Material Safety Data Sheet
4CPDS-72
4 = EXTREME
FLAMMABLE
HEALTH
REACTIVE
SPECIAL
HAZARD
2 = MODERATE
Phone Number
(For Information)
Emergency Contact
Phone Number
Polyglass U.S.A., Inc
1111 West Newport Center Dr
Deerfield Beach, FL 33442
Identity
Date Prepared
Prepared By*
954-233-1330
CHEMTREC (USA)
800-424-9300
1
0
1 = SLIGHT
0 = INSIGNIFICANT
Polybrite 72 White Flashing Compound
Manufacturer
Address
0
3 = HIGH
Page 1 of 2
Polybrite 72 White
Flashing Compound
05/15/08
R&D
SECTION 1 - MATERIAL IDENTIFICATION AND INFORMATION
COMPONENTS – CHEMICAL NAME & COMMON
NAMES (HAZARDOUS COMPONENTS 1% OR GREATER;
CARCINOGENS 0.1% OR GREATER)
Acrylic polymer(s)not hazardous – CAS # Proprietary
Calcium Carbonate
1317-65-3 7 - 13
Silica, Quartz
14808-60-7 0.1 - 1
Titanium Dioxide
13463-67-7 5 - 10
Zinc Oxide (as zinc)
1314-13-2 3 - 7
Aqua ammonia
CAS # 1336-21-6
Inert Ingredients
%*
54.0-60.0
7-13
0.1-1
5-10
3-7
≤0.10
<Balance>
OSHA
PEL
ACGIH
OTHER LIMITS
RECOMMENDED
N/A
N/A
N/A
N/A
N/A
35mg/m3
N/A
N/A
N/A
N/A
N/A
17mg/m3
N/A
N/A
N/A
N/A
N/A
N/A
SECTION 2 - PHYSICAL/CHEMICAL CHARACTERISTICS
Boiling Point
Vapor Pressure (mm Hg.)
Vapor Density (Air=1)
Solubility in Water
Appearance and Odor
212°F
760@212°F
>1
Dispersible
Creamy White Liquid
paint like odor
Weight per gallon
Melting Point
Evaporation Rate
10.0-11.5 lbs
N/A Liquid
<1
SECTION 3 - FIRE AND EXPLOSION HAZARD DATA
Flash Point (Method Used): SETA >212°F
Air % by Volume: N/A
Auto-Ignition: N/A
LEL: Not Available
Temperature: N/A
UEL: Not Available
EXTINGUISHING MEDIA
Chemical Foam, CO2, Dry Chemical, Water Fog
UNUSUAL FIRE AND EXPLOSION HAZARDS
Keep containers cool with water spray to prevent container rupture due to steam buildup; floor will become slippery if material is released. Firefighters should
wear self-contained breathing apparatus and full protective gear. Product is not considered flammable or combustible. Products of combustion include
compounds of carbon, hydrogen, oxygen, aluminium and zinc, including carbon monoxide.
SECTION 4 - REACTIVITY DATA
STABILITY: Stable
Incompatibility (Materials to Avoid): Strong oxidizers, strong acids
Hazardous Decomposition Products: Decomposition will not occur if handled and stored properly. In case of a fire, oxides of carbon, hydrocarbons, aluminum
and zinc fumes and smoke may be produced.
HAZARDOUS POLYMERIZATION: Will Not Occur
CONDITIONS TO AVOID (STABILITY): Extreme temperatures.
SECTION 5 - HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY:
CARCINOGEN LISTED IN:
X Inhalation X Skin Absorption X Eyes X Ingestion Not Hax ___ NTP ___ IARC Monograph ___ OSHA ___ Not Listed
HEALTH HAZARDSHEALTH HAZARDS
Acute and Chronic and Signs and Symptoms of Exposure: Over exposure to vapors causes eye irritation, blurred vision, dizzyness, headaches, even
unconsciousness. Prolonged or repeated skin contact can cause moderate irritation, defatting, dermatitis. Swallowing can cause gastrointestinal irritation, nausea,
vomiting, and diarrhea. Aspiration of material into lungs can cause chemical pneumonitis which can be fatal.
EYE CONTACT
May cause eye irritation.(burning, tearing, redness or swelling. Flush with large amounts of water, lifting upper and lower lids occasionally. Get medical attention.
SKIN CONTACT
None expected, however prolonged contact may cause irritation. In case of contact remove contaminated clothing and shoes. Wash affected areas with soap and water.
INHALATION
None expected, however some individuals may experience minor nausea or headaches. Remove the person from the contaminated area to fresh air. If breathing
is difficult, give oxygen. Contact a phusician if symptoms develop.
INGESTION
Get medical attention immediately. Do not induce vomiting.May cause liver and kidney damage. May cause central nervous system depression,, characterized by
excitement, followed by headache, dizzines, drowsiness or headache.
Polybrite 72 White Flashing Compound
Page 2 of 2
Material Safety Data Sheet
4CPDS-72
SECTION 6 - CONTROL AND PROTECTIVE MEASURES
RESPIRATORY PROTECTION (SPECIFY TYPE): Use hydrocarbon vapor canister or supplied-air respiratory protection in confined or enclosed spaces if
needed.
PROTECTIVE GLOVES: Use chemical resistant gloves if needed to avoid repeated or prolonged skin contact
EYE PROTECTION: Use splash goggles or face shield when eye contact may occur.
VENTILATION TO BE USED: Use with adequate general and local exhaust ventilation. When used outdoors, stay well away from builing air intakes or close
and seal the intakes to prevent product from entering building.
OTHER PROTECTIVE CLOTHING AND EQUIPMENT: Use chemical resistant apron or other clothing to avoid repeated or prolonged skin contact.
SECTION 7 - PRECAUTIONS FOR SAFE HANDLING AND USE/LEAK PROCEDURES
STEPS TO BE TAKEN IF MATERIAL IS SPILLED OR RELEASED
Recover free liquid. Add absorbent (sand, earth, sawdust, etc.) to spill area.
WASTE DISPOSAL METHODS
Collect and dispose in accordance with applicable regulations.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE
Keep containers closed when not in use. Store in a cool, dry, well-ventilated area. Protect from physical damage. Protect from extreme temperatures. Keep out of
the reach of children
SECTION 8 - TRANSPORTATION DATA
DOT: Not regulated for transport
IMO/IMDG: Not regulated (Not dangerous for transport)
Transportation classification may vary by container volume and may be influenced by regional or country variation in
regulations
SECTION 9 - REGULATORY INFORMATION
WORKPLACE CLASSIFICATION:
This product is considered non-hazardous under the OSHA Hazard Communication Standard (29CFR1910.1200)
This product is not a ‘controlled product’ under the Canadian Workplace Hazardous Materials Information System (WHMIS)
SARA TITLE III Section 311/312 (40CFR370): N/A
SARA TITLE III Section 313 (40CFR372): There are no SARA 313 ingredients in this material in excess of de minimis amounts.
CERCLA (40CFR302.4): Release of this material to air, land, or water is not reportable to the National Response Center under the CERCLA regulation and
Section 304 of SARA Title III. However, local and state regulations may be more restrictive thus it is advisable to check with the local and state regulatory
agencies for spills/releases reporting requirements.
TSCA: All components of this product are in compliance with the inventory listing requirements of the US Toxic Substance Control Act (TSCA) Chemical
Inventory.
Pennsylvania: Any material listed as “Not Hazardous” in the CAS REG No. of Section 1, Composition/Information On ingredients, of this MSDS is a trade secret
under the provisions of the Pennsylvania Worker and Community Right-To-Know Act.
POLYGLASS U.S.A., Inc.: Corporate Office Deerfield Beach, Florida 33442- Phone (954)233-1330
Fax (954) 418-4453 - Manufacturing Facilities Hazleton, Pennsylvania 18202 - Phone (570) 384-1230
Fax (570) 384-3282 Toll Free (800) 894-4563 • Winter Haven, Florida 33880 - Phone: 863-297-5800
Fax: 863-297-5858 - Toll Free: 866-802-8017 • Fernley, Nevada 89408 Phone (775) 575-6007
Fax (775) 575-2314 - Toll Free (800) 222-9782 www.polyglass.com - e-mail:[email protected]