4
1500
c
c
c
5
6
3000
3
2850
2
150
0
1
8
NOTES :
1. THE FOLLOWING INFORMATION IS OBTAINED FROM THE CONSTRUCTION SCHEDULE :
c
a. POLE LENGTH AND STRENGTH.
23
0
7
b. SPECIAL FOUNDATION REQUIREMENTS.
c. POLE EMBEDMENT DEPTH.
c
A
A
d. PHASE CONDUCTOR AND OVERHEAD EARTH WIRE SIZE.
230
e. VARIATIONS TO STANDARD CROSSARM REQUIREMENTS.
c
2700
2550
1350
750
150
c
9 10 11
h. ASSESSED EARTHING REQUIREMENTS.
13
2. ALL BOLTS AND INSULATOR PINS PASSING THROUGH TIMBER ARE TO BE COATED
12
c
WITH GRAPHITE GREASE.
3. THE MAXIMUM LINE DEVIATION ANGLE TO BE CONSTRUCTED ON THIS ARRANGEMENT
c
0
f. STAY REQUIREMENTS.
g. DEVIATION ANGLE.
IS TO BE DETERMINED BY THE LINE DESIGNER.
c
c
c
4. THE LOAD AND DEVIATION ALLOWABLE ON THE EYEBOLT AND EYENUT ASSEMBLY
c
980
IS TO BE DETERMINED FROM DRG : 520331.
5. LONGROD INSULATORS TO BE USED UNDER ALL CONDITIONS.
16 17 18
B
B
6. POLES SHALL BE DRILLED, SCARFED AND DRESSED ON SITE. DRILLING AND SCARFING
5
TO BE TREATED WITH APPROVED PRESERVATIVES.
7. WHEN DESIGNING UNDERBUILT CIRCUITS ON A 33kV STRUCTURE, THE POSSIBLE USE OF
LIVE LINE WORKING PROCEDURES MUST BE CONSIDERED WHEN NOMINATING THE CIRCUIT
SEPARATION TO ALLOW A MINIMUM CLEARANCE OF 2500mm IF REQUIRED.
c
1730
15 14
4
6 7 8
22 21 20 19
CONSTRUCTION - THROUGH TERMINATION, 33kV, 4-11
513930
22
WASHER - SPRING, M12, STAINLESS STEEL
518082
6
21
WASHER - FLAT, M12, STAINLESS STEEL
518081
12
20
BOLT & NUT - M12x25mm, HEX., STAINLESS STEEL
515467
6
19
LUG - COMPRESSION (TO SUIT CONDUCTOR)
514053
6
18
WASHER - CONICAL, M16, STAINLESS STEEL
518082
6
17
WASHER - FLAT, M16, GALVANISED
518081
6
16
BOLT & NUT - M16x150mm, HEX., GALVANISED
515466
6
c
C
3
c
2730
1
FUSE - LINK, 33kV, 20AMP, CURRENT LIMITING DROPOUT, OUTDOOR USE (S/C H24466)
3
FUSE - LINK, 33kV, 10AMP, CURRENT LIMITING DROPOUT, OUTDOOR USE (S/C H24432)
3
14
BASE - DROPOUT FUSE, 33kV, INCLUDING FUSE END FITTINGS (S/C 24490)
3
13
BRACKET - DROPOUT FUSE, 30
12
BLOCK - GAIN, ALUMINIUM, 100mm (S/C 146274)
11
WASHER - CONICAL, M20, STAINLESS STEEL
518082
2
10
WASHER - SQUARE, 75x75x6mm, GALVANISED (22mm HOLE)
518081
4
9
BOLT & NUT - M20, GALVANISED (LENGTH TO SUIT POLE)
515466
2
8
WASHER - CONICAL, M12, STAINLESS STEEL
518082
1
7
WASHER - FLAT, M12, GALVANISED
518081
1
6
BOLT & NUT - M12x150mm, HEX., GALVANISED
515466
1
5
CROSSARM - 2700x100x100mm, TYPE I, HARDWOOD OR LAMINATED VENEER
514375
2
4
SCREW - COACH, M12x100mm, GALVANISED (S/C H40484)
3
BRACE - CROSSARM, ANGLE, 920x50x50x5mm, GALVANISED
514381
1
2
CONSTRUCTION - HORIZONTAL PIN, 33kV, 4-1
513923
1
1
POLE - TIMBER (AS REQUIRED) (12.5m MINIMUM)
513988
1
15
2
D
E
20110909
1
2
ITEM
DO NOT SCALE.
NETWORK STANDARD
DESIGNED
DRAWN
APP’
D by: GLENN FORD
AUSGRI
D BORDER APPLI
ED.
10/
2013
DATE: 21/
6
G
CHKED:GARRY CRAI
DWN:GARY HUGHES
APP’
D by: GLENN FORD
SECOND BRACE ADDED TO
BOTTOM CROSSARM.
12/
2010
DATE: 22/
5
LLI
P JONES
CHKED:PHI
CI
A RI
OS
DWN:PATRI
A M E N D M E N TS
CAD DRAWI
NG
F
DO NOTMANUALLY AMEND
ALL DIMENSIONS IN MILLIMETRES UNLESS NOTED OTHERWISE.
-
AUTHORISED
DATE
145 NEWCASTLE ROAD
WALLSEND NSW 2287
P.A.S
R.BREMMELL
1:25
MAP REF.
LGA
PHONE: 02 4951 9388
FAX: 02 4951 9389
PROJECT No.
PROJTRAK No.
4
5
SIZE
STD
2
A3
-
6
DRAWING No
513957
7
C
3
D
1
E
DRG. No QTY
STANDARD CONSTRUCTION
33kV THROUGH TERMINATION
WITH GREATER THAN 4kA
DROPOUT FUSES
4-60
16/04/96
SCALE
517465
DESCRIPTION
PETER SAUNDERS
CHECKED
3
1
23
F
SHEETS
AMD.
01 of 1
6
8
C