Manufacturers of
In-Floor Access Enclosures
Patent 5.412.911
Time Saving Installations, Convenience, Standardization
For Gaining Access To Under Floor Mechanicals !
Manufactured In-Floor access enclosures and pit
systems for providing access to under-floor:
• Mechanicals
• Water piping and valves
• Drainage hubs and piping
• Electrical wiring and controls
• Refrigeration piping and controls
In-Floor Access for Grocery, Retail, Manufacturing,
Industrial and Institutional
Available for use with our composite liners or your
on-site constructed pit.
We can configure a unit to any size and cover
requirements.
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
700 Henry Circle, Sinking Spring, PA 19608
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: craiggmfg @craigg.com
www.CRAIGG.com
12
ǻEĶsŸ¯NŸŘǼsŘǼǣ
SECTION 1
The ADJUSTOR
Construction Detail
SECTION 2
Installation Detail
The POUROVER
Construction Detail
SECTION 3
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
ADJUSTOR FRAME
Construction Detail
SECTION 4
Installation Detail
RIGIDCAST
SECTION 5
Construction Detail
Installation Detail
RIGIDCAST TRU SCREED
Construction Detail
SECTION 6
Installation Detail
POUROVER FRAME
Construction Detail
SECTION 7
Installation Detail
Bordered Covers
Borderless Covers
Flush Covers
Two Piece Cover
Partial Covers
Cover Supports
SECTION 8
Two Part Frame Assembly
Combination Adjustor and Pourover Frame & Liner
Angled Adjustor and Pourover Frame & Liner
Double End Adjustor with Pourover Center Frame & Liner
Combination Adjustor ,Pourover and Open Area Frame & Liner
Flush Mounting Unit Frame & Liner
Fixed Cover with Frame & Liner
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
700 Henry Circle, Sinking Spring, PA 19608
12
SECTION 9
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 1-1
ǢƻrNÝ®ÝNǻÝŷŗǢ
ASTM
UPPER: Extruded Aluminum 6105-T5
B221
LOWER: 7 Gauge (0.1793”) thick, Low Carbon Steel
A36
GASKET: Shore Type A Cork-Rubber w/ Acrylic PSA
D2240
STUD: 7/16-14 TPI x 4” Lg., Low Carbon Steel w/ Yellow Zinc Grade 2
A307
BORDER FRAME: Extruded Aluminum 6105-T5
B 221
PLATE: 0.25” or 0.375” thick, Aluminum Plate 6061, Temper T651, Mill Finish
B209
ALUMINUM TREAD PLATE: 0.25” or 0.375” thick, 6061, Temper T651
B632
STEEL PLATE: 0.25” Thick, Low Carbon Steel, Hot Rolled
A36
POL/POF METAL DECK: 22 Gauge G60 Galvanized Raised Rib
A653
COMPOSITE: Fiber Reinforced Polyester Resin
Molded Vertical Support Gussets
Color: Gray
Weight Density: 1.5 Pounds Per Square Foot (Average)
Tensile Strength: PSI 10,000 @ 45% Styrene
D638
This data is composite of manufacturers data of raw goods and current industry ratings of such goods.
Craigg Mfg. assumes no responsibility for any possible errors in these ratings and believes this data to be correct at this printing.
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 1-2
^ğȕǢǻŷNJ
Features
That Make Us Your First Choice:
iAttractively Finished Aluminum
Frame Mounted Within A Steel
Structural Frame
iAdjustability Allowing Frame
& Cover To Compensate For
Uneven Floor and Different
Floor Covering Material
iHighly Durable Composite Liner
That Will Provide A Lifetime Of
Service
iVast Selection Of Unit Sizes,
Cover Sizes And Cover Styles
iSteel Securing Rods That Holds
The Unit In Alignment During
Installation
Patent 5.412.911
T
he ADJUSTOR is a unitized in-floor pit enclosure that allows access to
refrigeration, electrical, plumbing, pumps and many other
mechanicals. It’s unitized construction provides for a One
Step installation that’s quick and easy, which directly
relates to a labor savings. Installers like its workability and
ease of handling. If penetrations are required they will not
compromise the liner strength.
No special site preparation is needed, just place the unit on a
solid substrate base that’s free of piercing objects. Securing
rods stabilize the unit until backfilled and the concrete floor is
poured.
Fig. 2.2
FRAME AND COMPOSITE LINER ASSEMBLY
Positive alignment of the liner is not necessary
when setting. The aluminum frame can be
adjusted to be fine tuned for uneven floors and
flooring materials by raising and leveling to
match the surrounding conditions.
Covers can be selected from our numerous variety
of sizes, materials, styles and offsets available.
Provided in steel or lightweight aluminum and then
finished to match any type floor covering .
INSTALLATION BEFORE
INSTALLATION
BEFORE Fig. 2.1
POURING FLOOR
Fig. 2.1
POURING FLOOR
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 2-1
NŸŘǣǼNjȖOǼÞŸŘ^sǼÞĶ
FRAME AND COMPOSITE LINER ASSEMBLY
3
4
2
POURED FLOOR LINE
B
ALUMINUM FRAME
& COVER
A
POURED FLOOR LINE
MINIMUM SETTING
MAXIMUM SETTING
E
ADJUSTABLE TO...
C
D
COMPOSITE LINER
Fig. 2.3
DIMENSIONAL INFORMATION
Liners are offered in an almost unlimited selection of sizes from 12” x 12” x 15” deep to 60” x 60” x 36” deep.
er sizes are available upon special request. Liners are available in six inch increments in any direction.
Oth-
INTERIOR WIDTH OR LENGTH OF COMPOSITE LINER "A" OR "B"
NOMINAL SIZE
12"
18"
24"
30"
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
ACTUAL SIZE
12-13/16"
18-3/4"
24-7/8"
30-3/4"
36-11/16"
42-5/8"
48-9/16"
54-1/2"
60-7/16"
66-3/8"
72-5/16"
78-1/4"
84-3/16"
90-1/8"
96-1/16"
24"
30"
36"
21-3/4"
27-3/4"
33-3/4"
OVERALL DEPTH OF COMPOSITE LINER - "C"
13"
* 15"
18"
DIMENSIONS MAY VARY DUE TO MOLD CONFIGURATION.
12” x 12” IS ONLY AVAILABLE IN 15” DEPTH.
USEABLE DEPTH OF COMPOSITE LINER - "D"
10-3/4"
* 12-3/4"
15-3/4"
THE ALUMINUM FRAME HAS AN ADJUSTMENT RANGE OF 2” TO
ALLOW FOR SETTING VARIABLES, UNEVENLY POURED
FLOORS AND FLOOR COVERING MATERIALS.
ACTUAL OPENING OF FRAMEW ORK - "E" - IS 3-1/2" LESS THAN ACTUAL SIZE OF W IDTH OR LENGTH
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 2-2
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
I
nstallation
can be accomplished in several ways. The
preferred way takes advantage of ADL’s adjusting feature.
P lac e a nd lev el t h e u nit w it h t he top e d ge of t he fi ni sh ed a lu minu m f r am e ev en w i t h
the p ropo s ed f in al po ured floo r. T hi s
al low s fo r con c r ete f ini sh e rs t o p ro duc e
a cl e an an d lev el f lo o r a roun d t h e un it ’ s
f r am e. Aft e r t he co nc ret e c ur e s, ev enl y
t urn t h e ad ju st o rs on t h e un de r si de of t h e
fr am e to ra i se it out of th e con c r et e t o a
lev el t h at mat ch e s your c hoi c e o f f loo ri n g
mat e ri al .
POURED FLOOR LINE
ADJUST FOR FLOORING
MATERIAL AFTER POUR
A n a lte rn at iv e m eth od i s to l ev el th e
fr am e’ s t op ed ge to i ts f in al e l ev at ion ,
inc lud ing t h e f loo r in g m at er i al . Pou r
and f in i sh t he con cr e t e t o a lev el
al low in g f o r t h e f lo or in g m at e r ia l .
SELECT COVER IN SECTION 8
FRAME
POURED FLOOR
FRAME ANCHOR
WITH THE UPPER FRAME BEING
ADJUSTABLE UPWARD AS MUCH
AS 2 INCHES,LESS ACCURACY
IS REQUIRED WHEN SETTING
THE LINER.
MUST BE CAST IN CONCRETE
FINE AGGREGATE OR SAND
COMPOSITE LINER
THE LINER TOP FLANGE CAN
RANGE FROM 3/4" TO 2" BELOW
THE FINISH POUR LINE.
LINER SECURING RODS
EARTH
Fig. 2.4
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 2-3
ƻŷȕNJŷərNJ
®ŸNjƻŷȕNJr^NŷərNJ
Features
That Make Us Your First Choice:
iSteel Structural Frame with
Supporting Concrete Anchors
iWood Pour Stop Included for
Concrete Finishing
Convenience
iHighly Durable Composite Liner
That Will Provide A Lifetime Of
Service
iVast Selection Of Unit Sizes
iSteel Securing Rods That Holds
The Unit In Alignment During
Installation
iOptional Ribbed Steel to
Support Poured Cover or a
Non-Load Bearing Removable
Closeoff
T
he Pourover is a unitized in-floor pit enclosure that
allows access to refrigeration, electrical, plumbing,
pump and many other mechanicals. Its unitized
construction provides for a One Step installation
that’s fast and easy, reducing your labor cost. Installers
like its workability and ease of handling. Cutting
etrations will not compromise the liner strength.
No special site preparation is needed, just place the unit
on a solid substrate base that’s free of piercing objects.
Securing rods stabilize the unit until backfilled and
the concrete floor is poured.
pen-
Fig. 3.2
FRAME AND COMPOSITE LINER ASSEMBLY
The provided wood pourstop creates a concrete stop to prevent wet concrete from entering the unit.
The provided blocking is designed to allow for a 4” poured cap if it is to be used. The pourstop has been
designed with a 10 degree taper, this helps avoid settlement of the cap at a future time.
Model POL combines the frame and liner assembly that can, with the use of a ribbed steel cover, create a
completely hidden unit. After all necessary work has been performed in the unit, a concrete cap is
poured over the opening forming a non-accessible enclosure.
Unit can also be left accessible through a non-load bearing galvanized steel closeoff.
Covers available are 22 gauge galvanized ribbed decking , (concrete pour), and 20 gauge galvanized
steel closeoff.
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-6780-8201
E-mail: [email protected]
www.CRAIGG.com
Section 3-1
NŸŘǣǼNjȖOǼÞ
®ŸNjƻŷȕNJr^NŷərNJ
E
NIZ
VA FF
AL
O
. G OSEA
0 G E CL
L
L2
NA VAB
O
TIO
OP REM
R
FO
G
KIN OVER
EC
C
L D RED
E
E
ST POU
R
FO
A
TO BE REMOVED
AFTER POUR
B
POURED FLOOR LINE
P
OD
WO R STO
POU
1-1/2"
E
Useable area.
All access must be
within this area
C
D
COMPOSITE LINER
Fig. 3.3
DIMENSIONAL INFORMATION
Liners are offered in an almost unlimited selection of sizes from 12” x 12” x 15” deep to 60” x 60” x 36” deep.
er sizes are available upon special request. Liners are available in six inch increments in any direction.
INTERIOR WIDTH
OR LENGTH OF COMPOSITE LINER
Oth-
"A" OR "B"
NOMINAL SIZE
12"
18"
24"
30"
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
ACTUAL SIZE
12-13/16"
18-3/4"
24-7/8"
30-3/4"
36-11/16"
42-5/8"
48-9/16"
54-1/2"
60-7/16"
66-3/8"
72-5/16"
78-1/4"
84-3/16"
90-1/8"
24"
30"
36"
21-3/4"
27-3/4"
33-3/4"
OVERALL DEPTH OF COMPOSITE LINER - "C"
13"
* 15"
18"
DIMENSIONS MAY VARY DUE TO MOLD CONFIGURATION.
USEABLE DEPTH OF COMPOSITE LINER - "D"
10-3/4"
* 12-3/4"
15-3/4"
12” x 12” IS ONLY AVAILABLE IN 15” DEPTH.
ACTUAL OPENING OF FRAMEWORK - "E" - IS 3-1/2" LESS THAN ACTUAL SIZE OF WIDTH OR LENGTH
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 3-2
®ŸNjƻŷȕNJr^NŷərNJ
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
WOOD FORM
SET TO FINISH FLOOR HEIGHT
POURED FLOOR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
FINE AGGREGATE OR SAND
COMPOSITE LINER
LINER SECURING RODS
EARTH
Fig. 3.3
POURED CONCRETE COVER
POURED FLOOR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
FINE AGGREGATE OR SAND
STEEL DECKING
COMPOSITE LINER
LINER SECURING RODS
EARTH
Fig. 3.4
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 3-3
^ğȕǢǻŷNJ
®NJōr˓NŷərNJ
Features
That Make Us Your First Choice:
iAttractively Finished Aluminum
Frame Mounted Within A Steel
Structural Frame
iVast Selection of Cover
Designs, Sizes, Material
iStructural Steel Base Frame
with Anchors for Casting
Directly into Floor
iAdjustability Allowing Frame
& Cover To Compensate For
Uneven Floor and Different
Floor Covering Material
iFull Perimeter Sealing Gasket
ADJUSTABLE ASSEMBLY TO BE USED WITH
ON-SITE CONSTRUCTED PITS
The Adjustor Frame and cover assembly is designed
to be mounted on top of a field designed and
built pit. It has all the adjustability features as our
Model ADL that’s would mount in our composite
liner. The structural steel frame with its anchors,
rests on top of the field constructed pit walls and
will cast directly into the poured floor. It is the
ideal frame assembly to be utilized with field designed and built enclosures allowing access to
refrigeration, electrical, plumbing, pump and
many other mechanicals.
Fig. 4.1
FRAME ASSEMBLY
Positive alignment of the frame is not necessary when setting. The aluminum frame can be fine tuned later
for levelness and floor cover matching by raising and leveling the exposed frame to match surrounding
conditions.
Covers can be selected from the numerous variety of sizes, materials, styles and offsets. Available in
steel or lightweight aluminum and then finished to match any type floor covering .
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 4-1
^ğȕǢǻŷNJ
®NJōr˓NŷərNJ
ADJUSTABLE ASSEMBLY TO BE USED WITH
NŸŘǣǼNjȖOǼÞŸŘ^sǼÞĶ
ON-SITE CONSTRUCTED PITS
AT MINIMUM ADJUSTMENT
A
B
POURED FLOOR LINE FOR 1/8" VINYL TILE
SELECT COVERS FROM SECTION 8
E
27
8
ADJUSTOR NUT
FRAME SHOWN AT MINIMUM
PLACEMENT AND ADJUSTMENT
THIS IS THE MINIMUM
PLACEMENT OF THE BASE FRAME
BELOW FINISHED FLOOR IF 1/8"
VINYL TILE IS TO BE USED
JAM NUT
FORMING SUPPORT TAB
Fig. 4.2
AT MAXIMUM ADJUSTMENT
SELECT COVERS FROM SECTION 8
POURED FLOOR LINE FOR 1/2" QUARRY TILE
ADJUSTOR NUT
4
C
FRAME SHOWN AT MAXIMUM
PLACEMENT AND ADJUSTMENT
JAM NUT
THIS IS THE MAXIMUM
PLACEMENT OF THE BASE FRAME
BELOW FINISH FLOOR IS 1/2"
QUARRY TILE IS TO BE USED
FORMING SUPPORT TAB
D
Fig. 4.3
INSIDE OF PIT WALL OR WOOD FORMING MATERIAL
DIMENSIONAL INFORMATION
W IDTH OR LENGTH OF ALUMINUM FRAME "A" OR " B"
NOMINAL SIZE
12"
18"
24"
30"
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
ACTUAL SIZE
11-7/8"
17-13/16"
23-3/4"
29-11/16"
35-5/8"
41-9/16"
47-1/2"
53-7/16"
59-3/8"
65-5/16"
71-1/4"
77-3/16"
83-1/8"
89-1/16"
95"
39-11/16"
47-5/8"
51-9/16"
57-1/2"
63-7/16"
69-3/8"
75-5/16"
81-1/4"
87-3/16"
93-1/8"
WIDTH OR LENGTH OF INSIDE WALL OF FIELD FORMED PIT - "C" OR "D"
10"
15-15/16"
21-7/8"
27-13/16"
33-3/4"
ACT UAL OPENING OF FRAMEW ORK - "E" - IS 2-1/2" LESS T HAN ACT UAL SIZE OF WIDT H OR LENGT H
Manufactured sizes shown. Custom sizes also available.
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 4-2
®NJōr˓NŷərNJ
ADJUSTABLE ASSEMBLY TO BE USED WITH
ON-SITE CONSTRUCTED PITS
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
Formed Monolithic
FRAME ASSEMBLY
(SET TOP EDGE FLUSH WITH THE TOP OF
THE POURED FLOOR LINE) ADJUST FRAME
TO PROPER HEIGHT AFTER FLOOR IS POURED
TO ACCOMMODATE THE FLOORING MATERIAL
LEAVE PROTECTIVE FILM ON THE
ALUMINUM FRAME FOR PROTECTION
MONOLITHIC POUR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
PIT DEPTH DESIGN
BY OTHERS
FORMING SUPPORT TAB
BEND DOWN TO SECURE FRAME
FINE AGGREGATE OR SAND
SPACING BLOCK
PLYWOOD FORMS
Remove inner form after pour
Outer form can be eliminated
PRE-POURED
CONCRETE PAD
Fig. 4.4
EARTH
Concrete Block
Pit
FRAME ASSEMBLY
(SET TOP EDGE FLUSH WITH THE TOP OF
THE POURED FLOORLINE) ADJUST FRAME TO
PROPER HEIGHT AFTER FLOOR IS POURED TO
ACCOMODATE FLOORING MATERIAL
LEAVE PROTECTIVE FILM ON THE
ALUMINUM FRAME FOR PROTECTION
CONCRETE POUR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
FINE AGGREGATE OR SAND
FORMING SUPPORT TAB
PIT DEPTH DESIGN
BY OTHERS
CONCRETE BLOCK
EARTH
PRE-POURED
CONCRETE PAD
Fig. 4.5
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 4-3
NJݵÝ^NǢǻ
RIGID FRAME ASSEMBLY TO BE USED WITH
ON-SITE CONSTRUCTED PITS
Features
®NJōr˓NŷərNJ
That Make Us Your First Choice:
iFastener Free Cover rest into the deep setting frame
channel eliminating the need
for mechanical fasteners
iAttractively Finished Aluminum
frame with in-fitting cover choices
iSecuring Anchors that secures
frame firmly in the concrete floor
pour
iVast Selection of Cover
Designs, Sizes, Material Substrates
iFull Perimeter Sealing Gasket
CASTS DIRECTLY INTO THE POURED
CONCRETE FLOOR
The RigidCast Frame and cover is a straight forward
designed frame that casts directly into a poured
floor or can be utilized with field designed and
built enclosures. It is the ideal unit to allow
access to refrigeration, electrical, plumbing,
pump and many other mechanicals Choose this
unit when a straight forward approach is needed.
Fig. 5.1
FRAME ASSEMBLY
Its unitized construction provides for a One Step
installation that’s fast and easy. Securing anchors provides support to the frame for a more secure cover
loading. The aluminum finish will prove to be attractive and maintenance free for years ahead.
Covers can be selected from the numerous variety of sizes, materials, styles and offsets. Available in
steel or lightweight aluminum and then finished to match any type floor covering .
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 5-1
NJݵÝ^NǢǻ
®NJōr˓NŷərNJ
NŸŘǣǼNjȖOǼÞŸŘ^sǼÞĶ
RIGID FRAME ASSEMBLY TO BE USED WITH
ON-SITE CONSTRUCTED PITS
CASTS DIRECTLY INTO THE POURED
CONCRETE FLOOR
A
ADJUST TO THE THICKNESS
OF THE FLOORING MATERIAL
WHEN FORMING IN
B
SELECT COVERS FROM SECTION 8
E
31
2
C
15
16
D
Fig. 5.2
DIMENSIONAL INFORMATION
W IDTH OR LENGTH OF ALUMINUM FRAME "A" OR " B"
NOMINAL SIZE
12"
18"
24"
30"
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
ACTUAL SIZE
11-7/8"
17-13/16"
23-3/4"
29-11/16"
35-5/8"
41-9/16"
47-1/2"
53-7/16"
59-3/8"
65-5/16"
71-1/4"
77-3/16"
83-1/8"
89-1/16"
95"
39-11/16"
47-5/8"
51-9/16"
57-1/2"
63-7/16"
69-3/8"
75-5/16"
81-1/4"
87-3/16"
93-1/8"
WIDTH OR LENGTH OF INSIDE WALL OF FIELD FORMED PIT - "C" OR "D"
10"
15-15/16"
21-7/8"
27-13/16"
33-3/4"
ACT UAL OPENING OF FRAMEW ORK - "E" - IS 2-1/2" LESS T HAN ACT UAL SIZE OF WIDT H OR LENGT H
Manufactured sizes shown. Custom sizes also available.
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 5-2
NJݵÝ^NǢǻ
®NJōr˓NŷərNJ
RIGID FRAME ASSEMBLY TO BE USED WITH
ÝŗǢǻĵĵǻÝŷŗ^rǻÝĵ
ON-SITE CONSTRUCTED PITS
Formed Monolithic
ALLOW PROPER CLEARANCE
FOR FLOORING MATERIAL
FRAME
MONOLITHIC POUR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
PIT DEPTH DESIGN
BY OTHERS
FINE AGGREGATE OR SAND
SPACING BLOCK
PLYWOOD FORMS
Remove inner form after pour
Outer form can be eliminated
PRE-POURED
CONCRETE PAD
Fig. 5.3
EARTH
Concrete Block
ALLOW PROPER CLEARANCE
FOR FLOORING MATERIAL
FRAME
CONCRETE POUR
USE EITHER
METHOD
FRAME ANCHOR
NAILER
MUST BE CAST IN CONCRETE
FINE AGGREGATE OR SAND
PLYWOOD FORMS
CONCRETE BLOCK
PIT DEPTH DESIGN
BY OTHERS
EARTH
PRE-POURED
CONCRETE PAD
Fig. 5.4
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 5-3
NJݵÝ^NǢǻǻNJȕǢNNJrr^
®NJōr˓NŷərNJ
RIGID FRAME ASSEMBLY TO BE USED WITH
ON-SITE CONSTRUCTED PITS
Features
That Make Us Your First Choice:
iAttractively Finished Aluminum
frame with in-fitting cover choices
iAttached Flange around the
perimeter provides a
screed guide for a perfectly
level finished edge.
iSecuring Anchors that secures
frame firmly in the concrete floor
iFull Perimeter Sealing Gasket
iVast Selection of Cover
Designs, Sizes, Material
CASTS DIRECTLY INTO THE
CONCRETE POUR
The RigidCast TruScreed Frame and cover is a
straight forward designed frame with the
added feature of a finishing guide around its
perimeter. The unit casts directly into a
poured floor or can be utilized with field designed and built enclosures. It is the ideal
unit allowing access to refrigeration,
Fig. 6.1
electrical, plumbing, pump and many other
mechanicals. To help eliminate the problem
of finishing floors evenly around floor frames
we built the needed flooring material thickness into a finishing guide angle. When you order the unit with
the required offset we provide a perfect edge for concrete finishing.
Covers can be selected from the numerous variety of sizes, materials, styles and offsets. Available in steel
or lightweight aluminum and then finished to match any type floor covering .
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 6-1
NJݵÝ^NǢǻǻNJȕǢNNJrr^
®NJōr˓NŷərNJ
RIGID FRAME ASSEMBLY TO BE USED WITH
ON-SITE CONSTRUCTED PITS
NŸŘǣǼNjȖOǼÞŸŘ^sǼÞĶ
CASTS DIRECTLY INTO THE POURED
CONCRETE FLOOR
A
OFFSET IS MANUFACTURED
IN FOR ANY THICKNESS
OF FLOORING MATERIAL
UP TO 1/2" THICK
B
SELECT COVERS FROM SECTION 8
POURED FLOOR LINE
FINISH FLUSH WITH
METAL GUIDE
E
31
2
C
15
16
D
Fig. 6.2
DIMENSIONAL INFORMATION
W IDTH OR LENGTH OF ALUMINUM FRAME "A" OR " B"
NOMINAL SIZE
12"
18"
24"
30"
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
ACTUAL SIZE
11-7/8"
17-13/16"
23-3/4"
29-11/16"
35-5/8"
41-9/16"
47-1/2"
53-7/16"
59-3/8"
65-5/16"
71-1/4"
77-3/16"
83-1/8"
89-1/16"
95"
39-11/16"
47-5/8"
51-9/16"
57-1/2"
63-7/16"
69-3/8"
75-5/16"
81-1/4"
87-3/16"
93-1/8"
WIDTH OR LENGTH OF INSIDE WALL OF FIELD FORMED PIT - "C" OR "D"
10"
15-15/16"
21-7/8"
27-13/16"
33-3/4"
ACT UAL OPENING OF FRAMEW ORK - "E" - IS 2-1/2" LESS T HAN ACT UAL SIZE OF WIDT H OR LENGT H
Manufactured sizes shown. Custom sizes also available.
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 6-2
NJݵÝ^NǢǻǻNJȕǢNNJrr^
®NJōr˓NŷərNJ
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
RIGID FRAME ASSEMBLY TO BE USED WITH
ON-SITE CONSTRUCTED PITS
Formed Monolithic
BUILT IN CLEARANCE
FOR FLOORING MATERIAL
FRAME
ANGLE AT POURED FLOOR LINE
MONOLITHIC POUR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
PIT DEPTH DESIGN
BY OTHERS
FINE AGGREGATE OR SAND
SPACING BLOCK
PLYWOOD FORMS
Remove inner form after pour
Outer form can be eliminated
PRE-POURED
CONCRETE PAD
EARTH
Fig. 6.3
Concrete Block
BUILT IN CLEARANCE
FOR FLOORING MATERIAL
FRAME
ANGLE AT POURED FLOOR LINE
CONCRETE POUR
USE EITHER
METHOD
FRAME ANCHOR
MUST BE CAST IN CONCRETE
NAILER
FINE AGGREGATE OR SAND
PLYWOOD FORMS
CONCRETE BLOCK
PIT DEPTH DESIGN
BY OTHERS
EARTH
PRE-POURED
CONCRETE PAD
Fig. 6.4
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 6-3
ƻŷȕNJŷərNJ
POUROVER ASSEMBLY TO BE USED WITH
ON-SITE CONSTRUCTED PITS
Features
®NJōrǢǢrōDĵɳ
That Make Us Your First Choice:
iStructural Steel frame for
supporting cover or poured
cap
iSecuring Anchors secures
frame firmly into concrete
floor
iWood pourstop holds back
wet concrete and provides the
needed offset
iCover Selection of 20 gauge
ribbed decking or 20 gauge
galvanized smooth
CASTS DIRECTLY INTO THE
CONCRETE POUR
The Pourover Frame assembly gives support to
floor openings and also creates support for
a poured concrete cover or metal closeoff.
The flanged edge and mounted anchors
allows it to embed firmly into the concrete
floor for greater load bearing.
Fig. 7.1
The provided wood pourstop creates a
concrete stop to prevent cement while
pouring from entering the unit. The provided blocking is designed to allow for a 4” poured cap if it is to
be used. The pourstop has been designed with a 10 degree taper, this helps avoid settlement of the cap
at a future time.
Covers available are 22 gauge galvanized ribbed decking , (concrete pour), and 20 gauge galvanized steel
closeoff
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 7-1
ƻŷȕNJŷərNJ
®NJōrǢǢrōDĵɳ
POUROVER ASSEMBLY TO BE USED WITH
NŸŘǣǼNjȖOǼÞŸŘ^sǼÞĶ
ON-SITE CONSTRUCTED PITS
CASTS DIRECTLY INTO THE
CONCRETE POUR
FO
E
RR
V
MO
AB
LE
O
CL
SE
-O
FF
R
ING
CK C O V E
E
D ED
L
E
R
STE P O U
R
FO
POURED FLOOR LINE
1-1/2"
33
4
TO BE REMOVED
AFTER POUR
P
OD
W O R STO
U
PO
D
A
FORMING SUPPORT TAB
C
Fig. 7.2
B
DIMENSIONAL INFORMATION
INTERIOR W IDTH OR LENGTH OF INSIDE W ALL OF FIELD FORM ED PIT "A" OR "B"
NOMINAL SIZE
12"
18"
24"
30"
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
ACTUAL SIZE
10"
15-15/16"
21-7/8"
27-13/16"
33-3/4"
39-11/16"
47-5/8"
51-9/16"
57-1/2"
63-7/16"
69-3/8"
75-5/16"
81-1/4"
87-3/16"
93-1/8"
33-3/16"
39-1/8"
45-1/16"
51"
56-15/16"
62-7/8"
68-13/16"
75-3/4"
80-11/16"
86-5/8"
92-9/16"
INTERIOR W IDTH OR LENGTH OF FRAME OPENING - "C" OR "D"
9-7/16"
15-3/8"
21-5/16"
27-1/4"
Manufactured sizes shown. Custom sizes also available.
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 7-2
ƻŷȕNJŷərNJ
POUROVER ASSEMBLY TO BE USED WITH
ON-SITE CONSTRUCTED PITS
®NJōrǢǢrōDĵɳ
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
Formed Monolithic
WOOD FORM
SET TO FINISH FLOOR HEIGHT
MONOLITHIC POUR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
FORMING SUPPORT TAB
PIT DEPTH DESIGN
BY OTHERS
BEND DOWN TO SECURE FRAME
FINE AGGREGATE OR SAND
SPACING BLOCK
PLYWOOD FORMS
Remove inner form after pour
Outer form can be eliminated
PRE-POURED
CONCRETE PAD
EARTH
Fig. 7.3
Concrete Block Pit
SET TO FINISH FLOOR HEIGHT
CONCRETE POUR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
FINE AGGREGATE OR SAND
FORMING SUPPORT TAB
PIT DEPTH DESIGN
BY OTHERS
CONCRETE BLOCK
EARTH
PRE-POURED
CONCRETE PAD
Fig. 7.4
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 7-3
ƻŷȕNJŷərNJ
POUROVER ASSEMBLY TO BE USED WITH
ON-SITE CONSTRUCTED PITS
®NJōrǢǢrōDĵɳ
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
Poured Cover Cap In-Place
POURED CONCRETE COVER
CONCRETE POUR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
STEEL DECKING
FINE AGGREGATE OR SAND
Fig. 7.5
Removable 20 Gauge Galvanized Closeoff
(For non load bearing applications)
STEEL CLOSE-OFF
CONCRETE POUR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
20 GA. GALVANIZED
STEEL PLATE
FINE AGGREGATE OR SAND
Fig. 7.6
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 7-4
Bordered Covers provide protection for your flooring
material
DŸNj_sNjs_NŸɚsNjǣ
edges. All of the flooring material becomes recessed into the
protective frame. The cover is reversible, e.g. the 1/4” cover
with an 1/8” offset is the reverse side of the 1/2” offset.
Due to its deep setting
design the
er requires no screws or
teners to secure it in
1
ALU
/4"
M
INU
M
V
CO
ER
S
cov3/8" TILE
fasplace.
ALUM COVER
FRAME
1/8" OFFSET
VINYL TILE
1/4" OFFSET
EPOXY FINISHES
TERRA TILE
O
MC
U
N
MI
LU
A
"
3/8
1/2" TILE
VE
RS
3/8" TILE
ALUM. COVER
FRAME
1/4" OFFSET
EPOXY FINISHES
TERRA TILE
1/8" OFFSET
VINYL TILE
T
"S
4
/
1
EE
L
V
CO
1/4" TILE
1/8" TILE
STEEL COVER
FRAME
1/2" OFFSET
QUARRY TILE
3/8" OFFSET
CERAMIC TILE
MARBLE TILE
1/4" TILE
1/8" TILE
1/2" OFFSET
QUARRY TILE
3/8" OFFSET
CERAMIC TILE
MARBLE TILE
1/4" TILE
1/8" TILE
1/2" TILE
1/2" TILE
ER
S
3/8" TILE
1/2" OFFSET
QUARRY TILE
3/8" OFFSET
CERAMIC TILE
MARBLE TILE
1/4" OFFSET
EPOXY FINISHES
TERRA TILE
1/8" OFFSET
VINYL TILE
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 8-1
®ĶȖǣÌNŸɚsNjǣ
Flush Covers provides a natural metallic finish. Available in a Treadplate pattern or a brushed
mill finish. Covers can add a contrast to the surrounding finish.
With its deep setting
design the cover requires no
screws or fasteners to secure it in place.
1/4" STEEL COVER
ATE
D PL
A
E
TR
3/8" ALUMINUM COVER
1/4" ALUMINUM COVER
FRAME
SH
H
FLUS
FINI
MILL
1/4" STEEL COVER
3/8" ALUMINUM COVER
1/4" ALUMINUM COVER
1/4" STEEL COVER
FRAME
CON
CE
ALED
3/8" ALUMINUM COVER
1/4" ALUMINUM COVER
FRAME
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
Section 8-3
ǻɠŸƻÞsOsNŸɚsNj
Two Piece covers allows the frame to be divided into two standard covers.
This cover arrangement is beneficial when limited access to the opening is needed or
reducing the size of the covers will allow for easier removal.
Any type, finish or style of covers can be paired together.
Cover # 1
Cover # 2
COVER
COMBINATIONS
OPTIONAL CENTER SUPPORT
C
B
A
NOMINAL
FRAM E
LENGTH
ACTUAL
FRAM E
LENGTH
O/O
COVER
#1
COVER
#2
A
A
B
C
24"
23-3/4"
11-7/16"
11-7/16"
30"
29 -11/16"
11-7/16"
17-3/8"
36"
35-1/4"
11-7/16"
23-5/16"
17-3/8"
17-3/8"
42"
41-3/16"
48"
47-1/2"
54"
60"
66"
53-5/8"
59-3/8"
65-5/16"
SEE THE PAGE ON PARTIAL COVERS IF A CUSTOM SIZE IS REQUIRED OR IF
PART OF THE PIT COVER IS TO REMAIN OPEN.
72"
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
71-1/4"
11-7/16"
29-1/4"
17-3/8"
23-5/16"
11-7/16"
35-3/16"
17-3/8"
29-1/4"
23-5/16"
23-5/16"
11-7/16"
41-1/8"
17-3/8"
35-3/16"
23-5/16"
29-1/4"
11-7/16"
47-1/16"
17-3/8"
41-1/8"
23-5/16"
35-3/16"
29-1/4"
29-1/4"
11-7/16"
53"
17-3/8"
47-1/16"
23-5/16"
41-1/8"
29-1/4"
35-3/16"
11-7/16"
59-7/32"
17-3/8"
53-9/32"
23-5/16"
47-1/16"
29-1/4"
41-1/8"
35-3/16"
35-3/16"
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 8-4
NŸɚsNjǢȖƼƼŸNjǼǣ
Cover Supports are recommended on larger covers or those
subjected to heavier loading and/or traffic.
Cover Supports are recommended on covers over 30” square
or on partial covers where one edge does not rest on the frame
and is subject to traffic weight.
COVER PLATE
COVER SUPPORT
TENSION SUPPORT
COVER PLATE STRENGTH RATINGS
LBS. PER SQ. FT.
NOTE:
Pit covers and frames are engineered for light
and medium surface loads that are usually
applied with their indoor use.
COVER
PLATE
THICKNESS
Calculations are based on:
Covers informally loaded.
1/4"
All four edges being supported.
A maximum deflection of L/150 of the short
side. Maximum allowed shear strength is
greater.
Cover supports are used to strengthen plate
and reduce the deflection rate. No strength
ratings are available for this configuration.
3/8"
SHORTEST SPAN
LONGEST
SPAN
1'-0"
1-6"
2'-0"
2'-6"
3'-0"
3'-6"
1'-0"
1959
1-6"
1022
580
2'-0"
778
355
245
2'-6"
705
274
160
124
3'-0"
648
230
130
88
72
3'-6"
633
216
109
72
55
46
4'-0"
619
202
94
60
45
36
1'-0"
6610
1-6"
3485
1960
2'-0"
2650
1210
820
2'-6"
2400
922
550
415
3'-0"
2200
785
430
300
245
3'-6"
2140
720
360
245
187
155
4'-0"
2100
691
317
202
151
121
4'-0"
30
104
Craigg Manufacturing assumes no responsibility for the accuracy or completeness of these tables which are supplied solely as a convenience to the user.
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 8-6
^ĵˀ^®
The TWO PART frame consist of two independent adjustable frames
that fit into one base frame. Two smaller frames and covers can be
used for gaining access that will not compromise the units strength.
This is especially beneficial when part of the unit is inaccessible in its
location. Each frame can be independently adjusted to accommodate
differences in flooring type thicknesses. The TWO PART frame adds
flexibility in that both frames do not have to be of equal size.
Two Part
Frame Assembly
Any cover type and style can be used independently along with partial
covers on the Two Part Frame
Available with Liner or Frame Only
Fig. 9.1
Install as you would the MODEL ADL in Section 2 if a liner is utilized or the MODEL ADF in Section 4 if for the frame
only
Sizing unit
is accomplished by :
FIRST by selecting the overall frame size needed using the dimension information chart of the Model ADF section
4-2
SECOND by selecting the aluminum frame sizes needed for the both halves from Model RCF section 5-2. Each half
can be of a different size totaling the overall dimension.
THIRD Choose the approvable cover size and type from Cover section 8-1, 8-2, 8-3
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 9-1
The two part frame consist of two independent
^ĵˀ^®
adjustable frames that fit into one
base frame. Two smaller frames and covers can be used for gaining access that will
not compromise the units strength this is especially beneficial when part of the unit
is inaccessible. Each frame can be independently adjusted to accommodate differences in flooring type.
Two Part
Frame Assembly
NŸŘǣǼNjȖOǼÞŸŘ^sǼÞĶ
Partial covers can also be used in conjunction with the Two Part Frame
A
POURED FLOOR LINE
B
C
SELECT COVERS FROM SECTION 8
SELECT COVERS FROM SECTION 8
ADJUSTOR NUT
ADJUSTOR NUT
JAM NUT
JAM NUT
STEEL BASE FRAME
CAN BE SET FROM
2-7/8" TO 4" BELOW
FINISHED FLOOR LINE
POURED FLOOR LINE
FRAME SHOWN AT
MINIMUM ADJUSTMENT
FORMING SUPPORT TAB
D
E
Inside of Pit Wall
Fig. 9.2
BOTH FRAMES DO NOT HAVE TO BE OF EQUAL SIZE OR COVER STYLE
For Installation of this unit use the ADL in section 2 or the ADF in section 4
DIMENSIONAL INFORMATION
W IDTHOR LENGTH OF ALUMINUM FRAM E
"A" OR "B" OR "C"
NOMINAL SIZE
12"
18"
24"
30"
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
ACTUAL SIZE
11-7/8"
17-13/16"
23-3/4"
29-11/16"
35-5/8"
41-9/16"
47-1/2"
53-7/16"
59-3/8"
65-5/16"
71-1/4"
77-3/16"
83-1/8"
89-1/16"
95"
47-5/8"
51-9/16"
57-1/2"
63-7/16"
69-3/8"
75-5/16"
81-1/4"
87-3/16"
93-1/8"
W IDTHOR LENGTH OF INSIDE W ALL OF FIELD FORMED PIT - "D" OR "E"
10"
15-15/16"
21-7/8"
27-13/16"
33-3/4"
39-11/16"
Manufactured sizes shown. Custom sizes also available.
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 9-2
ƻĵ
Combination Adjustor and Pourover
Frame & Liner
The APL unit is designed for areas that have limited available access area but requires the need for a larger pit. The
first half utilizes our standard Model ADL frame with your choice of cover type, the balance of the unit is tied in with the
poured floor.
Available with Liner or Frame Only
Units are available in nominal 6 inch increments in length ,width
and depth.
Sizing unit
is accomplished by :
FIRST by selecting the overall unit size needed using either the
dimension information chart of the Model ADL section 2-2 or the
Model POL section 3-2.
COVER
SECOND selecting the aluminum frame size needed for the
accessible side from Model RCF section 5-2.
THIRD Choose the cover size and type from Cover section 8-1, 2, 3
NŸŘǣǼNjȖOǼÞŸŘ^sǼÞĶ
LEAVE PROTECTIVE FILM ON THE
ALUMINUM FRAME FOR PROTECTION
Fig. 9.1
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
CONTINOUS POUR
ALLOW PROPER CLEARANCE
COVER AREA
FOR FLOORING MATERIAL
CONTINOUS POUR COVER
POURED FLOOR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
20 GA. GALVANIZED
FINE AGGREGATE OR SAND
20 GA. GALVANIZED
COMPOSITE LINER
LINER SECURING RODS
EARTH
Fig. 9.2
Fig. 9.3
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 9-3
ƻ^
Angled Adjustor and Pourover
Frame & Liner
The APD unit is designed for areas that would
benefit from the unit placed at an angle. The larger pit allows for ample working space and better under ground access.
The triangular finished frame is placed 90 degrees to the setting position. The accessible frame section utilizes our
standard Model ADL frame with your choice of cover type, the balAvailable with Liner or Frame Only
ance of the unit is tied in with the poured floor.
Units are available in nominal 6 inch increments in length ,width
and depth.
Sizing unit
is accomplished by :
FIRST by selecting the overall unit size needed using either the
dimension information chart of the Model ADL section 2-2 or the
Model POL section 3-2.
COVER
POUR OVER
A
A
SECOND by selecting the aluminum frame size needed for the
accessible side.
THIRD Choose the cover size and type from Cover section 8-1,2,3
Fig. 9.1
CHOOSE A COVER
NŸŘǣǼNjȖOǼÞŸŘ^sǼÞĶ
LEAVE PROTECTIVE FILM ON THE
ALUMINUM FRAME FOR PROTECTION
POUR OVER
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
CONTINOUS POUR
ALLOW PROPER CLEARANCE
COVER AREA
FOR FLOORING MATERIAL
CONTINOUS POUR COVER
POURED FLOOR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
20 GA. GALVANIZED
FINE AGGREGATE OR SAND
20 GA. GALVANIZED
SECTION A-A
COMPOSITE LINER
LINER SECURING RODS
EARTH
Fig. 9.2
Fig. 9.3
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 9-4
ƻ
Double End Adjustor with Pourover
Center Frame & Liner
The APA unit allows access from either end when the center section is obstructed. This pit allows for pass through convenience of mechanicals.
Units are available in any of our nominal sizes in 6 inch increments in length ,width and depth.
Sizing unit is accomplished by :
Available with Liner or Frame Only
FIRST by selecting the overall unit
size needed using either the
dimension information chart of the
Model ADL section 2-2 or the Model
POL section 3-2.
SECOND by selecting the aluminum
frame size needed for both accessible
sides. Each can be different section
3-2 Model RCF can provide this
information
THIRD Choose the cover size and
type from Cover section 8-1,2,3
Fig. 9.1
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
ADL
POURED FLOOR LINE
ADJUST FOR FLOORING
MATERIAL AFTER POUR
ADL
POL
POURED COVER
COVER SELECTION
IN SECTION 8
POURED FLOOR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
FINE AGGREGATE OR SAND
Can remain open using the provided
wood pourstop or poured over
COMPOSITE LINER
LINER SECURING RODS
EARTH
Fig. 9.2
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 9-5
ƻŷ
Combination Adjustor ,Pourover and
Open Area Frame & Liner
The APO unit is designed for areas that
allows a partition wall to cross over the pit . Access at the wall can be either
inside the wall or behind it . This solid base under the wall can then be properly sealed to avoid liquids entering the
pit .The removable cover still makes it accessible.
Units are available in any of our nominal sizes in 6 inch increments in length ,width
and depth.
Available with Liner or Frame Only
Sizing unit
is accomplished by :
SECOND selecting the aluminum frame size needed for
the accessible side from Model RCF section 5-2. then
choose the cover size and type from Cover section 8-1,2,3
WOOD FORM
POURED COVER AREA
FIRST by selecting the overall unit size needed using
either the dimension information chart of the Model ADL
section 2-2 or the Model POL section 3-2.
THIRD In the remaining opening determine the poured
cover size and needed opening area.
Fig. 9.1
NŸŘǣǼNjȖOǼÞŸŘ^sǼÞĶ
WOOD FORM
ALLOW PROPER CLEARANCE
FOR FLOORING MATERIAL
CHOOSE COVER
FOR YOUR NEEDS
POURED COVER
AREA
REMOVE AFTER POUR
OPEN AREA
UNDER WALL
FRAME
POURED FLOOR
FRAME ANCHOR
MUST BE CAST IN CONCRETE
20 GA. GALVANIZED
FINE AGGREGATE OR SAND
FORMING SUPPORT TABS
BEND DOWN AFTER POUR
COMPOSITE LINER
LINER SECURING RODS
EARTH
Fig. 9.2
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 9-6
ƻŷ
POURED COVER AREA
WOOD FORM
POURED COVER AREA
Combination Adjustor ,Pourover and
Open Area Frame & Liner
WOOD FORM
Fig. 9.3
Fig. 9.4
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
WALL
ADL
FRAME ANCHOR
MUST BE CAST IN CONCRETE
POURED COVER
ROOM FOR PIPING
COVER IN PLACE
ROOM FOR PIPING
POURED FLOOR
POL
OPEN
FINE AGGREGATE
OR SAND
Field Supplied
Entry
If Required
COMPOSITE LINER
LINER SECURING ROD
EARTH
Fig. 9.5
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 9-7
ˆɟˇɟĵĵȕŗÝǻǢ
Flush Mounting Unit
Frame & Liner
OR
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
POURED FLOOR
Fig. 9.1
WALL
MODEL POLW
WALL
so that one or more sides will have
The “W” unit design is
a minimum amount of
frame structure to interfere with its
installation against a wall. The prime location for its use is along an exterior foundation wall or a
partition wall. This allows any vertical entrances into the pit to stay tight against the wall. The “W”
unit is available in both MODELS ADL and POL and in all of our manufactured sizes.
MODEL ADLW
FRAME ANCHOR
MUST BE CAST IN CONCRETE
AGGREGATE OR SAND
BUILDING's
POURED FOUNDATION
Field Supplied
Entry
If Required
COMPOSITE LINER
LINER SECURING ROD
EARTH
Fig. 9.2
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 9-8
ōŷ^rĵNĵĵ
Fixed Cover with Frame & Liner
The CLL
is another of our One Step installation units. The CLL’s sim-
pler design proves it still can provide you a solid and attractive
in-floor unit. It does limit the choice of cover types and finishes to Flush
Mill or Treadplate in steel or aluminum. Like all of our units the liner is
made of a heavy composite material that incorporates a sturdy steel
supporting frame. The concrete floor area surrounding pit is poured
flush with the finished cover.
Units are available in all our nominal sizes in 6 inch increments in length, width
and depth.
Size unit from the dimension information chart of the Model ADL
section 2-2
Fig. 9.1
Cover selection is limited to the Cover Styles
shown on Section 8-3
Clear Access Dimensions
Pit Size
A"
18"
17"
24"
23"
Flush Covers
ÝŘǣǼĶĶǼÞŸŘ^sǼÞĶ
A
POURED FLOOR
30"
29"
36"
34 3/4"
42"
41"
48"
47"
54"
53"
60"
59"
66"
65"
72"
71"
FINE AGGREGATE OR SAND
COMPOSITE LINER
EARTH
Fig. 9.2
Craigg Manufacturing Corp.
Manufacturers of In-Floor Access Enclosures
12
Phone: 610-678-8200 Fax: 610-678-8201
E-mail: [email protected]
www.CRAIGG.com
Section 9-9