NATIONAL
wE1a-m
STANDARDS
h MEASURES (PATTERNS
0F IN~TRUME~~TS)
REGULATION
SUPPLEMENTARY CERTIFICATE
This
is to certify
that
an
pattern
and variant of the
approval
has
COMMISSION
REGULATIONS
9
OF APPROVAL No S135
been
granted
by
the
Commission
that
the
HBM Model Z6H2 Load Cell Of 500 kg Capacity
submitted by Electrical Equipment
192 Princes
Arncliffe,
are suitable
instrument.
for
use
The approval of the
Hwy
NSW,
for
Ltd
2205,
when
trade,
used
in
a
pattern and variant is subject
Commission-approved
to
review on or after
weighing
l/4/88.
Any
instrument incorporating a load cell purporting
to comply with this approval
shall be marked NSC No S135 in addition
to the approval number of the instrument.
Relevant
drawings
and specifications are lodged with
the
Comnission.
Conditions of Approval
1.
The number of scale intervals applicable to the weighing
instrument shall
be no greater than the number of verification
scale intervals approved for
the
basework, or the
load cell, or the
headwork,
whichever
is
the
smallest..
2.
The load cells to be used shall be subject
National Standards Commission.
to
regulor certification by the
Descriptive Advice
Pattern:
.
approved
18/2/Q
HBM model Z6H2 load cell of
500
kg copocity.
approved 18/2/83
1.
In
various capacities as per Table 1.
Technic01 Schedule No S135 dated
16/3/83 describes the
pattern
and
variant.
Filing Advice
The documentation for this approval comprises:
Certificate of Approval No ST35 dated 16/3/83
Technical
Schedule No S135 dated 16/3/83 (including Table 1)
Figures 1 and 2 dated 1613183.
16/3/03
NATIONAL
W,?&
STANDARDS
TECHNICAL
COMMISSION
SCHEDULE No S135
Pattern:
HBM Model Z6H2 Load Cell Of SO0 kg Capacity
Submittor:
Electrical Equipment
192
Ltd
Highway
Arncliffe, NSW, 2205.
Description of
1.
The Pattern
1) assembled
Mounting
in Figure
Pattern
is an HBM model
Z6H2 load cell
of
a Commission-approved
basework.
in
Method
1.1
-
Princess
of
is to
2.
500
kg capacity
(Figure
1 and
Table
mounting
be in
accordance
with the
manufacturer’s
instructions and as shown
Marking
1.2
The following is the
Manufacturer’s
minimum
dato
name or
required to be marked on the
2.
Description of
2.1
Variant 1
cell:
mark
Model number
Serial
number
Output
in the
Maximum rated
load
z6H2
.. . . . .
. . .mV/V
. . . ..kg
form
capacity in the
form
Variant
HBM model Z6H2 load cells of
vorious capacities as specified
in Table
1.
TABLE 1
Type:
HBM Z6H2
200
500 kg
100
verification stole
intervals
3000
3000
3000
3000
Minimum dead
3 kg
8 kg
17 kg
130
Maximum number
Minimum
value
of
load
0.005
Cable
3m
(tO.lm)
kg
0.01
0.02
kg
3m
3m
HBM Model
Z6H2
Approved
16/3/03
kg
of
verification
scale intervol
length
kg
kg
50 kg
Moximum capacity
Load
Cell -
Capacities
kg
0.05
3m
kg
19 June 1995
National
Standards
NOTIFICATION
VARIOUS
The following change
as listed below.
Commission
OF CHANGE
CERTIFICATES
OF APPROVAL
is made to the approval documentation
for various approvals
In the Certificates
and Technical Schedules of the approvals
references to the Submittor are changed to read:
Hottinger Baldwin Messtechnik
Im Tiefen See 45
D-64293
Darmstadt
Germany
APPROVAL
NUMBER
(#)
Some approvals
below,
GmbH
PATTERN
HBM
HBM
HBM
HBM
HBM
HBM
PS1 34
% s135
S136
s137
S282
s310
listed
Model
Model
Model
Model
Model
Model
Z6H3
Z6H2
C3H2
Z3H2
C3H2
C3H2
have other capacities
Signed and sealed by a person authorised under
Measurement
National
Regulation 9
of
the
(Patterns of Measuring
Instruments)
Regulations
to exercise
the powers
and functions
of the
Commission under this Regulation.
(#)
Load
Load
Load
Load
Load
Load
Cell
Cell
Cell
Cell
Cell
Cell
as variants.
of 200 kg Capacity
of 500 kg Capacity
of 50 t Capacity
of 1000 kg Capacity
of 100 000 kg Capacity
of 30 000 kg Capacity
all
FIGURE S135 - 2
force appilcatlon
i
Alternative Mounting Methods
16/3/83