Toll-free: 1800 108 1200 I For service: [email protected] I Website: www.godrejsecure.com
Connect with us:
/GodrejSecure @godrejsecure
The contents and information on the catalogue is for general purposes and is provided on "as is" basis. The recommendations of level of
strength are relative and completely depend on the nature of tools used for any attack. All safes can be broken open given sufficient time,
tools, torch (Basic or simple home tools) expert skill and access. All warranties, recommendations and representations of any kind
mentioned herein are disclaimed, including the implied warranties of merchantability and fitness for a particular use. The Company disclaims
any claims, losses, demands, or damages of any kind whatsoever arising out of or resulting by reason or in consequence of any illegal
breaking open of Home / Office Safes, Video Door Phones, Burglar Alarm Systems, or any theft, fire, robbery, fraud or other wrongful act
done by any third Party with regard to Home / Office Safes, Video Door Phones, Burglar Alarm Systems including but not limited to direct,
indirect, incidental, or consequential loss or damages, compensatory damages, injury, economic loss, or otherwise resulting from theft, fire,
robbery, fraud or other wrongful act done by any third Party. The specifications, prices and features of the products may be changed at the
sole discretion of the Company without prior notice.
ISO 9001:2008/ISO 14001:2004/ BS OHSAS 18001:2007
GSS/Viscomm/B2CCommercial/Aurum Instruction Manual/April2016/V1
Godrej & Boyce Mfg. Co. Ltd.
Head Office: Plant 17, Pirojshanagar, Vikhroli, Mumbai 400 079 INDIA.
Fax: +91 22 6796 1509
INSTRUCTION
MANUAL
INDEX
RECOMMENDATIONS
DAMAGE IN TRANSIT
Before dispatching from the factory, all articles are carefully examined and securely packed by
expert packers. In order to avoid damage, all articles are loaded by our trained men. Goods are
likely to be damaged while in transit and/ or when unloaded at destination. This is due to
manhandling during loading and unloading from the truck/rail wagon. Therefore, we request you to
instruct the stakeholder to ensure that the unloading is done carefully.
•
RECOMMENDATIONS..............................................................................................1
•
INSTRUCTIONS FOR OPERATING GODREJ LOCKS................................................2-3
•
COMBINATION LOCK (DELTA LOCK).......................................................................4-5
•
COMBINATION LOCK (LA GARD MECHANICAL)....................................................6-10
•
BIOMETRIC LOCK (SECURAM)...............................................................................11
UNPACKING AND LEVELLING
•
WARRANTY CARD...................................................................................................13
The safe should be unpacked only after it is taken to the site for smooth operation of the door.
Before using the safe, make sure that the surface is levelled. To do the same, you need to stuff paper
packing wherever required.
As we take all the necessary precautions to keep the product safe while dispatching, we do not
accept any liability for damage inflicted in transit.
KEYS
(Packed inside the safe. To open the safe, turn the bolt handle)
DON'T keep the Duplicate Key in the safe itself. Keep it in a sealed cover or keep it somewhere else
in a safe place. Note down the number of the key as reference; it will be required to issue a duplicate
key incase the original is misplaced/lost.
DON'T keep both the keys of the safe in the same bunch. In this way, you will always have one key
as a backup in case you lose the original. The safe can thus be operated in joint custody, enabling
one to operate the safe in absence of the owner.
DON'T expose the safe to rain water while in transit. Cover it up with tarpaulin or water proof paper.
Safes need special protection as their fire resisting capability is likely to be affected by water. Safes
in basements or on ground floors must be placed on stands to keep them safe from water.
DON'T paste paper labels on the safe as the sticker glue of the label contain water. Paint letters
instead, or preferably use our label holder (or engraved) name plate.
OILING SAFES
Oil the pivots, especially the upper atleast once a month over the upper lug. There is a hole provided
to oil the pivot
1
GODREJ & BOYCE MFG. CO. LTD.
GODREJ & BOYCE MFG. CO. LTD.
INSTRUCTIONS FOR OPERATING GODREJ LOCKS
INSTRUCTIONS FOR OPERATING GODREJ LOCKS
"APPLICABLE ON 49, 61 AND 81 DEFENDER AURUM SAFES AND
61 DOUBLE DOOR DEFENDER AURUM SAFES"
"APPLICABLE ON 26,31 AND 41 DEFENDER AURUM SAFES"
CLOSING
LOCKS
UPPER
LOCK A
LOWER
LOCK B
First
Operation
Second
Operation
First
Operation
Second
Operation
Key A-1
Key-2
Key-2
Key A-1
Turn
Key B-1
Turn
Turn
Turn
Key-2
Turn
Key-2
Turn
•
Keys of the above mentioned safes are marked with prefix "SP"
GODREJ Safes are supplied in unlocked condition at the time of delivery
Key B-1
Second
Operation
First
Operation
Second
Operation
Key -1
Key -2
Key -2
Key -1
Turn
•
OPENING
First
Operation
LOCK
Turn
•
2
CLOSING
OPENING
Turn
Turn
Turn
GODREJ Safes are supplied in unlocked condition at the time of delivery
Turn
3
DELTA LOCK
Operating and changing instructions for Delta Make 3 wheel Mechanical Combination Lock
Model: LK 1200 for 3 Wh. Comn Lock
Model: DR 2300L for Front Reading Dial With Dial Lock
Model: DR 2300 for Front Reading Dial Without Dial Lock
OPENING THE LOCK USING THE OPENING INDEX
If the safe comes with a factory-set combination on 50, turn the dial
to the left and pass the number 50 four times. Then align it with 50 on
the opening index. Turn RIGHT until the dial stops. The combination
lock bolt will retract and the safe can be opened.
To open Lock with a previously-set combination, for example, 10-2030:
Changing Index.
Turn the Change Key to the RIGHT until it stops (approximately one-quarter turn). Leave the key in
the lock. Select a new combination, such as 40-50-60. Never select a number from 0 to 20 (the
forbidden zone) as the last number of the combination.
Using the CHANGING INDEX this time, turn the dial to the LEFT and pass 40 three times and stop
exactly on 40 the fourth time on changing index.
Turn the dial to the RIGHT and pass 50 two times and stop exactly on 50 the third time on changing
index.
Turn the dial LEFT and pass 60 once and stop exactly on 60 the second time on changing index.
Leave the dial on 60.
Now turn the Change Key to LEFT until it stops and REMOVE the key.
Completely dial the new combination, 40-50-60, on the OPENING Index, several times to make
sure the combination lock opens before you shut and lock the door off the safe.
After changing, always dial the new combination and retract the combination lock bolt several
times before shutting and locking the vault or safe door.
Turn the dial to the LEFT at least four times completely to clear the
combination lock to accept the combination.
NOTE:
Using the OPENING index, turn the dial LEFT and pass the first
number of the combination, 10, three times and stop exactly on 10
the fourth time.
•
Turn dial to the RIGHT and pass 20 two times and stop exactly on 20
the third time.
Turn the dial LEFT and pass 30 once and stop exactly on 30 the
second time.
Turn the dial to the RIGHT. When the lock is open, the dial will not turn
to the right anymore.
To lock the combination lock, turn the dial four times completely to
the LEFT.
CHANGING THE COMBINATION ON THE CHANGING INDEX
To change the combination, you will need access to the existing combination and a change key.
To change the combination, you must first open the safe door by dialing the combination, 10-20-30.
With the bolt fully retracted (Lock open), before changing combinations, verify that the dial stops at
'0' on the opening Index.
OPERATION AND CHANGING INSTRUCTION (continued)
Operating and changing instructions for Delta Make 3 Wheel Mechanical Combination Lock.
Next dial the existing combination 10-20-30, as described previously, on the CHANGING INDEX,
but STOP the dial on 30 which is the last number of the combination.
In the back of the door, insert the Change Key into the key hole. If the Change Key does not go in,
the wheels are not lined-up in order to be changed, and you must dial the combination again on the
The lock bolt must move freely in the lock body.
•
Pressure against the lock bolt should be avoided.
•
While setting or operating of lock, the direction of rotation of Dial should be uniform.
LA GARD MECHANICAL
stops. (Figure 2.) Leave the change key in the lock while setting the new combination.
5. Next turn the dial to the LEFT (CCW) at least four complete rotations to clear the lock. The lock is
now ready to accept the new combination.
Group 1, Group 2 & Group 2M Locks
CAUTION: Do not spin the dial to clear the lock.
OPERATING & CHANGING INSTRUCTIONS
OPEN LOCK WITH THE FACTORY
COMBINATION
6. Set the new combination using the CHANGING Index:
EXAMPLE COMBINATION: 10-20-30
CHANGING INDEX
OPENING INDEX
LA GARD mechanical locks are shipped with the factory
combination of 50. Open using the opening Index:
4x
Turn dial to the LEFT (CCW) passing "50" three
times. Then stop exactly on the number "50"
the fourth time.
Turn the dial to the RIGHT (CW) until it stops and
the bolt retracts.
4x
Turn the dial LEFT (CCW) passing the first number in the combination V-/* (10) three times.
Then stop exactly on the number "10" the fourth time.
3x
Turn the dial RIGHT (CW) passing the next number in the combination ^ (20) two times.
Then stop exactly on the number "20" the third time.
2x
Turn the dial LEFT (CCW) passing the last number in the combination (30) one time. Then
stop exactly on the number "30" the second time.
7. Hold the Dial to prevent movement and turn the change key to the LEFT (CCW) one quarter turn.
8. Remove the change key. The new combination is now set.
Figure 1
ALWAYS perform the combination test with the safe door open!
Test the new combination several times using the opening procedure below.
OPEN LOCK WITH A SET COMBINATION
NOTE: Variations in the alignment of the dial ring during installation could cause the Factory
Combination of 50 to vary slightly, either up or down by one or two numbers.
NOTE: If using the VisionGard Dial (2085 or 2090 Series) and a lock with the factory combination,
the lock will open on 47.
NOTE: When dialing a combination, if you passed the number on which you intended to stop, you
cannot reverse the dial to correct. The opening procedure must be repeated from the beginning.
SET COMBINATION
To change the combination, you will need to know the existing combination and have a LA
GARD change key (P/N 1307).
Dial the set combination using the OPENING Index. EXAMPLE COMBINATION: 10-20-30
4x
Turn the dial LEFT (CCW) passing the first number in the combination V-' (10) three times.
Then stop exactly on the number "10" the fourth time.
3x
Turn the dial RIGHT (CW) passing the next number in the combination (20) two times. Then
stop exactly on the number "20" the third time.
2x
Turn the dial LEFT (CCW) passing the last number in the combination V-J (30) one time.
Then stop exactly on the number "30" the second time.
Turn the dial to the RIGHT (CW) until it stops and the bolt retracts.
CAUTION: When selecting a combination, choose a three number sequence from 0 - 99. NEVER
select numbers 0 to 20 as the LAST NUMBER of the combination. This is the "Forbidden Zone" and
can cause the lock to malfunction. For security purposes, do not select a combination from
Figure 2
personal data such as birth date, phone number, etc.
NOTE: When locking the safe, always turn the safe handle to the locked position (bolts extended)
before turning the lock dial four complete rotations to the LEFT (CCW) to relock. If you notice any
resistance, DO NOT force the dial to turn. This may cause damage to the lock.
1. Dial the existing combination using the CHANGING Index. (Figure 1.)
2. STOP the dial on the third number of the combination.
3. Insert the change key into the change key hole. (Figure 2.)
(P/N) 723.069 Rev B 01/11 • © copy right 2009-2011
Kaba Mas LLC
NOTE: If the change key does not go in easily, the wheels are not
aligned. Repeat steps 1-3.
4. Turn the change key to the RIGHT (CW) one-quarter turn until the key
6
GROUP 2 & 1
COMBINATION LOCKS
7
extends at any point during the installation
procedure: the bolt may be retracted by following
the Retracting the Lock Bolt instructions on page
two
INSTALLATION INSTRUCTIONS
Complete all welding work on the safe before installing the lock.
Keep metal dust, filings, etc. away from the lock.
Never oil, grease, lubricate or paint the lock.
If possible, keep cables away from sharp edges and moving parts.
If possible, never lift the lock by the cable.
Figure 2
Optional hardplate
or mounting bracket
SPLINE KEY POSITION CART
Total Mounting Thickness
(plus. 875")
Group 2M Mechanical Lock (3390 Series) INSTALLATION INSTRUCTIONS
LH
The lock can be mounted in four positions by aligning the spindle
groove with the corresponding cam position. The positions are
marked as follows:
VU
RH (right hand) Lock bolt should point right as you face the back
of the door.
RH
L
LH (left hand) Lock bolt should point left as you face the back to
the door.
1. If required, locate, drill and tap the two holes to mount dial ring, the spindle, and three holes to
mount the lock assembly on the inside of the safe door. Use the installation template (P/N
740.118) available online at www.kaba-mas.com
2. Attach the lock assembly to the door using the three US mounting screws provided. Tighten the
mounting screws to a torque setting of 30in./lbs. (3.4Nm). Insert short mounting screws into the
hole with marking (Figure6). This screw should not be removed during servicing of the lock.
LAGARD mechanical locks are shipped with the factory
combination of 50. To open:
NOTE: Ensure the lock assembly spindle hole is properly aligned with its spindle through the
hole in the safe door.
1. Turn dial to the LEFT (counter-clockwise) passing 50
atleast +four times.
Figure 5
VD (vertical down) Lock bolt should point downwards.
L
+
Figure 7
U
V
A H
8
2. Stop when 50 lines - up with the Opening Index (Figure3).
3. Turn RIGHT(clockwise) until dial stops, this will retract the
bolt. (This may vary slightly by one or two numbers either
up or down due to variations in alignment of dial ring during
installation.)
H
V D
Retaining
Screw
H
V D
NOTE: It is recommended to keep the lock bolt in the retracted position throughout the
installation procedure, It prevents interference by the boltworks during installation. To ensure
this, keep one finger over the bolt while mounting the lock and installing the spindle. If the bolt
Figure 4
VU (vertical up) Lock bolt should point upwards.
L
3. Measure total mounting thickness (door thickness + mounting plate) (Figure2).
4. Cut the spindle to a length of .875" (23mm) plus the total mounting thickness.
5. Mount the dial ring from the centre, and the through hole. Attach it to the safe door using the two
mounting screws supplied with the dial assembly. The opening index reference mark must be in
the twelve o'clock position (Figure3).
VD
H
V D
Hardware Pack, Metric (P/N704003)Includes
2. Spline Key (P/N1712)
3. Mounting Screws (P/N 705006 - Qty. 2)
4. Mounting Screw (P/N 205014)
5. Change Key (P/N 1307)
4
U
Group 2M Mechanical Lock (3390 Series)
Hardware Pack, US (P/N704004) Includes
2. Spline Key (P/N1712)
3. Mounting Screws (P/N2930-Qty.2)
4. Mounting Screw (P/N1819)
5. Change Key (P/N1307)
6. Insert Cover (P/N705002)
2
V
1.
2.
3.
4.
5.
3
6
6. Insert the spindle through the spindle hole of the
door. With the bolt retracted, carefully thread the
spindle (clockwise) into the drive cam until it is
tight. Next, rotate (counter clockwise) at least 1/2
turn until the groove in the spindle is aligned with
the correct spline position. (Refer to the Spline
Key Position Chart - Figure4).
7. Insert the spline key fully by tapping it into place
with a screwdriver using insertion notch
(Figure5).
8. Install Cover Insert (P/N 705002), Figure 8. Press
Figure 3
the Insert into the cover it using even pressure.
The insert is designed to prevent Spline key
movement. Once installed do not attempt to
remove the insert. Remove the back cover to service the lock: this will not void the factory
warranty.
A H
SAFEGUARD FOR MOUNTING
5
1
OPENING INDEX
A H
Read the guide carefully before beginning with the installation.
CHANGING INDEX
U
3390 SERIES GROUP 2M LOCK
V
LA GARD MECHANICAL
Figure 6
NOTE: If using the VisionGard Dial (2085 or 2090 Series) and lock with the
factory open on 47.
Figure 8
9
RETRACTING THE LOCK BOLT
ScanLogic D22
The 3390 Series Group 2M Mechanical lock is shipped with the bolt in the retracted position. If the
bolt becomes extended during the installation process, It can be retracted before splining the lock.
SecuRam
To retract the bolt:
1. While viewing the back of the lock, insert a small flat object, such as a screwdriver, into the
spline notches in the cam, in order to rotate it.
2. Rotate the cam to the right (clockwise) at least 4 complete times.
3. Then align the mark on the drive cam with the one on the back cover (Figure7). (Mechanical
tolerance +/- the width of the of the case alignment mark.)
SecuRam. Security You Can Trust. Ram Tough.
•
4. Rotate the cam to the left (counter clockwise) until the bolt is retracted (approximately 1/2 turn).
5. Holding the bolt in the retracted position, the spindle can now be threaded into the cam without
the cam rotating. Insert the spline key using the spline key position chart.
•
•
Design Parameters for 3390 Series Locks
•
1. Bolt dimensions (nominal): .312 inches x 1.000 inches/ 8 x 25.4 mm
•
2. Bolt dimensions (nominal): .355 inches/9.0mm
3. Bolt extension: .485 inches/12.3m
4. The spindle hole diameter can be a minimum of .406" (10.3mm) to a maximum of .438"
(11.1mm). The .406" (10.3mm) diameter is recommended. Spindle hole must be debarred.
5. The lock mounting screws (1/420 or M6) require tapped holes: the recommend depth is
375"(9.83mm), but a minimum depth of 250"(6.35mm) is required.
6. When mounting the lock unit (i.e. integrating it in a bolt work), make sure that the lock bolt has
clearance to freely move to it send positions and that the shifting force works only in the axial
direction (direction of movement).Lateral forces should not be exerted on the lock.
7. Maximum load movable by the bolt: 5 lbs. (22N)
NOTE: 3390 dead bolt lock may not open If more than 5lbs.(22N)of force is applied to the end or
side of the bolt
R
•
•
•
•
•
•
•
•
8. Maximum load against bolt when thrown (all directions) should be:224.8lbs.(1kN)
•
9. If other parts of the boltwork are to be connected to the lock unit (e.g..for activating a blocking
device), corresponding adapters can be fixed with screws (# 10 - 32 or M4) to the front of the
lock bolt (tightening torque for 15mm screwing depth: 200Ncm maximum).
•
•
•
10. The lock can be fitted to safes or vault doors of any material.
•
•
•
ScanLogic D22 – Biometric Safe Lock
The ScanLogic D22 is a very reliable and robust biometric safe lock
system ideal for commercial applications. The ScanLogic D22 features
SecuRam’s rugged stainless steel construction, optical fingerprint
authentication and 1,000 event audit reporting.
Simple to Use. Reliable.
Place your registered finger on the optical reader and turn the safe
handle. That’s it.
Easy fingerprint enrollment process; Open with fingerprint and/or code.
ScanLogic D22 supports 30 fingerprints and 30 codes plus a 1,000
event date and time stamped audit trail.
Every SecuRam lock undergoes a 2,000 cycle quality management
program before it leaves the manufacturing facility. Unprecedented
commitment to quality and reliability.
Features
Supports 30 fingerprints with our patented OneTouch fingerprint
verification – 6 digit codes
1,000 event date and time stamped audit trail
Programmable Time Delay 0-99 minutes; 0-15 minute Time Window
Time Delay Overide Codes – selectable
Duress Time Delay allows you to program the Time Delay value when
under duress operation
Recovery Code
Single or Dual Modes
Enable / Disable User Codes
Can Control up to 4 locks and authorize user access for each lock
Standard footprint and mounting pattern, easy retrofit for any
mechanical or electronic safe lock
SureLock Battery Management and AC power optional
Finishes available: Chrome, Brass, Black Chrome, Nickel
Can be paired with any other SecuRam motorized safe lock actuators.
Part#: FPC-0601A-D22
Select your Lock Body:
SwingBolt
SwingBolt w/Status
DeadBolt
SpringBolt
StrikeBolt
EL-0601
EL-0601-S
EL-0701
EL-0801
EL-0901
FPC-0601A-D22 Entrypad
EL-0601
SwingBolt Lock Body
Works with these
Lock Bodies also:
DeadBolt
SpringBolt
StrikeBolt
SecuRam® is the registered trademark
of SecuRam Systems Inc. USA
Security Expert Since 1991
10
11
WARRANTY CARD
NOTES
Date of purchase
Item Description
Company/WDs Name
Address & Stamp
Signature
:
:
:
:
:
Invoice No.
Model No.
Serial No.
:
:
:
M/s. Godrej & Boyce Mfg. Co. Ltd. through its Godrej Security Solutions Business (hereinafter
referred to as "the Company"), undertakes and gives warranty to the original purchaser as follows:
The Company warrants that if within a period of 12 (twelve) months from the date of purchase of
the
product bearing Sr.No. mentioned above, the same is found defective on account of any of its
parts proving to be defective in material or workmanship, the same shall be repaired or replaced
free of charge. The question, however, whether the product as a whole or any of its parts are
defective or inoperative due to faulty material or workmanship shall be within the sole discretion of
the Company. This is also subject to the further condition that the product is brought to the
Company's notified authorised service centre by the purchaser at his own risk, the expenses and
carriage paid both ways. In the event, the Company carries out repairs or replacement of any parts
during the said warranty period, the warranty shall thereafter continue only for the unexpired
period of the original warranty and the purchaser shall not be entitled to insist on the original
warranty being extended from the date of such repairs or replacement. The Company, however,
shall not be liable to carry out the repairs or replacement within any specified time. This warranty is
not valid for:
a) damage resulting from accident, mishandling, negligence, tampering, fire, acts of nature, loss of
components or accessories
b) replacement/repairs by people other than the authorised personnel
c) the consumable parts like batteries, plastic parts etc. and accessories.
This warranty shall not extend towards the payment of any compensation to anyone or entitle the
purchaser to a replacement of the product as a whole, and expressly excludes any claim for
consequential loss or damage.
This Warranty Card must be duly filled in, stamped and signed by the Dealer. This card and the
relevant cash memo must be preserved and be produced alongwith the defective units.
This warranty is valid only for purchases and installations effected from the Company/Company's
authorised outlets.
This warranty will apply if and only if the purchaser has taken due care in the use and maintenance
of the product as specified by the Company and has not mishandled it. It is made specifically clear,
that under no circumstances will the Company incur any liability for any damage caused due to the
gas leakage / fire / burglary / power fluctuations etc. if undetected either by malfunctioning or by
improper usage or lack of maintenance.
This warranty will not apply if the defect is not notified to the Company or its representative within 7
working days from the date the purchaser becomes aware of the defect in the product; if the
product is shifted from its original location of installation to a new location without prior written
intimation to the company or its authorised Service Centre.
Any claim made under this warranty shall be subject only to the jurisdiction of the courts in
Mumbai.
12
13
NOTES
NOTES
NOTES
NOTES