Waterbase Epoxy
2-COMPONENT, 4 T0 1 MIX RATIO
PRODUCT DATA
PRODUCT DESCRIPTION
Volumetric Ratio. 4 to 1
Solids
50% (+ or - 1%)
Coverage 200 SF/gal. undiluted 300-400 SF/gal. mixed
with 64 oz. water to every pre-blended gallon of epoxy.
A premium quality 2-component waterbased epoxy concrete
sealer/primer that provides epoxy toughness, chemical resistance and durability with the convenience of a water base VOC
free system.
APPLICATIONS
TOP COAT OR BROADCAST:
Apply at 200 sf/gal undiluted
Primer coat cut up to 50% with water
and apply at 300-400 sf/gal
The uniqueness and universality of Epoxy Plus's epoxy chemistry facilitates the applications where USDA Food & Beverage
and other regulatory requirements must be obtained. i.e. food
manufacturing and preparation, pharmaceutical manufacturing
and dispensaries, clean rooms, commercial kitchens, laboratories and more. Other areas of use include: garage floors, rest
rooms, manufacturing facilities, automotive showrooms and
schools etc.
Color Pigments:
WB Epoxy is available with standard
premixed colors or in clear base with
pourable pigment color kits.
Stock Pigments Include:
• Beige
• Clear
• Tile Red
• Light Gray
• Safety Red
• Medium Gray
• Safety Blue
• Dark Gray
• Safety Green
• White
• Safety Yellow
• Black
• Tan
ADVANTAGES
• Easy water clean-up
• Long pot life (3 hours)
• Excellent coverage-hide
• Fast drying (30 mins – 2 hrs)
• Unsurpassed Adhesion
• VOC Free
Finish:
Gloss
INSPECTION
Packaging
Surface must be structurally sound, dry, and free of oil, grease,
curing agents, dirt, dust or other foreign matter. Surface must
be roughed up or porous. This product is designed for use over
untreated concrete surfaces free from wax, dusting preventive
sealers, deep penetrating sealers, bond breaking compounds
and release agents and other similar chemicals that will interfere with proper adhesion and lead to premature coating failures.
1.25 Gallon Kit:
Part A . . . . . . . . . . . . . . . . . . . . . . 1gal (128 oz)
Part B . . . . . . . . . . . . . . . . . . . . . . Quart.(32 oz)
5 Gallon Kit:
Part A . . . . . . . . . . . . . . . . . . . . . . 4gal (512 oz)
Part B . . . . . . . . . . . . . . . . . . . . . . 1gal (128 oz)
PHYSICAL PROPERTIES
Property
Value
Compressive Strength
Flexural Strength
Tensile Strength
Bond to Concrete
7,800 psi
3,700 psi
3,900 psi
350 psi
Taber Abrasion
Flammability
Hardness, Shore D
Flash Point
75-80 Mgs
Self-extinguishing
84
>200°F
Reference
ASTM C 695
ASTM D 790
ASTM D 638
ASTM D 4541
Concrete fails at this point
ASTM D 4060
ASTM D 2240
TECHNICAL DATA SHEET
123 Town Square Place Suite 115 Jersey City, NJ 07310
(551) 208-2895 WWW.EPOXYPLUS.COM
SURFACE PREPARATION
COVERAGE
Prepare surface by sanding, grinding, dry or wet sandblasting or
shot blasting to achieve a clean, porous and uniform ex posed
aggregate finish with a CSP (Concrete Surface Profile) rating of
"2" that will allow the product to penetrate the surface. Bead or
shotblasting is the most reliable method of preparation. Clearn
surface entirely with TSP and rinse completely with water
several times.
Three (3) mil dry film at 250 sq. ft. per gallon. Six (6) mil dry film
at 125 sq.ft. per gallon.
MILDEW
DO NOT PAINT OVER MILDEW. Mildew is a fungus, brown, black,
gray or even white in color, and will rapidly grow through any
coating applied over it. A solution of 50% household bleach and
50% water will kill the mildew. See precautions on bleach label
for handling before using.
MIXING
MIX 4 PARTS "A" WITH 1 PART "B" IN BATCHES NO LARGER THAN
1.25 GALLON AT A TIME EXCEPT AS NOTED ABOVE UNDER
“SELF PRIMING REQUIREMENTS”. Top Coat: In a clean and dry
bucket, mix 4 parts A and 1 part B together using an agitator,
jiffy mixer or stir stick. Mix slowly for at least 2 minutes or until
completely combined. Prepare only the amount you can use in 2
hours in quantities of no more than 1 gallon at a time. Do not
leave the mixed epoxy in the bucket longer than 4 hours.
THINNING
When using this product as a Primer, thin slightly with water if
necessary. To thin add up to maximum ½ gallon of water to a
preblended 1 gallon of Part A and Part B mixture and blend
slowly and thoroughly.
DRYING TIME/CURE TIMES
Under normal Conditions (70ºF & 50% Humidity) dries to touch
in 30 minutes to 2 hours depending on formulation. May be
recoated when dry to the touch. Do not apply to surfaces when
ambient or surface temperatures are below 50ºF. Higher temperatures and lower humidity will accelerate cure times and
reduce working time.
APPLICATION IN EXTREMELY HOT WEATHER
1. Dampen the floor surface to be coated. (Do not saturate)
2. In a large bucket, mix and prepare no more than a 1 gallon kit
at time.
3. Pour entire mixture evenly onto the horizontal surface to be
coated.
CLEAN UP
Soap and water. (Before curing begins)
APPLICATION INSTRUCTIONS
Immediatley prior to appplication, damper surface with a water sprayer. Do not puddle or leave standing water, spray only enough to
darken concrete surface. After, begin applying the properly mixed epoxy always making sure to keep a damp edge ahead of the application until the floor is complete.. For best results on horizontal surfaces, pour the entire mixture evenly onto the surface as soon as
possible after mixing. Use a 3/8" nap roller or squeegee to spread mixture over the surface, backrolling the area to be coated. For
best results apply at least 2 coats at 250 sq. ft. per gallon. Clean tools with soap and water before curing begins. To increase skid
resistance, stir in an approved non-skid additive into your A & B mixture.
CONCRETE SURFACE PREPARATION
Concrete surfaces should be clean, dry, and free of disintegrating chalky material or previously applied coatings to insure satisfactory
results. For proper adhesion surface must be mechanically ground or shotblasted to a uniform exposed aggregate finish with a CSP
(Concrete Surface Profile) rating of 2. The surface profile should resemble 80 grit sandpaper to be suitable for coating.
TECHNICAL DATA SHEET
123 Town Square Place Suite 115 Jersey City, NJ 07310
(551) 208-2895 WWW.EPOXYPLUS.COM
WARNING! SLIP AND FALL PRECAUTIONS
OSHA and the American Disabilities Act (ADA) have now set enforceable standards for slipresistance on pedestrian surfaces. The
current coefficient of friction required by ADA is .6 on level surfaces and .8 on ramps.
Epoxy PlusFlooring recommends the use of angular slipresistant aggregate in all cflooaotrininggs soyrstems that may be exposed
to wet, oily or greasy conditions. It is the contractor and end users’ responsibility to provide a flooring system that meets current
safety standards. Epoxy Plus or its sales agents will not be responsible for injury incurred in a slip and fall accident.
Handling Precautions
Use only with adequate ventilation. Appropriate cartridge-type respirator must be used during application in confined areas. Avoid
contact with skin. Some individuals may be allergic to epoxy resin. Protective gloves and clothing are recommended.
WARRANTY
Epoxy Plus products are warranted for one year after date of purchase. Please refer to the Limited Material warranty for additional
clarification.
KEEP OUT OF REACH OF CHILDREN
NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY
We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us
is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is
supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose.
Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical
and should not be construed as specifications.
NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED,
OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL
BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE
USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or
consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our
product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or
not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any
representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY.
BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.
Epoxy Plus LLC Revised April 2015