W W W . V U LY T R A M P O L I N E S . C O M BASKETBALL HOOP ASSEMBLY | Maintenance Manual 8 Ft. | 10 Ft. | 12 Ft. | 14 Ft. | Vuly Trampolines READ THIS ENTIRE MANUAL BEFORE ASSEMBLING AND USING VULY PRODUCTS. THESE PRODUCTS ARE FOR PERSONAL USE ONLY BY PERSONS AGED 6 YEARS AND OLDER NOT RECOMMENDED FOR CHILDREN UNDER 6 YEARS OF AGE | USE OFFICIAL VULY BASKETBALL ONLY PLEASE DO NOT HANG FROM OR JUMP INTO BASKETBALL HOOP, ONLY TO BE USED WITH EXTREME CAUTION! BASKETBALL HOOP | Assembly Instructions STEP 01 Unpack the components from your basketball hoop box. Your box should contain: BASKETBALL HOOP PARTS LIST 1x Pre-assembled Hoop and Backboard with frame 1x Basketball 1x Basketball pump with needle (in handle) 1x Upper support pole 1x Lower support pole (with rectangular bracket) 2x Net pole elastics (slightly longer) 4x Bolts 4x Nuts 4x Round ended nuts 1x Spanner 1x Screwdriver 3x Long foams 2x Short foams (8ft and 10ft only requires 1x) PAGE 2 STEP 02 Push in net pole spring button to remove a net pole from your trampoline. STEP STEP 04 Lift up the safety pads where you removed the safety net pole from. Push the lower support pole through the safety pads hole. STEP 05 Insert the lower net pole into the lower support pole. Note: Rotate until the holes match. 03 Remove the elastic ties, covers, and foams from the net pole using the spanner. Separate the upper net pole and the lower net pole. PAGE 3 STEP 06 Using the screwdriver, insert the screw back into the net pole through the rectangular bracket and t-join to hold the lower net pole in position. Put each bolt through the square holes in the bracket from the outside so the bolt heads face towards you. Make sure the bolts go through both sides of the bracket before attaching the nuts onto the end of each bolt. Tighten the nuts evenly to avoid bending the bracket. If you tighten each bolt all the way before tightening the others, you may bend the bracket. Note: The round holes on the rectangular bracket that house the net pole screw and spring button must be facing outwards. STEP 07 Add a long foam and cover over the lower support pole. PAGE 4 For 12, 14ft ONLY Also add a short foam piece before attaching the elastic tie. STEP 08 Insert the slightly longer elastic tie in the hole above the foam, ensuring elastic loop is facing inwards, towards the net. STEP 09 Join the upper support pole to the lower support pole. Note: Rotate until the holes match. STEP 10 Attach the upper net pole. Insert your existing top foam and cover from your net pole into the completed net pole. STEP 12 Add a short foam and a cover. STEP 13 Add a long foam and a cover. STEP 11 Insert the elastic tie in the top hole. PAGE 5 STEP 14 With the backboard face down, lift up the frame until it clicks into position. STEP 15 Remove the black plastic cap at the top of the safety net pole. Insert the basktball hoop on top of the net pole. Put the elastic tie bolt through the net pole and the basketball hoop pole. Using the spanner, tighten the nut onto the elastic tie bolt and then re-attach the net to your elastic ties. PAGE 6 Congratulations! You have finished assembling your Vuly Basketball Hoop. W W W . V U LY T R A M P O L I N E S . C O M Australia | 1300 - 667- 514 USA | 1 - 877- 538 - 8018 VULY TRAMPOLINES |ÛÛ@f_d]klgfÛIgY\ÛÝÛNYc]jd]qÛHC;Û~Û8mkljYdaY kYd]k³nmdqljYehgdaf]k[geÛÝÛooonmdqljYehgdaf]k[ge
© Copyright 2024 Paperzz