MILESTONE
H E L P I N G
P A T I E N T S
MacroVIEW DM (Digital Mobile)
Macro Imaging System for anatomy/forensic studies
Operator Manual
MM079
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
Thank you for having selected our system and welcome to the ever growing world club of users for Milestone
laboratory instrumentation.
We are sure that you will be completely satisfied with this new tool entering your laboratory.
We invite you to read carefully this operator manual and to keep it in reach for convenient and fast
consulting.
For any possible clarification or any request for assistance please contact either our Representative in your
country:
Or contact
Milestone s.r.l.
Via Fatebenefratelli, 1/5
24010 Sorisole (BG) Italy
Tel. +39.035.412 8264
Fax +39.035.575498
web site www.milestonemedsrl.com
e-mail [email protected]
Please read the user manual before using the device.
MM079-006 – MacroVIEW DM – Operator Manual
2015-06
3
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
SUMMARY
SUMMARY ........................................................................................................................................................ 4
1. INTRODUCTION ........................................................................................................................................ 5
1.1.
INTRODUCTION TO MacroVIEW DM .............................................................................................. 5
1.2.
SYMBOL USED ................................................................................................................................. 5
1.3.
TECHNICAL SPECIFICATIONS ....................................................................................................... 6
1.4.
TRANSPORTATION AND STORAGE CONDITIONS ...................................................................... 7
1.5.
WARNING.......................................................................................................................................... 7
1.6.
REMOVAL OF EQUIPMENT FOR REPAIR ...................................................................................... 7
1.7.
ANTIVIRUS ........................................................................................................................................ 8
1.8.
BACKUP MacroVIEW DM DATA (IMAGES OF THE CASES) ......................................................... 8
1.9.
MILESTONE REMOTE CONNECTION ............................................................................................ 8
1.10. MARKING PLATES FOR MacroVIEW DM........................................................................................ 8
2. MACROVIEW DM INSTALLATION............................................................................................................ 9
2.1.
UNPACKING CHECK LIST ............................................................................................................... 9
2.2.
MacroVIEW DM INSTALLATION .................................................................................................... 12
2.2.1.
Macroview DM dimensions ...................................................................................................... 12
2.2.2.
Installing the fuse and the battery ............................................................................................ 13
2.2.3.
Camera lens setup ................................................................................................................... 14
2.2.4.
Control module PC panel setup ............................................................................................... 15
2.2.5.
PC panel connections .............................................................................................................. 15
2.2.6.
Installation and connection of the wired full total body camera (optional) ............................... 16
3. OPERATING MacroVIEW DM ................................................................................................................. 20
3.1.
START THE MacroVIEW DM .......................................................................................................... 20
3.2.
OVERVIEW OF SCREEN FUNCTIONS ......................................................................................... 21
3.3.
OPERATING MacroVIEW DM ......................................................................................................... 23
3.4.
ANNOTATION MODE ..................................................................................................................... 25
3.5.
IMAGE MEASURE CALIBRATION ................................................................................................. 30
3.6.
CHECK THE CART BATTERY STATUS ........................................................................................ 32
3.7.
SOFTWARE SETTINGS ................................................................................................................. 33
3.7.1.
Main Cam ................................................................................................................................. 34
3.7.2.
Second Cam ............................................................................................................................ 35
3.7.3.
Customization .......................................................................................................................... 36
3.7.4.
Save as default for new users ................................................................................................. 37
3.8.
CAM SETTINGS .............................................................................................................................. 38
4. MacroVIEW DM AS VIEWER MULTISTATIONS ..................................................................................... 40
4.1.
HOW TO INSTALL THE MacroVIEW DM AS VIEWER .................................................................. 40
4.2.
HOW TO MAKE AVAIBLE MacroVIEW DM IMAGES IN A LOCAL AREA NETWORK ................. 40
4.2.1.
Settings MacroVIEW DM PC ................................................................................................... 41
4.2.2.
Settings MacroVIEW DM Viewer PC ....................................................................................... 42
5. ACCESSORIES (OPTIONAL) .................................................................................................................. 43
5.1.
USB BARCODE READER (INCLUDES HOLDER) (CODE 370059) .............................................. 43
5.2.
WIRED FULL TOTAL BODY FOR MacroVIEW DM (CODE 372401)............................................. 43
6. MANTENAINCE OF THE MacroVIEW DM .............................................................................................. 44
6.1.
CLEANING OF THE MacroVIEW DM ............................................................................................. 44
6.2.
SUBSTITUTION OF THE BATTERY .............................................................................................. 44
7. TROUBLESHOOTING THE MacroVIEW DM .......................................................................................... 45
7.1.
MANIPULATOR KEYPAD DOES NOT WORK ............................................................................... 45
7.2.
TOUCH SCREEN RECALIBRATION .............................................................................................. 48
7.3.
DIRECT PRINTING CONFLICT ...................................................................................................... 50
7.4.
COPY TO USB CONFLICT ............................................................................................................. 50
8. WASTE DISPOSAL .................................................................................................................................. 51
8.1.
WASTE DISPOSAL OF MacroVIEW DM UNIT............................................................................... 51
8.2.
WASTE DISPOSAL OF BATTERY ................................................................................................. 51
4
Milestone s.r.l.
1.
MM079-006 – MacroVIEW DM – Operator Manual
INTRODUCTION
1.1. INTRODUCTION TO MacroVIEW DM
The purpose of the MacroVIEW DM and its accessories is to capture and storage digital images, audio
comments and short video of whole body, body parts and larger organ systems examined at autopsy,
grossing room and forensic pathology.
The system has been conceived for laboratory use and can therefore withstand the harshest laboratory
conditions.
Before operating, it is strictly necessary to attend a training course with a Milestone SERVICE specialist.
1.2. SYMBOL USED
An instruction accompanied by this symbol provides a quite important and require
more attention.
An instruction accompanied by this symbol provides a cautionary statement: failure to
follow the instruction may endanger the operator or cause damage to the instrument.
An instruction accompanied by this symbol provides a caution against electric shock.
Be sure to follow the instruction to prevent accidents resulting from electric shock.
Biohazard: be careful when you execute the procedure marked with this symbol:
danger of biohazard contamination.
CE logo: this instrument complies to European Community directives.
IVD medical device according to 98/79/EC directive.
WEEE European directive symbol (2002/96/EC):
Electric/electronic device do not throw out in the environment.
Fragile.
Manufacturer.
5
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
1.3. TECHNICAL SPECIFICATIONS
The technical specifications for MacroVIEW DM are described as follows:
PC panel slim 17” (CODE 372480):
CPU:
Intel® Core™ Duo processor SU9300 (3M Cache, 1.2GHz, 800 MHz Fsb)
Memory: 4 GB DDR3 RAM
HDD: 500GB Hard Disk 5000 RPM 24x7
Display:
17” TFT color LCD
Max resolution 1280x1024 pixel
16.2M colors
Viewing angle 140/130°
Luminance 300 cd/m²
Contrast 500:1
Resistive touch screen
Connections:
Serial ports: 1xRS-232
3xUSB 2.0
1xDVI
2xSpeakers
2x10/100/1000 Ethernet LAN RJ45
1x Wi-Fi-LAN wireless 802.11 a/b/g Medical
PC Panel:
Operating system: Microsoft Windows 7
Dimensions (W x H x D): 436.5 x 376.5 x 91.5 mm (17.18" x 14.82" x 3.60")
Weight: 8kg (17.6 lb)
Mounting VESA 75x75 mm, 100x100mm
NOTE: NO BUILT-IN CD/DVD READER/WRITER
Manipulator Unit (CODE 372370):
CCD 9.0 Mpx
Optical zoom 10X with image stabilizer
Auto white balance
Additional 58mm macro focus lenses: +1,+2,+4
Built-in microphone
5.6” LCD color monitor
Keypad for camera control
4W LED illuminator
Chassis color: RAL9010
Cart (CODE 372483):
Wheels cart with battery up to 8 hours working
Li-Ion Battery cart 25.9V / 18Ah / 466.5Wh
USB 2.0 ports (x2)
Spring arm L800mm + 600mm extension (L31.5’’+23.6’’)
Arm: Adjustable pole (vertical) 1500mm–2200mm (59.1’’-86.6’’)
Power supply:
Power Input: 100–240V~ 50/60Hz, 1.6–1.0A
6
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
1.4. TRANSPORTATION AND STORAGE CONDITIONS
Ambient Temperature: +10°C to +40°C.
Air humidity: 30% - 75%
Air pressure: 700mbar – 1060mbar
1.5. WARNING
Should the equipment be used in different ways than those specified by the manufacturer, the warranty
provided by the manufacturer may be void.
The panel unit shall be connected only to 3-pole earthed main socket outlet (Protective earth must be
provided).
The Main plug is considered as disconnecting device.
Equipment shall be connected to the main socket outlet which is accessible and visible by the operator.
Equipment is not provided with replaceable fuses. If the system is not properly working, please contact your
distributor or Milestone.
All the parts of the equipment and all the accessories shall be exclusively supplied by the manufacturer.
For waste disposal of electric and electronic equipment see Chapter 8
In case of malfunction, please turn OFF the computer and start it again. If the system is still not properly
working, please contact the distributor or the manufacturer.
DO NOT OPEN ANY COVER If the equipment is not working properly, please contact
the local representative or manufacturer.
1.6. REMOVAL OF EQUIPMENT FOR REPAIR
1)
2)
3)
4)
5)
6)
Switch OFF the panel PC. Disconnect the main plugs of the panel PC from the main socket outlets
Switch off the camera power supply. Disconnect the main plug of the camera power supply from the
main socket outlet.
Disconnect all accessories (keyboard, bar-code reader…).
Clean and disinfect all parts of the equipment according to the manufacturer specifications.
Put all parts of the equipment into the packing supplied by the manufacturer (original packing).
Send device to the manufacturer for repair.
It is very important to switch OFF the PC panel of the MacroVIEW DM before
disconnecting the manipulator.
Besides the CDs of the MacroVIEW DM software, Milestone will also provide for each
unit genuine Microsoft Windows 7 CDs or the USB Recovery key. We strongly
recommend that each user takes all the necessary steps to assure that the original
CDs or the USB Recovery key provided with each unit are kept in a safe place, as
Milestone is not in a position to supply other CDs, or USB Recovery key or copy of
them. A copy, if available, is not covered by Milestone Warranty.
The Microsoft Windows XP license number is on backside of the PC Panel, on the
Genuine certificate/stick.
7
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
1.7. ANTIVIRUS
Milestone suggests installing an antivirus software. Milestone does not install antivirus so that you can
choose your preferred version according to your needs.
Pay attention when setting the Antivirus so that data flow on the USB protocols and accesses to the Hard
Disk are not limited.
1.8. BACKUP MacroVIEW DM DATA (IMAGES OF THE CASES)
Milestone strongly suggests storing the cases’ images on a server with an automated
backup procedure.
Contact your local Network/IT Manager.
The dimension of images with the suggested settings is 2MB/image.
1.9. MILESTONE REMOTE CONNECTION
MacroVIEW DM software is provided with Milestone Remote Connection that enables our Customer Support
to manage the unit from Milestone headquarters. To get Remote Connection it is necessary that the PC is
connected to Internet. Then contact [email protected] and communicate the following
data:
-
Serial number of the unit,
Version of the remote connection software,
ID,
Password.
The connection can be established only if the GREEN icon appears:
1.10. MARKING PLATES FOR MacroVIEW DM
Marking plates of the Panel PC – Cameras – Monitor and power supply:
For explanation of symbols see Chapter 1.2
8
Milestone s.r.l.
2.
MM079-006 – MacroVIEW DM – Operator Manual
MACROVIEW DM INSTALLATION
Installation and preliminary operations are illustrated in this section. We recommend you to read carefully the
following paragraphs before operating MacroVIEW DM.
2.1. UNPACKING CHECK LIST
When unpacking check that all parts correspond to the shipment which includes:
MacroView DM (Digital Mobile)
CODE 372470 Mobile Macro Digital Imaging System for Autopsies and
Forensic Studies with stand-alone battery operation.
Complete system includes:
A.
POINT-OF-CARE CONTROL TERMINAL (CODE 372480)
Touch Screen Control terminal with OS Windows 7 Ultimate, 17" TFT LCD 1280x1024 Max. 16,2M
colors:
Intel core 2 Duo processor SU9300 (3M Cache, 1,2GHz, 800 Mhz Fsb)
4 GB DDR3 RAM
500 GB Hard Disk 5000 RPM 24x7
2 x Gigabit Ethernet interface (RJ-45)
Spill and dust resistant front panel IP 65 - NEMA 4 compliant
Touch pen
Safety according to CE, FCC, UL
USB 2.0 ports (x3)
Sizing Ruler (CODE 40219)
Wi-Fi 802,11 A/B/G (*)
(*) Subject to restrictions of use according to local Radio Frequency regulations to be checked before
enabling this functionality.
B.
MOBILE SUPPORT FOR IMAGING UNIT (CODE 372483) with:
Wheels cart with battery up to 8 hours working
Spring arm L800mm + 600mm extension (L31.5’’+23.6’’)
Adjustable height
USB 2.0 ports (x2)
USB 2.0 ports (x2)
9
Milestone s.r.l.
C.
MM079-006 – MacroVIEW DM – Operator Manual
IMAGING UNIT (CODE 372370) complete with:
Camera with antisplashing enclosure with special connection for camera’s holder.
10X optical zoom Digital Camera with auto Iris and autofocus
Resolution: up to 9MPixels
Complete with 1x, 2x, and 4x, close up lenses
Built in microphone
Built in objective LED ring light for spot illumination
Display Monitor -5.6” – TFT/LCD – Full Color
Hand Control Panel – Camera holder with zoom, save features and Audio-Video Recording
Display Monitor and Hand control with camera
Built-in
microphone
This Monitor allows easy orientation of the camera to the
position required.
Keypad integrated in the manipulator to control the camera.
The keypad integrated in the manipulator has several buttons with different functions
Microphone
Audio rec
Video rec
Led light
Saving images
Zoom out
Zoom in
Camera switch
D.
MacroView D proprietary software and license including:
Digital imaging acquisition in JPG format, annotation capabilities (sizing, blocks sampling, free hand
drawing), voice recording in MP3 format, possibility of zooming in images already saved for detailed
examination. (CODE 371097)
E.
USB Water proof (sealed) keyboard with Touchpad with IP68 protection against water and dust
(CODE 372352, US format, contact you distributor for different languages available).
F.
USB Bar code reader (includes holder) (CODE 370059)
10
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
Please notice that MacroVIEW DM auto-sizing tool is strictly related to the calibration
done by the operator and not controlled by the software of the unit. For this reason,
sample measurements obtained with MacroVIEW DM auto-sizing tool are NOT TO BE
CONSIDERED AS DIAGNOSTIC values.
It is therefore necessary to carry out such measurements by either positioning a ruler
by the sample (see picture below) or using a caliper to obtain a diagnostic value of the
tumor growth, lesion extension etc…
Before measurement with MacroVIEW DM system, please make the calibration of the
system (see Image measure calibration). If the calibration is not properly performed
and if the measurement control using a secondary measurement tool (like ruler,
caliper) is not carried out, the sample measurements obtained with MacroVIEW DM
auto-sizing tools are NOT TO BE CONSIDERED AS DIAGNOSTIC values.
11
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
2.2. MacroVIEW DM INSTALLATION
Installation is illustrated in this section. We recommend reading carefully the following paragraphs before
operating with MacroVIEW DM.
2.2.1. Macroview DM dimensions
The MacroVIEW DM dimensions are shown in the pictures below:
1400mm
1500mm
2200mm
The cart Length: 610mm
The cart Width: 620mm
The maximum extension of the arm is 1400mm
620 mm
610mm
The maximum extension of the pole support arm is 2200mm from the ground.
The minimum extension of the pole support arm is 1500mm from the ground.
The monitor mount permits a vertical tilt of ±15° and horizontal rotation of ±20°.
12
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
During the shipment, MacroVIEW DM pole support of the swivel arm is completely lowered. Unscrew the
black handle and by hand raise-up to adjust the height of the pole support according to user’s requirements.
2.2.2. Installing the fuse and the battery
The cart’s fuse is not inserted for shipment. The fuse is enclosed for delivery and needs to be attached in the
lower part of the cart as mentioned below, before you can use the cart.
Insert the
fuse here
When you will receive the unit, It is required to leave the battery charging for at least 12 hours, before
starting operating with the unit.
When you connect the cart to the power, verify that the led “Power” is ON (green color), as shown below. If
not press the ON/OFF button (fast click) of the cart showed by the arrow below.
The cart battery loading is displayed by 3 blu leds showed above that switch on one after the other
continuously. Please refer to the chapter 3.6 to have more information about the panel of the cart.
When fully charged, the battery can operate for up to 8 hours in continuous.
13
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
2.2.3. Camera lens setup
MacroVIEW DM camera kit is supplied with three different lenses: “+1”, “+2” (default) and “+4” close up.
By using the three lenses, it is possible to modify the maximum and minimum fields of view. The lenses need
to be fixed on the camera objective.
Screw the lens on the support of the camera as shown (left figure below):
+1
+2
+4
Three different lenses
+1, +2 and +4 along
with their safety box.
The following table highlights the different fields of view in relation with the different lenses (right figure
above) and distances of the sample from the objective of the camera.
GUIDE FOR DETERMINING THE DISTANCE OF THE CAMERA FROM THE SPECIMEN
AND TYPE OF LENS USED
CAMERA MODEL: SX110
Lens
Neutral (none)
+1
+2
+4
Distance allowed
Minimum
Maximum
97 cm
More than 3m
50 cm
108 cm
34 cm
52 cm
22 cm
24 cm
We suggest installing the objective of the camera at 40cm (18inch) from the working surface using a +2 lens
The automatic autofocus capability of the camera depends on the environmental
conditions. The values reported above are experimental results taken with tests done
in Milestone histopathology laboratory at 100% of zoom level.
14
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
2.2.4. Control module PC panel setup
There are 3 control buttons on the rear side of MacroVIEW DM PC Panel (figure below):
Press the button MENU to display and modify the
following options:
BRIGHTNESS
CONTRAST
COLOR
Use the button SET to modify (+ or -) the settings
of the above options.
2.2.5. PC panel connections
In the figure below PC panel connections are shown.
C
A
A
C
PC-Panel
main switch
Keyboard
LAN
connections
Manipulator
Power supply
15
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
2.2.6. Installation and connection of the wired full total body camera (optional)
TO
MOBILE
PC
POWER
SUPPLY
The hospital technicians have to predispose the power supply for the wireless total body over the ceiling (the
electric scheme is in the following draw). It is required for safety, that the wired camera is switched ON/OFF
trough a main stitch to be provided in the building of the forensic room.
CEILING
SOCKET
WALL
SOCKET
The Miniature circuit breaker also can be a 16A-curve C, in any case: interrupt capability equal or more than
4500A.
The PC-panel must be shut down before turn off the Main switch.
In order to prevent malfunction for Windows operating system Milestone suggest:
To turn on:
1.
2.
3.
4.
Turn ON the PC-Panel mobile
turn ON the manipulator
turn ON the wired camera (if present),
start the MacroVIEW-DM software
To turn off:
1.
2.
3.
4.
close the application MacroVIEW-DM
turn OFF the manipulator
turn OFF the wired camera (if present),
shutdown the PC
16
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
This instrument is universal power supply: 100–240V~ 50/60Hz.
The total body camera is fixed at the ceiling and permit to capture images with a different point of view, to
have the complete image of the body lied on the table. So it is possible take complete pictures and videos of
the patients.
The distance from the total body to the patient must be in way that permits to take the
pictures and videos of all the patient body.
The proper distance for the image capturing is according the following image.
h
WxL
The capturing area is related to the distance from the autopsy table. The approximately:
Zoom
0%
100%
Area
Width
W≈¾h
W ≈ 0.01 h
Lenght
L≈h
L ≈ 0.0075 h
17
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
L
W
Example: installation 2100m from the autopsy table, h=2000mm (note: 100mm is for the camera body).
Area
Zoom
Width
Lenght
0%
W ≈ 1510mm
L ≈ 2000mm
50%
W ≈ 530mm
L ≈ 700mm
100%
W ≈ 18mm
L ≈ 23mm
Values for +2 lens.
To mount the wired total body on the ceiling it is required to fix a staff to the total body as shown in the
picture. Fix the total body on the ceiling with 2 screws with the help of drill.
The WIRED TOTAL BODY CAMERA WEIGHT IS 2.5kg.
BRACHET
CEILING
HOLDER TOTAL BODY
TOTAL BODY
Mounting the total body at the false ceiling you have to, according to the hospital technicians, take the false
ceiling panel and make a hole follow the diameter of holder.
18
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
Once the mechanical installation is completed, connect the camera power supply and the wire that permits
the data connection from the camera to the mobile PC:
TO
MOBILE
PC
TO BODY
CAMERA
19
Milestone s.r.l.
3.
MM079-006 – MacroVIEW DM – Operator Manual
OPERATING MacroVIEW DM
Working with MacroVIEW DM is a very easy and friendly operation. All MacroVIEW DM functions are
described in the following paragraphs.
3.1. START THE MacroVIEW DM
1.
2.
3.
4.
Turn ON the PC-Panel mobile (see image below on the left).
Turn ON the manipulator (see image below on the right).
Turn On the wired camera (if present),
Start the MacroVIEW-DM software
Let Windows start up, then double click on the MacroVIEW DM icon on the desktop (figure below).
MACROVIEW
20
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
3.2. OVERVIEW OF SCREEN FUNCTIONS
The following screen is available only for MacroVIEW DM complete software (not for the Viewer)
A
M
B
C
H
D
E
F
I
G
A
B
LIVE
FULL BODY
L
Allows to return to live camera image of specimen (if not used, the
camera has a preset stand-by timer of 300 seconds)
If enabled in the program setting page (see the chapter 3.7.2), it enables
the management of the Total Body Camera (ceiling mounted, option).
If full body not installed, function not available.
C
SAVE IMAGE
“Save Image” of the framed image under the thumbnail “Images”. This
function can also be done with food pedal control or F12 on the
keyboard.
D
SAVE VIDEO
“Save Video” under the thumbnail “Video” on the right side of the screen.
E
CAM SETTINGS
Open the window to change the camera settings: compression,
resolution of the images, split and so on.
F
ABOUT
Provides set-up of working parameters for MacroVIEW DM. It is
accessed by simultaneously pressing "Alt"+"Ctrl" keys and "About"
button. Parameters include measurement calibration, color control, video
source and language setup.
G
EXIT
To exit from MacroVIEW DM application and go back to the computer
operating system.
H
MAIN SCREEN
I
ZOOM STATUS BAR
Area in which specimen image is observed and then saved.
By mouse or touching of the button (from 0 to 100% in 7 steps), to zoom
in/out as required. This function can also be done with foot pedal control
for no-hands operation.
21
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
L
CASE NR.
Requires bar code entry or manual entry by operator to create or retrieve
a patient session.
M
IMAGES AND
VIDEOS
ARCHIVE
Images saved in sequential order are displayed in this area. Allows
displaying of up to 6 thumbnail pictures. Use the “UP” and “DOWN”
button to view other images archived.
It is also possible to use either the keyboard F-keys functions (see the table below) or the hand remote
control for the most important functions; see the table below.
F9
F10
F11
F12
Button
ZOOM OUT
ZOOM IN
SAVE
Function
AUDIO REC: Voice recording, format MP3.
VIDEO RECORDING: Videos to support case descriptions, format: AVI.
LED LIGHT: turn on the led installed round the camera for an optimal grade of light and
avoid shadowed areas.
CAMERA SWITCH: swap the cameras between the wired total body and the live camera
(manipulator). Function is not available if full body camera not installed.
ZOOM OUT/ZOOM IN: to increase/decrease the area of interest that has to be either
photographed (picture) or recorded (video).
SAVE: Capture and store images. Saved images appear as thumbnails on the right of the
PC-panel screen.
22
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
3.3. OPERATING MacroVIEW DM
The following is a simplified procedure for creating a patient working file of specimen images with edits. Start
the software as described in the chapter 3.1).
Create / Retrieve
To create or retrieve a patient file, enter Laboratory
number by barcode reader or manually with keyboard
(in the example enter “Test”, as shown on the left
figure).
On entry of Laboratory number you are ready to
handle and save specimen images. On using manual
entry you will need to press the return key.
MacroVIEW DM is provided with a touch pen which is
on the side of the Controller.
This pen can be used to touch the screen in
substitution of the mouse or finger touch since
MacroVIEW DM is a touch screen system.
Taking Image/Video
Take an image of a specimen by zooming in/out until
you have the desired area of interest, then press the
Save button (either on the screen or on the remote
control).
On saving video (AVI format), user must use the
“Save Video” icon on the left part of the screen. Press
again to stop recording. At the end of rec phase,
select the level of compression among the different
options displayed.
It is also possible to use F9-key (zoom-out) and F10key (zoom-in) followed by “Save” icon (left side of the
screen).
The saved image appears on the right of the screen in
the film library (Thumbnails).
On the “Zoom Status bar”,
press “Focus” to force focus
before taking an image, if
necessary.
23
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
Play the Video
Select the button “Video” (red circle in the
picture) to show all files available for that
case. Then, from the film library on the right of
the screen, click on the Thumbnail of the
video to play.
The Viewer screen will appear and at the end
of the playing, using the corresponding
buttons, it is possible to “Replay”, “Delete” the
video or “Back” to annotation mode.
Images library Scroll UP/DOWN
Press the button UP or DOWN to scroll
up/down the libraries of images/videos taken.
Annotation
To enter the Annotation mode, single click on
the desired picture (see red circle on the
screen)..
24
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
3.4. ANNOTATION MODE
In Annotation mode (see the previous paragraph), it is possible to add text, measures, lines and sections to
the picture, examine the tissue, record audio or directly print out, if a printer is connected to the controller by
USB or LAN.
Click on the desired picture (red circle below) to enter in the Annotation mode: on the left part of the screen
the Annotation tools appear.
Pointer
Click on this icon to activate the pointer and move it on
the line (or section, arrow etc) appearing on the image
to modify it (change its color, thickness etc). See also
Freehand drawing and other following sections.
Examine
Click onto this icon with the mouse or the touch pen.
Point the tissue and click the zoom IN/OUT to
increase or decrease the magnification. Press SAVE
to store the current enlarged image.
The higher is the image resolution, the better are the
enlarged details.
25
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
Sizing
Click onto the ruler icon with the mouse or the touch
pen. Point and drag to the end point of measurement.
MacroVIEW DM is equipped with a moveable camera,
hence it requires a measure reference, obtained with a
ruler, for making the automatic sizing/area. See
section 3.5 for calibrations.
Measure Areas & Free Size
Click and keep the “sizing” icon pressed with the
mouse or the touch pen. The toolbar circled in red will
appear.
Click on “Area” icon to draw an area on the specimen;
the system calculates the area taken.
Click on “Free Size” icon to draw freehand lines; the
system calculates the length of the line.
Please notice that sample measurements obtained with
tool are NOT TO BE CONSIDERED AS DIAGNOSTIC
indicative only.
It is therefore necessary to carry out such measurements
by the sample or using a caliper to obtain a diagnostic
lesion, extension etc…
MacroVIEW DM auto-sizing
values. These values are
by either positioning a ruler
value of the tumor growth,
Freehand
Click onto the Freehand icon with the mouse or the
touch pen. Point and drag to add the freehand curves
on the picture.
26
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
To Draw Lines
Click onto the Lines with the mouse or the touch pen.
Point and drag the desired line on the picture.
Keep holding the button activating the multiple choice
of Squares, Circles, Arrows, Lines or Compass.
Add Text
The addition of text can be made by clicking or
touching onto the Text icon, then point and drag until
the desired text box is made, release and enter
desired text by the keyboard or barcode (see the
arrow).
FAVORITE TEXT: Once the list has been customized,
click on the Text icon and keep it pressed until the list
is displayed: choose the text required to enter it. See
also Chapter 3.7 for the customization.
Add Section
Click onto the Section icon with the mouse or the
touch pen. Point and drag the desired line on the
picture.
Keep holding the button thus activating the multiple
choice of labeling styles (either A, 1, A-1 or 1-A).
27
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
Take representative tissue blocks
Click or touch onto the scalpel icon.
Click onto start point of the block, holding the key
down, drag to the end point of the block and release.
The icon representing the block will appear with the
alphabetic label on the left of the line.
To change to alphanumeric labeling click onto the
buttons at the left/right sides of NEXT SECTION and
select desired labeling code.
Click on the Settings button, a pop-up screen will
appear to modify: annotation and sections text size,
incremental mode, grid on image and line thickness.
The sections/measurement tags will be displayed
either on the “Center” or on the “Side” of the line
drawn.
Audio recording
An audio comment can be added to a saved image by
pressing the Record button.
Press the Record button again to stop the recording.
Press SAVE and then Play if you want to listen the
audio associated to the image.
NOTE: saved audio comments cannot be removed,
but you can only delete a picture along with its audio.
Press Play All to start a presentation of all images of
the case together with their vocal comments.
Undo & Delete
To remove the last edit on the image, press the Undo
button and the last entry on the screen will disappear
(cancellation is done from the last to the first edit).
The Undo feature is not working when the image with
edits has been saved.
Press Delete icon to cancel the selected image with its
notes. The deleted image cannot be retrieved later.
28
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
Print
Select Print Icon and this screen will appear.
By clicking Default, the current image is sent to the
default printer; the system will show the print preview.
By clicking or touching Template, the images will be
exported in a customable form, for example to create
a report.
The form can be filled to generate a report only if
Microsoft Word is available.
Printing of all templates, with the exception of the default template, requires Microsoft
Word or Microsoft Word Viewer installed.
Microsoft Word Viewer is available only in English edition on the MacroVIEW DM CD
supplied with the system. Microsoft Word Viewer allows only the printing of the
generated report, but no modification is possible.
Should you need to access images taken with MacroVIEW DM software with an
external program, like Paint: please copy the images of your interest in an external
directory. Once copied, you can modify, delete etc the copied images.
DO NOT modify nor cancel the images in the MacroVIEW DM directory.
29
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
Save/Exit
When all necessary edits have been made, click or
touch on SAVE icon, as indicated, to save them.
The button SAVE turns to RED when there is at least
a note that has not been saved yet.
Images can also be saved by Hand Remote Control
by pressing the Save command.
Anyway, if Exit to Live icon is pressed and edits have
not been saved, the system will ask if you want to
save them.
When changes have been saved, they cannot be edited e.g. removed.
The original image (without notes) is displayed together with modified images (with notes).
The button SAVE turns to red when there is at least a note that has not been saved yet.
3.5. IMAGE MEASURE CALIBRATION
Because the manipulator of the camera is moveable, the calibration of MacroVIEW DM
unit must be repeated before taking of any new image (of organs or corpse).
Because the Full Body camera in a fixed position, the calibration of MacroVIEW DM
unit should be done only once.
Follow these steps below:
•
Select “Live”, as shown below.
•
•
30
Open or create a dummy case by entering a code/number/name.
Take a picture of ruler at 50% of zoom by pressing the SAVE IMAGE button.
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
•
The image is now added to your library. Clicking on the picture will place you into ANNOTATION
MODE.
•
•
•
•
•
Select the button “Sizing” on the left of the screen.
Keep the “Shift” key (on the keyboard) pressed.
Drag a line on the ruler of, for instance, 100mm (as what you can see on the ruler).
Release the left mouse-button keeping the shift button pressed.
Enter the measurement into the dialog box that appears. In this case, 100mm.
•
Click the “Accept” () button.
Please notice that sample measurements obtained with
tool are NOT TO BE CONSIDERED AS DIAGNOSTIC
indicative only.
It is therefore necessary to carry out such measurements
by the sample or using a caliper to obtain a diagnostic
lesion, extension etc…
MacroVIEW DM auto-sizing
values. These values are
by either positioning a ruler
value of the tumor growth,
31
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
3.6. CHECK THE CART BATTERY STATUS
Check the status of the battery through the control panel, which is positioned in front of the shelf for userfriendly operations.
Description of the parts:
ON/OFF
Power
button
Battery
status
LED
Warning
LED
•
-
Power
LED
ON/OFF Power button
If you fast press this button, the Power LED showed above becomes active (green color); in this case the
battery can be charged if connected to the power and the PC and the camera will be powered by the
battery of the cart.
If you keep pressed this button for 3 seconds, the power LED will be deactivated; in this case the battery
can be charged if connected to the power but the PC and the camera will not be powered.
If you keep pressed this button for 10 seconds, the cart will be completely out of use; in this case the
battery cannot be charged even if connected to the power and the PC and the camera will not be
powered. If you want to switch it on again, remove the power for a few seconds and then connect again
the cart to the power.
To work with MacroVIEW DM the Power LED should be active.
•
Battery status LED:
It shows the status of the battery.
When the battery is charging, the 3 blu leds switch on one after the other continuously.
When the battery is not charging and:
- Only LED 1 and 2 are ON, the battery is < than 80%,
- Only LED 1 in ON, the battery is < than 50%,
- All LEDs are OFF: the battery is <30%.
•
Warning LED:
When the battery is low, the Warning LED is active as explained below:
- if it blinks slowly, the battery status is low.
- If it blinks faster, the battery is very low and the PC is going to switch off very quickly. In both cases it is
suggested to connect immediately the battery to the power.
32
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
3.7. SOFTWARE SETTINGS
Keep “Ctrl & Alt” buttons on the keyboard pressed and click with the mouse on "About" icon (left of the
screen).
The Milestone settings window for the software options appears (figure above on the right).
Set measurement unit, language, image folder where images will be saved etc... as you prefer, by editing the
fields of interest.
Checking the box on the left corner (red circle in the figure), the Milestone Settings can be set as Default for
new users.
Already existing user’s accounts need to be modified as well.
IMPORT/EXPORT OF PROGRAM SETTINGS
To export the software settings from the PC where MacroVIEW DM software is installed to another PC (for
example Viewer, or other accounts of the same PC): press on the keyboard “Ctrl+Alt+S”, the PC creates an
.XML file that you have to copy on an external support (like USB key), to transfer the data to the second PC.
Move to the second PC, insert the external support (USB key), open the MacroVIEW DM software, press
“Ctrl+Alt+D” to import the settings (*) and then retrieve the path where the file is stored.
(*) It is necessary that also the second PC, where the above mentioned settings are
saved, is provided with a MacroVIEW DM complete software package in order to
operate all functions, and not run only as Viewer. For purchasing extra licenses,
contact the local representative or the manufacturer.
33
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
3.7.1. Main Cam
“Main Cam” (figure below, circle): is the setting for the camera mounted on the moveable arm.
Parameters:
MAIN CAM: Leave “Camera 0” selected.
-
CALIBRATION FACTOR: Do not change this value. The frame shows the calibration factor
(according to the value entered in section 3.5 above).
-
FORCE CALIBRATION: Let it “Enabled”: because of the moveable camera, in fact, user needs to
calibrate any new picture taken.
-
TRUST EXTERNAL CALIBRATION: Let it “Enabled”: should user import cases from another
MacroView DM system, pictures will be imported and annotated with their original calibrations.
34
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
3.7.2. Second Cam
“” 2nd camera not present; “” 2nd camera present: is the setting for the Wired Full Total body camera
mounted on the ceiling.
Parameters:
SECOND CAM: If selected enables the management of the Total Body Camera (ceiling mounted,
option).
-
CALIBRATION FACTOR: Do not change the number.
-
FORCE CALIBRATION: It must be set disabled because the position of the camera is fixed (this
camera does need calibration once, unless moved from its original height).
-
TRUST EXTERNAL CALIBRATION: It must be enabled, so that should the user impost cases from
other MacroVIEW DM systems, pictures are brought in and annotated with their calibration.
35
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
3.7.3. Customization
Proceed as follows to modify the configuration settings in this screen: click on the screen option (figure
above) to see and modify the different choices available under “Customization” (blue square):
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
36
Languages: select language desired (default is English). Should any additional language be
required, please contact us.
Minimize/Maximize button: check the box to enable this option. This allows minimizing the program
to the system bar and changing the dimensions of the window.
System unit: to change the measurement unit (mm, cm, inches or pixel).
Auto Live: check the box to return to Live Mode when an image has been acquired and saved.
Auto Annotations: select “True” to open any taken picture directly in Annotation mode.
Titlebar: Edit the title required (e.g. Name of the Laboratory)
Max rec audio (sec): it is the maximum audio recording time (in seconds).
Max rec video (sec): It is the maximum video recording time (in seconds).
Keep last video rec settings: select if you want to keep the compression mode selected at the first
video saving.
Standby after (sec): timer for the standby of the camera, in seconds; it saves the CCD when it is not
used.
Keep last video recording settings: let this box checked to maintain the standard video settings.
Otherwise, once each video has been taken, the system will ask you to set the Compression Level
and the Compression Quality of the video.
Shut down camera on edit: if selected will pause the camera when doing annotations on saved
pictures.
Play all – delay (sec): in presentation mode (“play all” button), it is the time (in seconds) between a
picture and the other, when displayed in sequence.
Color Theme: three different choices for the background, Light, Dark or Milestone colors.
Image folder: where the images will be stored. Can be either a folder resident on the MacroVIEW DM
PC, on a server or PC.
Foot Pedal Switch: is the serial port (named as COMx port ) of the PC to control camera by keypad.
Force double entry: By checking this box, every time you create a patient case, you will be required
two times to enter the patient case name, thus avoiding misspelling and/or errors.
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
APPLICATION TUNING
This section enables the user to customize the width and the height (in %) of the image shown on the
software. We strongly suggest to let 100% visualization. Press “Ctrl+Alt+F1” to restore 100% visualization
(full screen).
It also possible to modify the font size by changing the font scaling factor.
EXTERNAL SERVER APPLICATION
This setting is an integration and allows MacroVIEW DM to start an application when
you close the software.
Milestone Medical Customer Dept. is available for support in the integration with your
case.
3.7.4. Save as default for new users
Check “SAVE AS DEFAULT FOR NEW USERS” box to have current settings saved as default for new
user/s. So, if any new account is added to the PC, this will get the new settings as default.
It is instead necessary to update the settings of ALL OTHER EXISTING ACCOUNTS on that PC, if they also
need to operate with the same settings entered for new account/s.
37
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
3.8. CAM SETTINGS
On the main screen, Live mode (video) active, click on the Camera Settings button on the left side of the
screen to check and modify the different parameters.
Compression quality:
SuperFine:
large file, super-high res
Fine: medium size file, high res (suggested)
Normal: small file, good resolution
Image size:
Compression quality
Resolution
(image
size):
Small
Medium 1
Medium 2
Medium 3
Large (*)
Image dimension (px)
Normal
Fine
Superfine
Image file size
640 × 480
2816 × 2112
2272 × 1704
1600 × 1200
3264 × 2448
92.7kB
679kB
1.4MB
2.2MB
3.4MB
136kB
912kB
1.8MB
2.8MB
4.3MB
178kB
1MB
2.3MB
3.3MB
5.2MB
Milestone suggests setting cameras to save images at compression quality “FINE”
and resolution at “MEDIUM 3”. This is a good compromise between the file size (disk
consumption space) and the quality of the image to report the tissue status.
(*) Should images be used for publications (articles, papers etc), Milestone suggests
to choose quality “SUPERFINE” and resolution “LARGE”.
38
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
ISO:
Auto Exposure (Compulsory): select this option
Manual (DO NOT select this mode)
Vertical Flip: to rotate the image 180°
To overturn the image/video change True/False.
White Balance: (Light Source Selection)
During the installation it is NOT necessary to perform the white balance camera setting. The digital camera
will auto-balance the white according to the light conditions where the MacroVIEW DM has been positioned.
Therefore user has to select the type of light source in the laboratory among these options, in order to
perform the best color contrast:
Auto:
SELECT THIS OPTION IF:
you are not aware of the type of light source of the grossing room
Daylight:
the grossing room is enlightened only by natural light
Tungsten:
the grossing room is enlightened by incandescent lamp
Fluorescent:
the grossing room is enlightened by neon lamp
FluorescentH:
the grossing room is enlightened by neon lamp with yellowish light
Preset:
Not to be used
These modifications take place when the user press “OK”, and it is not necessary to restart the software.
If the second cam is present, start it and redo the settings for the 2nd cam.
39
Milestone s.r.l.
4.
MM079-006 – MacroVIEW DM – Operator Manual
MacroVIEW DM AS VIEWER MULTISTATIONS
4.1. HOW TO INSTALL THE MacroVIEW DM AS VIEWER
MacroVIEW DM Viewer allows simple retrieval of MacroVIEW DM images, using either barcode or manual
entry of patient identifying number. Images can only be viewed and printed (generating report as explained in
the previous chapter), but no modifications i.e. annotations is possible.
To carry out any modification on images (such as add notes, section and so on), an
extra license of MacroVIEW DM software must be available. For this, contact your local
distributor. MacroVIEW DM Viewer is the same software installed on the MacroVIEW
DM unit and it does not need a license. Therefore, user is authorized to install
MacroVIEW DM as Viewer software on any PC.
MacroVIEW DM Viewer can be installed on any personal computer as follows:
1)
Use the MacroVIEW DM CD and open the MacroVIEW DM folder. Click on Set Up installer and
follow the instructions to proceed with the installation of the MacroVIEW DM software.
2)
Should this message appear during installation: “Microsoft Framework 2.0 not installed”: open the
CD, open the folder “Framework” and click on “DotNetFx” and then again on “DotNetFx” installer and
follow the instructions.
4.2. HOW TO MAKE AVAIBLE MacroVIEW DM IMAGES IN A LOCAL AREA
NETWORK
As MacroVIEW DM is a mobile system, the saved cases will be stored into the PC
panel. At the end of every session, we strongly recommend to copy the cases’ folder
into the server, that should be automatically backuped. In paragraph 4.2.1 you can find
the procedure to share the cases with a local network. In paragraph 4.2.2 you can find
the procedure to connect a Viewer PC to the cases stored on the server.
Before proceeding with the instructions below, it is necessary to connect the
MacroVIEW DM PC to a local network and setting it with appropriate parameters. For
more
details
please
contact
our
customer
support
dept
at
[email protected].
40
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
4.2.1. Settings MacroVIEW DM PC
1.
2.
3.
4.
5.
6.
7.
8.
Turn on the MacroVIEW DM PC.
Open the MacroVIEW DM software.
Keep CTRL+ALT pressed and click on
“About” icon on the screen.
In “Customization” area, select “Image
folder” window and click on browse button.
Check the directory path (arrow) and press
OK.
Close MacroVIEW DM Software.
Open Windows Explorer.
Find the folder selected at point 5.
(C:\Program
default)
Files\Milestone
Medicalsrl\MacroPath\IMAGES
is
9.
Click with mouse right key on “Properties”
10.
Select “Sharing”, then “Share this folder on
the network”.
41
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
4.2.2. Settings MacroVIEW DM Viewer PC
1.
2.
3.
4.
5.
Start the MacroVIEW DM Viewer software program.
Press “CTRL+ALT” and click on “About” icon on the screen at the same time.
Select and modify the “Directory” Path.
Select “My Network Places” folder.
Search the MacroVIEW DM unit (the standard name of the PC is MACROVIEW or MILESTONE).
6.
Select the shared folder
7.
At the end, the full path is displayed (for example \\MACROVIEW\images).
“IMAGES” then press OK
If the above steps have been carried out correctly, it is now possible to work from both (or more) working
stations. When a new case is added from histological laboratory, every additional station is able to view and
print the same images.
Milestone strongly suggests storing the cases on a server with an automatic backup
procedure.
Contact your local Network/IT Manager.
42
Milestone s.r.l.
5.
MM079-006 – MacroVIEW DM – Operator Manual
ACCESSORIES (OPTIONAL)
5.1. USB BARCODE READER (INCLUDES HOLDER) (CODE 370059)
Barcode reader to automatically enter the patient/specimen number to open a new file or retrieve an existing
file (figure below).
5.2. WIRED FULL TOTAL BODY FOR MacroVIEW DM (CODE 372401)
This camera allows a full view of the body from the ceiling and of the operator who is doing the surgery.
Technical data: 100–240V~ 50/60Hz, total weight 2.5Kg.
43
Milestone s.r.l.
6.
MM079-006 – MacroVIEW DM – Operator Manual
MANTENAINCE OF THE MacroVIEW DM
6.1. CLEANING OF THE MacroVIEW DM
DISCONNECT THE PLUGS FROM THE SOCKET BEFORE STARTING THE CLEANING
PROCEDURE.
During normal use the PC Panel may become soiled and should, therefore, be cleaned regularly.
Agents: Green tinctured soap and Enzymatic detergents.
Steps:
1. Prepare agent as per the manufacturer’s instructions or hospital protocol,
2. Wipe the PC Panel and the other parts of the Unit with a clean cloth that has been moistened in the
cleaning solution.
Do not immerse or rinse the PC Panel and its peripherals.
If you accidentally spill liquid on the device, disconnect the unit from the power source.
Contact your Biomed regarding the continued safety of the unit before placing it back in
operation.
Do not spray cleaning agent on the chassis.
Do not use disinfectants that contain phenol.
Do not autoclave or clean the PC Panel or its peripherals with strong aromatic,
chlorinated, ketone, ether, or Esther solvents, sharp tools or abrasives.
Never immerse electrical connectors in water or other liquids.
6.2. SUBSTITUTION OF THE BATTERY
Battery shelf-life is 2 years. Call your Technical Assistant to substitute battery.
For disposal of battery, see Chapter 8.
44
Milestone s.r.l.
7.
MM079-006 – MacroVIEW DM – Operator Manual
TROUBLESHOOTING THE MacroVIEW DM
7.1. MANIPULATOR KEYPAD DOES NOT WORK
Open “Software settings” by Keeping “Ctrl+Alt” buttons on the keyboard pressed and click with the mouse on
"About" icon
. Look at the COM associated to the Manipulator (named as Foot Pedal Switch): in the
example below the red circle identifies COM6.
Never use the COM4 port (this is reserved to the Touch Screen Monitor).
From the Windows “Start” menu, go to “Settings”, click on “Control Panel”, open it and select “System”.
45
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
Select “Hardware” folder
then press “Device Manager”.
From the list expand “Ports (COM e LPT)”:
Please check that there is only one USB serial port. In this case, there are two USB-COM ports that you can
choose (see the figure above). To identify the proper USB serial port displayed: disconnect all USB devices
except the Manipulator switch and press the “Hardware Update” (see below).
46
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
Please check that there is only one USB serial port (figure below). In this case, this is the COM port that you
have to choose in the Settings of the MacroVIEW DM (in the example, COM 5).
If
any
USB
serial
port
is
displayed:
[email protected].
please
contact
our
Customer
Support
at
47
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
7.2. TOUCH SCREEN RECALIBRATION
Problem description: you touch the monitor with the pen, but mouse arrow moves to another direction on the
screen. In this case, it is necessary to recalibrate the touch-screen as follows:
•
Exit from MacroVIEW DM software.
•
From the “Windows” screen select “TouchKit”
then “TouchKit” and select “Configure Utility”.
icon or from the “Start” menu, go to “Programs”,
The following screen appears.
•
•
48
Press “Setting” (see red square above).
Press “Option” button and verify that the “Enable Auto Touch” is not checked (see the image below).
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
•
Press OK to close the windows. Choose the “Tools” folder (see the circle below).
•
Press “4 Points Calibration” (see the arrow above).
•
Now the green target appears: with the pen pointer (CODE 330055) touch on its centre. Repeat for
all the green targets that are displayed.
At the end, a message appears to advise that the calibration is completed, press “OK” to continue.
The recalibration is now completed.
49
Milestone s.r.l.
MM079-006 – MacroVIEW DM – Operator Manual
7.3. DIRECT PRINTING CONFLICT
If MacroVIEW DM camera model SX110 does not allow to print images to CANON photo-direct printers
(models that can print images with camera directly connected to the printer, also without PC) and if the
printing-process of images or complete report is aborted: shutdown the camera using the switch provided on
power supply/transformer.
To get MacroVIEW DM restart working with the camera: TURN-ON the camera again before pressing “LIVE”
button.
7.4. COPY TO USB CONFLICT
If MacroVIEW DM camera model SX110 does not allow to transfer data from/to USB removable disks and if,
when you try to copy data from the MacroVIEW DM unit to USB-DISK, the operating system shows you a
message similar to “Preparation of copy in progress…” : shutdown the camera, using the switch provided on
power supply/transformer.
50
Milestone s.r.l.
8.
MM079-006 – MacroVIEW DM – Operator Manual
WASTE DISPOSAL
8.1. WASTE DISPOSAL OF MacroVIEW DM UNIT
Removal of equipment from use for disposal:
1)
Switch OFF the panel PC. Disconnect the main plugs of the panel PC from the main socket outlets.
2)
Switch off the camera power supply. Disconnect the main plug of the camera power supply from the
main socket outlet.
3)
Disconnect all accessories (keyboard, bar-code reader, camera…..etc).
4)
Clean and disinfect all parts of the equipment according to the manufacturer specification.
5)
Dispose all electric and electronic parts of the equipment according to the manufacturer:
Complying with directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on
waste electrical and electronic equipment (WEEE), the separate collection environmental managed of
equipment is mandatory.
It is necessary to return the used equipment to the distributor or to inquire about the presence of a local
empowered system for collection and disposal of WEEE.
The in-observance of Directive 2002/96/EC or of the local law which acknowledge it can have potential
effects on the environment and human health
This symbol indicates separate collection
for electrical and electronic equipment
8.2. WASTE DISPOSAL OF BATTERY
Lithium-ionen batteries should be disposed in compliance with all federal, provincial and local government
regulations.
51
Milestone Srl - via Fatebenefratelli 1/5 - 24010 Sorisole (BG) - Italy
MILESTONE
H E L Phone
P I N +39
G
P A T I E N T S
035 4128264 - Fax +39 035 575498
e-mail: [email protected] - web: www.milestonemedsrl.com