SHC Gear™ 1500, 3200, and 6800 are
high performance heavy duty gear oils primarily
designed for enclosed gearing as well as slow speed
plain and rolling element bearings. They are designed
to provide outstanding service in terms of equipment
protection, oil life, and problem-free operation enabling
increased customer productivity. These scientifically
engineered synthetic lubricants are formulated from
synthetic base fluids that have exceptional oxidation
and thermal properties and excellent low temperature
fluidity. The combination of a naturally high viscosity
index and a unique additive system enables these
Product
ISO VG
Mobil SHC Gear 1500 Mobil SHC Gear 3200 Mobil SHC Gear 6800 1500 -- -- temperature startup. An advanced proprietary additive
system provides excellent protection against scuffing
and a high level of resistance against micropitting
fatigue. Mobil SHC Gear Series oils have outstanding
EP properties that protect even under shock load
conditions. The synthetic base stocks have inherently
low traction properties, resulting in low fluid friction
in the load zone of non-conforming surfaces, such
as gears and rolling element bearings. Reduced fluid
friction also produces lower operating temperatures
and improved gear efficiency. For information on
energy efficiency, please see page 7.
FZG Scuffing,
FZG Scuffing,
ISO 14635-1 (mod)
ISO 14635-1 (mod)
A/8.3/90, Fail Stage A/16.6/90, Fail Stage
13 14 14 14 14 14 Not tested
>14
>14
>14
>14
>14
products to provide outstanding performance under
severe high and low temperature operating conditions.
The nature of the synthetic base fluids also contributes
to the products’ excellent low temperature performance.
They have excellent protection against gear scuffing
and resistance to shock loading. The synthetic base
stocks have inherently low traction properties that
result in low fluid friction in the load zone of nonconforming surfaces such as gears and rolling element
bearings. Reduced fluid friction produces lower operating temperatures and improved gear efficiency.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
FZG test,
ISO 14635-1 mod.,
Failure Stage
1500 3200 8200 113 183 365 165 165 180 -18 -9 -6 230 230 230 13+
13+
13+
33 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
GEAR OILS — ENCLOSED GEARS
Product
Mobilgear 600 XP 68 Mobilgear 600 XP 100 Mobilgear 600 XP 150 Mobilgear 600 XP 220 Mobilgear 600 XP 320 Mobilgear 600 XP 460 Mobilgear 600 XP 680 trends toward smaller units with similar power throughput. This increase in power density places increased
demands on lubricant. Mobilgear 600 XP Series oils
meet the stress by providing extra protection for gears,
bearings and seals.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I. ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
68 100 150 220 320 460 680 8.8 11.2 14.7 19.0 24.1 30.6 39.2 101 97 97 97 97 96 90 -27 -24 -24 -24 -24 -15 -9 230 230 230 240 240 240 285 12+ 12+ 12+ 12+ 12+ 12+ 12+ –
12+
12+
12+
12+
12+
12+
bility and excellent protection from wear. The thermal
stability of SPARTAN EP-C helps reduce sludge formation and keep internal surfaces clean. SPARTAN EP-C
oils provide excellent protection against corrosion of
steel and copper containing alloys. They also have
excellent demulsibility, so that water separates rapidly
from the oil, simplifying drain off from gear cases and
system reservoirs.
PASSENGER
SPARTAN™ EP-C is the brand name for a family
of premium quality industrial extreme pressure gear
lubricants. They are formulated with high quality
mineral oils and carefully selected high performance
additives that work synergistically to provide excellent
gear protection and long lubricant life. SPARTAN EP-C
oils contain a sulphur/phosphorus Extreme Pressure
additive system that provides high load-carrying capa-
FZG scuffing,
FZG scuffing,
Fail Stage A/8.3/90 Fail Stage A/16.6/90
COMMERCIAL
Mobilgear™ 600 XP Series high performance gear
oils have excellent extreme pressure characteristics
and load-carrying properties. They are intended for use
in all types of enclosed gear drives with circulation or
splash lubrication systems. These oils are designed
to stay ahead of gearbox technology, including design
INDUSTRIAL
INDUSTRIAL LUBRICANTS
Kinematic Viscosity cSt at
V.I. Pour Point,
Flash Point,
100°C
ASTM D2270
°C, ASTM D97
°C, ASTM D92
cSt at
40°C
Spartan All-Season Spartan 1000 150 1000 21.5 47.5 170 90 -36 -9 192
246 MARINE
Product
Additional Enclosed Gears
Mobil SHC™ 600 Series............................................ 19
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
34
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
GEAR OILS — ENCLOSED GEARS SPECIALTY
Mobil SHC™ Gear OH Series. These exceptional performance synthetic gear oils are primarily designed to
lubricate enclosed gears and plain and rolling element
bearings in off-highway equipment subject to shock and
heavy loading. They provide outstanding equipment
protection, oil life and problem-free operation, promoting
increased productivity. The synthetic base fluids deliver
exceptional oxidation and thermal properties and
excellent low temperature fluidity, contributing significantly to low temperature performance. Synthetic base
stocks have inherently low traction properties that result
in low fluid friction in the load zone of non-conforming
Product
ISO VG
Mobil SHC Gear OH 320 Mobil SHC Gear OH 460 Mobil SHC Gear OH 680 320 460 680 Kinematic Viscosity,
Viscosity, ASTM D445
FZG Gear Scuffing,
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D5950
Flash Point,
°C, ASTM D92
(A/8.3/90), ISO 14635-1
mod Failure Stage
320 460 680 40.1 54.9 76.1 178 186 193 -45 -42 -39 233 233 233 >13
>13
>13
Mobilgear SHC™ XMP Series lubricants are high
performance synthetic wind turbine gear oils providing
outstanding equipment protection and oil life, even
under extreme conditions. Our synthetic base oil
technology provides exceptional oxidation resistance
and thermal properties, naturally high viscosity index,
excellent low temperature fluidity and the absence of
undesirable compounds often found in mineral oils.
A high viscosity index and low traction coefficient
Product
ISO VG
Mobilgear SHC XMP 320 320 surfaces such as gears and rolling element bearings.
Reduced fluid friction produces lower operating temperatures and improved gear efficiency. A naturally high
viscosity index and unique additive system combine
to provide outstanding performance under severe high
and low temperature operating conditions. Mobil SHC
Gear OH Series oils deliver outstanding gear scuffing
protection in heavily loaded gearboxes. Their available
viscosity range: ISO VG 320 to 680. These are the
products of choice for key OEMs and customers with
demanding off-highway applications. For information
on energy efficiency, please see page 7.
combine for a significant reduction in power consumption in many gear drives. An advanced proprietary
additive system helps prevent conventional wear such
as scuffing and provides high resistance to micropitting
fatigue. Mobilgear SHC XMP oils deliver outstanding
rust and corrosion protection and show no tendency
to plug fine filters even when wet. Compatibility with
ferrous and non-ferrous metals, even at elevated
temperatures, is excellent.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Spec. Gravity
kg/l at 15.6°C,
ASTM D4052
FZG Scuffing,
DIN 51345 (mod)
A/16.6/90, Fail Stage
335 38.3 164 -38
242 0.860 14+
Mobil Glygoyle™ Series lubricants are high performance gear, bearing and compressor oils delivering
outstanding efficiency, long oil life, and equipment
protection. These synthetic polyalkylene glycol (PAG)
oils were designed for operating conditions beyond
the capabilities of other synthetic lubricants and mineral
oils. Their low pour points ensure excellent lowtemperature fluidity.
Viscosity, ASTM D445
Product
ISO VG
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
FZG Test, ISO.
Fail Load Stage
Mobil Glygoyle 460 460.0 77.2 250 -33 265 12+
460 35 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
GEAR OILS — ENCLOSED GEARS SPECIALTY
Mobil Iogear™ EP 100 is an extreme pressure gear
oil specially designed for oil field pump jack gear drives
and formulated to operate across a wide temperature
Viscosity, ASTM D445
SAE
Product
Grade
100
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
99.5
14.96
157
-40
170
Additional Enclosed Gears Specialty
Mobil SHC Cibus™ Series......................................... 27
INDUSTRIAL LUBRICANTS
COMMERCIAL
Mobil IOGear EP 100
range for year-round performance. It is well suited
for other gear applications requiring excellent
low temperature performance.
INDUSTRIAL
INDUSTRIAL LUBRICANTS
GEAR OILS — OPEN GEARS
high viscosity index and unique additive system
combine to provide exceptional thermal/oxidative
properties and outstanding performance under severe
high and low temperature operating conditions, even
with very slow moving gears. The additive formulation
also provides excellent gear scuffing protection, antiwear performance and rust and corrosion inhibition.
Viscosity, ASTM D445
Product
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Mobil SHC Gear 46M 46,000 1375 180 15
240
Product
consistency that is maintained throughout its service
life. Mobiltac 375 NC adheres strongly to gear teeth and
other machine elements to resist excessive throw-off,
providing a wear resistant, viscous, continuous film that
lubricates well under boundary conditions.
Mobiltac 375 NC is available in spray cans.
Spec. Gravity
Flash Point,
kg/l at 15.6°C,
°C, ASTM D92 ASTM D1298
cSt at 40°C
w/diluent
cSt at 100°C
w/o diluent
5000 1260 Mobil Geargard™ HVS is an ultra-high viscosity
lubricant primarily intended for heavily loaded, low
and medium speed open gears that may operate in
boundary lubrication conditions. The ultra-high viscosity
synthetic fluid combines with extreme pressure additives
135 Smooth
Visit mobil.ca /pds for the most current product information
110
Viscosity, ASTM D445
cSt at 40°C
without diluent
cSt at 100°C
without diluent
44000
1350
Click Here to return to PRODUCT APPLICATION INDEX
36
GREASES
Black
0.96
to provide outstanding performance under severe
conditions. Geargard HVS dispenses well in ambient
temperatures as low as -10°C, while providing excellent
gear protection at high operating temperatures.
Colour,
Flash Point,°C
Product
Visual
Structure
with diluent
Mobil Geargard HVS
0.924
AVIATION
Mobiltac 375 NC Viscosity, ASTM D445
Spec. Gravity
kg/l at 15.6°C,
ASTM D4052
MARINE
Mobiltac™ 375 NC is an high performance non-leaded, diluent-type, heavy bodied open gear lubricant
designed for a wide variety of open gear and mining
applications. A non-chlorinated, volatile solvent ensures fluidity during application, even at low temperatures. Once applied, the diluent evaporates and the
lubricant takes on a flexible, adhesive, high strength
PASSENGER
Mobil SHC Gear™ 46M is a high performance ultra
high viscosity synthetic lubricant designed specifically
for heavily loaded, low speed open gears where boundary lubrication conditions often prevail. Synthetic base
stocks provide remarkable low temperature fluidity; they
can be pumped over relatively long distances and
applied with standard spray equipment. The naturally
INDUSTRIAL LUBRICANTS
HEAT TRANSFER FLUIDS
Mobiltherm™ and Thermoil™ heat transfer fluids offer
many years of successful service in such industries
as plastics, paint, rubber, paper mill calendars, board
plants, roofing, textiles and refineries. Highly refined
Viscosity, ASTM D445
Product
ISO VG
Mobiltherm N 100 Thermoil 32
Thermoil 46
Thermoil 100
mineral base stocks and select additive technology
combine for excellent thermal and oxidation stability.
The volatility and flash points are optimized to reduce
vapour pressure at elevated temperatures.
100
32
46
100
cSt at
40°C
cSt at
100°C
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
108
32
46
100
11.8
5.31
6.67
10.78
-18
<-24
<-24
<-12
261
205
212
252
INDUSTRIAL LUBRICANTS
HYDRAULIC FLUIDS
Mobil SHC™ 500 Series are our highest performance
hydraulic oils and have the widest temperature range
capability. These synthetic fluids have exceptional
shear-stability and wear protection and are designed
for extended service in high pressure, high temperature vane, piston and gear pump applications where
Viscosity, ASTM D445
Product
ISO VG
Mobil SHC 524 Mobil SHC 525 Mobil SHC 526 Mobil SHC 527 sustained lubrication excellence is critical to productivity. Their superb low and high temperature properties
enable extraordinary low temperature pumpability and
startup, and ensure outstanding equipment protection
at extremely high temperatures. For information on
energy efficiency, please see page 7.
32 46 68 100 cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
32 46 68 100 6.4 8.54 11.52 15.94 144 154 158 160 -56
-54 -53
-52
234
238
240
243
Mobil DTE 10 Excel™ Series hydraulic oils deliver
superb performance and energy efficiency. These
ashless non-zinc oils are intended for high speed, high
pressure, high output piston, vane and gear pumps
operating under severe conditions where high levels
of anti-wear, film strength and high temperature protection are needed. For information on energy efficiency,
please see page 7.
Brookfield
Viscosity, ASTM D445
Viscosity, ASTM D2983
Product
ISO VG
cSt at
I40°C
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92 cP at
-20°C
cP at
-20°C
cP at
-40°C
Dielectric
Strength, kV,
ASTM D877
Mobil DTE 10 Excel 15 Mobil DTE 10 Excel 22 Mobil DTE 10 Excel 32 Mobil DTE 10 Excel 46 Mobil DTE 10 Excel 68 Mobil DTE 10 Excel 100 15.8 22.4 32.7 45.6 68.4 99.8 4.07 5.07 6.63 8.45 11.17 13.00 168 164 164 164 156 127 -54 -54 -54 -45 -39 -33 182 224 250 232 240 258 –
–
1090 1870 3990 11240 –
–
3360 7060 16380 57800 2620 6390 14240 55770 –
–
45
54
49
41
–
–
15 22 32 46 68 100 37 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
HYDRAULIC FLUIDS
Mobil DTE™ 20 Series oils are premium performance
anti-wear hydraulic oils that meet the stringent
requirements of hydraulic systems with high pressure,
high output pumps. Since they meet the rigorous
Mobil DTE 24 Mobil DTE 25 Mobil DTE 26 32 46 68 Viscosity, ASTM D445Spec. Gravity
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
kg/l at 15.6°C,
ASTM D1298
31.5 44.2 71.2 5.29 6.65 8.53 98 98 98 -27 -27 -21 220 232 236
0.871
0.876
0.881
temperature fluidity of an ISO VG 22. The all-weather
performance of Mobil Univis Ultra makes it the ideal
choice for stationary and mobile equipment in such
outdoor applications as oil and gas, mining, forestry
and construction.
Viscosity, ASTM D445
Product
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Mobil Univis Ultra
43.1
10.42
242
-54
196
Mobil Univis Extra
N-C line and provides outstanding oxidation resistance,
rust protection, demulsibility and foam control. It is
well suited for most pump types, including vane, axial
piston, radial piston and gear. This oil is recommended
for a variety of equipment operating over a wide range
of temperature, simplifying lube inventory by reducing
the number of fluids required.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
32.8
7.6
213
-50
170
MARINE
Mobil Univis™ Extra is a premium multigrade hydraulic
oil recommended for extreme climatic conditions. It
delivers the same outstanding low temperature performance as an ISO 22 grade oil along with excellent
protection at high temperatures, similar to an ISO 32
grade product. Mobil Univis Extra exhibits the excellent
wear-protection characteristics of the popular Univis
Product
PASSENGER
Mobil Univis™ Ultra is a premium all-season, multigrade hydraulic fluid that delivers excellent pumpabilitty
at extremely low temperatures and excellent protection
at all operating temperatures. It combines the high
temperature viscosity characteristics of an all-season
ISO VG 46 hydraulic oil with the outstanding low
COMMERCIAL
Product
ISO VG
requirements of a wide range of hydraulic system and
component manufacturers, these oils may simplify
lubricant inventory by enabling the use of a single
product with outstanding performance characteristics.
INDUSTRIAL
INDUSTRIAL LUBRICANTS
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
38
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
HYDRAULIC FLUIDS
Mobil Univis™ N-C Series. High viscosity indexes
and low pour points help ensure cold weather pump
startups while maintaining oil viscosity at high ambient
temperatures. A highly effective anti-wear additive
protects hydraulic pumps even in severe-service applications employing high pressure axial and radial piston
Product
Mobil Univis N-C 15
Mobil Univis N-C 22
Mobil Univis N-C 32
Mobil Univis N-C 46
Mobil Univis N-C 68
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
15
22
32
46
68
3.9
5.1
6.6
8.2
10.7
140
140
140
140
140
-54
-51
-48
-45
-42
150
156
204
218
226
Mobil Univis™ HVI 13 is a premium quality low viscosity hydraulic oil with an exceptionally high viscosity
index. Because of its resistance to viscosity change
with temperature, this fluid is highly recommended
for equipment subject to wide swings in temperature.
Applications include hydrostatic transmissions and fluid
systems, such as those of numerically controlled lathes
Product
Mobil Univis HVI 13 Mobil Univis BIO-C 40
and automatic screw machines. Mobil Univis HVI 13 can
also lubricate fine instruments and other mechanisms
where power input is limited and where increases in
torque due to lubricant thickening cannot be tolerated.
Other features include excellent lubrication, long-lasting
oxidation stability and a very low pour point.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
13.5 5.3 404 -60
Mobil Univis™ BIO-C 40 is a non-toxic, biodegradable
vegetable oil based hydraulic oil developed to meet
growing global demand for more environmentally
friendly lubricants. It is well suited for applications
Product
pumps. Mobil Univis N-C also delivers excellent rust
protection, good demulsibility, oxidation resistance and
anti-foam properties. Excellent all-season performance
can enable operators to standardize to one viscosity
grade for year-round service, simplifying lube inventory
by reducing the number of fluids required.
Flash Point,
°C, ASTM D92
101
demanding a high performance, anti-wear fluid in
woodland, construction, mining, marine and other
applications facing critical environmental concerns.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
43
9.7
200
< -36
>200
39 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
HYDRAULIC FLUIDS
Product
ISO VG
Mobil Nuto H 32
Mobil Nuto H 46
Mobil Nuto H 68
Mobil Nuto H 100
Mobil Nuto H 150
32
46
68
100
150
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
32
46
68
100
150
5.4
6.7
8.5
11.1
14.6
104
104
107
95
95
-36
-30
-30
-27
-24
212
226
234
242
258
Forum EP 46
Forum EP 68
46
68
pressure (EP) characteristics enable these fluids
to pass the rigorous Brugger load-carrying test,
as required for Mueller Weingarten presses. The
balanced additive system also delivers effective foam
and air release, oxidation control and demulsibility.
PASSENGER
Forum™ EP 46 and 68 are high performance
hydraulic and circulating oils developed for hydraulic
presses made by Mueller Weingarten, Voith-Vorecon
and Pahnke. These oils can also be used in other
applications requiring highly effective unique loadcarrying properties. Enhanced anti-wear and extreme
Product
ISO VG
stability, promoting long oil life and minimal deposits
in severe-service hydraulic systems and high pressure,
high output pumps. Anti-wear performance is excellent.
Highly effective foam and air release properties help
prevent erratic operation, high temperatures, wear,
cavitation damage and micro dieseling associated
with foam and air entrainment.
COMMERCIAL
Mobil Nuto™ H Series. These high performance
anti-wear hydraulic oils are specifically designed for
modern high pressure mobile and stationary hydraulic
systems. Premium quality base oils and high performance additives work synergistically to deliver well
balanced performance for a wide range of applications.
All viscosity grades exhibit good oxidation and thermal
INDUSTRIAL
INDUSTRIAL LUBRICANTS
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
46.1
66.9
6.9
8.8
105
103
-30
-24
214
228
MARINE
Additional Hydraulic Fluid
Mobil SHC Cibus™ Series......................................... 27
Mobil DTE™ FM Series.............................................. 27
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
40
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
HYDRAULIC FLUIDS — LESS FLAMMABLE
Mobil Nyvac™ FR 200D is an high performance
water-glycol type less flammable hydraulic fluid. It is
formulated with diethylene glycol as the main glycol
component. This product does not contain ethylene
glycol. It delivers excellent protection against rust
and vapour phase corrosion. In hydraulic pump tests,
Product
Mobil Nyvac FR 200D it has shown a high level of anti-wear performance.
A high viscosity index makes Mobil Nyvac FR 200D
effective over a wide range of operating temperatures.
Foam resistance, low temperature flow and storage
stability are also excellent.
Viscosity, ASTM D445
cSt at
40°C
V.I.
ASTM D2270
Pour Point, °C, ASTM D97 41.5 175 -30 Mobil Pyrogard™ 53 is a high performance
phosphate ester synthetic fluid designed to replace
petroleum based oils in hydraulic applications where
Spec. Gravity
kg/l at 15.6°C,
ASTM D1298
1.089
conditions preclude the use of combustible petroleum
products. Mobil Pyrogard 53 is approved by Factory
Mutual (FM) as a less flammable fluid.
Product
Viscosity, ASTM D445
Spec. Gravity
cSt at
cSt at
Pour Point,
Flash Point,
kg/l at 15.6°C,
40°C100°C °C, ASTM D97
°C, ASTM D92
ASTM D1298
Mobil Pyrogard 53 41.8 5.1 41 Visit mobil.ca /pds for the most current product information
0
246 1.155
Click Here to return to PRODUCT APPLICATION INDEX
METALWORKING FLUIDS
Mobilmet™ 420 Series products are high performance
multi-purpose cutting oils. They are chlorine-free,
non-staining and non-corrosive oils for ferrous and
non-ferrous metals. They are designed for light to
moderate duty cutting operations and are also suitable
Mobilmet 426 Mobilmet 427 Viscosity, ASTM D445 Spec. Gravity
cSt at
cSt at
Pour Point,
Flash Point,
kg/l at 15°C,
40°C100°C °C, ASTM D97
°C, ASTM D92
ASTM D4052
32 46 5.7 6.9 -12
-10
cSt at
40°C
Mobilmet 762 Mobilmet 763 Mobilmet 766 10.0 18.0 36.0 3.0 4.0 6.0 140 160 180
Product
Colour, ASTM
2.0 0.87 0.87 0.88 1.6
1.6
1.6
a small concentration of biocide to guard against
deterioration in storage. These properties make
Mobilcut 100 a versatile fluid well suited to many
machining applications.
Density EmulsionPour Point,
@ 15ºC (kg/L)
Stability
°C, ASTM D97
0.89 Sulfur,
Active
Excellent -6
MARINE
Mobilcut™ 100 is a soluble cutting and cooling fluid
suitable for a number of machining and grinding operations. Select mineral oil base stocks are blended with
an additive system that includes a highly effective and
stable emulsifier, a potent rust protection package and
Mobilcut 100
control of built-up edge. Their light color enables the
work area to be seen at all times. Closer tolerances
are consistently achieved. These oils are formulated
to prevent the formation of oil mist in the vicinity of the
machine tool, contributing to a safer, more pleasant,
work environment.
Kinematic Viscosity Spec. Gravity
cSt at
Flash Point,
kg/l at 15°C,
100°C
°C, COC, ASTM D92
ASTM D4052
Product
0.874
0.877
PASSENGER
Mobilmet™ 760 Series high performance oil based
cutting oils are chlorine-free and intended for severe
cutting operations, especially on difficult-to-machine
steels. The active cutting oil technology is corrosive to
copper and its alloys. In comparison with other leading
premium cutting oils, these oils have demonstrated
outstanding surface finish, extended tool life and
194 198 COMMERCIAL
Product
as machine tool lubricants and for use in light duty
hydraulic systems. These oils are light in colour and
transparent so the work area can be seen at all times.
Mobilmet 420 Series oils are formulated to prevent the
formation of oil mist in the vicinity of the machine tool.
INDUSTRIAL
INDUSTRIAL LUBRICANTS
Viscosity, ASTM D445
cSt at 40°C
35
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
42
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
METALWORKING FLUIDS
Mobilcut™ 140 is a long-life, biostable, chlorine-free
high performance metalworking fluid. When mixed with
water the emulsion formed has a milky appearance.
Product
Appearance
Mobilcut 140
Amber Liquid
Spec. Gravity
kg/l at 20°C, ASTM D4052 Emulsion Type
0.95
Milky
Mobilcut™ 350 is a fully biostable, mineral oil-free
synthetic metalworking fluid. It is specially formulated
for grinding and general cutting operations of ferrous
materials. Mobilcut 350 is a carefully balanced product
Product
Appearance
Mobilcut 350
Amber Liquid
1.10
Product
Formesso Summer Grade
pH at
3% Emulsion
Corrosion Test
(IP 287) Breakpoint %
Refractometer
Correction Factor
9.1
3.0
1.0
designed to provide excellent machining performance,
long charge life and excellent tramp oil rejection properties. Mobilcut 350 is a universal product that meets
the exacting demands of modern machine shops.
Spec. Gravity
kg/l at 15°C, ASTM D4052 Emulsion Type
Formesso™ Summer Grade is a high quality metalforming fluid primarily recommended for bolt forming
and general purpose machining, and automatic
machine tools processing free machining steels in
light to moderate applications. This fluid provides
anti-wear and lubricity properties, resistance to
Mobilcut 140 is formulated with high levels of lubricity
additives to provide excellent performance in arduous
machining operations.
Clear Solution
pH at
3% Emulsion
Corrosion Test
(IP 287) Breakpoint %
Refractometer
Correction Factor
9.1
3.0
1.9
foaming and oxidation and corrosion protection. It
also contains an oiliness agent and minimizes smoke
formation during the bolt-forming and threading operations. Being non-corrosive, Formesso Summer Grade
fluid is particularly suitable for the machining of copper
and its alloys.
Spec. Gravity
kg/l at 15°C, ASTM D4052 Flash Point
°C, ASTM D92
Pour Point
°C, ASTM D97
0.880
250
-15
43 Visit mobil.ca /pds for the most current product information
Viscosity, ASTM D445
cSt at 40°C
185
Click Here to return to PRODUCT APPLICATION INDEX
MIST OILS
Product
Mobilgear MS 100 Mobilgear MS 320 Mobilgear MS 460
The products have enhanced surface wetting capabilities and they reclassify (or agglomerate) readily from a
mist to a liquid when the mist is subjected to extreme
turbulence or is impinged onto a surface at high velocity. This allows a lubricating film to form on bearings and
gears and prevents stray mist from escaping through
narrow apertures into the atmosphere.
Viscosity, ASTM D445 FZG Scuffing,
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point, °C, ASTM D97 Flash Point,
°C, ASTM D92
100 320
460
11.2 25
31.5
95 100
100
-12 -9
-6
234
230
238
DIN 51534
A/8.3/90, Fail Stage
12+ 12+
12+
COMMERCIAL
Mobilgear™ MS Series (formerly Mobil Mist Lube) are
high performance oils designed for the oil-fog or mist
lubrication of machine components such as slideways,
bearings, gears, chains etc. They are formulated from
high quality, solvent refined base stocks and a unique
additive system designed for optimum reclassifying
properties. They have a high resistance to oxidation
and good extreme pressure and anti-wear properties.
INDUSTRIAL
INDUSTRIAL LUBRICANTS
PASSENGER
MARINE
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
44
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
OTHER INDUSTRIAL OILS
Canthus™ 680 is a high viscosity straight mineral oil
for economical lubrication of heavy industrial machinery.
It is primarily recommended for heavy slow-moving
components of enclosed gear units and circulation
systems requiring an uncompounded oil of high viscosity. This oil has excellent demulsibility and good natural
Product
ISO VG
Canthus 680
680
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
694
36.9
83
-9
280
Faxam™ paraffinic process oils are manufactured to
ISO-grade viscosity limits with lower pour points for
improved low temperature performance. They are well
suited to a wide range of industrial and process oil applications and can be used as lubricants in non-critical
circulating oil and hydraulic systems where bulk oil
temperatures are moderate and operating pressures
low enough that anti-wear/extreme pressure additives
are not required. These oils are an economic choice
Product
ISO VG
Faxam 22E
Faxam 32
22
32
Mobil Sawguide Oil 68
Mobil Sawguide Oil 100
Mobil Sawguide Oil 150
68
100
150
where high leakage cannot be avoided. As process
oils, their physical characteristics make them suitable
as a diluent oil or carrier in the manufacture of such
products as lubricating oil additives, paper defoamants,
seals, carbon paper and other chemical formulations.
Faxam oils can also be used for leather tanning,
as fluids for mineral oil seals, autoclaves and dust
suppression, or as lubricant-blending bases or glass
mould release agents.
Viscosity, ASTM D445
cSt at 40°C
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Colour,
ASTM
22
32
-36
-15
205
217
1.0
0.5
Mobil™ Sawguide Oils are designed to lubricate
the thin blades of modern gang saws and edgers.
They exhibit excellent anti-wear and extreme pressure
properties and cling tenaciously to blade and guide
surfaces, promoting extended blade life and reduced
oil consumption. These oils control pitch and resin
build-up on blades and sawguides, resulting in lower
Product
ISO VG
oxidation stability. As an uncompounded steam cylinder
oil, Canthus 680 separates readily from condensate
and is suitable for use with dry steam or where water
washing off cylinder walls is not detrimental to lubrication. It can also be employed as a heat transfer oil,
tempering oil and forging compound.
friction and wear and increased cutting efficiency.
Potent rust and corrosion inhibitors help protect blade
surfaces from rust that can stain lumber. Tackiness
additives help reduce the oil thrown off or blown off by
air/water sprays. Most importantly, a friction reducing
film reduces cooling water requirements, promoting
drier sawdust.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
68
91
150
9.6
11.5
16.2
-30
-24
-15
215
225
225
45 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
OTHER INDUSTRIAL OILS
Viscosity, ASTM D445 Product
ISO VG
Mobil Synthetic Oven Lube 1090 synthetic ester base fluid plus very effective anti-wear
additives. It does not contain silicone. Compared to
mineral oil and conventional chain lubricants, Mobil
Synthetic Oven Lube 1090 reduces carbon build-up
and extends cleaning intervals.
cSt at
40°C
220 cSt at
100°C
Viscosity Index
210 22 Mobil Synturion™ 6 is a premium quality synthetic
base fluid specially formulated to meet the demanding
lubrication and cooling requirements of mechanical
seals – and to maximize seal life. The outstanding
Mobil Synturion 6 126 inherent properties of the synthetic base oil, enhanced
by a proprietary additive package, are ideally suited
to the demanding requirements of mechanical seal
operation. Meets NSF H1 (USA) for food industries.
Viscosity, ASTM D445 Spec. Gravity,
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point, °C, ASTM D97 Flash Point,
°C, ASTM D92
5.2 1.89 135 -63
168
Mobil™ System Cleaner is an oil-soluble, solvent-free
cleaner fortified with emulsifiers, dispersants, and
rust inhibitors. A 5% concentration in the system oil
is typically recommended. Mobil System Cleaner is
safe for all ferrous and non-ferrous metals used in
Slurry Oil 62 is a conditioning oil used in the manufacture of various types of explosives made with ammonium nitrate. This product has a low viscosity for optimal
kg/l at 15ºC,
ASTM D4052
0.799
280.4 (138) Spec. Gravity,
kg/l at 15ºC,
ASTM D4052
0.926
MARINE
55 industrial equipment and is compatible with all seals
with up to 20% maximum concentration in the oil. The
viscosity and high flash point of Mobil System Cleaner
enable equipment to be operated normally during the
cleaning process.
Viscosity, ASTM D445
cSt at
Flash Point,
Product40°C
°C, ASTM D92 Mobil System Cleaner 240
PASSENGER
Product
Flash Point,
°C, ASTM D92
COMMERCIAL
Mobil™ Synthetic Oven Lube 1090 is a high performance synthetic high temperature lubricant designed
specifically for lubrication of hot conveyor chains in
drying ovens and similar severe applications. This
formulation combines a carefully balanced blend of
high-molecular-weight synthetic hydrocarbons and
INDUSTRIAL
INDUSTRIAL LUBRICANTS
hydrocarbon loading and a low pour point for all-season
use. The low temperature properties also facilitate
handling and transfer at low ambient temperatures.
Viscosity, ASTM D445
cSt at
Pour Point,
Flash Point,
Product40°C
°C, ASTM D97 °C, ASTM D92
10.1
160
Click Here to return to PRODUCT APPLICATION INDEX
46
GREASES
Visit mobil.ca /pds for the most current product information
-45
AVIATION
Slurry Oil 62
INDUSTRIAL LUBRICANTS
PAPER MACHINE OILS
Mobil SHC™ PM Series high performance synthetic
lubricants are specifically designed for some of the
most demanding industrial paper machine circulating
systems. They deliver exceptional lubrication characteristics not attainable with conventional premium
mineral-oil based fluids. These oils provide maximum
protection for gears and bearings operating under
some of the most severe conditions. Their very low
pour points and naturally high viscosity index (VI)
Product
ISO VG
Mobil SHC PM 220 Mobil SHC PM 320 220 320 Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
225 325 25.6 34.7 Mobil DTE™ PM Series oils are specifically designed
for demanding industrial paper machine circulating
systems. They are engineered to provide exceptional
lubrication qualities while protecting system components from rust and corrosion. This is particularly
important in the wet-end where water and chemical
contaminants can enter the lubrication system. They
Product
ISO VG
Mobil DTE PM 150 Mobil DTE PM 220 Mobil DTE PM 320 150 220 320 help ensure good low temperature performance
and startup while maintaining excellent viscosity
characteristics at very high temperatures. The fluids
are very shear-stable and maintain viscosity control
even when subjected to severe mechanical shear
in heavily loaded bearings and gears. Their low traction
coefficient and high viscosity index promote lower
energy consumption and reduced component operating temperatures.
V.I.
Spec. Gravity
ASTM D2270,
Pour Point,
Flash Point,
kg/l at 15.6°C,
typical
°C, ASTM D97
°C, ASTM D92
ASTM D1298
127 130 -36 -33
220
220
0.863
0.865
exhibit good viscosity characteristics, allowing reduced
startup to production times while maintaining excellent
viscosity characteristics at high temperatures. They
provide excellent resistance to oxidation and thermal
degradation, exceptional protection against rust and
corrosion, and a high level of anti-wear performance.
Viscosity, ASTM D445 Spec. Gravity
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
kg/l at 15.6°C,
ASTM D1298
150 220 320 14.7 19.0 25.4 95 min
95 min
95 min
-6 -6
-6
250 260 250
0.888
0.889
0.892
47 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
PNEUMATIC TOOL OILS
to absorb moisture from the wet mine air system,
while maintaining a protective film on drill components.
Potent EP characteristics help protect components
subjected to percussive contact for improved drill life in
heavily loaded equipment. The high viscosity indexes
and low pour points help ensure effective lubrication
at high and low operating temperatures.
Viscosity, ASTM D445
cSt at
cSt at
Pour Point,
Flash Point,
Product
ISO VG
40°C
100°C
°C, ASTM D97
°C, ASTM D92
Mobil Arox EP 22
Mobil Arox EP 32
Mobil Arox EP 68 Mobil Arox EP 100
Mobil Arox EP 150
Mobil Arox EP 220
22
32
68
100
150
220
22
32
68
100
150
220
4.2
5.6
9.1
11.9
15
19.5
-45
-33
-33
-21
-15
-21
168
219
239
252
268
288
COMMERCIAL
Mobil Arox™ EP Series high performance rock drill
oils are designed primarily for pneumatically operated
rock drills in underground and surface mining operations. High quality base stocks and carefully selected
additives combine to deliver excellent chemical stability
and outstanding protection against wear and corrosion. These oils provide an optimum balance between
adhesiveness and emulsibility. This allows the lubricant
INDUSTRIAL
INDUSTRIAL LUBRICANTS
PASSENGER
INDUSTRIAL LUBRICANTS
QUENCH OILS
Product
Mobil Fenso 90
Mobil Fenso 150
speed control, as well as excellent and consistent
cleanliness of parts. FENSO 150 is a high speed
cold quench oil recommended for carbon and alloy
steels requiring uniform hardness, cleanliness and
dimensional stability.
MARINE
Mobil Fenso™ Series quench oils promote excellent
long life performance in cold quenching operations.
FENSO 90 is a premium high speed product, formulated with a highly effective accelerator concentrate to
help provide long service life with dependable quench
Viscosity, ASTM D445
IVF Quench Test
cSt at
cSt at
Pour Point,
Max cooling rate
40°C100°C
°C, ASTM D97
°C/min (@°C)
38
25.1
6.5
4.7
200
205
637
634
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
48
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
REFRIGERATION OILS
Please contact your local sales rep or our technical help desk
at 1-888-968-3776 for any inquiries about your application.
Mobil Glygoyle™ 22 is a high performance synthetic
lubricant that delivers outstanding performance in gear,
bearing and circulation system applications operating
at extreme temperatures in conditions well beyond
the capabilities of mineral oils. This polyalkylene
glycol-based (PAG) lubricant is shear-stable with outstanding resistance to thermal degradation, oxidation
Product
Mobil Gylgoyle 22
Viscosity, ASTM D445
cSt at
cSt at
Pour Point,
Flash Point,
40°C100°C
°C, ASTM D97
°C, ASTM D92
177
25.1
-41
Mobil Gargoyle™ Arctic Oils have very low pour
points for lubricating cylinders and bearings of
reciprocating and rotary refrigeration compressors.
These naphthenic oils are almost wax-free, delivering
Product
ISO VG
Mobil Gargoyle Arctic C Heavy
Mobil Gargoyle Arctic Oil 300
46
68
Product
ISO VG
68
220
Mobil Zerice S 68
68
229
Viscosity, ASTM D445 cSt at 40°C
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
46
68
-39
-36
195
200
rotary compressors and are particularly successful in
systems using ammonia as the refrigerant. These fluids
are compatible with most common refrigerants, except
sulphur dioxide.
Viscosity, ASTM D2270
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
69
220
10.1
25
136
149
-50
-39
266
260
Mobil Zerice™ S Oils are premium quality synthetic
refrigeration compressor lubricants based on alkyl
benzenes, which have outstanding miscibility with
hydrochlorofluorocarbon (R22). This allows them
to be used in very low temperatures, down to -60°C.
Their very low pour and flow points help prevent
harmful wax precipitation, which can block expansion
Product
ISO VG
excellent fluidity at very low temperatures. They are
used primarily with ammonia refrigerants but are
suitable for many other refrigerant types; exceptions
include all HFC refrigerants and sulphur dioxide.
Mobil Gargoyle Arctic SHC™ 200 Series are synthetic hydrocarbon polyalphaolefin (PAO) lubricants for
refrigeration compressors and heat pumps in severe
service. They are recommended for reciprocating and
Mobil Gargoyle Arctic SHC 226E
Mobil Gargoyle Arctic SHC 230
and the formation of sludge and deposits. A proprietary
additive system strengthens EP/anti-wear protection,
guards against corrosion and rust and resists foam
without detracting from the intrinsic attributes of the
PAG base oils. It is suitable for specific refrigeration
applications, such as propane and butane screw and
centrifugal compressors.
valves and heat transfer surfaces. The synthetic
formulation provides excellent chemical stability,
which resists reaction with refrigerants and maintains
high thermal stability to help prevent oil breakdown.
In some circumstances, these oils can also be
used in compressors where ammonia acts as the
refrigerating fluid.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
68
6.5
-27
174
49 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
RUST PREVENTIVE
finely finished parts between machining operations,
including those where water-soluble cutting and grinding fluids have been used. It is also suitable for use
on parts just before they are packaged for storage or
shipment, or to “dry” parts as temporary protection until
a heavier rust preventive can be applied.
Viscosity, ASTM D445
cSt at
Flash Point,
Product40°C
°C, ASTM D92
Mobilarma 245 2.6 38
Product
Mobilarma 778 Mobilarma 798 dustrial, construction, mining and marine applications.
Mobilarma 700 Series products exhibit excellent water
displacing properties and form thin tenacious films
that protect surfaces even under severe conditions,
including high moisture levels and exposure to acid or
corrosive fumes.
Viscosity, ASTM D445
Spec. Gravity
cSt at
cSt at
40°C100°C
39 –
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
-3
–
190 238
–
23.1 Product
Mobil Vaprotec Light 0.880
–
inhibitor to protect surfaces submerged in oil, and
vapour space inhibitors to protect surfaces exposed to
oil vapours.
MARINE
Mobil Vaprotec™ Light is an ISO 32, turbine-quality
circulation oil containing anti-oxidants and defoamants.
It is enhanced with a three-phase rust inhibitor to
protect surfaces lightly coated with oil, a liquid phase
kg/l at 15.6°C,
ASTM D1298
Viscosity, ASTM D445 Spec. Gravity cSt at
cSt at
Pour Point, Flash Point,
kg/l at 15.6°C,
40°C100°C V.I.°C, ASTM D97 °C, ASTM D92 ASTM D1298
30 5.3 95 PASSENGER
Mobilarma™ 700 Series premium performance rust
preventives cover a range of applications, including
storage and inter-operational activities. Mobilarma 778
is designed for the protection of cold-rolled sheet and
coiled steel in the metal industry. Mobilarma 798 is for
the lubrication and rust protection of wire rope in in-
COMMERCIAL
Mobilarma™ 245 rust preventive is designed to protect
metal surfaces from rust and corrosion. It is formulated
using light bodied petroleum solvents with polar rust
preventive, water displacement and fingerprint neutralizing additives. This product is easy to apply and easy
to remove, making its use less manpower intensive.
Mobilarma 245 is suited for the thin film protection of
INDUSTRIAL
INDUSTRIAL LUBRICANTS
-7
193 min
0.875
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
50
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
SPINDLE OILS
Mobil Velocite™ Oil Numbered Series are premium
performance products primarily designed for the
lubrication of high speed spindles in machine tools.
They are also used in some critical hydraulic, circulation systems and air line oilers where the appropriate
viscosity grade is selected. They are formulated from
select high quality, low viscosity base oils and additives
that deliver good resistance to oxidation and protection
from rust and corrosion. They possess very good resistance to foaming and separate readily from water.
Viscosity, ASTM D445 Product
ISO VG
cSt at
40°C
cSt at
100°C
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Mobil Velocite No 6 Mobil Velocite No 10 10.0 22.0 2.62 4.0 -15
-30
180
212
10 22 INDUSTRIAL LUBRICANTS
TRANSFORMER OILS
Voltesso™ is a premium line of electrical insulating oils
designed to meet the critical operating requirements of
most types of electrical equipment. They are made from
fully refined, naphthenic base stocks and have excellent
dielectric strength and power-factor characteristics and
are formulated to resist oxidation and sludge. Voltesso
oils have outstanding low temperature flow characteris
Product
Voltesso N36
Voltesso 35
tics that help improve oil circulation and heat transfer in
electrical equipment operating under the most severe
cold weather conditions. They are recommended for
use in power transformers, especially those that have
forced oil cooling or are subject to cold startup. They
meet Canadian Standards Association C50-08 specifications for Class A, Type I and Type II oils respectively.
Viscosity, ASTM D445
cSt at
cSt at
Pour Point,
Flash Point,
40°C100°C °C, ASTM D97
°C, COC, ASTM D92 7.6
7.6
2.1
2.1
51 Visit mobil.ca /pds for the most current product information
-46 max
-46 max
145 min
145 min
Click Here to return to PRODUCT APPLICATION INDEX
TURBINE OILS
Product
ISO VG
Mobil SHC 824 Mobil SHC 825 32 46 Viscosity, ASTM D445
Spec. Gravity
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
kg/l at 15.6°C,
ASTM D4052
31.5 43.9 5.9 7.9 135 145 <-54 -45 248 248 0.83
0.83
Mobil DTE 932 GT 32 Viscosity, ASTM D445
Spec. Gravity
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
kg/l at 15.6°C,
ASTM D4052
31.5 6.1 141 -18 240 0.84
Mobil DTE 832 Mobil DTE 846 32 46 engineered to provide the deposit control and “keep
clean” performance required by severe duty gas
turbines as well as excellent water separability needed
for steam turbine operation. The formulations also
include a non-zinc anti-wear system to meet the
load-carrying requirements of geared turbines.
MARINE
Mobil DTE™ 800 Series high performance turbine oils
are designed for use in steam turbines, gas turbines
and combined cycle gas turbine (CCGT) applications
under some of the most severe operating conditions.
These progressive products are based on high quality
hydrotreated basestocks for exceptional thermal/oxidation resistance along with specially chosen additives
Product
ISO VG
additive system to provide long oil life in combination
with industry leading “keep clean” performance. The formulation also includes a non-zinc anti-wear system to
meet the load-carrying requirements of geared turbines.
PASSENGER
Mobil DTE™ 932 GT is a next generation high performance turbine oil designed for use in GE large frame
gas turbines. This product is based on selected high
quality base oils carefully balanced with a proprietary
Product
ISO VG
and a unique additive system. This formula provides
outstanding low temperature fluiditiy and exceptional
resistance to degradation at high temperatures well
beyond the capabilities of premium quality mineral oils.
Mobil SHC 800 Series lubricants also provide excellent
anti-wear properties as well as protection against rust
and corrosion plus good air release performance and
resistance to foaming.
COMMERCIAL
Mobil SHC™ 800 Series turbine oils are designed
specifically to meet the needs some of the most severe
industrial gas turbine applications with a nominal
10,000 hour TOST life. They are recommended for
the lubrication of land-based gas turbines, particularly
units under 3,000 hp used as standby power units,
and in some types of total energy and combined cycle
(gas/steam) systems. This innovative product family
is formulated from wax-free synthesized hydrocarbons
INDUSTRIAL
INDUSTRIAL LUBRICANTS
Viscosity, ASTM D445
Spec. Gravity
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
kg/l at 15.6°C,
ASTM D4052
29.6 42.4 5.4 6.2 110 106 -30 -30
224
244 0.86
0.87
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
52
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
TURBINE OILS
Mobil DTE™ 724 Oil was developed for higher-output
gas turbines such as the General Electric Heavy Duty
Gas Turbine Frame 7000. Mobil DTE 724 Oil offers
Product
ISO VG
Mobil DTE 724 32 Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
31 5.4 95 10 420 Mobil DTE™ 732 M is next generation high performance turbine oil designed for use in Mitsubishi
Heavy Industry (MHI) non-geared Single Shaft Heavy
Duty Gas & Steam Turbines and Multi Shaft Gas
Turbines. This product meets MHI’s requirements
Product
ISO VG
Mobil DTE 732 M 32 Mobil DTE 732 Mobil DTE 746 32 46 for long life – high temperature turbine applications,
MS04-MA-CL005, through high quality base oils
and additive system designed to provide long oil life.
Mobil DTE 732 M also meets the requirements of
MS04-MA-CL001 and CL002.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
31.3 5.8 131 -15 Mobil DTE™ 700 Series lubricants are the most recent
addition to the Mobil DTE turbine lubricant family,
long recognized for high quality and reliability. These
zinc-free lubricants are specifically designed for gas
and steam turbine applications. They are formulated
with carefully selected base stocks and additives,
including anti-oxidants, rust and corrosion inhibitors
Product
ISO VG
excellent thermal and oxidative stability, and resistance
to deposit formation to meet the high temperature
demands of gas turbines.
Flash Point,
°C, ASTM D92
233
and anti-foam agents. These deliver outstanding
resistance to oxidation and chemical degradation.
Mobil DTE 700 lubricants exhibit excellent water
separation, resistance to emulsion formation and
anti-foaming characteristics to provide reliable operation. Their enhanced air release properties are critical
for turbine hydraulic control mechanisms.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
30 44 5.5 6.8 117 113 -30 -30
228
230
53 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
TURBINE OILS
Viscosity, ASTM D445
Product
cSt at
cSt at
40°C100°C
Mobil Teresso 32
Mobil Teresso 46
Mobil Teresso 68
32
46
68
sludge formation tendency specifications required by
many utilities, in addition to passing oxidation tests.
Mobil Teresso oils offer excellent demulsibility, rust
inhibition and foam control. They are also recommended
for use in circulating bath, splash and ring oiled systems
supplying lubricant for bearings and gears of industrial
machinery. They can also be used in hydraulic systems
where anti-wear oil is not required.
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Density
@ 15°C (kg/L)
-32
-27
-26
204
212
226
0.868
0.873
0.876
5.13
6.36
8.26
Product
Mobil Teresso GTC 32
Mobil Teresso GTC 46
High quality hydrotreated basestocks combine with
a proprietary additive package to work synergistically,
providing exceptional trouble-free long-life performance
in severe cyclical service gas turbines.
Viscosity, ASTM D445
cSt at
40°C
V.I.
ASTM D2270
Pour Point, °C, ASTM D97 Flash Point,
°C, COC, ASTM D92
32
46
118
116
-27
-24
215 min
215 min
PASSENGER
Mobil Teresso™ GTC Series. These high performance
turbine oils deliver excellent lubrication for turbines
in the most severe operating conditions. These highly
versatile lubricants can be used in steam, gas, and
combined cycle gas turbine (CCGT) applications.
COMMERCIAL
Mobil Teresso™ is a line of premium turbine-quality
R&O (Rust & Oxidation) circulating oils designed
primarily for steam and hydraulic turbine circulating
systems. All grades are formulated from select API
Group 1 basestocks and a high performance additive
system that provides outstanding oxidation control,
rapid separation of foam and air and protection from
rust and corrosion. These oils easily surpass the
INDUSTRIAL
INDUSTRIAL LUBRICANTS
MARINE
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
54
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS
WAY OILS
Mobil Vactra™ Oil Numbered Series are premiumquality slideway lubricants specifically designed to
meet the requirements for accuracy, aqueous coolant
Product
ISO VG
Mobil Vactra No. 2 Mobil Vactra No. 4 Viscosity, ASTM D445
68 220 cSt at 40°C
Pour Point,
°C, ASTM D97
68 221 -33 -3
Mobil Vacuoline™ 1400 Series are high performance
lubricants specifically designed to satisfy the requirements of machine tools that use a single oil for both
hydraulics and way lubrication. They are formulated
using high quality mineral base oils and a unique additive system that provides excellent lubricity to eliminate
stick-slip and chatter of heavily loaded and vertical
Product
ISO VG
Mobil Vacuoline 1405 Mobil Vacuoline 1409 Mobil Vacuoline 1419 32 68 220 separability, and equipment protection of precision
machine tools.
Flash Point,
°C, ASTM D92
228
240
box ways. They exhibit a high degree of oxidation and
thermal stability that helps to extend oil life and keep
lubricated surfaces clean and free from corrosion or
deposits that could detract from finished parts quality
and accuracy. These oils provide the optimum balance
between these divergent requirements.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
32 68 215 5.3 8.57 19.0 96 96 96 -12 max -6 max
-6 max
210
218
257
55 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
COMMERCIAL VEHICLE LUBRICANTS
PRODUCT
PAGE
Mobil Delvac™ Synthetic Transmission Fluid 50.......... 63
Mobil Delvac™ Synthetic ATF....................................... 63
Mobil Delvac™ Synthetic Gear Oils.............................. 63
Mobil Delvac™ Synthetic Final Drive and Axle Oil........ 63
Mobilube™ HD LS 80W-90.......................................... 66
Mobilube™ HD Plus MG 75W,
80W-90 and 85W-140................................................... 66
Mobilube™ HD Extra MG 75W and 80W-140.............. 66
Mobilube™ XFD 50 and 60.......................................... 66
Mobiltrans™ AST (All-Season Transmission)............... 67
Mobiltrans™ AST 30 and
Mobiltrans™ AST Extra 20........................................... 67
Mobiltrans™ HD 10W, 30 and 50................................. 67
Tractor Hydraulic Fluids
Mobil Hydraul™............................................................ 68
Railway
Galcar All Year.............................................................. 68
Coolant/Antifreeze
Mobil Delvac™ Extended Life
Coolant/Antifreeze – C Series...................................... 69
Mobil™ Heavy Duty SCA
Precharged Coolant/Antifreeze..................................... 69
Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
56
GREASES
Heavy Duty Power Transmission Fluids
AVIATION
Mobil Delvac™ CNG/LNG 15W-40............................... 62
Mobil GEO™ 15W-40................................................... 62
MARINE
Heavy Duty Natural Gas Engine Oils
PASSENGER
HDEO Selection Chart.............................................57-58
Multigrade HDEO Selection Star Chart........................ 59
Mobil Delvac 1™ ESP 5W-40 and 0W-40.................... 60
Mobil Delvac 1™ LE 5W-30.......................................... 60
Mobil Delvac™ Elite 222 0W-30................................... 60
Mobil Delvac™ Elite 10W-30 and 15W-40.................... 60
Mobil Delvac™ 1300 Super 10W-30 and F2 15W-40.... 61
Mobil Delvac™ 1230 and 1240...................................... 61
Mobil Delvac™ 1640..................................................... 61
DIOL™ 9 RD Series..................................................... 62
COMMERCIAL
Heavy Duty Diesel Engine Oils
INDUSTRIAL
COMMERCIAL VEHICLE PRODUCT LISTING BY APPLICATION
COMMERCIAL VEHICLE LUBRICANTS
HEAVY DUTY ENGINE OILS SELECTION CHART
Viscosity Grade
API CF
API CF-2
API CG-4
API CH-4
API CI-4
API CI-4 PLUS
API CJ-4
API SF
API SH
API SJ
API SL
API SM
API SN
ACEA E2
ACEA E5
ACEA E6
ACEA E7
ACEA E9
JASO DH-1
JASO DH-2
CATERPILLAR ECF-2
CATERPILLAR ECF-3
CATERPILLAR TO-2
CUMMINS CES 20071
CUMMINS CES 20072
CUMMINS CES 20076
CUMMINS CES 20077
CUMMINS CES 20078
CUMMINS CES 20081
DAF EXTENDED DRAIN
FORD WSS-M2C171-E
Twin Disc S364A
DETROIT FLUID SPEC 7SE 270
DETROIT FLUID SPEC 93K214
DETROIT FLUID SPEC 93K218
DETROIT ENGINE OIL 93K218
DEUTZ DQC III-10 LA
DEUTZ DQC IV-10 LA
EMD ENGINES
GE
MACK EO-M
MACK EO-M Plus
MACK EO-N Premium Plus 03
MACK EO-O Premium Plus
MAN M 270
MAN M 3275-1
MAN M 3277
MAN M 3477
MAN M 3677
MB-APPROVAL 228.2
MB-APPROVAL 228.3
MB-APPROVAL 228.31
MB-APPROVAL 228.51
MB-APPROVAL 235.27
MTU OIL CATEGORY 2
MTU OIL CATEGORY 2.1
MTU OIL CATEGORY 3.1
RENAULT TRUCK RGD
RENAULT TRUCK RLD-2
RENAULT TRUCK RLD-3
RENAULT TRUCK RXD
VICKERS 35VQ25
VOLVO VDS-2
VOLVO VDS-3
VOLVO VDS-4
ZF TE-ML04B
ZF TE-ML04C
Mobil Delvac 1 ESP
5W-40
0W-40
–
–
–
–
R
–
R
R
R
R
R
R
R
R
–
–
–
–
–
–
R
–
R
R
–
–
–
–
–
–
–
–
R
–
R
–
–
–
–
–
R
–
R
R
–
–
–
–
–
–
–
R
–
–
–
–
R
R
–
–
–
–
R
–
–
–
R
–
R
–
–
–
R
–
–
–
–
–
–
–
–
–
–
–
R
R
R
–
–
–
–
–
R
–
–
–
–
–
–
–
–
–
R
–
–
–
R
–
–
–
R
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
R
–
R
–
–
–
–
–
Mobil Delvac 1 LE
5W-30
–
–
–
–
R
R
R
–
–
–
–
–
R
–
–
R
R
R
–
R
–
R
–
–
–
–
–
–
R
R
R
–
–
–
R
–
–
R
–
–
–
–
–
R
–
–
–
R
R
–
–
R
R
–
–
–
R
–
R
R
–
–
–
R
R
–
–
Mobil Delvac Elite 222
0W-30
–
–
–
R
R
R
R
–
R
R
R
R
–
–
–
–
–
–
–
–
–
R
–
–
–
R
–
–
R
–
–
–
–
–
–
–
–
–
–
–
–
R
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Mobil Delvac Elite
10W-30
15W-40
–
–
–
–
–
–
R
R
R
R
R
R
R
R
–
–
–
–
–
–
–
R
–
R
–
–
–
–
–
–
–
–
R
R
R
–
–
–
–
–
–
R
R
R
–
–
–
–
–
–
–
–
–
–
–
–
R
R
–
–
–
–
–
–
–
–
–
R
–
–
R
R
–
–
–
–
–
–
–
–
–
–
–
–
–
–
R
R
–
–
–
–
–
–
–
–
–
–
–
–
–
–
R
R
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
R
R
R
R
–
–
–
–
Mobil Delvac 1300 Super
10W-30
F2 15W-40
R
R
–
R
–
–
R
R
R
R
R
R
R
R
–
–
–
–
–
–
R
R
R
R
–
–
–
–
–
–
–
–
–
–
R
R
–
–
–
–
–
–
R
R
–
–
–
–
–
–
–
–
–
–
–
–
R
R
–
–
–
–
–
–
–
–
–
–
–
R
–
–
–
–
–
–
–
–
–
–
–
–
–
–
R
–
R
R
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
R
–
–
–
–
–
–
–
R
–
–
–
–
–
–
R
–
–
–
–
–
R
R
R
R
R
R
–
–
–
–
HEAVY DUTY ENGINE OILS SELECTION CHART
R
R
–
–
–
–
–
R
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
R
–
–
–
–
–
–
R
–
–
–
–
–
R
–
–
–
–
R
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
R
–
–
–
–
R
–
–
–
–
R
–
–
–
–
–
–
–
–
–
–
R
–
GREASES
R
R
–
–
–
–
–
R
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
DIOL 9 RD
40
20W-40
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
R
R
R
R
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
AVIATION
Mobil Delvac 1640
MARINE
Mobil Delvac 1240
PASSENGER
Mobil Delvac 1230
COMMERCIAL
Viscosity Grade
API CF
API CF-2
API CG-4
API CH-4
API CI-4
API CI-4 PLUS
API CJ-4
API SF
API SH
API SJ
API SL
API SM
API SN
ACEA E2
ACEA E5
ACEA E6
ACEA E7
ACEA E9
JASO DH-1
JASO DH-2
CATERPILLAR ECF-2
CATERPILLAR ECF-3
CATERPILLAR TO-2
CUMMINS CES 20071
CUMMINS CES 20072
CUMMINS CES 20076
CUMMINS CES 20077
CUMMINS CES 20078
CUMMINS CES 20081
DAF EXTENDED DRAIN
FORD WSS-M2C171-E
Twin Disc S364A
DETROIT FLUID SPEC 7SE 270
DETROIT FLUID SPEC 93K214
DETROIT FLUID SPEC 93K218
DETROIT ENGINE OIL 93K218
DEUTZ DQC III-10 LA
DEUTZ DQC IV-10 LA
EMD ENGINES
GE
MACK EO-M
MACK EO-M Plus
MACK EO-N Premium Plus 03
MACK EO-O Premium Plus
MAN M 270
MAN M 3275-1
MAN M 3277
MAN M 3477
MAN M 3677
MB-APPROVAL 228.2
MB-APPROVAL 228.3
MB-APPROVAL 228.31
MB-APPROVAL 228.51
MB-APPROVAL 235.27
MTU OIL CATEGORY 2
MTU OIL CATEGORY 2.1
MTU OIL CATEGORY 3.1
RENAULT TRUCK RGD
RENAULT TRUCK RLD-2
RENAULT TRUCK RLD-3
RENAULT TRUCK RXD
VICKERS 35VQ25
VOLVO VDS-2
VOLVO VDS-3
VOLVO VDS-4
ZF TE-ML04B
ZF TE-ML04C
INDUSTRIAL
COMMERCIAL VEHICLE LUBRICANTS
Mobil Delvac ™ Elite
Advanced synthetic blend with
exceptional resistance to sludge
Mobil Delvac
1300 Super
Premium conventional oil formulated
to meet or exceed original equipment
manufacturer (OEM) and API CJ-4
requirements, even in some of the
most extreme conditions
★★
★★
★★★
★★★
★★★
★★
★
★★
★★
★★★
COMMERCIAL VEHICLE LUBRICANTS
HEAVY DUTY DIESEL ENGINE OILS
★ The number of stars indicates relative performance level.
Multigrade Heavy Duty Engine Oils Selector Star Chart
Extended
Drain Capacity
59 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
HEAVY DUTY DIESEL ENGINE OILS
Product
Mobil Delvac 1 ESP 5W-40 Mobil Delvac 1 ESP 0W-40 Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Sulfated Ash,
wt%, ASTM D874
TBN, mg KOH/g,
ASTM D2896
Pour Point,
ºC, ASTM D97
98 87
14.7 15.2
156 186 1.0 1.0
8.7 7.7
-48
-48
Mobil Delvac 1 LE 5W-30 It is well suited for an extensive array of diesel-powered
commercial vehicles for both on- and off-highway use
in industries such as transportation, mining, construction and agriculture. Mobil Delvac 1 LE 5W-30 meets
or exceeds an extremely broad range of industry and
manufacturer specifications from around the world.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Sulfated Ash,
wt%, ASTM D874
TBN, mg KOH/g,
ASTM D2896
Pour Point,
ºC, ASTM D97
40
11.8 168 1 10 -51
Mobil Delvac Elite 222 0W-30 Viscosity, ASTM D445
cSt at
100°C
V.I.
ASTM D2270 Sulfated Ash,
wt%, ASTM D874
TBN, mg KOH/g,
ASTM D2896
Pour Point,
ºC, ASTM D97
69 12.2 176 1.0
7.7 -45 Diesel Particulate Filters (DPFs) and Diesel Oxidation
Catalysts (DOCs). These oils exhibit enhanced low
temperature fluidity, high temperature viscosity retention,
and piston deposit control and are highly recommended
by engine builders for use in all high performance diesel
engines in severe service, on and off highway.
AVIATION
Mobil Delvac Elite 10W-30 Mobil Delvac Elite 15W-40 with API CJ-4 additive technology, it is excellent for
light and heavy duty diesel engines, including those
with EGR and/or DPFs (Diesel Particulate Filters).
cSt at
40°C
Mobil Delvac™ Elite 10W-30 and 15W-40 are synthetic blend heavy duty diesel engine oils for extended
drain capability. They meet the API CJ-4 specification,
and provide the highest level of protection to modern,
high performance diesel engines with Exhaust Gas
Recirculation (EGR) and aftertreatment systems with
Product
MARINE
Mobil Delvac™ Elite 222 0W-30 synthetic, heavy duty
diesel engine oil helps extend engine life and improve
fuel economy in modern diesel engines. Formulated
Product
PASSENGER
Mobil Delvac 1™ LE 5W-30 synthetic, heavy duty
diesel engine oil provides advanced engine protection, and helps improve fuel economy in modern low
emissions vehicles. Mobil Delvac 1 LE 5W-30 utilizes
state-of-the-art technology to deliver exceptional
performance: engine durability, emissions system
protection and extended drain capability.
Product
Diesel Oxidation Catalysts (DOCs). It can also be
used in refrigeration units and older well-maintained
engines. Mobil Delvac 1 ESP 5W-40 and 0W-40 is
recommended for a wide range of heavy duty applications and operating environments found in the on-road
transport and off-road mining, forestry, construction,
and agricultural industries. It also meets the API SM
specification for gasoline engines.
COMMERCIAL
Mobil Delvac 1™ ESP 5W-40 and 0W-40 synthetic,
high performance, heavy duty diesel engine oil helps
extend engine life and may help improve fuel economy
in modern diesel engines operating in severe applications. This oil meets the API CJ-4 specification. Stateof-the-art technology delivers exceptional performance
in modern low emission engines, including those with
Exhaust Gas Recirculation (EGR) and aftertreatment
systems with Diesel Particulate Filters (DPFs) and
INDUSTRIAL
COMMERCIAL VEHICLE LUBRICANTS
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Sulfated Ash,
wt%, ASTM D874
TBN, mg KOH/g,
ASTM D2896
Pour Point,
ºC, ASTM D97
81 111 12.2 15.2 146 140
1.0 0.9
10.7 10.7
-36 -36 Click Here to return to PRODUCT APPLICATION INDEX
60
GREASES
Visit mobil.ca /pds for the most current product information
COMMERCIAL VEHICLE LUBRICANTS
HEAVY DUTY DIESEL ENGINE OILS
Mobil Delvac™ 1300 Super 10W-30 and F2 15W-40
high performance diesel engine oil helps extend engine life in some of the most severe on- and off-highway applications. It delivers outstanding performance
in modern high output, low emission engines including
those with Exhaust Gas Recirculation (EGR) and
aftertreatment systems with Diesel Particulate Filters
Product
Mobil Delvac 1300 Super 10W-30 Mobil Delvac 1300 Super F2 15W-40
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Sulfated Ash,
wt%, ASTM D874
TBN, mg KOH/g,
ASTM D2896
Pour Point,
ºC, ASTM D97
79 114 11.9 15.0 145 137 1.0 1.0 8.8 8.8 -47
-44 Mobil Delvac™ 1230 and 1240 are heavy duty, diesel
engine oils formulated from high performance base oils
and a balanced additive system of ashless dispersants,
metallic detergents, and inhibitors to control oxidation,
Product
Mobil Delvac Mobil Delvac 1640 wear, corrosion, and rust. They are used in a wide range
of applications where a monograde lubricant is recommended including 2-cycle diesel applications (e.g. the
Detroit Series 53, 71 and 92 two-cycle engines).
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Sulfated Ash,
wt%, ASTM D874
TBN, mg KOH/g,
ASTM D2896
Pour Point,
ºC, ASTM D97
108 12 100 0.80 5.8 -21
Mobil Delvac™ 1640 is a high performance monograde diesel engine oil formulated from advanced
technology base oils and a balanced additive system.
It is recommended for intercooled, turbocharged
Product
(DPFs) and Diesel Oxidation Catalysts (DOCs). Fully
backwards compatible, Mobil Delvac 1300 Super
10W-30 and F2 15W-40 delivers the same exceptional
performance in older conventional engines. As a result,
they meet or exceed the requirements of the API CJ-4,
CI-4 PLUS and CH-4 service categories as well as
those of Original Equipment Manufacturers (OEMs).
engines operating under severe conditions on and
off highway, and a range of applications calling for a
monograde lubricant.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Sulfated Ash,
wt%, ASTM D874
TBN, mg KOH/g,
ASTM D2896
Pour Point,
ºC, ASTM D97
132 14.7 112 1.4 12 -21
61 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
HEAVY DUTY DIESEL ENGINE OILS
DIOL™ 9 RD Series are premium heavy duty
crankcase lubricants for locomotive diesel engines.
They meet the severe-service demands of the latest
locomotive engines. The additive system is endorsed
by Electro-Motive Diesel (EMD) and General Electric
(GE). It provides excellent engine protection and
controls oil consumption to promote oil drain interval
extensions.
Viscosity, ASTM D445
Diol 9 RD 40 Diol 9 RD 20W-40 cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
141 135 14.7 15.3 104 118 Pour Point,
°C, ASTM D97 COMMERCIAL
Product
-21
-21
HEAVY DUTY NATURAL GAS ENGINE OILS
Mobil Delvac™ CNG/LNG 15W-40 high performance
heavy duty engine oil is formulated specifically for
spark ignited CNG and LNG fueled truck and bus
engines. It provides excellent performance in the
PASSENGER
COMMERCIAL VEHICLE LUBRICANTS
challenging operating environments presented by CNG
(Compressed Natural Gas) and LNG (Liquefied Natural
Gas) and offers extended drain interval capability.
Viscosity, ASTM D445
Mobil Delvac CNG/LNG 15W-40 cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Sulfated Ash,
wt%, ASTM D874
TBN, mg KOH/g,
ASTM D2896
Pour Point,
ºC, ASTM D97
114 15.3 140 0.9 6.4 -27
SAE
Product
Grade
15W-40
with less varnish, sludge, and carbon build-up under
the most severe operating conditions. Recommended
for Cummins B and C Series and Detroit Diesel Series
50G engines and meets the performance requirements
of Cummins CES 2007, Detroit Diesel 7SE272-9510
and API Service Category CD.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
100
14.4
130
-27
215
5
0.5
Click Here to return to PRODUCT APPLICATION INDEX
62
GREASES
Visit mobil.ca /pds for the most current product information
TBN, mg KOH/g, Sulfated Ash,
ASTM D2896 wt% ASTM D874
AVIATION
Mobil GEO™ 15W-40 is formulated to protect trucks and
buses running on Compressed Natural Gas (CNG) or
Liquefied Natural Gas (LNG). This advanced medium
ash formulation combines high quality base stocks
and balanced additives to deliver excellent oxidation,
nitration, and thermal stability for minimal combustion
chamber ash deposits. Mobil GEO 15W-40 lubricates
MARINE
Product
Mobil GEO 15W-40
INDUSTRIAL
COMMERCIAL VEHICLE LUBRICANTS
COMMERCIAL VEHICLE LUBRICANTS
HEAVY DUTY POWER TRANSMISSION FLUIDS
Mobil Delvac™ Synthetic Transmission Fluid 50 is a
synthetic manual transmission lubricant engineered to
meet extended drain and OEM warranty requirements.
It provides year-round lubrication of manual transmissions in light to severe duty on- and off-highway applications in a wide range of environments. Designed to
Product
Mobil Delvac Synthetic Transmission Fluid 50 Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
ºC, ASTM D97 132 17.5 146 -45
Mobil Delvac™ Synthetic ATF is a synthetic fluid
recommended by Allison Transmission, approved
against the Allison TES-295 Specification. The fluid
meets the demanding requirements of modern heavy
duty automatic transmissions. The synthetic base
oil composition enables excellent performance even
in some of the harshest of operating conditions,
Product
Mobil Delvac Synthetic ATF Mobil Delvac Synthetic Gear 75W-90 Mobil Delvac Synthetic Gear 80W-140 Mobil Delvac™ Synthetic Final Drive and Axle Oil 221
Viscosity, ASTM D445
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
ºC, ASTM D97 39 7.3 168 -54
Flash Point,
°C, ASTM D92
236
ing capability and where extreme pressures and shock
loading are expected. Mobil Delvac Synthetic Gear Oil
75W-90 and 80W-140 incorporate the latest technology in synthetic base stocks and advanced additives
providing significant advantages over mineral gear oils.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
120 310 15.9 31.2 140 139 -48 max -36 max
Mobil Delvac™ Synthetic Final Drive and Axle Oil
is a high performance drivetrain lubricant that meets
the requirements of the Caterpillar FD-1 standard. It
is specifically engineered to provide optimum component life when used as recommended in off-highway
truck and bulldozer final drives, axles, bevel gears,
and differentials, especially those operating under high
Product
Flash Point,
°C, ASTM D92
promoting outstanding gear shifting and power
transfer. Compared to conventional ATF fluids, this
fluid’s inherently high viscosity index and stability
protects against thermal breakdown at high operating
temperatures, while providing outstanding performance
at sub-zero temperatures.
cSt at
40°C
Mobil Delvac™ Synthetic Gear Oils are synthetic
drivetrain lubricants engineered to meet extended
drain and warranty requirements. These products are
for heavy duty drivetrains that require gear lubricants
with relatively high viscosity and excellent load-carry
Product
provide maximum protection and extended operating
life to heavy duty transmissions. Compared to conventional sulphur-phosphorus gear oils, this lubricant
provides significant advantages, including outstanding
high temperature performance, oxidation stability, wear
protection, and corrosion control.
Flash Point,
°C, ASTM D92
205
210
loads and extreme temperatures. Advanced synthetic
base oils and the latest additive technology combine
to promote extended oil drain intervals and to prolong
the life of bearings and gears. The synthetic base oil
composition enables excellent performance in some of
the harshest operating conditions at high temperatures
and at temperatures as low as -35°C.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
320 31.6 138 -45 max 63 Visit mobil.ca /pds for the most current product information
Flash Point,
°C, ASTM D92
246
Click Here to return to PRODUCT APPLICATION INDEX
“Bumper-to-Bumper” Applications
for Your Business*
Gear Oils
Coolant/Antifreeze
Mobil Delvac™ Extended Life Coolant/Antifreeze
Mobil Delvac™ Extended Life 50/50 Coolant/Antifreeze
Mobil Delvac™ Extended Life 55/45 Coolant/Antifreeze
Mobil Delvac™ Synthetic Gear Oil 75W-90; 80W-140
Mobilube™ HD Plus MG 75W; 80W-90; 85W-140
Mobilube™ HD Extra MG 75W; 80W-140
Mobil™ Heavy Duty SCA Precharged Coolant/Antifreeze
Mobil™ Heavy Duty SCA Precharged 50/50 Coolant/Antifreeze
Mobil™ Heavy Duty SCA Precharged 60/40 Coolant/Antifreeze
Mobil™ Heavy Duty SCA Precharged 55/45 Coolant/Antifreeze
Hydraulic Fluids
Mobil SHC™ 500 Series
Mobil DTE 10 Excel™
Mobil Univis™ N-C
Mobil Nuto™ H-C
Engine Oils
Mobil Delvac 1™ ESP 0W-40; 5W-40
Mobil Delvac™ Elite 222 0W-30
Mobil Delvac™ 1300 Super 15W-40; 10W-30
Greases
Mobil Epic™ EP Moly
Mobil Epic™ MQ
Mobil Centaur™ Moly 1
Mobilgrease XHP™ Mine Series
Mobil Unirex™ EP 2
Mobil Unirex™ EP 1 Moly
Transmission and Drivetrain Lubricants
Mobiltrans AST™ Extra 20W
Mobiltrans AST™
Mobiltrans AST™ 30
Mobiltrans HD™ 10W; 30; 50
Mobil Delvac™ Synthetic Final Drive & Axle Oil
Mobil Delvac™ Synthetic ATF
Mobil Delvac™ Synthetic Transmission Fluid 50
Mobilube™ XFD 50
Mobil Hydraul™ Extra
Mobil Hydraul™ 50; 56
*This is a general illustration to identify some of the key components and applications; the list of products is not intended as a specific recommendation for any particular OEM model.
Off-highway applications are different from model to model and OEM to OEM. For specific OEM model recommendations, please contact your Imperial Representative.
HEAVY DUTY POWER TRANSMISSION FLUIDS
Mobilube™ HD LS 80W-90 is a high performance
automotive lubricant formulated from select base
oils and an advanced additive system specifically for
limited-slip differentials. This lubricant is engineered for
API GL-5 level performance in heavy duty limited-slip
Mobilube HD LS 80W-90 Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
ºC, ASTM D97 132 14.3 107 -27
Mobilube™ HD Plus MG 75W, 80W-90 and 85W-140
are high performance commercial gear lubricants
formulated from select base oils and an advanced
additive system. These lubricants are engineered for
heavy duty transmissions, axles and final drives where
extreme pressures and shock loading are expected.
Mobilube HD Plus MG 75W Mobilube HD Plus MG 80W-90 Mobilube HD Plus MG 85W-140 Viscosity, ASTM D445
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
ºC, ASTM D97 92 139 333 15.8 14.5 25.4 184 103 99 -45 -27 -18 Viscosity, ASTM D445
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
ºC, ASTM D97 93
268 15.9
27.4 182 134
-48 -33 Flash Point,
°C, ASTM D92
150
160
due to fatigue. These lubricants deliver excellent performance in heavy duty commercial axles and final drives
subject to extreme pressures and shock loading. They
provide exceptional chemical and thermal stability at
elevated bulk oil temperatures generated under heavy
loads and/or high ambient temperatures.
AVIATION
Mobilube XFD 50 Mobilube XFD 60 150
210
230
chemical and thermal stability at elevated bulk oil
temperatures, good performance at low temperatures,
and protection against rust from water contamination
and wet conditions. Mobilube Extra 80W-140 and
Mobilube HD Extra 75W are recommended as an
API GL-6 lubricant.
cSt at
40°C
Mobilube™ XFD 50 and 60 high performance
drivetrain lubricants are engineered to deliver optimal
component life in Caterpillar final drives and axles
when used as recommended. They are formulated from
advanced base oils and the latest additive technology
to protect bearings and gears from premature failure
Product
Flash Point,
°C, ASTM D92
MARINE
Mobilube™ HD Extra MG 75W Mobilube™ HD Extra 80W-140 They provide excellent chemical and thermal stability
at elevated bulk oil temperatures, good performance
at low temperatures, and good protection against rust
from water contamination and wet conditions. They
deliver excellent performance where API GL-5 or MT-1
lubricants are required.
cSt at
40°C
Mobilube™ HD Extra MG 75W and 80W-140 are high
performance commercial gear lubricants formulated
from select base oils and an advanced additive system.
These lubricants are engineered for heavy duty manual
transmissions, axles, and final drives subject to severe
service with shock loading. They provide excellent
Product
208
PASSENGER
Product
Flash Point,
°C, ASTM D92
COMMERCIAL
Product
differentials, axles, and final drives where extreme
pressures and shock loading are expected. This
product delivers exceptional chemical and thermal
stability at elevated bulk oil temperatures.
INDUSTRIAL
COMMERCIAL VEHICLE LUBRICANTS
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
ºC, ASTM D97 206 334 18.4 25.2 97 97 --24
-15 250
255
Click Here to return to PRODUCT APPLICATION INDEX
66
GREASES
Visit mobil.ca /pds for the most current product information
Flash Point,
°C, ASTM D92
COMMERCIAL VEHICLE LUBRICANTS
HEAVY DUTY POWER TRANSMISSION FLUIDS
Mobiltrans™ AST (All-Season Transmission) is
a high performance drivetrain lubricant engineered
to meet or exceed the requirements of Caterpillar’s
TO-4M performance specifications for off-highway
transmissions, drivetrains and hydraulic systems.
This advanced technology lubricant provides clutch
and brake compatibility and extended life that has
Product
Mobiltrans AST not been possible with previous formulations.
Mobiltrans AST combines a blend of semi-synthetic
base oils with an advanced additive system. The
product provides all-season lubrication of all drivetrain
components in light to severe duty off-highway equipment operating in a wide range of environments.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
ºC, ASTM D97 107 14.2 134 -39
Mobiltrans™ AST 30 and Mobiltrans™ AST Extra 20
high performance multigrade transmission and drive
train lubricants are uniquely designed to provide low
temperature and multi-season service in powershift
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
ºC, ASTM D97 Mobiltrans AST 30 Mobiltrans AST Extra 20
57.6 32.9
10.5 7.5
173 206 -45
-54
Mobiltrans™ HD 10W, 30 and 50 are high performance
heavy duty transmission and drivetrain lubricants
engineered to meet or exceed the requirements of
the rigorous Caterpillar TO-4 specification. This product
line is uniquely designed to optimize the performance
of powershift transmissions, gearboxes, and final
drives. In hydraulic applications, they provide maximum
Mobiltrans HD 10W Mobiltrans HD 30 Mobiltrans HD 50 222
transmissions, gearboxes, clutches, final drives and
hydraulic systems. Mobiltrans AST 30 is recommended
for temperatures as low -35°C; Mobiltrans AST Extra 20
can be used at -45°C.
Product
Product
Flash Point,
°C, ASTM D92
Flash Point,
°C, ASTM D92
180
170
protection even in high pressure systems. Select
base oils combine with an advanced additive system
to deliver the precision needed to maximize productivity in construction, quarrying and mining equipment
operating in severe conditions. These products offer an
advantage over mixed fleet engine oils and previously
used lubricants meeting Caterpillar TO-2.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
ºC, ASTM D97 42 100 195 6.3 11.2 18.0 96 97 100 -33
-18 -15 67 Visit mobil.ca /pds for the most current product information
Flash Point,
°C, ASTM D92
202
224
240
Click Here to return to PRODUCT APPLICATION INDEX
TRACTOR HYDRAULIC FLUIDS
calling for a “heavier” viscosity fluid in summer
operation or “all-season” use where temperatures
are above -25°C. Mobil Hydraul 50 is recommended
for year-round service in systems calling for a “lighter”
viscosity fluid, and as a winter grade replacement for
Hydraul 56 in temperatures as low as -35°C. Hydraul
Extra is an all-season fluid suitable for the most severe
applications across an operating temperature range
of -35°C to 100°C.
Viscosity, ASTM D445
Product
Mobil Hydraul 50 Mobil Hydraul Extra Mobil Hydraul 56 cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
°C, ASTM D5949
34 43
55
7.25
9.6
9.30
181
218
145
-54
-51
-42
Flash Point,
°C, ASTM D92 COMMERCIAL
Mobil Hydraul™ high performance multipurpose
tractor lubricants are for agriculture, forestry, mining
and construction equipment where a common oil sump
is used for transmission, differential, final drive, wet
brake, wet clutch and hydraulic components. Advanced
lubrication technology optimizes the performance of
equipment operating in a wide range of environments
and conditions. All grades are well suited for reducing
wet brake chatter. Mobil Hydraul 56 is for systems
INDUSTRIAL
COMMERCIAL VEHICLE LUBRICANTS
170
170
200
PASSENGER
COMMERCIAL VEHICLE LUBRICANTS
RAILWAY
Density Product
@ 15°C kg/m3
Galcar All Year 872
stocks combine with high performance additives to
inhibit oxidation and promote long service life, high
load-carrying capability, control of rust and corrosion,
good water separation and low temperature fluidity.
Kinematic Viscosity
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270 Pour Point,
°C, ASTM D5949
Flash Point,
°C, ASTM D92
40
6.3
102
-39
225
MARINE
Galcar All Year is formulated for the lubrication of
railway car journal bearings and locomotive suspension
bearings. It meets the specifications of major Canadian
railways and the all-year specification of the American
Association of Railways (AAR). High quality base
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
68
GREASES
Visit mobil.ca /pds for the most current product information
COMMERCIAL VEHICLE LUBRICANTS
COOLANT/ANTIFREEZE
Mobil Delvac™ Extended Life Coolant/Antifreeze
– C Series feature a patented Hybrid and Organic
Acid Technology (OAT) formula that protects cooling
systems for 960,000 km on-highway use or 6 years /
12,000 hours of off-highway use when added as an
initial fill and properly maintained. Designed for use
in on-highway truck, off-highway farm, marine,
and stationary applications, including but not limited
to Caterpillar, Detroit / MTU, GM Heavy Truck,
Freightliner, PACCAR and Volvo Mack. Available in
concentrate as well as 50/50 and 55/45 prediluted
versions. Colour: Red
Mobil™ Heavy Duty SCA Precharged Coolant/
Antifreeze is a fully formulated traditional engine
coolant for multi-vehicle fleets, including automotive,
light duty and heavy duty diesel applications such as
on-highway truck, off-highway and farm applications.
It provides optimum protection against freezing,
overheating, cavitation, erosion, corrosion and scale
for all heavy duty cooling system applications.
Because it is precharged with a Supplemental Coolant
Additive (SCA), Mobil Heavy Duty Precharged Coolant/
Antifreeze requires no SCAs at initial fill and ensures
proper chemistry at every top-off. Available in concentrate as well as 60/40, 55/45, and 50/50 prediluted
versions. Colour: Purple.
69 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
PASSENGER VEHICLE LUBRICANTS
PASSENGER VEHICLE ENGINE OILS
PASSENGER VEHICLE LUBRICANTS
PRODUCT
PAGE
Passenger Vehicle Engine Oils Engine Oil Selection Chart....................................... 71-72
Engine Oil Selection Star Chart....................................73
Mobil 1™ ESP Formula 5W-30.....................................75
Mobil 1™ ESP Formula M 5W-40.................................75
Mobil 1™ Extended Performance 5W-20,
5W-30 and 10W-30.......................................................75
Mobil 1™ Turbo Diesel Truck 5W-40............................. 76
Mobil Super™ 1000...................................................... 76
Mobil Super™ 2000...................................................... 76
Mobil Super™ 3000...................................................... 76
Passenger Vehicle Drive Train Fluids Mobil 1™ Synthetic ATF................................................77
Mobil™ Dexron®-VI ATF...............................................77
Mobil™ Multi-Vehicle ATF.............................................77
Mobil ATF™ D/M...........................................................77
Mobil ATF™ +4.............................................................77
Mobil ATF™ 3309.........................................................77
Mobil 1™ Synthetic Gear Lube LS................................78
Motorcycle Oils
Mobil 1™ Racing 4T.....................................................78
Passenger Vehicle Installer Greases ......................................................................................78
Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
AVIATION
Mobil 1™ ESP X1 0W-30..............................................75
MARINE
PASSENGER
Mobil 1™ Advanced Fuel Economy.............................. 74
Mobil 1™....................................................................... 74
COMMERCIAL
INDUSTRIAL
GREASES
70
Most vehicles that
specify 0W-20 (newer
Toyotas and Hondas),
5W-20 and certain
hybrids.
GF-5,SN
A1/B1
A1/B1
A5/B5
dexos 1®X
MB
BMW
71 Visit mobil.ca /pds for the most current product information
Vehicles that require
GF-5,SN
10W-30.
A1/B1
A5/B5
*For a full list of Industry and original equipment manufacturer approvals by product and viscosity see the Product Data Sheets available online at mobil.ca/pds
Mobil 1™ 10W-30
Advanced synthetic formula designed for domestics and imports.
Mobil 1™ 0W-40
Advanced synthetic
Many European vehicles. SN, Porsche
A3/B3
229.3 /
Longlife-01
formulation designed to meet
A40, Nissan
A3/B4
229.5
the requirements of many
GT-R, Chrysler
European vehicles.
MS10850,
Chrysler
MS10725
Mobil 1™ 5W-20
Advanced synthetic formula
Vehicles that require GF-5,SN
A1/B1
dexos 1®X
designed to meet the
5W-20
requirements of newer
domestic and import vehicles.
Mobil 1™ 5W-30
Advanced synthetic formulation
Vehicles that require
GF-5,SN
A1/B1 dexos 1®X
designed to meet the requirements5W/30.
Honda/Acura
A5/B5
of many domestic, including
Corvette approved.
HT0-06
GM, and imported vehicles.
Mobil 1™ 5W-50
Higher viscosity, advanced Porsche.
SN, Porsche
A3/B3 229.1 /
High
synthetic formula designed for A40
A3/B4
229.3
Performance
performance vehicles.
Diesel Oil
Mobil 1™
0W-20
Advanced synthetic formula
designed for enhanced fuel
economy and cold weather
performance.
Vehicles that require
GF-5,SN
10W-30.
dexos 1®X
Boosted, advanced synthetic
formula designed for today’s
longer oil change intervals.
For use in many domestic and
imported vehicles.
A1/B1
A5/B5
Mobil 1™ 10W-30
Extended Performance
GF-5,SN
Honda/Acura
HT0-06
Boosted, advanced synthetic Vehicles that require
formula designed for today’s 5W-30 or 10W-30.
longer oil change intervals.
For use in many domestic and
imported vehicles.
Mobil 1™ 5W-30
Extended
Performance
Ford
Service Fill
Boosted, advanced synthetic
Vehicles that require
GF-5,SN
A1/B1
dexos 1 X
formula designed for today’s
5W-20.
longer oil change intervals.
For use in many domestic and
imported vehicles.
®
GM
Service Fill
Mobil 1™
5W-20
Extended
Performance
Recommended
API, ILSAC,
Brand Name Viscosity Product Description
Consumer Applications & Other Industry*
ACEA
501.01 /
505.00
502.00 /
505.00
VW
PASSENGER VEHICLE LUBRICANTS
PASSENGER VEHICLE ENGINE OIL SELECTION CHART
Click Here to return to PRODUCT APPLICATION INDEX
Boosted, higher viscosity,
advanced synthetic formula
designed for performance
vehicles.
HT/HS applications. Racing and Flat tappet
applications.
Low SAPS (sulphated ash,
phosphorous sulphur). Available at most
Mercedes Benz dealers.
SN, JASO MA1
2006
Mobil 1™
10W-40
Racing 4T
MARINE
AVIATION
Longlife-04
BMW
VW
229.31 /
Longlife-04
229.51
504.00 /
507.00
229.31 / 229.51
229.31 / 229.51 /
229.52
MB
PASSENGER VEHICLE ENGINE OIL SELECTION CHART
72
GREASES
*For a full list of Industry and original equipment manufacturer approvals by product and viscosity see the Product Data Sheets available online at mobil.ca/pds
PASSENGER
Click Here to return to PRODUCT APPLICATION INDEX
COMMERCIAL
Visit mobil.ca /pds for the most current product information
Advanced synthetic formulas
All motorcycles where
designed specifically for
10W-40 is specified
motorcycles where clutch
lubrication is also important.
SN, Porsche
C3, C2
C30, Chrysler
MS-11106,
PSA B712290,
PSA B712297,
JASO DL-1
Mobil 1™ ESP 5W-30
Advanced synthetic formula
Low SAPS (sulphated ash,
Formula
designed specifically for phosphorous sulphur).
passenger car diesels that have diesel particulate filters.
Advanced synthetic formula
designed specifically for passenger car diesels that have
diesel particulate filters.
Mobil 1™ ESP 5W-40
Formula M
E7
A3/B3
High performance ACEA C2, C3
gasoline and diesel
engines found in the latest passenger cars,
SUVs and light vans.
CJ-4, CI-4, CI-4 Plus, SN,
Caterpillar
ECF-2 and ECF-3
SN
Ford
Service Fill
Mobil 1™ ESP 0W-30 Advanced synthetic formulation
X1
expertly engineered for extreme conditions
Mobil 1™ Turbo 5W-40
Advanced synthetic formula Most diesel applications.
Diesel Truck
designed for diesel powered
including engines with
pick-ups and trucks.
diesel particulate filters.
Mobil 1™
15W-50
GM
Service Fill
PASSENGER VEHICLE LUBRICANTS
INDUSTRIAL
Recommended
API, ILSAC,
Brand Name Viscosity Product Description
Consumer Applications & Other Industry*
ACEA
PASSENGER VEHICLE PRODUCT LISTING BY APPLICATION
Choose the Best Protection for Your Vehicle
73 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
PASSENGER VEHICLE LUBRICANTS
PASSENGER VEHICLE ENGINE OILS
Fuel Economy meets or exceeds the requirements
of the latest industry standards and outperforms our
conventional oils. Recommended for SAE 0W-30,
5W-30 and 10W-30 applications.
Mobil 1™ 0W-40. Mobil 1 is the world’s leading synthetic motor oil brand delivering our ultimate performance and protection. Mobil 1 0W-40 European Car
Formula (North America) or Protection Formula (rest
of the World) is engineered for the latest gasoline and
diesel (without Diesel Particulate Filters or DPFs) engine
technology. It provides exceptional cleaning power, wear
protection and overall performance and keeps your
engine running like new in all driving conditions.
Mobil 1™ 5W-20 and 5W-30 are advanced synthetic
engine oils designed to keep your engine running like
new by delivering exceptional wear protection, cleaning
power and overall performance. Mobil 1 5W-20 and
5W-30 meet or exceed the industry’s toughest standards and outperform conventional oils. Mobil 1 lubricants are standard equipment (factory filled) in many
new cars, including select high performance vehicles.
Mobil 1™ 5W-50 advanced synthetic engine oil
promotes exceptional wear protection for a smooth
driving experience every time. It meets or exceeds
industry and manufacturers’ standards for high performance turbocharged, supercharged gasoline and
diesel multi-valve fuel injected engines. It is especially
suited for high speed and severe service associated
with stop and go driving. For racing or everyday driving,
Mobil 1 5W-50 delivers heavy duty performance and
protection for an outstanding driving experience.
Mobil 1™ 10W-30 advanced synthetic engine oil helps
keep engines running like new by providing exceptional
cleaning power, wear protection and overall performance. It meets or exceeds latest industry standards
for modern gasoline engines. Mobil 1 lubricants are
standard equipment (factory filled) in many new cars,
including select high performance vehicles.
Mobil 1™ 15W-50 is an advanced synthetic engine oil
that delivers exceptional wear protection for a smooth
driving experience. It meets or exceeds industry and
manufacturers’ standards for high performance turbocharged, supercharged gasoline and diesel multi-valve
fuel injected engines. This winning, race-proven
technology is especially suited for a wide variety
of motorsports, towing, and other severe-service
applications. Mobil 1 15W-50 helps deliver outstanding
performance and protection for the winning edge.
Mobil 1 0W-20 Advanced Fuel Economy Mobil 1 0W-30 Advanced Fuel Economy
Mobil 1 0W-40 Mobil 1 5W-20 Mobil 1 5W-30 Mobil 1 5W-50 Mobil 1 10W-30 Mobil 1 15W-50 Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
44.8 62.9
75 49.8 61.7 108 63.2 125 8.7 10.9
13.5 8.9 1
11.0 17.5 10.1 18 V.I.
Pour Point
ASTM D2270
°C, ASTM D97
173
166
185 160 172 180 146 160 -48 -50
-48 -43 -42 -45
-42 -39 Flash Point,
°C, ASTM D92
224
226
230
230
230
231
232
232
AVIATION
Product*
* vehicle owners should consult their service manuals for the recommended oil viscosity grade
Click Here to return to PRODUCT APPLICATION INDEX
74
GREASES
typical values, actual values may vary
Visit mobil.ca /pds for the most current product information
MARINE
Mobil 1™ 0W-30 Advanced Fuel Economy is an
advanced high performance synthetic engine oil
designed to help deliver outstanding engine protection
and enhanced fuel economy. Mobil 1 0W-30 Advanced
PASSENGER
Economy meets or exceeds the requirements of the
latest industry standards and outperforms conventional
oils. Mobil 1 0W-20 Advanced Fuel Economy is recommended for SAE 0W-20 and 5W-20 applications.
COMMERCIAL
Mobil 1™ 0W-20 Advanced Fuel Economy is an advanced high performance synthetic engine oil designed
to help deliver outstanding engine protection and
enhanced fuel economy. Mobil 1 0W-20 Advanced Fuel
INDUSTRIAL
PASSENGER VEHICLE LUBRICANTS
PASSENGER VEHICLE ENGINE OILS
Mobil 1™ ESP X1 0W-30 advanced synthetic engine
oil helps provide exceptional cleaning power, wear
protection and overall performance. Expertly engineered
to help prolong the life and maintain the efficiency of
Product
Mobil 1 ESP X1 0W-30 Viscosity, ASTM D445
HTHS Viscosity
cSt at
40°C
cSt at
100°C
Sulfated Ash,
wt% ASTM D874
MRV at -40°C
mPa’s at 150°C
ASTM D4683
TBN, mg KOH/g,
ASTM D2896 65 12.1 0.8
24,800 3.5 7.6
Mobil 1™ ESP Formula M 5W-40 is an advanced
performance synthetic engine oil designed to help
provide exceptional cleaning power, wear protection
and overall performance. It is engineered to help
Product
Mobil 1 ESP Formula M 5W-40 Mobil 1 Extended Performance 5W-20 Mobil 1 Extended Performance 5W-30 Mobil 1 Extended Performance 10W-30 prolong the life and maintain the efficiency of emission
systems in both diesel and gasoline powered vehicles
requiring an oil approved against Mercedes Benz
229.31 and MB 229.51 specifications.
cSt at
40°C
cSt at
100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
81 13.4 167 -39 Flash Point,
°C, ASTM D92
236
oil changes. Mobil 1 Extended Performance is
specially formulated to help provide outstanding
protection during today’s longer oil change intervals.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point,
°C, ASTM D92
49.6 59.8 63.7 8.9 10.6 10.2 161 169 147 -42 -40 -39
230
230
232
Mobil 1™ Turbo Diesel Truck 5W-40 is a synthetic
performance heavy duty diesel engine oil that helps to
extend engine life while providing long drain capability
and helps improve fuel economy for modern diesel
Viscosity, ASTM D445
Mobil 1™ Extended Performance 5W-20, 5W-30
and 10W-30 are advanced synthetic engine oils
designed to keep your engine running like new and
to protect critical engine parts for 25,000 km between
Product
emission systems in diesel and gasoline powered
automobiles, this product meets or exceeds leading
industry and car manufacturers’ standards for newer
diesel and gasoline powered passenger car engines.
engines operating in severe applications. State-of-the-art
lubricant technology helps deliver exceptional performance in modern low emission engines, including refrigerated units, as well as older, well-maintained engines.
Viscosity, ASTM D445
Product
cSt at
40°C
cSt at
100°C
Mobil 1 Turbo Diesel Truck 5W-40 97.9 14.5 75 Visit mobil.ca /pds for the most current product information
Flash Point,
V.I.
°C, ASTM D92
153 215
Click Here to return to PRODUCT APPLICATION INDEX
PASSENGER VEHICLE LUBRICANTS
PASSENGER VEHICLE ENGINE OILS
Mobil Super™ 1000 motor oils are formulated from
quality base stocks combined with modern performance additives to give your engine the protection
and the performance you expect under a wide variety
of operating conditions. These products meet or
exceed ILSAC GF-5 and API SN. Those claims are
backward compatible with earlier performance levels
such as API SM, SL, and SJ. The American Petroleum
Institute (API) classifies these products as “resource
conserving.”
cSt at
40°C
cSt at
100°C
V.I.
CCS, cP
MRV, cP
Pour Point,
°C, ASTM D97
Flash Point
°C, ASTM D92
Spec. Gravity
kg/l at 15.6°C
49 62 69 8.6 10.4 10.6 152 157
141 5,880 @ -30°C
6,440 @ -30°C 6,040 @ -25°C
26,900 @ -35°C
30,300 @ -35°C
18,700 @ -30°C
-31 -33
-33 221 220 222 0.860
0.860
0.869
Mobil Super™ 1000 5W-20 Mobil Super™ 1000 5W-30 Mobil Super™ 1000 10W-30 Mobil Super™ 2000 oils combine synthetic and
conventional high quality base oils with friction reducing
additives to help provide long engine life and outstandViscosity, ASTM D445
cSt at
40°C
cSt at
100°C
Mobil Super 2000 5W-20 Mobil Super 2000 5W-30 Mobil Super 2000 10W-30 46.9 61.4 66.3 8.3 10.4 10.4 Pour Point,
V.I.
°C, ASTM D97
153 159 145 Mobil Super™ 3000 synthetic motor oils help provide
long engine life and outstanding protection in vehicles
of all ages, even under severe conditions and across
a wide range of operating temperatures. These oils
outperform our conventional synthetic blended products, provide outstanding protection against sludge,
engine rust and corrosion and optimum viscosity
and fluidity across a broad range of temperatures.
Mobil Super 3000 0W-20 Mobil Super 3000 Formula D1 5W-30 Spec. Gravity
kg/l at 15.6°C
218 222 220 0.8590
0.8590
0.8667
Mobil Super 3000 0W-20 and 5W-30 are classified
by The American Petroleum Institute (API) as
“resource conserving” and meet or exceed
ILSAC GF-5. Those claims are backward compatible
with earlier performance levels such as API SN,
SM, SL, and SJ and previous LSAC categories.
Mobil Super 3000 Formula D1 5W-30 is approved
against General Motors dexos1®.
MARINE
Product
-36
-36
-36 Flash Point
°C, ASTM D92
PASSENGER
Product
ing protection for vehicles with more than 120,000 km.
Formulated with seal conditioner, these oils help prevent
leaks and reduce oil consumption.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
Pour Point, °C, ASTM D97
Flash Point
°C, ASTM D92
Spec. Gravity
kg/l at 15.6°C
44.9 65.1 8.6 11.2 173 167 -42 -39 238 239 0.848
0.8378 COMMERCIAL
Viscosity, ASTM D445
Product
INDUSTRIAL
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
76
GREASES
Visit mobil.ca /pds for the most current product information
PASSENGER VEHICLE LUBRICANTS
PASSENGER VEHICLE DRIVE TRAIN FLUIDS
Mobil 1™ Synthetic ATF is a multi-vehicle, synthetic
fluid designed to meet the demanding requirements
of modern passenger vehicles. It helps to improve
Viscosity, ASTM D445
Product
Colour
Mobil 1 Synthetic ATF Red
cSt at
40°C
cSt at
100°C
V.I.
Pour Point, °C, ASTM D97
Flash Point,
°C, ASTM D92
36.3 7.4 176 -51
220
Mobil™ Dexron®-VI ATF is a high performance, synthetic blend ATF formulation that meets or exceeds the stringent requirements of GM’s DEXRON-VI specification
Product
Colour
Mobil Dexron-VI ATF
Red
Product
Colour
Red
cSt at
40°C
cSt at
100°C
29.5 5.83 Product
Colour
Mobil ATF D/M Red
cSt at
40°C
cSt at
100°C
34.1 7.42 Product
Colour
Mobil ATF +4 Red
cSt at
40°C
cSt at
100°C
35.3 7.4 Product
Colour
Mobil ATF 3309 Red
220
Flash Point,
V.I.
°C, ASTM D92
193 180
Flash Point,
V.I.
°C, ASTM D92
183 356
tional properties, excellent low-temperature fluidity and
dependable wear protection required in applications
where a Chrysler MS-9602 type fluid is recommended.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
34.4 7.5 Mobil ATF™ 3309 is a high performance lubricant
that meets original equipment manufacturers’ spec-
145 is recommended for applications requiring:
GM DEXRON®, Ford MERCON® and Allison C-4 or
GM DEXRON® III H.
Viscosity, ASTM D445
Mobil ATF™ +4 is specially formulated to ensure optimal performance in Chrysler automatic transmissions.
Its unique additive package provides the proper fric-
Flash Point,
V.I.
°C, ASTM D92
mance levels. Recommended by Imperial for use in
applications requiring Dexron III. Mobil Multi-Vehicle
ATF is not recommended for applications requiring
Ford MERCON LV, MERCON SP, or GM DEXRON VI.
Viscosity, ASTM D445
Mobil ATF™ D/M provides the excellent oxidation and
friction stability, anti-wear properties, and low-temperature fluidity desired for most automatic transmissions. It
and provides warranty protection for model year 2006
and later GM vehicles. It also delivers improved performance in older GM vehicles requiring DEXRON fluid.
Viscosity, ASTM D445
Mobil™ Multi-Vehicle ATF is a premium lubricant
for car and truck automatic transmissions and other
applications & recommended by Imperial for use in
applications that require an automatic transmission
fluid satisfying Ford Mercon and Mercon V perfor-
Mobil Multi-Vehicle ATF and extend transmission efficiency, smooth shifting
performance and helps improve fuel economy.
Flash Point,
V.I.
°C, ASTM D92
192 392
ifications for use in certain slip-controlled lock-up
automatic transmissions.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
33 7.1 77 Visit mobil.ca /pds for the most current product information
Flash Point,
V.I.
°C, ASTM D92
181 198
Click Here to return to PRODUCT APPLICATION INDEX
PASSENGER VEHICLE LUBRICANTS
PASSENGER VEHICLE DRIVE TRAIN FLUIDS
Mobil 1™ Synthetic Gear Lube LS is a high
performance, synthetic, multipurpose automotive
gear lubricant. It is designed to meet the requirements
Mobil 1 Synthetic Gear Lube LS 75W-90
Mobil 1 Synthetic Gear Lube LS 75W-140 Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
99 170 15.2 24.4 Pour Point, V.I.
°C, ASTM D97
142 175 -39
-48 Flash Point,
°C, ASTM D92
COMMERCIAL
Product
of modern passenger vehicles in many types of
operating conditions, including limited slip applications
and to deliver outstanding power transfer performance.
150
207
Additional Passenger Vehicle Drive Train Fluids
Mobilube™ HD Plus 80W-90 and 85W-140............... 66
Mobilube™ HD Plus MG 75W.................................... 66
Mobilube™ HD LS 80W-90........................................ 66
Mobilube™ HD Extra 80W-140.................................. 66
Mobilube™ HD Extra MG 75W................................... 66
PASSENGER VEHICLE LUBRICANTS
PASSENGER
INDUSTRIAL
MOTORCYCLE OILS
Product
Mobil 1™ Racing 4T 10W-40 Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
82.0 13.1 Pour Point, V.I.
°C, ASTM D97
161 -45 Flash Point,
°C, ASTM D92
212
PASSENGER VEHICLE LUBRICANTS
AVIATION
capacity in engines or transmissions. Synthetic fluids
require significantly less thickener to achieve a multigrade viscosity rating and, in some cases, require no
thickener at all. As a result, synthetic formulations tend
to be very shear-stable and provide a solid, protective
oil film for engine bearings, piston rings, transmission
gears and other critical engine parts.
MARINE
Mobil 1™ Racing 4T is an advanced performance
synthetic motorcycle oil whose unique synthetic structure delivers advantages beyond conventional products
of similar viscosities. Conventional base oils become
lighter in viscosity as temperature increase, which
forces the use of thickeners to help the lubricant
maintain viscosity as temperatures increase. These
thickeners can shear down and lose their thickening
PASSENGER VEHICLE INSTALLER GREASES
Mobil 1™ Synthetic Grease........................................ 91
Mobil Ronex™ MP...................................................... 91
Mobilgrease XHP™ 220 Series.................................. 97
Click Here to return to PRODUCT APPLICATION INDEX
78
GREASES
Visit mobil.ca /pds for the most current product information
QUESTIONS?
CALL OUR TECHNICAL SUPPORT CENTER AT
1 888 968-3776
mobilindustrial.com | mobildelvac.ca | mobil.ca
MARINE LUBRICANTS LISTING BY APPLICATION
INDUSTRIAL
COMMERCIAL
PAGE
Crosshead Engine Oils
Mobilgard™ 570....................................................................... 81
Mobilgard™ 560 VS................................................................. 81
Mobilgard™ 525....................................................................... 81
Mobilgard™ 300....................................................................... 81
Trunk Piston Engine Oils
Mobilgard™ ADL Series........................................................... 82
Mobilgard™ 12 Series.............................................................. 82
Mobilgard™ 410 NC (No Chlorine)........................................... 82
Mobilgard™ M30, M40 and M50.............................................. 82
Marine Hydraulic Oil
Mobil SHC Aware™ H Series................................................... 83
Marine Grease
Mobil SHC Aware™ Grease EP 2............................................ 83
Click Here to return to PRODUCT APPLICATION INDEX
80
GREASES
Visit mobil.ca /pds for the most current product information
AVIATION
For more information, please refer to exxonmobil.com/marinelubes-en
MARINE
PRODUCT
PASSENGER
MARINE LUBRICANTS
MARINE LUBRICANTS
CROSSHEAD ENGINE OILS
Mobilgard™ 570 is a premium quality, extra high
performance, marine diesel engine cylinder oil. The
outstanding performance of Mobilgard 570 has been
demonstrated at the elevated peak firing pressures
and liner temperatures found in modern marine two
stroke engines. It has an optimum viscosity of over
20 cSt. at 100ºC and low volatility to ensure excellent
lubricant distribution and oil film retention. Through
Product
Mobilgard 570
Viscosity, ASTM D445 Spec. Gravity,
cSt at
cSt at
V.I.
Pour Point,
Flash Point,
kg/l at 15°C
40°C
100°C
ASTM D2270
°C, ASTM D97
°C, ASTM D92
ASTM D1298
222
20
104
Mobilgard™ 560 VS is a high performance marine
diesel engine cylinder oil for crosshead engines running on heavy fuel with sulphur levels from 0.5-4.0%.
Advanced technology delivers superb protection from
corrosive and adhesive wear at the higher tempera
Product
Mobilgard 560 VS
Product
Mobilgard 525
222
20
Product
Mobilgard 300
256
0.937
-9
256
0.937
20
102
-9
286
0.909
12
TBN, mg KOH/g,
ASTM D2896
60
TBN, mg KOH/g,
ASTM D2896
25
engines. This oil has sufficient alkalinity to neutralize
strong acids entering the crankcase via fuel sulphur
combustion. Enhanced load-carrying ability helps
reduce wear in heavily loaded bearings.
Viscosity, ASTM D445 Spec. Gravity,
cSt at
cSt at
V.I.
Pour Point,
Flash Point,
kg/l at 15°C
40°C
100°C
ASTM D2270
°C, ASTM D97
°C, ASTM D92
ASTM D1298
111
70
extreme environments, Mobilgard 525 has an optimum
viscosity of 20 cSt at 100ºC and low volatility to ensure
lubricant distribution and oil film retention and help
protect engine parts.
Viscosity, ASTM D445 Spec. Gravity,
cSt at
cSt at
V.I.
Pour Point,
Flash Point,
kg/l at 15°C
40°C
100°C
ASTM D2270
°C, ASTM D97
°C, ASTM D92
ASTM D1298
226
TBN, mg KOH/g,
ASTM D2896
tures and pressures found in modern crosshead
engines. The outstanding performance of this oil
has been demonstrated at the highest peak firing
pressures and liner temperatures.
104
Mobilgard™ 300 is an extra high performance system
oil for crosshead diesel engines. High quality paraffinic
base oils and a balanced additive system provide
excellent protection for the severe operating conditions
of recent design, high output crosshead marine diesel
-9
Viscosity, ASTM D445 Spec. Gravity,
cSt at
cSt at
V.I.
Pour Point,
Flash Point,
kg/l at 15°C
40°C
100°C
ASTM D2270
°C, ASTM D97
°C, ASTM D92
ASTM D1298
Mobilgard™ 525 is a marine diesel engine cylinder
oil for crosshead engines running low and ultra low
sulphur distillate fuels and meets the requirements
of MAN and Wartsila engines. Designed to protect in
the use of unique synthetic thickener technology and
a balanced formulation, the high viscosity and low
volatility is attained with little or no use of bright stock
which can create deposit formation due to poor thermal
stability. Mobilgard 570 has demonstrated outstanding
ring and liner protection and cleanliness under sustained operation with fuel sulphur levels down to 1.5%.
97
81 Visit mobil.ca /pds for the most current product information
-12
266
0.889
TBN, mg KOH/g,
ASTM D2896
5
Click Here to return to PRODUCT APPLICATION INDEX
MARINE LUBRICANTS
TRUNK PISTON ENGINE OIL
Product
Mobilgard ADL 30
Mobilgard ADL 40
in severe-service applications and promotes removal
of sludge and deposits. Mobilgard ADL Series oils minimize oil consumption associated with liner lacquering,
improves overall engine cleanliness and help increase
overhaul intervals. Excellent load-carrying properties
minimize piston ring and liner wear, and make these
lubricants suitable for marine gearing applications.
Viscosity, ASTM D445
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Spec. Gravity,
kg/l at 15°C
ASTM D1298
TBN, mg KOH/g,
ASTM D2896
11.5
14.7
117
112
-30
-21
230
239
0.889
0.892
12
12
Mobilgard™ 12 Series high performance diesel
engine oils are for trunk piston engines operating on
low sulphur distillate fuels in marine and industrial
applications. They deliver excellent resistance to
Product
Mobilgard 312
Mobilgard 412
oxidation and viscosity increase over long service,
along with outstanding water separation and excellent
protection against corrosion.
Viscosity, ASTM D445
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Spec. Gravity,
kg/l at 15°C
ASTM D1298
TBN, mg KOH/g,
ASTM D2896
12.0
14.5
100
10
-9
-9
266
272
0.896
0.899
15
15
Product
Mobilgard 410 NC
corrosion protection when using fuels containing up
to 0.05 wt.% sulfur, even though metals such as steel,
copper, silver and bronze are present. It has excellent
lubricating properties and has high viscosity index to
help reduce oil consumption, and is optimized for low
and ultra low sulfur fuel use and is LNG, biofuel and
Tier IV engine ready.
Viscosity, ASTM D445
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Spec. Gravity,
kg/l at 15°C
ASTM D1298
TBN, mg KOH/g,
ASTM D2896
14.4
104
-18
255
0.894
10
Product
Viscosity, ASTM D445
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Spec. Gravity,
kg/l at 15°C
ASTM D1298
TBN, mg KOH/g,
ASTM D2896
12.0
14.0
14.0
14.0
100
100
100
100
-6
-6
-6
-6
244
250
242
228
0.907
0.907
0.915
0.922
30
30
40
50
Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
82
GREASES
Mobilgard M330
Mobilgard M430
Mobilgard M40
Mobilgard M50
standing residual fuel compatibility for excellent cleanliness, especially in the crankcase, camshaft, ring belt
and piston undercrowns. They demonstrate excellent
high temperature oxidation and thermal stability, low
volatility, high load-carrying properties and protection
against corrosion.
AVIATION
Mobilgard™ M30, M40 and M50 are three series of
extra high performance engine oils for severe residual
fuelled medium speed diesel engines in marine and
stationary power applications. The number in each
name refers to TBN. These market leading trunk piston
engine oils employ potent additives and deliver out-
MARINE
Mobilgard™ 410 NC (No Chlorine) engine oil is
a non-zinc and non-chlorine lubricant specifically
formulated with an Electro Motive Diesel (EMD)
and General Electric (GE) endorsed additive technology to meet requirements of heavily loaded diesel
engines manufactured by EMD and used in marine
applications. Its alkalinity reserve provides excellent
PASSENGER
COMMERCIAL
Mobilgard™ ADL Series increased dispersancy
engine oils are for high BMEP medium and high speed
diesel engines operating on distillate and MDO fuels.
These oils are available in SAE 30 and 40 grades to
suit most marine engine viscosity requirements. A
special balance of detergent and dispersant delivers
increased resistance to cylinder liner lacquer formation
INDUSTRIAL
MARINE LUBRICANTS
MARINE HYDRAULIC OIL
Mobil SHC Aware™ H Series lubricants are high
performance, anti-wear hydraulic oils for modern
high pressure hydraulic systems that meet the U.S.
Environmental Protection Agency (EPA) 2013 Vessel
General Permit (VGP) guidelines for “environmentally
acceptable lubricants.” They provide excellent wide
temperature range performance above and beyond
Product
Mobil SHC Aware H 32
Mobil SHC Aware H 46
Mobil SHC Aware H 68
the capabilities of non-synthetic environmentally acceptable oils. Mobil SHC Aware H Series oils are specially formulated from ester base stocks and provide
exceptional anti-wear and film strength characteristics
necessary for hydraulic systems operating under high
load and high pressures.
Viscosity, ASTM D445
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
32
46
68
6.0
8.2
10.37
140
140
140
-30
-30
-30
Flash Point,
°C, ASTM D92 185
185
185
MARINE LUBRICANTS
MARINE GREASE
Mobil SHC Aware™ Grease EP 2 is a high performance synthetic grease designed specifically for applications which are environmentally sensitive and meets
the requirements of the U.S. Environmental Protection
Agency (EPA) 2013 Vessel General Permit (VGP).
Product
Mobil SHC Aware Grease EP 2
This leading product is readily biodegradable and virtually non-toxic grease and is formulated based on biodegradable saturated ester base oils and a lithium/calcium
soap thickener. It does not emulsify and has excellent
water wash and salt water corrosion resistance.
Viscosity, ASTM D445
cSt at 40°C
Colour,
Visual
NLGI
Grade
Thickener
Type
Dropping Point,°C
ASTM D2265 150
Amber
2
Calcium/Lithium
>160
83 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
AVIATION LUBRICANTS LISTING BY APPLICATION
INDUSTRIAL
COMMERCIAL
PAGE
Grease
Mobil™ Aviation Grease SHC 100........................................... 85
Mobilgrease™ 28..................................................................... 85
Mobilgrease™ 33..................................................................... 85
Exxon HyJet™ IV-A Plus.......................................................... 85
Mobil Aero™ HFA..................................................................... 86
Jet Oil
Mobil Jet Oil™ II....................................................................... 86
Mobil Jet Oil™ 254................................................................... 86
Exxon™ Aviation Oil Elite 20W-50............................................ 86
MARINE
PRODUCT
PASSENGER
AVIATION LUBRICANTS
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
84
GREASES
Visit mobil.ca /pds for the most current product information
AVIATION LUBRICANTS
GREASE
Mobil™ Aviation Grease SHC 100 high performance
synthetic grease combines the unique features of
a polyalphaolefin (PAO) synthetic base fluid and
high quality lithium complex soap thickener system.
The thickeners deliver a high dropping point, excellent
resistance to water wash, and tenacious structural
stability. The synthetic base oil and select additives
provide outstanding protection against wear, rust,
corrosion, and high temperature degradation. The
wax-free properties of the base oil promote low
temperature mobility/pumpability and low starting and
running torque values. Traction property is considerably
lower than that of mineral oil, enabling temperature
reductions in the load zone of rolling element bearings.
Mobil Aviation Grease SHC 100 is the product of
choice for aircraft wheel bearing applications.
Viscosity, ASTM D445
Product
Colour
Mobil Aviation Grease SHC 100
cSt at
40°C
Red
cSt at
100°C
Dropping Point, °C 100
14.5
Mobilgrease™ 28 is a high performance, wide
temperature, anti-wear grease combining the unique
features of a polyalphaolefin (PAO) synthetic base fluid
with an organo-clay (non-soap) thickener. Consistency
is between an NLGI No. 1 and No. 2 grease, with
outstanding performance over a wide temperature
Water Washout, wt%
280
–
range. The wax-free nature of the synthetic base fluid,
together with its high viscosity index compared to mineral oils, provide excellent low temperature pumpability,
very low starting and running torque, and help reduce
operating temperatures in the load zone of rolling
element bearings.
Viscosity, ASTM D445
Product
Colour
Mobilgrease 28
Dark Red
cSt at
40°C
cSt at
100°C
Dropping Point, °C Water Washout, wt%
30
5.7
308
1
Mobilgrease™ 33 is a high performance lithiumcomplex grease designed for general purpose aircraft
use. Consistency is between NLGI grades 1 and 2.
Mobilgrease 33 utilizes a 100% polyalphaolefin base
oil and premium additives to help ensure outstanding
lubrication performance over a wide range of temperatures and operating conditions.
Viscosity, ASTM D445
Product
Colour
cSt at
40°C
Mobilgrease 33
12.5
Blue Green
cSt at
100°C
Dropping Point, °C 3.2
Kinematic Viscosity
Exxon HyJet IV-A Plus
Water Washout,
1 Hr at 79 ºC, wt%
1
6
246
Exxon HyJet™ IV-A Plus is a fire-resistant phosphate
ester hydraulic fluid for use in commercial aircraft. Our
best performing Type IV fluid approaches many of the
performance capabilities of Type V fluids, including
Product
Water Washout,
1 Hr at 38 ºC, wt%
high temperature stability, fluid life, low density and
rust protection. Meets specifications of all major aircraft
manufacturers and SAE AS1241.
cSt at
-53.9°C
cSt at
37.8°C
cSt at
98.9°C
cSt at
127.6°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Spec. Gravity
kg/l at 25ºC
1320
10.6
3.6
2.6
280
<-62
175
0.996
85 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
AVIATION LUBRICANTS
GREASE
Mobil Aero™ HFA is for aircraft systems requiring
hydrocarbon-based hydraulic fluids. This low viscosity
fluid contains shear-stable VI (viscosity index) improvers
Viscosity, ASTM D445 Spec. Gravity
cSt at
cSt at
V.I.
Pour Point,
Flash Point,
kg/l at 15.6ºC
40°C
100°C
ASTM D2270
°C, ASTM D97
ºC, COC, ASTM D92
ASTM D1298
Mobil Aero HFA
14.0
5.2
370
-60 max
93 min
COMMERCIAL
Product
for excellent low temperature performance, combined
with good anti-wear performance and chemical stability.
INDUSTRIAL
0.872
AVIATION LUBRICANTS
JET OIL
and oxidative stability to resist deterioration and
deposit formation in both the liquid and vapour phases,
as well as excellent resistance to foaming. Effective
operating range: -40 °C to 204 °C.
Viscosity, ASTM D445
Product
cSt at
40°C
cSt at
100°C
Pour Point,
°C, ASTM D97
Flash Point,
°C, ASTM D92
Mobil Jet Oil II
27.6
5.1
-59
270
Product
Mobil Jet Oil 254
Viscosity, ASTM D445
Spec. Gravity
cSt at
40°C
cSt at
100°C
Pour Point,
°C, ASTM D97
Flash Point,
ºC, COC, ASTM D92
kg/l at 15.6ºC
ASTM D1298
26.4
5.3
-62
254
1.0044
Product
Exxon Aviation Oil Elite 20W-50
Kinematic Viscosity
AVIATION
Exxon™ Aviation Oil Elite 20W-50 is a premium quality, semi-synthetic, ashless-dispersant aviation piston
engine oil. It is formulated with highly refined mineral
base oils combined with polyalphaolefin synthetic base
oil and ashless performance additives for outstanding
outstanding thermal and oxidation stability that resists
deterioration and deposit formation while maintaining
the physical characteristics required by builder and
military specifications. The physical properties of Mobil
Jet Oil 254 are similar to those currently available,
earlier-generation gas turbine lubricants. The effective
operating range is between -40°C and 232°C.
MARINE
Mobil Jet Oil™ 254 is a third-generation, extra high
performance, synthetic aircraft-type gas turbine lubricant engineered to meet the performance requirements
of gas turbine engines in commercial and military
aircraft. This product is formulated from a specially
prepared, hindered-ester base stock and fortified
with a unique chemical additive system. The result is
PASSENGER
Mobil Jet Oil™ II is a high performance aircraft-type
gas turbine lubricant formulated with a highly stable
synthetic base fluid and a unique chemical additive
system. This combination delivers outstanding thermal
engine cleanliness and protection from wear and
corrosion. This oil meets the requirements of all
opposed piston engine manufacturers across a
wide range of climatic conditions.
cSt at
40°C
cSt at
100°C
V.I.
ASTM D2270
Pour Point,
°C, ASTM D97
Flash Point,
ºC, COC, ASTM D92
180
16.3 min, 21.9 max
130
-27
258
Click Here to return to PRODUCT APPLICATION INDEX
86
GREASES
Visit mobil.ca /pds for the most current product information
QUESTIONS?
CALL OUR TECHNICAL SUPPORT CENTER AT
1 888 968-3776
mobilindustrial.com | mobildelvac.ca | mobil.ca
GREASE PRODUCT LISTING BY APPLICATION
Product
Brand
Product Brands vs
Thickener Type
Lith
– Lithium Complex
Polyrex – Polyurea
Centaur – Calcium Sulphonate
GreaseXHP 222Special
Product
Family
ISO/
NLGI
Identifier
(Moly/Application)
Temp – Clay
Lux
– Lithium
Grease – Multiple technologies
Identifier
Mobil Grease
Product
Families
Core Industrial Application
Product Families
Mobil SHCTM, Mobilgrease XHPTM
Select Specialty Industrial
Application Product Families
Mobil SHC PolyrexTM, Mobil PolyrexTM,
Mobil Centaur XHPTM
Moly content: Special – 0.75 or 1%; Moly – 3%; Mine – 5%
Core Commercial Vehicle Application
(On / Off Highway) Product Families
Mobil DelvacTM Xtreme, Mobilgrease XHPTM,
Mobil CentaurTM
Core Personal Vehicle Installer Greases
Mobil 1TM Synthetic Grease,
Mobilgrease XHPTM 222
MARINE
PASSENGER
ISO / NLGIThe first two numbers correspond to the first two
numbers of the base oil ISO Viscosity Grade (e.g. 220).
The last number corresponds to the NLGI grade.
COMMERCIAL
Decoding ManyMobil
Mobil Grease
Product Names
Master
Brand
INDUSTRIAL
Mobil Grease
Balanced Performance
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
88
GREASES
Visit mobil.ca /pds for the most current product information
GREASE PRODUCT LISTING BY APPLICATION
GREASEPRODUCT
PAGE
Agriculture Equipment
Automotive
Couplings
Mobilgrease XHP™ 220 Series.................................................97
Mobil Epic™ Series...................................................................98
Mobil Unirex™ EP Series..........................................................99
Mobil Delvac™ Xtreme Grease............................................... 100
Electric Motors
Environmentally Aware
Food Industry (NSF H-1) Gears – Enclosed, Semi-Fluid
Gears – Open High Temperature – Clay Thickened Mobil Polyrex™ EM...................................................................93
Mobil Unirex™ N.......................................................................93
Marine Mobil SHC Aware™ Grease EP 2.............................................96
Multi-Purpose Mobilith SHC™ Series..............................................................97
Mobilgrease XHP™ 220 Series.................................................97
Mobilgrease XHP™ 460 Series.................................................97
Mobil Centaur XHP™ 460 Series..............................................98
Mobilux™ EP Series.................................................................98
Mobil Epic™ Series...................................................................98
Mobil Unirex™ EP Series..........................................................99
Mobil™ Argon EP......................................................................99
Mobil™ Arcan 1.........................................................................99
Mobil 1™ Synthetic Grease.......................................................91
Mobil Ronex™ MP....................................................................91
Mobilgrease™ XTC...................................................................92
Mobilux™ EP 111......................................................................92
Mobil SHC™ Grease 100 EAL Series.......................................93
Mobil SHC Polyrex™ 462..........................................................94
Mobilgrease™ FM 101..............................................................94
Mobil Marvelube™ EP 9F.........................................................94
Nebula™ EP Special.................................................................94
Mobil Geargard™......................................................................95
Mobil Dynagear™ Series..........................................................95
Mobiltemp SHC™ 32.................................................................96
Mobiltemp™ Series...................................................................96
89 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
GREASEPRODUCT
PAGE
...........................................................................................
Off-Highway Heavy Duty Equipment
and On-Highway Trucking
Mobil Centaur™ Moly Series................................................... 100
Mobil Delvac™ Xtreme Grease............................................... 100
Mobilgrease XHP™ Mine........................................................ 100
Paper Machines
Pneumatic Tools / Air-line Lubricated
Railway Drilling
Specialty Synthetic
Mobilith SHC™ PM................................................................. 101
Mobil Centaur XHP™ 221....................................................... 101
Threads
Wind Turbines
Wire Ropes / Natural Core
Thredkote™ 706...................................................................... 103
Z-50 Pipe Dope....................................................................... 104
Mobil Arox™ NM 000.............................................................. 101
COMMERCIAL
INDUSTRIAL
GREASE PRODUCT LISTING BY APPLICATION
Arapen™ RB 320.................................................................... 102
Galena™ Tramo 3735............................................................. 102
Mobil SHC™ PF 462............................................................... 103
Mobil Beacon™ 325................................................................ 103
PASSENGER
DDR Grease............................................................................ 102
Mobil SHC™ Grease 460 WT................................................. 104
MARINE
Wire Rope Dressing................................................................ 104
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
90
GREASES
Visit mobil.ca /pds for the most current product information
GREASES
AUTOMOTIVE
Mobil 1™ Synthetic Grease is an NLGI No 2 high
performance automotive lubricant formulated with
synthetic base fluid, lithium complex soap thickener
and additives that deliver optimum extreme pressure
properties, excellent resistance to water wash and
outstanding protection against rust and corrosion.
The thickener system provides a high dropping point;
the synthetic base oil provides excellent performance at
high and low temperatures (-40°C to 150°C). Excellent
structural stability and high shear-stability make this an
outstanding automotive grease. It meets requirements
of the National Lubricating Grease Institute (NLGI)
performance classification GC-LB.
Colour,
NLGI
Soap
Product
ISO VG
Visual
Grade
Type
Mobil 1 Synthetic Grease
220
Red
2
Li-Complex
Mobil Ronex™ MP is a premium quality multipurpose
grease recommended for a wide range of automotive
and industrial applications. Formulated with a mineral
oil base fluid combined with a lithium complex soap
thickener and performance enhancing additives, this
lubricant delivers excellent performance over a wide
temperature range, including moderate load-carrying
Product
Viscosity, ASTM D445Water Washout,
cSt at
cSt at
Dropping Point,°C
ASTM D1264,
40°C
100°C
ASTM D2265
at 79°C, %
220
23.8
288
6
and extreme pressure properties. This grease resists
water, protects against corrosion and provides good
oxidation and thermal stability. Ronex MP is compatible
with most elastomer seal materials and meets
the requirements of the National Lubricating Grease
Institute (NLGI) performance classification GC-LB.
Viscosity, ASTM D445
cSt at 40°C
Colour,
Visual
NLGI
Grade
Thickener
Type
Dropping Point,°C
ASTM D2265 115
Green
2
Li-Complex
280
Mobil Ronex MP
Additional Automotive Grease
Mobilgrease XHP™ 220...........................................97
91 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
COUPLINGS
Product
Mobilgrease XTC
coupling lubrication and protection. The base oil and
extreme pressure (EP) / anti-wear (AW) additive
package work to reduce friction wear from sliding tooth
contact, deliver rust and corrosion protection, and high
temperature stability for this leading edge product.
Meets AGMA CG-1 and CG-2 coupling specifications.
Colour, Dropping Point,°C
Visual
Grade
Type
ASTM D2265
Dark Brown
1
Lithium
215
Viscosity, ASTM D445
cSt at 40°C 680
lubricant formulated with an extremely heavy (viscous)
mineral base oil. This NLGI 1 Grade grease is fortified
by an oil soluble molybdenum (Moly) additive and a
very effective corrosion inhibitor.
Mobilux EP 111
Lithium
Viscosity, ASTM D445
Colour,
NLGI
Thickener
Dropping Point,°C Product
Visual
Grade
Type
ASTM D2265 cSt at 100°C Black
1
180
45
Additional Couplings Grease
Mobil Unirex™ EP Series.........................................99
PASSENGER
Mobilux™ EP 111 is an high performance grease
primarily designed for AGMA CG-3 couplings. It is
specifically formulated to help protect against wear,
even in heavily loaded misaligned low speed gear
couplings. Mobilux EP 111 is a lithium hydroxystearate
COMMERCIAL
Mobilgrease™ XTC is an high performance product
designed for high speed coupling applications. Formulated with a high viscosity mineral base oil and
an extremely effective, heavy duty additive package,
this lubricant provides low bleed as well as high
temperature stability, properties critical to modern
INDUSTRIAL
GREASES
MARINE
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
92
GREASES
Visit mobil.ca /pds for the most current product information
GREASES
ELECTRIC MOTORS
Mobil Polyrex™ EM premium grease is specially
formulated for electric motor bearings. Outstanding
grease life promotes long-life, high temperature
lubrication of ball and roller bearings for long electric
Colour,
NLGI
Product
Visual
Grade
Mobil Polyrex EM
Blue
2
motor life. The advanced polyurea thickener formulation delivers increased durability versus conventional
polyurea greases when subjected to mechanical
shear forces.
Viscosity, ASTM D445
cSt at
cSt at
Base Oil V.I.,
Dropping Point,°C
40°C
100°C
ASTM D2270
ASTM D2265
115
Mobil Unirex™ N greases are premium quality, lithium
complex products suitable for high temperature service
in rolling element bearings. The lithium complex thickener resists softening and running out of bearings at
12.2
Green
Green
2
3
260
temperatures up to 190°C. These versatile greases
are recommended for a wide range of industrial
applications and are particularly well suited for electric
motor lubrication.
Colour,
NLGI
Thickener Viscosity, ASTM D445
Product
Visual
Grade
Type cSt at 40°C Mobil Unirex N 2
Mobil Unirex N 3
95
Li-Complex
Li-Complex
115
115
Base Oil V.I.,
ASTM D2270
Dropping Point,°C
ASTM D2265
95
95
280
235
Additional Electric Motor Grease
Mobilith SHC™ Series............................................ 97
GREASES
ENVIRONMENTALLY AWARE
Mobil SHC™ Grease 100 EAL Series are high
performance greases designed specifically for environmentally sensitive applications. These virtually non-toxic
greases are formulated from a biodegradable synthetic
ester base oil and a lithium soap thickener. The wax-free
Product
Mobil SHC Grease 101 EAL
Mobil SHC Grease 102 EAL
nature of the synthetic base fluid, together with its low
traction coefficient, delivers excellent low temperature
pumpability and very low starting and running torque –
a significant benefit since many environmentally sensitive applications are located outdoors.
Base Oil
ISO VG
Colour,
Visual
NLGI
Grade
Thickener
Type
Dropping Point,°C ASTM D2265
Water Washout, at 79°C,
ASTM D1264, Wt. %
100
100
Tan
Tan
1
2
Lithium
Lithium
180
180
8.0
6.5
93 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
FOOD INDUSTRY (NSF H-1)
To obtain the current ‘Reference Listing of Accepted Construction Materials,
Packaging Materials and Non-Food Chemical Products’ (including lubricants),
please visit the Canadian Food Inspection Agency (CFIA) website.
NLGI
Product
Grade
Thickener
Type
Mobil SHC Polyrex 462
Polyurea
2
highly resistant to water and has excellent corrosion
protection for equipment in wet, humid environments
and applications where water wash downs are frequent.
It resists oxidation and loss of structural stability, often
enhancing productivity by enabling lubrication intervals
to be safely extended.
Viscosity, ASTM D445
40°C,
100°C,
Dropping Point,°C cSt
cSt
ASTM D2265
460
40
Product
Mobilgrease FM 101
270
Water Spray-Off
ASTM D4049,
% Weight Loss
5
30
Chapter 21, and is NSF registered as an H1 classified
lubricant. It is manufactured in facilities registered to
the requirements of ISO 21469, helping to ensure that
the highest levels of product integrity are maintained.
Colour,
Visual
NLGI
Grade
Thickener
Type
Dropping Point,°C
ASTM D2265
Viscosity, ASTM D445
cSt at 40°C White
1
Aluminum Complex
260
100
PASSENGER
Mobilgrease™ FM 101 is a high performance multi-purpose grease designed specifically for food processing
machinery. Mobilgrease FM 101 is formulated with components meeting the requirements of CFR 178.3570,
Water Washout,
79°C, ASTM D1264,
% Weight Loss
COMMERCIAL
Mobil SHC Polyrex™ 462 is a unique combination
of synthetic oil, polymer enhancement and a balanced
additive system designed to bring solutions to tough
lubrication problems. Formulated with advanced
Polyurea thickener technology, this advanced lubricant
provides high temperature performance while carrying
a full NSF H1 registration. Mobil SHC Polyrex 462 is
INDUSTRIAL
GREASES
GREASES
Mobil Marvelube™ EP 9F is widely used in industrial
and automotive applications requiring economical
lubrication under moderate service conditions. This
water-resistant grease works well over an operating
temperature range of -30°C to 50°C. Extreme pressure
Product
Colour,
Visual
Marvelube EP 9F
Amber
properties provide good film strength and resistance
to wear. Marvelube EP 9F is suitable for steering
gearboxes, gear cases of hand tools, chain drives and
centralized grease dispensing equipment.
Base Oil Viscosity
Thickener
Type Structure
cSt at 40°C
Calcium 57.0
AVIATION
Nebula™ EP Special is recommended for heavily
loaded worm gear reducers or enclosed gear
units whose design or worn seals may cause
excessive leakage with conventional gear oils.
Semi-fluid This product is specifically recommended for
underground mining equipment in severe service.
Excellent anti-rust properties help protect equipment
subjected to water contamination.
Product
Colour,
Visual
Thickener Type
Nebula EP Special Amber
Calcium Sulphonate
Base Oil Viscosity
cSt at 40°C
100
Visit mobil.ca /pds for the most current product information
Mobilux EP™ 023......................................................98
Click Here to return to PRODUCT APPLICATION INDEX
94
GREASES
Additional Semi-Fluid Greases
Mobilith SHC™ Series..............................................97
MARINE
GEARS – ENCLOSED, SEMI-FLUID
GREASES
GEARS – OPEN
Mobil Geargard™ is a high performance, semisynthetic lubricant designed for use on open gears in
grinding mills (rod, ball and SAG). A high flash point
non-chlorinated diluent facilitates dispensing through
typical mill auto-greasing systems. The solvent is
designed to evaporate after application, leaving an
adhesive and cohesive high viscosity lubricating film.
Potent additives provide extreme pressure (EP)
protection and excellent control of rust and corrosion.
Viscosity, ASTM D445
cSt at 40°C
cSt at 100°C
with diluent
w/o diluent Colour,
Flash Point,°C
Product
Visual
Structure
with diluent
Mobil Geargard
Black
Smooth
Mobil Dynagear™ Series premium performance open
gear lubricants provide outstanding protection of heavily loaded open gear sets exposed to a wide range of
operating conditions. Formulated with lithium thickener
technology, high performance additives and high
Product
Mobil Dynagear 600 SL
Mobil Dynagear 800 Extra
Mobil Dynagear 2000
Mobil Dynagear 4000
Colour,
Visual
NLGI
Grade
Thickener
Type
Black
Black
Black
Black
1
0
0 to 00
00
Lithium
Lithium
Lithium
Lithium
110
5000
1500
viscosity semi-synthetic base fluids, these lubricants
synergistically provide a protective film that adheres
tenaciously. Mobil Dynagear Series gear lubricants
provide excellent dispensability without the use of
chlorinated or hydrocarbon solvents.
Molybdenum
Disulphide, Wt. %,
Structure
95 Visit mobil.ca /pds for the most current product information
>2.0
>2.0
>2.0
>2.0
Dropping Point,°C Viscosity, ASTM D445
ASTM D2265
cSt at 40°C
Smooth
Smooth, Semi-fluid
Smooth, Semi-fluid
Smooth, Semi-fluid
175
198
193
213
620
680
2000
4000
Click Here to return to PRODUCT APPLICATION INDEX
GREASES
HIGH TEMPERATURE – CLAY THICKENED
stability and a high dropping point, for outstanding
high temperature protection. The wax-free synthetic
base fluids with their high viscosity index also provide
outstanding lubrication at low temperatures.
Product
Mobiltemp SHC 32
Colour,
Visual
NLGI
Grade
Thickener
Type
Dropping Point,°C
ASTM D2265
Viscosity, ASTM D445
cSt at 40°C Red
1.5
Clay
260+
32
mineral oil and specially formulated to provide low
volatility and excellent resistance to oxidation at high
temperatures, along with resistance to water washout
and good anti-wear performance under heavy loads
and low speeds. Mobiltemp 78 also contains molybdenum disulphide (Moly) for added anti-wear protection.
Product
Mobiltemp 2
Mobiltemp 78
Colour,
Visual
NLGI
Grade
Thickener
Type
Dropping Point,°C
ASTM D2265
Viscosity, ASTM D445
cSt at 40°C Amber
Grey-black
2
1
Clay
Clay
300
300
460
460
PASSENGER
Mobiltemp™ Series greases are high performance
clay-thickened products designed for plain and antifriction bearings operating at low speed and high temperature or under cycling conditions from ambient to high
temperatures. The clay thickener, unlike traditional soap
thickeners, does not soften at high temperatures. These
greases are based on a high quality, high viscosity
COMMERCIAL
Mobiltemp SHC™ 32 is a high performance anti-wear
grease primarily intended for high temperature applications. Synthetic base oils deliver excellent resistance
to thermal/oxidative degradation. The organo-clay nonsoap thickener provides high temperature structural
INDUSTRIAL
GREASES
Mobil SHC Aware™ Grease EP 2 is a high performance synthetic grease designed specifically for applications which are environmentally sensitive and meets
the requirements of the U.S. Environmental Protection
Agency (EPA) 2013 Vessel General Permit (VGP). This
leading product is readily biodegradable and virtually
non-toxic grease and is formulated based on biodegradable saturated ester base oils and a lithium/calcium
soap thickener. It does not emulsify and has excellent
water wash and salt water corrosion resistance.
Product
Colour,
Visual
NLGI
Grade
Thickener
Type
Dropping Point,°C
ASTM D2265
Viscosity, ASTM D445
cSt at 40°C
Mobil SHC Aware Grease EP 2
Amber
2
Calcium/Lithium
>160
150
MARINE
MARINE
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
96
GREASES
Visit mobil.ca /pds for the most current product information
GREASES
MULTI-PURPOSE
Mobilith SHC™ Series greases are high performance
products designed for a wide variety of applications
at temperature extremes. They combine the unique
features of synthetic base fluids with those of a high
quality lithium complex thickener. The wax-free nature
of synthetic fluids and the low coefficient of traction
(compared with mineral oils) provide excellent low
temperature pumpability and very low starting and
running torque. These products offer the potential for
energy savings and can reduce operating temperatures
in the load zone of spherical roller and ball bearings.
The lithium complex thickener contributes excellent
adhesion, structural stability and resistance to water.
The greases have a high level of chemical stability
and are formulated with special additive combinations
to deliver excellent protection against wear, rust and
corrosion, and to provide operating viscosity at high
and low temperatures.
Viscosity, ASTM D445
Colour,NLGI Thickener
Dropping Point,°C Product
Visual
Grade
Type
cSt at 40°C
ASTM D2265
Mobilith SHC 007
Mobilith SHC 100
Mobilith SHC 220
Mobilith SHC 460
Mobilith SHC 1500
Red
Red
Red
Red
Red
00
2
2
1.5
1.5
Li-Complex
Li-Complex
Li-Complex
Li-Complex
Li-Complex
Mobilgrease XHP™ 220 Series greases are intended
for a wide variety of applications and severe operating
conditions. These extended service lithium complex
greases were designed to outperform our conventional
products through cutting edge, proprietary, lithium
complex manufacturing technology. They deliver
excellent high temperature performance with superb
Product
Mobilgrease XHP 221
Mobilgrease XHP 222
Mobilgrease XHP 222 Special
Mobilgrease XHP 461
Mobilgrease XHP 462
Mobilgrease XHP 462 Moly
–
265
265
265
265
Dark Blue
Dark Blue
Grey-Black
1
2
2
Li-Complex
Li-Complex
Li-Complex
–
–
0.75
220
220
220
1
2
2
Dropping Point,°C
ASTM D2265
280
280
280
chemical stability and offer excellent protection
against rust and corrosion. These greases feature
high dropping points and a maximum recommended
operating temperature of 140°C. Mobilgrease
XHP 462 Moly is fortified with 3% molybdenum
disulphide to provide enhanced EP (extreme pressure)
and AW (anti-wear) protection in heavily loaded
and high sliding applications.
Viscosity, ASTM D445
Colour, NLGIThickener Molybdenum
Visual
Grade
Type
Disulphide, Wt. %
cSt at 40°C
Dark Blue
Dark Blue
Grey
–
6
3
3
2.5
adhesion, structural stability and resistance to water
contamination. These greases have a high level of
chemical stability and offer excellent protection against
rust and corrosion. They feature high dropping points
and a maximum recommended operating temperature
of 140°C. Base oil viscosity is ISO VG 220.
Viscosity, ASTM D445
Colour, NLGIThickener Molybdenum
Visual
Grade
Type
Disulphide, Wt. %
cSt at 40°C
Mobilgrease XHP™ 460 Series greases are intended
for a wide variety of heavy duty applications and
operating conditions. These extended service lithium
complex greases were designed to outperform our
conventional products through cutting edge, proprietary,
lithium complex manufacturing technology. They deliver
excellent high temperature performance with superb
adhesion, structural stability and resistance to water
contamination. These greases have a high level of
Product
460
100
220
460
1500
Water Washout,
ASTM D1264,
79°C, % Wt. Loss
Li-Complex
Li-Complex
Li-Complex
97 Visit mobil.ca /pds for the most current product information
–
–
3
460
460
460
Dropping Point,°C
ASTM D2265
280
280
280
Click Here to return to PRODUCT APPLICATION INDEX
GREASES
MULTI-PURPOSE
water saturated environments, providing rust protection
between long re-lubrication intervals. The inherent
EP properties exhibit great stability in the presence of
water, providing a balance between wear protection
and resistance to corrosion.
Water Washout,
Colour,NLGI ThickenerViscosity, ASTM D445 Dropping Point,°C ASTM D1264,
Product
Visual
Grade
Type
cSt at 40°C
ASTM D2265
1 hr. at 79°C, %
Mobil Centaur XHP 461
Mobil Centaur XHP 462
Amber
Amber
1
2
Calcium Sulphonate
Calcium Sulphonate
Mobilux™ EP Series lithium hydroxystearate greases
are formulated to deliver extra protection against wear,
rusting and water washout. They are particularly well
460
460
275
275
Water Spray
Resistance,
ASTM D4049, mass %
1.0
0.5
25
20
suited for applications in moist or wet conditions.
Mobilux EP Series includes one general purpose
grease and one special duty semi-fluid lubricant.
Colour,
Visual
NLGI
Grade
Thickener
Type
Dropping Point,°C
ASTM D2265
Viscosity, ASTM D445
cSt at 40°C
Mobilux EP 2
Mobilux EP 023
Brown
Brown
2
000
Lithium
Lithium
190
–
160
320
under load. Epic MQ is particularly recommended for
centralized lubrication systems in open-pit mining, as
well as severe-service, low temperature applications in
forestry and construction. It is fortified with 5 percent
molybdenum disulphide, as required by some equipment manufacturers. Epic greases have a long history
of excellent performance in the toughest applications
and under extreme temperature conditions.
Mobil Epic EP 102
Mobil Epic EP Moly
Mobil Epic MQ
Red
Grey-Black
Grey-Black
1.5
1.5
0.5
Li-Complex
Li-Complex
Li-Complex
0
3
5
Dropping Point,°C
ASTM D2265
Viscosity, ASTM D445
cSt at 40°C
260
260
230
130
130
60
MARINE
Molybdenum
Colour, NLGIThickenerDisulphide
Product
Visual
Grade
Type
Content, Wt. %
PASSENGER
Product
Mobil Epic™ Series are premium quality, semi-synthetic all-weather greases that deliver excellent lubrication and wear protection at temperatures as low as
-50°C and as high as 150°C. They are recommended
for multi-service applications in plain and anti-friction
bearings, gears, slides and other situations where
friction reduction and low wear are required. Epic
EP Moly offers additional protection in applications
involving heavy loads or slow reciprocating motion
COMMERCIAL
Mobil Centaur XHP™ 460 Series is a premium family
of greases formulated with advanced calcium sulphonate thickener technology, which carries both inherent
rust protection and extreme pressure (EP) properties.
Relative to conventional soap-base thickeners (lithium,
aluminum, calcium), calcium sulphonate excels in
INDUSTRIAL
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
98
GREASES
Visit mobil.ca /pds for the most current product information
GREASES
MULTI-PURPOSE
Mobil Unirex™ EP Series are extremely versatile
long-life premium performance greases. Their unique
formulation protects equipment over a very wide
temperature range. Unirex greases are shear and
oxidation stable, protect against rust and corrosion
and resist softening at elevated temperatures. Unirex
Lotemp EP is recommended for winter conditions
that require low operating or dispensing limits. Unirex
Lotemp Moly and Unirex EP 1 Moly offer performance
Product
Mobil Unirex EP 0
Mobil Unirex EP 1
Mobil Unirex EP 2
Mobil Unirex EP 0 Moly
Mobil Unirex EP 1 Moly
Mobil Unirex Lotemp EP
Mobil Unirex Lotemp Moly
Colour,
Visual
NLGI
Grade
Thickener
Type
Operating Temp.
Range,°C
Dropping Point,°C
ASTM D2265
Viscosity, ASTM D445
cSt at 40°C
Green
Green
Green
Grey-Black
Grey-Black
Green
Grey-Black
0.5
1
2
0.5
1
1.5
1.5
Li-Complex
Li-Complex
Li-Complex
Li-Complex
Li-Complex
Li-Complex
Li-Complex
-35 to 110
-30 to 160
-30 to 160
-35 to 110
-30 to 150
-55 to 110
-55 to 110
190
280
300
190
280
260
260
68
220
220
68
220
10
10
Mobil™ Argon EP greases are high quality, shear
stable products suitable for use in both plain and
anti-friction bearings lubricated by an automatic
centralized dispensing system. Argon EP greases are
widely used to lubricate mining equipment, bolt and nut
formers, vane spindles of hydraulic turbines and a wide
range of other machinery serviced by automatic dis
Product
Mobil Argon EP 0 Mobil Argon EP 1 Mobil Arcan 1
pensing equipment. They are useful over an operating
temperature range of 0°C to 95°C. Argon EP 1 is an
excellent choice for severe roller bearing service calling
for an NLGI No.1 grease. Argon EP greases contain
an extreme pressure additive, have a 21 kg Timken OK
Load and are recommended where bearings are shock
loaded or operating under heavy load conditions.
NLGI
Grade
Thickener
Type
Dropping Point,°C
ASTM D2265
0
1
Calcium
Calcium
135
135
Mobil™ Arcan 1 is a white filler-type grease widely
used in bearings and mechanisms to combat severe
water contamination. This grease has good adhesion
to metal under wet conditions; it stays in place and
maintains a lubricating film to protect metal surfaces
from corrosion for extended intervals. As a result,
Product
characteristics similar to Unirex Lotemp EP and Unirex
EP 1 greases respectively; each adds the extreme
pressure protection of molybdenum disulphide (Moly).
Unirex greases meet the challenges of demanding
applications in such industries as transportation,
manufacturing, construction, mining, logging, cement,
marine and paper-making, where grease must perform
well in a multitude of severe applications.
Viscosity, ASTM D445
cSt at 40°C
175
175
Arcan 1 is well suited to such applications as printing
machines, laundry and dry cleaning equipment and
lubrication of office equipment. It is not recommended
for wheel bearings, electric motor bearings or other
high speed, grease packed anti-friction bearings.
Operating temperature range is -5°C to 110°C.
Colour,
Visual
NLGI
Grade
Thickener
Type
Dropping Point,°C
ASTM D2265
White
1
Lithium
185
99 Visit mobil.ca /pds for the most current product information
Viscosity, ASTM D445
cSt at 40°C cSt at 100°C
100.0
10.0
Click Here to return to PRODUCT APPLICATION INDEX
GREASES
OFF-HIGHWAY HEAVY DUTY EQUIPMENT AND ON-HIGHWAY TRUCKING
Fortified with 3% molybdenum disulphide (Moly) to
complement a robust extreme pressure (EP) additive
system, these greases are particularly well suited to
the demanding requirements of heavy duty truck
chassis, construction and mining equipment, and
heavily load industrial bearings.
Water Spray
Molybdenum Water Washout, Resistance,
Colour, NLGI
Thickener
Disulphide, Viscosity, ASTM D445 Dropping Point,°C ASTM D1264, ASTM D4049, Product
Visual Grade
Type
Wt. %
cSt at 40°C
ASTM D2265
1 Hr at 79°C, %
mass %
Mobil Centaur Moly 1
Mobil Centaur Moly 2
Grey
Grey
1
2
Calcium Sulphonate
Calcium Sulphonate
3
3
288
280
Orange
2
Li-Complex
Colour, NLGI
Thickener
Product
Visual
Grade
Type
Mobilgrease XHP 100 Mine
Mobilgrease XHP 320 Mine
Mobilgrease XHP 321 Mine
Mobilgrease XHP 322 Mine
Gray-Black
Gray-Black
Gray-Black
Gray-Black
0
0
1
2
Li-Complex
Li-Complex
Li-Complex
Li-Complex
320
Water Washout,
ASTM D1264,
1 Hr at 79°C, % 260
6
harsh conditions. They deliver superior performance
in bucket pins, pivot pins and heavily loaded chassis
components. Mobilgrease XHP 100 Mine and 320 Mine
are especially well suited for central lubrication systems
in mining and other off-highway equipment requiring an
NLGI 0 Grade grease.
Water Washout, Water Sprayoff,
Molybdenum Viscosity, ASTM D445 Dropping Point,°C ASTM D1264, ASTM D4049, Disulphide, Wt. %
cSt at 40°C
ASTM D2265
79°C, % Loss
% Loss
5
5
5
5
100
320
320
320
200
270
270
270
–
–
10
2
–
–
28
16
AVIATION
Additional Off-Highway Heavy Duty Equipment and On-Highway Trucking Greases
Mobilgrease XHP™ 220 Series................................ 97
Mobilgrease XHP™ 460 Series................................ 97
Mobil Centaur XHP™ 460 Series............................. 98
Mobil Epic™ Series.................................................. 98
Mobil Unirex™ EP Series......................................... 99
Click Here to return to PRODUCT APPLICATION INDEX
100
GREASES
Visit mobil.ca /pds for the most current product information
MARINE
Mobilgrease XHP™ Mine lubricants are specifically
designed for extra heavy duty off-highway and mining
equipment. These greases have excellent extreme
pressure and anti-wear properties, along with exceptional adhesion, very good resistance to water washout
and spray-off, with extended service capabilities under
25
20
U-joints, and fifth wheels. It is also recommended
for plain and anti-friction bearings in construction
and mining vehicles operating in severe service
and weather conditions. It is also recommended for
heavily loaded industrial bearings. Recommended
temperature range: -20°C to +175°C.
Colour, NLGIThickenerViscosity, ASTM D445 Dropping Point,°C Product
Visual
Grade
Type
cSt at 40°C
ASTM D2265
Mobil Delvac Xtreme Grease
1.0
1.0
PASSENGER
Mobil Delvac™ Xtreme Grease is an high performance extreme pressure lubricant. It exhibits excellent
resistance to softening and provides good adhesion
and cohesion, protection against wear and shock loads,
and resistance to high temperature oxidation and rust.
Mobil Delvac Xtreme Grease is recommended for use
in heavy duty trucks, especially hinge and bucket pins,
320
320
COMMERCIAL
Mobil Centaur™ Moly Series are premium quality
greases formulated with advanced calcium sulphonate
thickener technology. Unlike conventional soap-base
thickeners (lithium, aluminum, calcium), calcium
sulphonate delivers outstanding resistance against the
effects of water washout, water spray-off and corrosion.
INDUSTRIAL
GREASES
PAPER MACHINES
Mobilith SHC™ PM high performance greases are
designed specifically for severe-service paper machine
applications, including those in extreme temperature
environments with exposure to different qualities of
water. These lubricants combine the unique features
of a synthetic base fluid with a high quality lithium
complex thickener. The wax-free synthetic base fluid
delivers excellent low temperature pumpability and
low starting and running torque when compared to
non-synthetic oil products of the same viscosity; its
high viscosity index ensures excellent film protection
at high temperatures. The lithium complex thickener
contributes excellent adhesion, structural stability
and enhanced resistance to water. A special additive
system resists rust, corrosion and oxidation and helps
protect against wear.
Viscosity, ASTM D445 Dropping Point,°C Colour, NLGIThickener
Product
Visual
Grade
Type
cSt at 40°C
ASTM D2265
Mobilith SHC PM 220
Mobilith SHC PM 460
Off-White
Off-White
1.5
1.5
Li-Complex
Li-Complex
Mobil Centaur XHP™ 221 is recommended for
rolling element bearings in machinery operating at
high temperatures where resistance to water washing
and corrosion is important. Such applications include
220
460
275
275
Water Washout,
ASTM D1264,
79°C, % Loss
2
3
wet-end paper machine bearings and heavily loaded
industrial ball and roller bearings, including those in
steel mills and mining.
Water Washout
Colour,NLGI
Thickener Viscosity, ASTM D445 Dropping Point,°C
at 79°C ASTM D,
Product
Visual
Grade
Type
cSt at 40°C
ASTM D2265
1264, Wt. % Mobil Centaur XHP 221
Brown
1.5
Calcium Sulphonate Complex
220
318
1
Additional Paper Machine Greases
Mobilgrease XHP™ 460 Series............................. 97
Mobil Unirex™ EP Series...................................... 99
GREASES
PNEUMATIC TOOLS/AIR-LINE LUBRICATED
Mobil Arox™ NM 000 is an extreme pressure,
semi-fluid grease designed specifically to provide a
mist-free, non-toxic environment for air-line lubricated
pneumatic tools, including rock drills, jackhammers,
drifters, wagon drills, chippers, tampers, riveters,
impact tools and pavement breakers. Low-odour,
friction-and-wear-reducing additives also have emulsifying properties and help protect metal surfaces from
corrosion and rust.
Product
Viscosity, ASTM D445
Colour, NLGIThickener
Visual
Grade
Type
cSt at 40°C
Arox NM 000
Amber
000
101 Visit mobil.ca /pds for the most current product information
Calcium
140
Click Here to return to PRODUCT APPLICATION INDEX
GREASES
RAILWAY
Product
Arapen RB 320
withstand shear, i.e. retain consistency after prolonged
working, as in the churning action of an anti-friction
bearing. Arapen RB 320 maintains good seal performance, a significant requirement for shop-to-shop
wheel service. It also resists heat, rust and structural
change in the presence of water.
Colour,
Visual
NLGI
Grade
Thickener
Type
Dropping Point,°C
ASTM D2265
Viscosity, ASTM D445
cSt at 100°C
Light Amber
1.5
Calcium-Lithium
180
14.7
Galena™ Tramo 3735 is a sulphur-phosphorus
extreme pressure traction-motor gear lubricant
designed for all locomotives, including the newest,
high horsepower per axle units. It delivers excellent
protection in severe temperatures, summer and
winter, for effective all-season lubrication.
Viscosity, ASTM D445
Colour,Thickener
Visual
Type
cSt at 100°C
Product
Black
Lithium
200.0
PASSENGER
Galena Tramo 3735
COMMERCIAL
Arapen™ RB 320 is a long-life grease developed for
the roller bearings of railroad car journals where no
provision is made for in-service relubrication. It has
high oxidation stability and is highly resistant to chemical deterioration that might produce acids or deposits
detrimental to bearing life. It has exceptional ability to
INDUSTRIAL
GREASES
DRILLING
Product
DDR Grease
At the same time, drill rods and joints may be washed
by the sludge water used to force rock particulate
upwards from the hole. DDR Grease is recommended
for lubrication of diamond drill rods, on the surface or
underground. It is normally applied by brush or hand
and smeared over the drill rods where they are stacked.
Colour,
Visual
NLGI
Grade
Thickener
Type
Dropping Point,°C
ASTM D2265
Viscosity, ASTM D445
cSt at 40°C
Tan
3
Barium Complex
170
320.0
MARINE
DDR Grease is a very tacky and adhesive lubricating
grease, formulated to stay in place in severe-service
diamond drilling operations. The primary function of
a drill rod grease is to reduce friction of the drill rod
against the walls of the hole. This can be a considerable
task when long lengths of pipe weave in the drill hole.
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
102
GREASES
Visit mobil.ca /pds for the most current product information
GREASES
SPECIALTY SYNTHETIC
Mobil SHC™ PF 462 grease is a long-life, severeservice lubricant for bearings, valves, seals and other
applications requiring oxidation stability and lubrication
performance at high temperatures. Formulated with perfluoropolyether thickened with polytetrafluoroethylene,
Viscosity, ASTM D445
cSt at
cSt at
Dropping Point,°C 40°C
100°C
ASTM D2265
NLGI
Product
Grade
Mobil SHC PF 462
2
440
42
Mobil Beacon 325
Water Washout,
79°C, ASTM D1264,
% Loss
258
Mobil Beacon™ 325 is a high performance grease
specifically formulated for precision equipment operating at moderate and low temperatures. Formulated
with a synthetic base oil of extremely low viscosity and
low volatility plus a lithium soap thickener, Beacon 325
delivers good mechanical stability, high resistance to
Product
Mobil SHC PF 462 provides dependable performance
up to 240˚ C and has excellent lubricity, corrosion
resistance, thermal and oxidative stability and
chemical inertness.
0.94
Water Spray-Off,
ASTM D4049,
% Weight Loss
5
water and extremely high oxidation stability. As the
base oil viscosity is low and the viscosity index of the
fluid is high, the grease has excellent low temperature
properties, including low starting and running torque
at very cold temperatures and good pumpability.
Colour,
Visual
NLGI
Grade
Thickener
Type
Dropping Point,°C
ASTM D2265
Viscosity, ASTM D445
cSt at 40°C
Tan
2
Lithium
180
12
GREASES
THREADS
Thredkote™ 706 is a simple soap grease containing
graphite and metallic fillers such as lead, zinc and
copper. It is designed for the lubrication of threads on
casings, tubing and line joints in the oil drilling industry
and has been used successfully in Canada for many
years. It is also used in the connection of high pressure
steam lines and non-potable water lines.
Penetration,
Viscosity, ASTM D445
Colour,NLGI
mm/10 @ 25°C
Product
Visual
Grade
Dropping Point,°C
cSt at 40°C
% Graphite
worked 60 strokes Thredkote 706
–
1
91
103 Visit mobil.ca /pds for the most current product information
–
18
330
Click Here to return to PRODUCT APPLICATION INDEX
GREASES
THREADS
Product
Z-50 Pipe Dope
Z-50 Pipe Dope is recommended for bolts, nuts and
threaded fittings where tightness of the joint and ease
of removal are desired. This product meets or exceeds
the requirements of API recommended practice 7A1
for Rotary Shouldered Connection Thread Compounds.
Its operating temperature range is -15°C to 150°C.
Colour,
Visual
NLGI
Grade
Dropping Point,°C
ASTM D2265
Viscosity, ASTM D445
cSt at 40°C
Grey-Black
1
91
12
GREASES
Mobil SHC™ Grease 460 WT is a high performance
product especially suited to meet or exceed the
demanding requirements of wind turbine applications
at temperature extremes. The wax-free nature of
the synthetic base fluids and their low coefficient of
traction provide excellent low temperature pumpability
and very low starting and running torque. The lithium
complex thickener contributes excellent adhesion,
structural stability and resistance to water. The grease
has a high level of chemical stability. Special additive
combinations provide excellent protection against wear,
rust and corrosion at high and low temperatures.
Water Washout,
Viscosity, ASTM D445 Dropping Point,°C
Colour, NLGIThickener
ASTM D1264,
Product
Visual
Grade
Type
cSt at 40°C
ASTM D2265
Loss at 79°C, % wt
1.5
Li-Complex
460
255
10
MARINE
Red
PASSENGER
WIND TURBINES
Mobil SHC Grease 460 WT
COMMERCIAL
Z-50 Pipe Dope is an anti-seize compound recommended for a wide variety of applications. In oil field
operations, it is used on the threads of new drill pipe
and can also be applied as a sealing compound
on the threads of semi-permanent joints, as when
casing is set. In automotive and industrial applications,
INDUSTRIAL
GREASES
WIRE ROPES
Product
Wire Rope Dressing
Colour,
Visual
Structure
Black
Smooth
Thickener
Type
Dropping Point,°C
ASTM D2265
Lithium
205
Viscosity, ASTM D445
cSt at 40°C
320 Click Here to return to PRODUCT APPLICATION INDEX
104
GREASES
Visit mobil.ca /pds for the most current product information
is formulated with non-asphaltic mineral base stocks,
which minimize peeling, cracking and flaking off in cold
weather. It contains molybdenum disulphide and solid
graphite lubricant as well as additives to resist water
and protect wire rope from rust and corrosion.
AVIATION
Wire Rope Dressing is an all-season, multi-purpose
lubricant for hoist drum wire ropes in underground
mining, dragline or electro-mechanical shovel operations. At ambient temperatures between -40°C and
50°C, wire ropes are protected by a tenacious film
that adheres firmly to the rope. Wire Rope Dressing
APPENDICES
Temperature Conversion Table
Locate in the centre column of the three columns the temperature in °C or °F to be converted.
For given Celsius temperatures, read Fahrenheit equivalent in the left-hand column. For given
Fahrenheit temperatures, read the Celsius equivalent in the right-hand column.
Examples:
a. Given -30°C; convert to Fahrenheit. Locate -30 in the centre column; read -22.0°F
in the left-hand column.
b. Given -30°F; convert to Celsius. Locate -30 in the centre column; read -34.4°C
in the right-hand column.
For temperatures not shown, interpolate from the values listed or use the
following equations:
°C = (°F - 32) x 5
°F = °C x 9 + 32
9 5
To °F
From °C or °F
To °C
To °F
From °C or °F
To °C
To °F
-148.0
-130.0
-112.0
-94.0
-76.0
-58.0
-54.4
-50.8
-47.2
-43.6
-40.0
-36.4
-32.8
-29.2
-25.6
-22.0
-18.4
-14.8
-11.2
-7.6
-4.0
-0.4
+3.2
+6.8
+10.4
+14.0
+15.8
+17.6
+19.4
+21.2
-100
-90
-80
-70
-60
-50
-48
-46
-44
-42
-40
-38
-36
-34
-32
-30
-28
-26
-24
-22
-20
-18
-16
-14
-12
-10
-9
-8
-7
-6
-73.3
-67.8
-62.2
-56.7
-51.1
-45.6
-44.4
-43.3
-42.2
-41.1
-40.0
-38.9
-37.8
-36.7
-35.6
-34.4
-33.3
-32.2
-31.1
-30.0
-28.9
-27.8
-26.7
-25.6
-24.4
-23.3
-22.8
-22.2
-21.7
-21.1
+23.0
+24.8
+26.6
+28.4
+30.2
+32.0
+33.3
+35.6
+37.4
+39.2
+41.0
+42.8
+44.6
+46.4
+48.2
+50.0
+51.8
+53.6
+55.4
+57.2
+59.0
+60.8
+62.6
+64.4
+66.2
+68.0
+69.8
+71.6
+73.4
+75.2
-5
-4
-3
-2
-1
0
+1
+2
+3
+4
+5
+6
+7
+8
+9
+10
+11
+12
+13
+14
+15
+16
+17
+18
+19
+20
+21
+22
+23
+24
-20.6
-20.0
-19.4
-18.9
-18.3
-17.8
-17.2
-16.7
-16.1
-15.6
-15.0
-14.4
-13.9
-13.3
-12.8
-12.2
-11.7
-11.1
-10.6
-10.0
-9.4
-8.9
-8.3
-7.8
-7.2
-6.7
-6.1
-5.6
-5.0
-4.4
+77.0
+78.8
+80.6
+82.4
+84.2
+86.0
+87.8
+89.6
+91.4
+93.2
+95.0
+96.8
+98.6
+100.4
+102.2
+104.0
+106.8
+107.6
+109.4
+111.2
+113.0
+114.8
+116.6
+118.4
+120.2
+122.0
+123.8
+125.6
+127.4
+129.2
105 Visit mobil.ca /pds for the most current product information
From °C or °F
+25
+26
+27
+28
+29
+30
+31
+32
+33
+34
+35
+36
+37
+38
+39
+40
+41
+42
+43
+44
+45
+46
+47
+48
+49
+50
+51
+52
+53
+54
To °C
-3.9
-3.3
-2.8
-2.2
-1.7
-1.1
-0.6
0.0
+0.6
+1.1
+1.7
+2.2
+2.8
+3.3
+3.9
+4.4
+5.0
+5.6
+6.1
+6.7
+7.2
+7.8
+8.3
+8.9
+9.4
+10.1
+10.6
+11.1
+11.7
+12.2
Click Here to return to PRODUCT APPLICATION INDEX
APPENDICES
Temperature Conversion Table
+131.0
+132.8
+134.6
+136.4
+138.2
+140.0
+141.8
+143.6
+145.4
+147.2
+149.0
+150.8
+152.6
+154.4
+156.2
+158.0
+159.8
+161.6
+163.4
+165.2
+167.0
+168.8
+170.6
+172.4
+174.2
+176.0
+177.8
+179.6
+181.4
+183.2
+185.0
+186.8
+188.6
+190.4
+192.2
+194.0
+195.8
+197.6
+199.4
+201.2
+203.0
+204.8
+206.6
+208.4
+210.2
+212.0
+213.8
+215.6
+217.4
+219.2
+55
+56
+57
+58
+59
+60
+61
+62
+63
+64
+65
+66
+67
+68
+69
+70
+71
+72
+73
+74
+75
+76
+77
+78
+79
+80
+81
+82
+83
+84
+85
+86
+87
+88
+89
+90
+91
+92
+93
+94
+95
+96
+97
+98
+99
+100
+101
+102
+103
+104
To °C
+12.8
+13.3
+13.9
+14.4
+15.0
+15.6
+16.1
+16.7
+17.2
+17.8
+18.3
+18.9
+19.4
+20.0
+20.6
+21.1
+21.7
+22.2
+22.8
+23.3
+23.9
+24.4
+25.0
+25.6
+26.1
+26.7
+27.2
+27.8
+28.3
+28.9
+29.4
+30.0
+30.6
+31.1
+31.7
+32.2
+32.8
+33.3
+33.9
+34.4
+35.0
+35.6
+36.1
+36.7
+37.2
+37.8
+38.3
+38.9
+39.4
+40.0
To °F
From °C or °F
+221.0
+222.8
+224.6
+226.4
+228.2
+230.0
+231.8
+233.6
+235.4
+237.2
+239.0
+240.8
+242.6
+244.4
+246.2
+248.0
+251.6
+255.2
+258.8
+262.4
+266.0
+269.6
+273.2
+276.8
+280.4
+284.0
+287.6
+291.2
+294.8
+298.4
+302.0
+305.6
+309.2
+312.8
+316.4
+320.0
+323.6
+327.2
+330.8
+334.4
+338.0
+341.6
+345.2
+348.8
+352.4
+356.0
+359.6
+363.2
+366.8
+370.4
Visit mobil.ca /pds for the most current product information
+105
+106
+107
+108
+109
+110
+111
+112
+113
+114
+115
+116
+117
+118
+119
+120
+122
+124
+126
+128
+130
+132
+134
+136
+138
+140
+142
+144
+146
+148
+150
+152
+154
+156
+158
+160
+162
+164
+166
+168
+170
+172
+174
+176
+178
+180
+182
+184
+186
+188
To °C
+40.6
+41.1
+41.7
+42.2
+42.8
+43.3
+43.9
+44.4
+45.0
+45.6
+46.1
+46.7
+47.2
+47.8
+48.3
+48.9
+50.0
+51.1
+52.2
+53.3
+54.4
+55.6
+56.7
+57.8
+58.9
+60.0
+61.1
+62.2
+63.3
+64.4
+65.6
+66.7
+67.8
+68.9
+70.0
+71.1
+72.2
+73.3
+74.4
+75.6
+76.7
+77.8
+78.9
+80.0
+81.1
+82.2
+83.3
+84.4
+85.6
+86.7
To °F
+374.0
+377.6
+381.2
+384.8
+388.4
+392.0
+395.6
+399.2
+402.8
+406.4
+410.0
+413.6
+417.2
+420.8
+424.4
+428.0
+437.0
+446.0
+455.0
+464.0
+473.0
+482.0
+491.0
+500.0
+509.0
+518.0
+527.0
+536.0
+545.0
+554.0
+563.0
+572.0
+590.0
+608.0
+626.0
+644.0
+662.0
+680.0
+698.0
+716.0
+734.0
+752.0
+932.0
+1112.0
+1292.0
+1472.0
+1652.0
+1832.0
+2012.0
+2192.0
From °C or °F
To °C
+190
+192
+194
+196
+198
+200
+202
+204
+206
+208
+210
+212
+214
+216
+218
+220
+225
+230
+235
+240
+245
+250
+255
+260
+265
+270
+275
+280
+285
+290
+295
+300
+310
+320
+330
+340
+350
+360
+370
+380
+390
+400
+500
+600
+700
+800
+900
+1000
+1100
+1200
+87.8
+88.9
+90.0
+91.1
+92.2
+93.3
+94.4
+95.6
+96.7
+97.8
+98.9
+100.0
+101.1
+102.2
+103.3
+104.4
+107.2
+110.0
+112.8
+115.6
+118.3
+121.1
+123.9
+126.7
+129.4
+132.2
+135.0
+137.8
+140.6
+143.3
+146.1
+148.9
+154.4
+160.0
+165.6
+171.1
+176.7
+182.2
+187.8
+193.3
+198.9
+204.4
+260.0
+315.6
+371.1
+427.0
+482.0
+538.0
+593.0
+649.0
Click Here to return to PRODUCT APPLICATION INDEX
106
ALPHABETICAL INDEX OF PRODUCTS
From °C or °F
APPENDICIES
To °F
(continued)
APPENDICES
Viscosity Conversion Table
Kinematic Redwood KinematicRedwood KinematicRedwood
cSt 40 C
SUS
Engler No. 1 Sec.
cSt 40 C
SUS
Engler No. 1 Sec.
cSt 40 C
SUS
Engler No. 1 Sec.
2 32.61.14 30.8
3 36.01.22 33.2
4 39.11.31 35.8
5
42.5
1.40
38.4
6
45.7
1.48
41.0
7 49.01.56 43.7
8 52.01.65 46.5
9 55.71.74 49.2
1059.01.83 52.1
1162.51.92 55.2
1266.22.02 58.4
1370.02.12 61.6
1577.52.32 68.2
1785.52.55 75.2
19 942.77 82.8
21 1003.00 90.4
231113.23 98
251203.46 106
281333.83 117
301424.09 125
331554.46 137
351644.71 145
381785.10 157
401875.35 166
43
200 5.75
178
46 2146.15190
50 2336.65207
55 2567.25228
60
279
7.9
248
65
302
8.6
268
70 3259.25286
75 3499.85307
80 37210.5329
85 39511.2349
90 41811.8370
95 44212.5390
100 46513.2410
110 51114.5450
120 55815.8490
130 60517.1530
140 64918.4570
150 69519.7620
160 74221.0660
170 78822.5700
180 83424.0740
190 88125.0780
200 92726.0820
210 97328.0860
220102029.0900
230
1066 30.0
940
240111232 990
250115933 1030
260120534 1070
270
1251
36
1110
280
1297
37
1150
290134438 1190
300139040 1230
315146041 1300
330152943 1350
350162246 1440
370171549 1520
390180751 1600
410190054 1690
430199057 1770
450209059 1850
470218062 1930
490227064 2010
500232066 2050
550254072 2260
600278079 2460
650301086 2670
700324092 2880
750347099 3080
80037001053280
Dynamic Viscosity to Kinematic Viscosity Calculation
To convert from dynamic viscosity units, centipoise (cP), to kinematic viscosity units,
centi­stokes (cSt), use the following equation:
cSt = cP
Density (kg/L)
Note: Viscosity and density must be measured at the same temperature.
If viscosity is known at two or more different temperatures, viscosity at other temperatures
can be estimated using standard charts or equations. Charts are available from your
Imperial sales representative or technical services department.
107 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
50,000
Click Here to return to PRODUCT APPLICATION INDEX
TEMPERATURE, DEGREES CELSIUS /TEMPÉRATURE, DEGRÉS CELSIUS
3.0
150
3.0
140
4.0
4.0
130
5.0
5.0
120
6.0
6.0
110
7.0
7.0
100
8.0
8.0
90
10
9.0
10
9.0
80
15
15
70
20
20
60
30
30
50
40
40
40
50
50
30
75
75
20
100
100
10
150
150
0
200
200
-10
300
300
-20
500
400
500
400
-40
1,000
3,000
5,000
2,000
-30
VISCOSITY – TEMPERATURE CHART
RELATION VISCOSITÉ – TEMPÉRATURE
1,000
ALPHABETICAL INDEX OF PRODUCTS
Visit mobil.ca /pds for the most current product information
APPENDICIES
2,000
3,000
5,000
10,000
-10
20,000
-20
10,000
-30
20,000
-40
50,000
APPENDICES
108
KINEMATIC VISCOSITY, CENTISTOKES /VISCOSITÉ CINÉMATIQUE, CENTISTOKES
APPENDICES
SAE Viscosity Grades for Engine Oils
SAE
Viscosity
Grade
Low-temperature
Cranking
Viscosity1
cP at °C, Max.
0W
5W
10W
15W
20W
25W
20
30
40
40
50
60
6,200 @ -35
6,600 @ -30
7,000 @ -25
7,000 @ -20
9,500 @ -15
13,000 @ -10
—
—
—
—
—
—
Low-temperature
Low Shear Rate
Low Shear Rate
Pumping Viscosity
Kinematic
Kinematic
High Shear Rate
2
3
with no yield-stress Viscosity Viscosity3Viscosity4
cP at °C, Max.
cSt at 100°C, Min.
cSt at 100°C, Max.
cP at 150°C, Min.
60,000 @ -40
60,000 @ -35
60,000 @ -30
60,000 @ -25
60,000 @ -20
60,000 @ -15
—
—
—
—
—
—
3.8
3.8
4.1
5.6
5.6
9.3
5.6
9.3
12.5
12.5
16.3
21.9
—
—
—
—
—
—
<9.3
<12.5
<16.3
<16.3
<21.9
<26.1
—
—
—
—
—
—
2.6
2.9
2.95
3.76
3.7
3.7
Note: 1cP = 1mPa*s; 1cSt = 1mm2/s. All values are critical specifications as defined by ASTM D 3244.
1
ASTM D 5393 2 ASTM D 4684; note that the presence of any yield-stress detectable by this method constitutes a failure regardless of viscosity
3
ASTM D 445 4 ASTM D 4683, CEC L-36-A-90 (ASTM D 4741) or ASTM D 5481 5 0W-40, 5W-40 and 10W-40 6 15W-40, 20W-40, 25W-40 and 40
SAE J306 Viscosity Grades for Gear Oils
SAE iscosity Grade
V
70W
75W
80W
85W
80
85
90
140
250
1
Maximum Temperature for Brookfield Viscosity of 150,000 cP °C
Kinematic Viscosity at 100°C Min.1Max.
-55
-40
-26
-12
—
—
—
—
—
4.1 —
4.1 —
7.0 —
11.0 —
7.0
<11.0
11.0
<13.5
13.5
<24.0
24.0
<41.0
41.0 —
Limits must also be met after testing in CEC L-45-T-93 Method C (20 hours)
Classification of Greases by National Lubricating Grease Institute
(NLGI) Consistency Numbers1
NLGI
Grade No.
60-stroke Worked Penetration at 25°C
Min.
Max.
000
445475
00
400430
0
355385
1
310
340
2
265
295
NLGI
Grade No.
60-stroke Worked Penetration at 25°C
Min.
Max.
3
220250
4
175205
5
130160
6
85
115
The grades are defined as ranges of the values of the 60-stroke worked penetration, in tenths of millimetres, as determined by
ASTM D 217, ‘Cone Penetration of Lubricating Grease.’
1
109 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
APPENDICES
Understanding Oil Analysis
APPENDICIES
VISCOSITY
Probably the most important single property of a lubricating oil. It is a major factor in
the development of the load-carrying ability of an oil. It is defined as resistance to flow
at 40 degrees Centigrade and typically reported in Centistokes (cSt).
WEAR METALS
The presence of these metals can indicate a wear problem on a microscopic level before
the problem can be detected by conventional means. The existence of a wear problem
is determined not only by absolute values of metals, but more importantly by a relative
increase or trend in one or more of these metals.
MetalSources
MetalSources
Iron
Cylinders, Gears, Rings, Crankshafts,
Liners, Bearings, Rust
Tin
Bearing Plating, Compressors
Chromium
Rings, Bearing and Liner Plating
Aluminum
Pistons, Bearing and Pump, Blower and
Compressor Impellers
Lead
Bearing Overlays
NickelValves
Copper
Hydraulic Pumps, Bearing Cages,
Bushings, Bronze Components
Silver
Bearing and Bushing Plating
Manganese
Trace Element in Gas Turbine Components
CONTAMINANTS
These elements can be an indicator of contamination. The combination of contaminant
and wear metals can indicate a harmful machine operating condition.
ContaminantSources
Silicone
Boron
Sodium
Potassium
Acid
Oxidation
Water
Anti-freeze, Process Water, Condensation
GlycolAnti-freeze
Fuel
Fuel System
Soot
Incomplete Combustion, Blow-by
Chlorine
Land Fill Gas, Sea Water
Abrasive Dirt, Sealant, Defoamant
Anti-freeze, Oil Additive
Anti-freeze, Oil Additive
Anti-freeze, Oil Additive
Oil Degradation (TAN)
Thermal Degradation of Oil
ALPHABETICAL INDEX OF PRODUCTS
ContaminantSources
ADDITIVES
A chemical substance added to oil to impart or improve certain properties.
AdditiveFunctions
AdditiveFunctions
Magnesium
Dispersant/Detergent (TBN)
Calcium
Dispersant/Detergent (TBN)
BariumDispersant/Detergent
PhosphorusAnti-wear
ZincAnti-wear
MolybdenumAnti-wear
For further information contact your Imperial sales representative or go to signumoilanalysis.com.
Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
110
APPENDICES
ANSI-AGMA Industrial Gear Lubricants 9005-D94
R&O Inhibited Gear Oil AGMA Lubricant No. Viscosity Range cSt
at 40°C
Extreme Pressure Gear Oil
AGMA Lubricant No.
Synthetic Gear Oil
AGMA Lubricant No.
0
1
2
3
4
5
6
7, 7 Comp*
8, 8 Comp*
8A Comp*
9
10
11
12
13
14R**
15R**
28.8 to 35.2
41.4 to 50.6
61.2 to 74.8
90 to 110
135 to 165
198 to 242
288 to 352
414 to 506
612 to 748
900 to 1100
1350 to 1650
2880 to 3520
4140 to 5060
6120 to 7480
190-220 at 100°C***
428.5 to 857.0 at 100°C***
857.0 to 1714.0 at 100°C***
None
None
2 EP
3 EP
4 EP
5 EP
6 EP
7 EP
8 EP
8A EP
9 EP
10 EP
11 EP
12 EP
13 EP
None
None
0S
1S
2S
3S
4S
5S
6S
7S
8S
None
9S
10 S
11 S
12 S
13 S
None
None
AGMA Lubricant No.
ISO Viscosity Grade
Mobil Product
Mobil Synthetic Product
0
1
2
3
4
5
6
7
32
46
68
100
150
220
320
460
Mobil DTE Oil Light
Mobil DTE Oil Medium
Mobil DTE Oil Heavy Medium
Mobil DTE Oil Heavy
Mobil DTE Oil Extra Heavy
Mobil DTE Oil BB
Mobil DTE Oil AA
Mobil DTE Oil HH
Mobil SHC 624
Mobil SHC 625
Mobil SHC 626
Mobil SHC 627
Mobil SHC 629
Mobil SHC 630
Mobil SHC 632
Mobil SHC 634
AGMA Compounded
ISO Viscosity Grade
Mobil Product
7 Comp*
8 Comp*
8A Comp*
460
680
1000
Mobil 600W Super Cylinder Oil
Mobil Extra Hecla Super Cylinder Oil
Mobil Extra Hecla Super Cylinder Oil Mineral
AGMA Lubricant No.
ISO Viscosity Grade
2 EP
68
3 EP
100
4 EP
150
5 EP
220
6 EP
320
7 EP
460
8 EP
680
8A EP
1000
9 EP
1500
10 EP
11 EP
12 EP
13 EP
14R**
15R**
Mobil Product
Mobil Synthetic Product
Mobilgear 600 XP 68
Mobilgear 600 XP 100
Mobilgear 600 XP 150
Mobilgear 600 XP 220
Mobilgear 600 XP 320
Mobilgear 600 XP 460
Mobilgear 600 XP 680
None
None
Mobiltac LL
None
Mobiltac MM
Mobiltac QQ
None
Mobiltac 325 NC, 375 NC
None
None
Mobil SHC Gear 150
Mobil SHC Gear 220
Mobil SHC Gear 320
Mobil SHC Gear 460
Mobil SHC Gear 680
Mobil SHC Gear 1000
Mobil SHC Gear 1500
Mobil SHC Gear 3200
None
Mobil SHC Gear 6800
None
None
None
* Oils marked “Comp” are compounded with 3% to 10% fatty or synthetic fatty oils.
**Residual compounds-diluent type, commonly known as solvent cutbacks, are heavy oils containing a volatile, non-flammable diluent for ease of application.
The diluent evaporates leaving a thick film of lubricant on the gear teeth. Viscosities listed are for the base compound without diluent.
***Viscosities of AGMA Lubricant Number 13 and above are specified at 100°C (210°F) as measurement of viscosities of these heavy lubricants at 40°C
(100°F) would not be practical.
111 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
ALPHABETICAL LIST OF PRODUCTS
Mobil 1™.....................................................................................................................74
Mobil 1™ Advanced Fuel Economy............................................................................. 74
Mobil 1™ ESP Formula M 5W-40................................................................................75
Mobil 1™ ESP X1 0W-30............................................................................................75
APPENDICIES
Mobil 1™ Extended Performance 5W-20, 5W-30 and 10W-30....................................75
Mobil 1™ Racing 4T....................................................................................................78
Mobil 1™ Synthetic ATF..............................................................................................77
Mobil 1™ Synthetic Gear Lube LS..............................................................................78
Mobil 1™ Synthetic Grease.........................................................................................91
Mobil 1™ Turbo Diesel Truck 5W-40............................................................................ 76
Mobil Aero™ HFA........................................................................................................86
Arapen™ RB 320...................................................................................................... 102
Mobil™ Arcan 1...........................................................................................................99
Mobil™ Argon EP........................................................................................................99
Mobil Arox™ EP Series...............................................................................................48
Mobil Arox™ NM 000................................................................................................. 101
Mobil™ Aviation Grease SHC 100...............................................................................85
Mobil Beacon™ 325.................................................................................................. 103
Canthus™ 680.............................................................................................................45
Mobil Centaur™ Moly Series..................................................................................... 100
Mobil Centaur XHP™ 221......................................................................................... 101
Mobil Centaur XHP™ 460 Series................................................................................98
Mobil™ Chainoil.......................................................................................................... 18
Mobil™ Compressor Oils.............................................................................................24
Mobil™ Compressor Oils 264 and 460........................................................................24
ALPHABETICAL INDEX OF PRODUCTS
Mobil™ Compressor Oil N 100....................................................................................24
Mobil™ Cylinder Oils ..................................................................................................25
DDR Grease.............................................................................................................. 102
Mobil Delvac 1™ ESP 5W-40 and 0W-40...................................................................60
Mobil Delvac 1™ LE 5W-30.........................................................................................60
Mobil Delvac™ 1300 Super 10W-30 and F2 15W-40..................................................61
Mobil Delvac™ 1230 and 1240....................................................................................61
Mobil Delvac™ 1640....................................................................................................61
Mobil Delvac™ CNG/LNG 15W-40..............................................................................62
Mobil Delvac™ Elite 10W-30 and 15W-40...................................................................60
Mobil Delvac™ Elite 222 0W-30..................................................................................60
Mobil Delvac™ Extended Life Coolant/Antifreeze – C Series.....................................69
Mobil Delvac™ Synthetic ATF......................................................................................63
Mobil Delvac™ Synthetic Final Drive and Axle Oil.......................................................63
Mobil Delvac™ Synthetic Gear Oils.............................................................................63
Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
112
ALPHABETICAL LIST OF PRODUCTS
Mobil Delvac™ Synthetic Transmission Fluid 50.........................................................63
Mobil Delvac™ Xtreme Grease................................................................................. 100
Mobil™ Dexron®-VI ATF...............................................................................................77
DIOL™ 9 RD Series....................................................................................................62
Mobil DTE 10 Excel™ Series......................................................................................37
Mobil DTE™ 20 Series................................................................................................38
Mobil DTE™ 724 Oil....................................................................................................53
Mobil DTE™ 732 M.....................................................................................................53
Mobil DTE™ 700 Series..............................................................................................53
Mobil DTE™ 800 Series..............................................................................................52
Mobil DTE™ 932 GT...................................................................................................52
Mobil DTE™ FM Series...............................................................................................27
Mobil DTE™ Oil 205 ...................................................................................................25
Mobil DTE™ Oil Named Series...................................................................................20
Mobil DTE™ PM Series..............................................................................................47
Mobil Dynagear™ Series.............................................................................................95
Mobil Epic™ Series.....................................................................................................98
Exxcolub™ SCF PG....................................................................................................22
Exxcolub™ SCF PS....................................................................................................22
Exxcolub™ SCF M2....................................................................................................22
Exxon™ Aviation Oil Elite 20W-50...............................................................................86
Exxon HyJet™ IV-A Plus.............................................................................................85
Faxam™......................................................................................................................45
Mobil Fenso™ Series..................................................................................................48
Formesso™ Summer Grade.......................................................................................43
Forum™ EP 46 and 68................................................................................................40
Galcar All Year.............................................................................................................68
Galena™ Tramo 3735................................................................................................ 102
Mobil Gargoyle™ Arctic Oils........................................................................................49
Mobil Gargoyle Arctic SHC™ 200 Series................................................................... 49
Mobil Geargard™........................................................................................................95
Mobil Geargard™ HVS................................................................................................36
Mobil GEO™ 15W-40 .................................................................................................62
Mobil Glygoyle™ 22.....................................................................................................49
Mobil Glygoyle™ Series..............................................................................................35
Mobil Glygoyle™ Numbered Series............................................................................. 19
Mobil™ Heavy Duty (HD) Chainoil.............................................................................. 18
Mobil™ Heavy Duty SCA Precharged Coolant/Antifreeze...........................................69
Mobil Hydraul™...........................................................................................................68
Mobil Iogear™ EP 100.................................................................................................36
113 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
ALPHABETICAL LIST OF PRODUCTS
Mobil Jet Oil™ II..........................................................................................................86
Mobil Jet Oil™ 254......................................................................................................86
Mobil Marvelube™ EP 9F............................................................................................94
Millcot™ K................................................................................................................... 18
Mobil™ Multi-Vehicle ATF............................................................................................77
APPENDICIES
Mobil Nuto™ H Series.................................................................................................40
Mobil Nyvac™ FR 200D..............................................................................................41
Mobil Pegasus™ 1.......................................................................................................29
Mobil Pegasus™ 605...................................................................................................31
Mobil Pegasus™ 610...................................................................................................30
Mobil Pegasus™ 710...................................................................................................30
Mobil Pegasus™ 801 Series .......................................................................................31
Mobil Pegasus™ 805...................................................................................................29
Mobil Pegasus™ AGX.................................................................................................31
Mobil Pegasus™ GLX.................................................................................................30
Mobil Pegasus™ GMA................................................................................................29
Mobil Polyrex™ EM.....................................................................................................93
Mobil Pyrogard™ 53....................................................................................................41
Mobil Rarus™ 427 ......................................................................................................21
Mobil Rarus™ 800 Series...........................................................................................21
Mobil Rarus SHC™ 1020 Series.................................................................................21
Mobil Ronex™ MP.......................................................................................................91
Mobil™ Sawguide Oils................................................................................................45
Mobil SHC™ 500 Series.............................................................................................37
Mobil SHC™ 600 Series............................................................................................. 19
ALPHABETICAL INDEX OF PRODUCTS
Mobil SHC™ 800 Series.............................................................................................52
Mobil SHC Aware™ Grease EP 2...............................................................................83
Mobil SHC Aware™ H Series......................................................................................83
Mobil SHC Cibus™ Series..........................................................................................27
Mobil SHC™ Gear OH Series.....................................................................................35
Mobil SHC Gear™ 1500, 3200, and 6800...................................................................33
Mobil SHC Gear™ 46M...............................................................................................36
Mobil SHC Gear™ Series (ISO VG 150-1000)............................................................33
Mobil SHC™ Grease 100 EAL Series.........................................................................93
Mobil SHC™ Grease 460 WT.................................................................................... 104
Mobil SHC Pegasus™ 30............................................................................................29
Mobil SHC™ PF 462................................................................................................. 103
Mobil SHC™ PM Series..............................................................................................47
Mobil SHC Polyrex™ 462............................................................................................94
Mobil Super™ 1000..................................................................................................... 76
Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
114
ALPHABETICAL LIST OF PRODUCTS
Mobil Super™ 2000..................................................................................................... 76
Mobil Super™ 3000..................................................................................................... 76
Mobil ATF™ +4............................................................................................................77
Mobil ATF™ 3309........................................................................................................77
Mobil ATF™ D/M..........................................................................................................77
Mobil™ Synthetic Oven Lube 1090.............................................................................46
Mobil Synturion™ 6.....................................................................................................46
Mobil™ System Cleaner..............................................................................................46
Mobil Teresso™...........................................................................................................54
Mobil Teresso™ GTC Series.......................................................................................54
Mobil Teresstic™ AC 32...............................................................................................24
Mobil Teresstic™-C......................................................................................................20
Mobil Teresstic™ V 150...............................................................................................20
Mobil Unirex™ EP Series............................................................................................99
Mobil Unirex™ N..........................................................................................................93
Mobil Univis™ BIO-C 40..............................................................................................39
Mobil Univis™ Extra....................................................................................................38
Mobil Univis™ HVI 13..................................................................................................39
Mobil Univis™ N-C Series...........................................................................................39
Mobil Univis™ Ultra.....................................................................................................38
Mobil Vactra™ Oil Numbered Series...........................................................................55
Mobil Vacuoline™ 500 Series...................................................................................... 19
Mobil Vacuoline™ 1400 Series....................................................................................55
Mobil Vaprotec™ Light.................................................................................................50
Mobil Velocite™ Oil Numbered Series.........................................................................51
Mobil Zerice™ S Oils...................................................................................................49
Mobilarma™ 245.........................................................................................................50
Mobilarma™ 700 Series..............................................................................................50
Mobilcut™ 100.............................................................................................................42
Mobilcut™ 140.............................................................................................................43
Mobilcut™ 350.............................................................................................................43
Mobilgard™ 12 Series.................................................................................................82
Mobilgard™ 300..........................................................................................................81
Mobilgard™ 410 NC (No Chlorine)..............................................................................82
Mobilgard™ 525..........................................................................................................81
Mobilgard™ 560 VS.....................................................................................................81
Mobilgard™ 570..........................................................................................................81
Mobilgard™ ADL Series..............................................................................................82
Mobilgard™ M30, M40 and M50.................................................................................82
Mobilgear™ 600 XP Series.........................................................................................34
115 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
ALPHABETICAL LIST OF PRODUCTS
Mobilgear™ MS Series...............................................................................................44
Mobilgear SHC™ XMP Series....................................................................................35
Mobilgrease™ 28........................................................................................................85
Mobilgrease™ 33........................................................................................................85
Mobilgrease™ FM 101.................................................................................................94
APPENDICIES
Mobilgrease XHP™ 220 Series...................................................................................97
Mobilgrease XHP™ 460 Series...................................................................................97
Mobilgrease XHP™ Mine.......................................................................................... 100
Mobilgrease™ XTC.....................................................................................................92
Mobilith SHC™ PM.................................................................................................... 101
Mobilith SHC™ Series.................................................................................................97
Mobilmet™ 420 Series................................................................................................42
Mobilmet™ 760 Series................................................................................................42
Mobiltac™ 375 NC......................................................................................................36
Mobiltemp SHC™ 32...................................................................................................96
Mobiltemp™ Series.....................................................................................................96
Mobiltherm™ and Thermoil™......................................................................................37
Mobiltrans™ AST (All-Season Transmission)..............................................................67
Mobiltrans™ AST 30 and Mobiltrans™ AST Extra 20.................................................67
Mobiltrans™ HD 10W, 30 and 50................................................................................67
Mobilube™ HD Extra MG 75W and 80W-140.............................................................66
Mobilube™ HD LS 80W-90.........................................................................................66
Mobilube™ HD Plus MG 75W, 80W-90 and 85W-140................................................66
Mobilube™ XFD 50 and 60.........................................................................................66
Mobilux™ EP 111.........................................................................................................92
ALPHABETICAL INDEX OF PRODUCTS
Mobilux™ EP Series...................................................................................................98
Nebula™ EP Special...................................................................................................94
Slurry Oil 62.................................................................................................................46
SPARTAN™ EP-C.......................................................................................................34
Thredkote™ 706........................................................................................................ 103
Voltesso™...................................................................................................................51
Wire Rope Dressing................................................................................................... 104
Z-50 Pipe Dope......................................................................................................... 104
Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
116
Viscosity Classification Equivalents
ISO VISCOSITY CLASSIFICATION SYSTEM
Many petroleum products are graded according to the ISO Viscosity Classification System,
approved by the International Standards Organization (ISO). Each ISO viscosity grade number
corresponds to the mid-point of a viscosity range expressed in centistokes (cSt) at 40°C. For
example, a lubricant with an ISO grade of 32 has a viscosity within the range of 28.8–35.2, the
midpoint of which is 32.
Rule-of-Thumb: The comparable ISO grade of a given product whose viscosity in SUS at 100°F is
known can be determined by using the following conversion formula:
SUS @ 100°F ÷ 5 =cSt
˜
@ 40°C
117 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
TM
Brief Product Descriptions
Imperial Oil
Downstream and Chemical
237 Fourth Avenue SW, Calgary, Alberta T2P 3M9
2015 Edition – Canada
For more information: 1- 888-968-3776
Brief Product Descriptions
mobil.ca
mobildelvac.ca
mobilindustrial.com
All trademarks used herein are trademarks or
registered trademarks of Exxon Mobil Corporation
or one of its subsidiaries.
2015 Edition – Canada
TM
TM
TM
TM
TM
TM
TM
TM
TM
TM