HAWTHORNE VANITY WITH MIRROR 32”H x 44”W SKU # 0895700130 – DARK CHERRY SKU # 0895700560 – OAK SKU # 0895700410 – WHITE SKU # 0895700210 – BLACK 45 Min. BEFORE BEGINNING ASSEMBLY, CHECK TO MAKE SURE ALL PARTS AND HARDWARE ARE ACCOUNTED FOR. IT IS SUGGESTED THAT YOU SAVE THE CARTON AND PACKING MATERIAL UNTIL AFTER ASSEMBLY IS COMPLETED. SELECT A CLEAN, SMOOTH SURFACE TO WORK (SUCH AS CARPET). THEN, FOLLOW THE EASY STEPS BELOW. IF PARTS ARE MISSING, PLEASE CALL 1-800-998-7021 FOR INFORMATION. MADE IN BRAZIL 16 02 04 12 3 1 5 2 8 6 11 10 6 7 6 9 6 4 12 17 15 16 14 13 PART # QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1 1 1 1 1 4 1 1 1 1 1 1 2 2 2 2 2 A B C D E F DESCRIPTION HINGED CENTER TOP RIGHT TOP LEFT TOP RIGHT SIDE LEFT SIDE UPPER FRONT SUPPORT RIGHT DIVIDER LEFT DIVISION CENTER FRONT CENTER BOTTOM BACK PANEL LOWER CROSS SUPPORT DRAWER FRONT RIGHT DRAWER SIDE LEFT DRAWER SIDE DRAWER BOTTOM DRAWER BACK 8x30mm (1 1/4") 4,0x30mm (1 1/4") 4,0x35 (1 3/8") 4,0x25 (1') 3,5x30 (1 1/4") 3,0x12 (1/2") 48 G SIZES (w x d x h) 183/4” x 20” x 3/4” 121/2” x 20” x 3/4” 121/2” x 20” x 3/4” 311/4” x 173/4” x 11/4” 311/4” x 173/4” x 11/4” 91/2” x 21/2” x 3/4” 161/2” x 7” x 3/4” 161/2” x 7” x 3/4” 19” x 5” x 3/4” 193/8” x 161/3” x 1/4” 391/4” x 7” x 3/4” 391/4” x 21/2” x 3/4” 91/4” x 51/3” x 3/4” 121/4” x 43/4” x 1/2” 121/4” x 43/4” x 1/2” 121/3” x 81/2” x 1/8” 8” x 43/4” x 1/2” Kit 60N 2 22 14 H 4 4 I 4 12 J 2 2 Insert wooden dowels (A) into the predrilled holes in parts 4, 5 6, 7, 8, 9, 11, 12, 14 and 15 as shown in the diagram. Insert and screw the metal guide supports (H) into right divider(7) and left divider(8). STEP 1 A A A 4 A 5 H H 8 A A H AA H 15 2x AA AA H A A 7 AA A A 14 2x 6 4x AA AA 9 AA A A 11 12 A A A A STEP 2 STEP Insert center front (9) into right (7) and left (8) sides and screw together using screws (C). 3 Insert vanity center bottom (10) by sliding panel into pre-routed grooves as shown in the diagram. Attach back (11) to center compartment using the dowels as your guide. Secure with screws (C) as shown in diagram. C C C 7 10 9 C C 8 11 C C C C C STEP 4 With center compartment laying on its back (11) as shown in diagram, attach the front cross supports (6), back panel (11) and bottom cross support(12) so that the sides(4 & 5) and center compartment are aligned and attached to one another with the dowels. Secure the front cross supports (6) using the pocket screws (B). B 6 6 B B 5 B 6 6 B 12 - + 4 STEP 5 Lay the three tops ( 1, 2 & 3 ) as shown in diagram upside down on soft surface. Turn base over to align holes on the vanity and tops with the dowels and secure together using pocket screws (B and C) as shown in diagram. Assure alignment is made with the metal pine and secure with screws (D) as shown. D C C B B C C B C B C D B C 3 C 1 2 STEP 6 This construction is for 2 drawers: Screw drawer sides (14 & 15) to drawer front (13) using pocket screws (B). Slide drawer bottom (16) into pre-routed groove to the bottom of the drawer assembly. Attach drawer back (17) to the drawer assembly using screws (E). Attach drawer catch (J) using screw (F). Attach drawer knob ( I ) to front of drawers using screw (E). 2x E E 14 B B 16 B 15 B 17 E E B F 13 J F E I J STEP 7 Once vanity has been turned right side up and drawers have been inserted it is time to attach the hinges (G). Attach the hinge to that it is positioned to the left hand side of the vanity as shown with hinge folding up. Using screws (G) attached the hinge using the predrilled holes on the vanity top and center. Attach the knobs (I) to the center section of the vanity using screws (E). Kit 60N G G G Kit 60N G G 90º G G E E I I STEP8 Tipping restraint Instructions TIPPING RESTRAINT HARDWARE A 1 Nylon strap B 2 1 ½” screw C 2 6mm Plastic screw anchor D 2 Plastic wall bracket E • When properly installed, this hardware can provide protection against the unexpected tipping of furniture. • Attach one of the mounting brackets “D” securely to the back top edge of the unit using the short screw “E”. • Mark the location on the wall for mounting the second bracket "D". Drill the appropriate sized hole in the wall and insert the plastic screw anchor "C". Then secure the bracket to the wall using screw "B". • Place the unit so the bracket on the back edge of unit is in line with the bracket on the wall. 2 Small screw Set in furniture E E D Set in Wall B B C • Lace the end of the nylon restraint strap “A” through each bracket. Bring both ends together and slide the beaded end of the strap through the keyhole shaped slot on the other end. Pull down on the beaded end until it snap-locks into the keyhole. • Check to make sure the strap is securely laced and locked to the brackets. WALLBOARD A C WALLBOARD D
© Copyright 2026 Paperzz