7000 Interior Latex Flat Paint
No. 447496 White
GENERAL DESCRIPTION
When cost is a leading factor, choose Valspar
7000. Quick and easy to apply, Valspar 7000
provides maximum value for interior
commercial projects.
PRODUCT FEATURES





Easy application by brush, spray or roll
Uniform appearance
Fast drying
Consistent hide and touch up
Low odor, low VOC for minimal disruption of
occupied spaces
APPLICATORS
PRODUCT
SPECIFICATIONS
Airless Spray:
Pressure: 2000 psi
Tip: 0.015-0.019”
Brush: Premium quality polyester
Roller: Premium quality roller 3/8” nap
CLEANUP
Clean up with warm, soapy water.
COMPOSITION
Fill (oz/gal)
RECOMMENDED USES






Drywall
Plaster
Acoustical tile
Masonry
Primed wood or metal
Previously painted surfaces
White/Base 1
Ready mix
124
128
SYSTEM
RECOMMENDATIONS
Drywall/Wallboard:
1 Coat: Valspar PVA Primer
1-2 Coats: 7000 Interior Latex Flat
SHIPPING AND
PACKAGING
Plaster:
Freight Classification:
Wood:
Paint or Paint Related Material.
Protect from freezing.
Packaging:
Gallon – 4 per carton
5-gallon pail
1Coat: Valspar Bonding Primer
1-2 Coats 7000 Interior Latex Flat
1 Coat: Valspar Bonding Primer
1-2 Coats: 7000 Interior Latex Flat
Block:
1 Coat: Block Filler
1-2 Coats: 7000 Interior Latex Flat
Concrete/Masonry:
1 Coat: Valspar Masonry and Stucco Primer or
Block Filler
1-2 Coats: 7000 Interior Latex Flat
Vehicle Type: Vinyl copolymer
Pigment Type: Titanium Dioxide
Recommended Film Thickness:
2.6 mil Wet
1.3 mil Dry
Viscosity: 97-107 Krebs Units
Gloss: 0-8 Units @ 60° angle
Sheen: 0-4 Units @ 85° angle
Flashpoint: 205 °F
VOC (g/L): Less than 50 g/L
VOC (lbs/gal): 0.33
Volume Solids: 28%
Weight Solids: 46%
Weight Per Gallon: 11.2 lbs/gal
Practical Coverage:
350 sq. ft./gal. (27.9-37.2 m2) depending on
surface porosity
Dry Time @ 77 °F and 50% Relative
Humidity
To The Touch: 1 hour
Recoat: 4 hours
Full Cure: 7 days
Application Temperature – Air: 50-90 °F
Application Temperature – Substrate:
50-90 °F
Storage Temperature: 40-90 °F
REGULATORY
COMPLIANCE
SCAQMD
CARB 2000 SCM
CARB 2007 SCM
OTC/LADCO
AIM
Yes
Yes
Yes
Yes
Yes
ENVIRONMENTAL
COMPLIANCE
LEED CANADA NC 1.0
GREEN SEAL
LEED NC 2.2
Yes
Yes
Yes
7000 Interior Latex Flat Paint
No. 447496 White
SURFACE PREPARATION
General:
Read the Lead Warning in Cautions section.
Clean the surface thoroughly to remove surface
contamination, mildew, stains, and rust with an
appropriate cleaner. Scrape off any loose or
peeling paint. Spot prime when needed. Dull
glossy surfaces with light sanding.
Drywall:
Fill cracks, pits and voids with patching
compound or spackle, let dry and sand smooth.
Joint compounds must be cured and sanded
smooth. Remove all sanding dust.
Plaster:
Allow new plaster to fully cured and hard.
Surface should be free of dust.
Wood:
Sand wood smooth and patch holes and
imperfections with wood filler or putty and sand
smooth. Remove all sanding dust.
Block:
Masonry surfaces and mortar should be fully
cured, usually about 30 days. Remove any
loose material or dust.
Concrete/Masonry:
New surfaces should be cured, usually 30
days. Remove all form release or curing
agents. Surfaces should be free of loose
materials and dust.
Mildew Removal:
Remove mildew or suspected mildew by
scrubbing with a commercial mildew remover or
a solution of 1 part chlorine bleach to 3 parts
water. Allow solution to remove on surface for
10 minutes. Rinse thoroughly with water and
allow surface to dry completely. Take
precautions to avoid contact with skin or eyes.
APPLICATION
Stir thoroughly and intermix multiple containers
of the same color. Apply products at
temperatures ranging from 50-90 °F. Apply by
brush, roller or spray application. Thinning is
not recommended.
LEAD WARNING
WARNING! If you scrape, sand or remove old
paint, you may release lead dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN
CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-approved
respirator to control lead exposure. Clean-up
carefully with a HEPA vacuum and a wet mop.
Before you start, find out how to protect
yourself and your family by contacting the
National Lead Information Hotline at 1-800-424LEAD or log on to www.epa.gov/lead.
LIMITED WARRANTY
This product is warranted to meet the
application, appearance and performance
properties stated on the label. This warranty
covers product that is applied to a properly
prepared surface in accordance with label
directions and excludes failure due to
deterioration of the underlying surface,
structural defects or failure of previous paint. If
the product fails to perform as warranted, return
any unused portion to the store with proof-ofpurchase and you will receive, as your sole
remedy under this warranty, your choice of
additional product of equal value or a full
refund. THIS WARRANTY EXCLUDES LABOR
OR THE COST OF LABOR FOR THE
APPLICATION OF ANY PRODUCT AND
EXCLUDES ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states
do not allow the exclusion or limitation of
incidental or consequential damages, so the
above limitation or exclusion may not apply to
you. This warranty gives you specific rights,
and you may also have other rights that vary
from state to state.
CAUTIONS
WARNING! Contains Crystalline Silica. KEEP
OUT OF THE REACH OF CHILDREN. May
cause eye and skin irritation. USE ONLY WITH
ADEQUATE VENTILATION. Avoid breathing
vapors, spray mist or sanding dust. If painting
indoors, open windows and doors or use other
means to ensure fresh air entry during
application and drying. If you experience eye
watering, headache or dizziness, or if air
monitoring demonstrates vapor/mist levels are
above applicable limits, wear an appropriate,
properly fitted respirator (NIOSH approved)
during and after application. Follow respirator
manufacturer’s directions for respirator use.
When sanding, wear a dust mask. AVOID
CONTACT WITH THE EYES AND SKIN. Wash
thoroughly after use. Close container after each
use. DO NOT TAKE INTERNALLY. Delayed
effect from long-term exposure: Cancer
Hazard. Contains crystalline silica, which can
cause cancer. Risk depends upon duration and
level of exposure to dust generated from
sanding surfaces or spray mist. WARNING:
This product contains a chemical known to the
State of California to cause cancer. FIRST AID:
EYE CONTACT: Flush thoroughly with water
for at least 15 minutes. If irritation persists, get
medical attention.* IF INHALED: If affected by
vapor or spray mist, move to fresh air. If
breathing difficulty continues, get medical
attention.* IF SWALLOWED: Drink 2 glasses of
water. Get medical attention immediately.*
*Call poison control center, hospital emergency
room or physician immediately.
CL 3.3
DO NOT TAKE INTERNALLY.
KEEP OUT OF REACH OF CHILDREN.
For additional safety and chronic health
hazard information, refer to the Material
Safety Data Sheet for this product.
EMERGENCY MEDICAL TELEPHONE:
1-888-345-5732
This product contains less than 50 g/L VOC
1191 Wheeling Road, Wheeling, IL 60090
888.313.5569
www.valsparpaint.com
Revised: January 2013