Landford 4 Seater
Square Cube Table
Assembly Instructions
Product size:
L125*W125*H75 cm
Protective Furniture Cover is included.
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 1 / 6
Landford 4 Seater
Square Cube Table
Assembly Instructions
Before you start
Don’ts
Warnings
IMPORTANT, RETAIN FOR FUTURE
REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Do not place very hot or very cold items on the glass surface
unless adequately thick table-mats are used to prevent such
items from coming into contact with the glass.
Do not use the glass as a chopping surface. Do not strike glass
with hard or pointed items.
Do not strike the glass with hard or pointed items.
Do not use power tools to construct this product.
Ensure that this product is fully assembled as illustrated before
use.
This product should only be used on firm, level ground.
Do not use this product if parts are missing, damaged or worn.
Do not sit or lean on this product.
Do not stand or climb onto the product and do not use it as a ladder,
as this could lead to it unbalancing and overturning.
Keep small parts out of reach of children.
Do not stand or climb onto this product.
This product is intended for Domestic
Do not use scourers, abrasives, washing powders, chemical cleaners
or any other substances containing abrasives since these substances
can damage the product, including the glass panel.
Never drag furniture when moving it, always lift it.
Use only.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Number of people required for assembly
Two people
Dos
Time to assemble
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Removing all packaging and banding and place the components
carefully on suitable surfaces to prevent damaging or scratching
them.
Check the pack and make sure you have all parts listed.
Check all screws and bolts are tightened and inspect regularly.
30 Minutes
Tools required
We recommend the use of furniture covers to protect your product
when not in use.
This product is suitable for all year outdoor use.
However to prolong its life we recommend that during severely
bad weather and during the winter months, it is stored in a cool,
dry place.
Before storage, ensure that the product is clean and dry.
To clean, wipe down with a sponge and warm soapy water and
wipe with a clean, dry cloth.
Tips:
Do NOT fully tighten bolts before
all components are connected.
Only fully tighten once you are
satisfied with the alignment of all
components.
Do not overtighten bolts.
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 2 / 6
Landford 4 Seater
Square Cube Table
Assembly Instructions
Components, fixtures & fittings (not actual size)
Table Parts List
Part
No.
Diagram
A
Qty
Part
No.
1 PC
B
Diagram
Qty
1 PC
Table Top Frame
Upper Cross Leg
C
1 PC
D
1 PC
Glass Top
Bottom Cross Leg
E
1 PC
F
1 PC
Parasol Hole Cap
Connecting Panel
F2
12 PCS F62
M6*15mm Bolt
Bolt Head Cap
F3
12 PCS
Washer
12 PCS
S1
1 PC
Socket Wrench
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 3 / 6
Landford 4 Seater
Square Cube Table
Assembly Instructions
Step by step assembly instructions
Step One
Open the packaging, take out the contents and carefully leave the glass on the carton until the
rest of the table is fully assembled.
With the help of another person, place the Table Top Frame (A) upside down on a flat,
non-abrasive surface to avoid scratching the table surface or rim.
Do NOT assemble the Legs (B&C) to the Table Top Frame (A) while it is still resting on the
Glass Top (D).
Step Two
With the help of another person, stand two legs upside down.
Place the Bottom Cross Leg (C) onto the Upper Cross Leg (B), align the assembly holes,
using Connecting Panel (E), Bolts (F62) and Washers (F3) to connect them.
DO NOT fully tighten the bolts.
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 4 / 6
Landford 4 Seater
Square Cube Table
Assembly Instructions
Step Three
Place the Assembled Legs onto the Table Top Frame (A), align the assembly holes, using Bolts
(F62) and Washers (F3) to connect them.
At this stage, please don't fully tighten the bolts; just assemble all bolts into place so that they
still turn freely.
Step Four
With the help of another person, carefully lift the partly-assembled table in upright position.
Level the table with adjustable feet screws.
Once you are satisfied with the alignment of all components, carefully tighten all bolts
using Socket Wrench (S1), cover all Bolt Heads with Bolt Head Caps (F2).
During this step (Levelling step and Bolts-tightening step), you may have to turn around the
table upside down for several times.
Adjustable Foot Screw
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 5 / 6
Landford 4 Seater
Square Cube Table
Assembly Instructions
Step Five
With the help of another person, carefully lift the Glass Top (D) and place it onto
the Table Top Frame (A).
The glass top should be securely inlaid into the Table Top Frame (A).
Make sure the glass top is evenly rested on the Table Top Frame (A).
Insert the Parasol Hole Cap (F) into the middle hole in the Glass Top (D) and the
Table Top Frame (A).
Your table is now ready for use.
Tips to store the Cover: When the Protective Furniture Cover is not in use, please hold it in the Cover Bag and hang/attach it by velcro to the wicker plait which is under the Chair Seating.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 6 / 6
Landford Cube Chair
with Footstool
Assembly Instructions
Product size:
Chair: W58*D58*H68 cm
Footstool: W55*D49*H35.5 cm
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd. © A Mir & Co., Ltd. 1 / 4
Landford Cube Chair
with Footstool
Assembly Instructions
Before you start
Warnings
Don’ts
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Do not use scourers, abrasives, washing powders, chemical cleaners
or any other substances containing abrasives since these substances
can damage the product.
Never tilt the chair during use.
Failure to follow the warnings could result in serious injury.
Do not use this product if parts are missing, damaged or worn.
Handle heavy parts with care.
Do not stand or climb onto the product and do not use it as a ladder,
as this could lead to it unbalancing and overturning.
This product should only be used on firm, level ground.
Do not stand or climb onto this product.
This product is intended for
Never drag furniture when moving it, always lift it.
domestic use only.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Number of people required for assembly
One person
Dos
Time to assemble
When you are ready to start, make sure that you have plenty of
space and a clean, dry area for assembly.
Remove all packaging and banding and place the components
carefully on suitable surfaces to prevent damaging or scratching
them.
No assembly required
Tools required
No tools are required
Check the pack and make sure you have all parts listed.
We recommend the use of furniture covers to protect your product
when not in use.
This product is suitable for all year outdoor use. Cushions should
not be left out in wet weather or overnight.
To prolong the life of the product we recommend that during
severely bad weather and during the winter months, it is stored in
a cool, dry place.
Before storage, ensure that the product is clean and dry.
To clean, wipe down with a sponge and warm soapy water and
wipe with a clean, dry cloth.
Cushions should be cleaned following the care instruction on the
label.
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd. © A Mir & Co., Ltd. 2 / 4
Landford Cube Chair
with Footstool
Assembly Instructions
Parts List
Part
No.
Diagram
A
Qty.
Part
No.
2 PCS
B
2 PCS
Footstool
Qty.
4 PCS
Seat/Backrest
Cushion
Cube Chair
C
Diagram
D
2 PCS
Footstool Cushion
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd. © A Mir & Co., Ltd. 3 / 4
Landford Cube Chair
with Footstool
Assembly Instructions
This product does not require assembly.
We recommend that the cushions are stored indoors or under cover in wet
weather.
For storage, please remove the Footstool Cushion, Backrest cushion & Seat
cushion, fold down the backrest, then place Cushions onto the folded
backrest. Place the Footstool under the Cube Chair. There are storage bars
under the cube chair.
Warning: This chair is not a toy. Don’t let children play with foldable
backrest.
Never tilt the Chair or Footstool during use.
Ensure the product is always placed firmly
on the ground.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd. © A Mir & Co., Ltd. 4 / 4
Landford 3m Parasol
Assembly Instructions
Product Reference Size:
Dia290/300*H245 cm
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd. © A Mir & Co., Ltd.
1/4
Landford 3m Parasol
Assembly Instructions
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before
use.
This product should only be used on firm, level ground.
The product contains small parts which could
pose a risk to young children. Keep small parts
out of reach of children.
This product is intended for domestic use only.
Ensure the product is always placed on level ground.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Keep hands away from folding mechanism and
moving parts to prevent possible injury.
NEVER USE OR OPEN THIS PARASOL
WITHOUT A SUITABLE BASE SET IN PLACE.
Dos
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Unwrap all packaging materials and place the components on
suitable surface to prevent scratching your product.
Check the pack and make sure you have all of the parts listed.
from forming. Most stains can be removed with a mild detergent.
The parasol is not 100% waterproof and water may seep through
the seams and/or fabric in heavy rain. Ensure that the parasol is
fully dry before use.
Don’ts
Do not stand or climb onto the product.
Do not use power tools to construct this product.
Do not sit or lean onto the rims of this product.
Do not use this product if parts are missing, damaged or worn.
Do not leave the parasol open when there is a risk of high winds, as
damage will occur to its structure.
Never use scourers, abrasives or chemical cleaner.
Never use a pressure hose or washer to clean the product.
Never drag furniture when moving it, always lift it.
Never move this parasol when fully assembled.
To avoid damage do not allow water to collect or “pool” on the fabric.
The parasol is not 100% waterproof and water may seep through
the seams and/or fabric in heavy rain. Ensure that the parasol is
fully dry before use.
It is recommended that before moving heavy objects to a new
location they be completely disassembled to avoid personal injury
or damage to the furniture. Please be careful to retain all fittings
when doing this.
Please ensure you have correctly installed the parasol before use.
A competent person should carry out assembly. No liability will be
accepted for damage or injury caused by incorrectly installed or
assembled furniture.
Number of people required for assembly
One person.
Time to assemble
5 Minutes
Check all screws and bolts are tightened and inspect regularly.
We recommend the use of furniture covers to protect your product
when not in use.
During bad weather or in winter months, the product should be
stored in a cool, dry place. Before storage, ensure that the product
is clean and dry.
Tools required
None
To clean, wipe with a damp sponge and a little warm soapy water
then dry with a clean, dry cloth. Do not use solvent-based cleaners
or detergents as they can bleach or damage the product.
Clean the fabric using a little warm soapy water. The product must
be thoroughly dried afterwards to prevent mildew and mould stains
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd. © A Mir & Co., Ltd.
2/4
Landford 3m Parasol
Assembly Instructions
Parts List
Part
No.
Diagram
A
Qty
1 PC
Part
No.
B
Diagram
Qty
Bottom Pole
1 PC
Main Parasol Part
Assembly and Usage Steps
1. Press the Spring Pin and insert the Bottom Pole (B) into the Main Parasol Part (A);
2. Place the parasol at the intended place for use;
3. Rotate clockwise the Crank to spread the parasol canopy;
4. The parasol is closed by reversing above steps.
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd. © A Mir & Co., Ltd.
3/4
Landford 3m Parasol
Assembly Instructions
WARNING
Please take care to
keep fingers away
from moving parts
and crank rotating
area to prevent
possible injury.
To tilt the canopy
When the Parasol is in its upright position, continually rotate clockwise the crank handle
until the top canopy part is tilted.
The parasol canopy is erected by reversing above steps.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
www.a-mir.co.uk Produced in China for A Mir & Co., Ltd. © A Mir & Co., Ltd.
4/4