NP-180
•
FR-5 Laminates and Prepregs, Tg 175 °C (DSC)
•
Exceptional consistent laminate quality due to exclusive use of Nan Ya’s
raw materials
•
Utmost high thermal resistance
•
Superior properties in CAF precarious conditions
•
IPC-4101C specification sheet 23 is applicable
NP-180
Revision Date: April 2011
NAN YA SPECIFICATION SHEET FOR NP-180 - Hot strength retention Epoxy Laminates and Prepregs
SPECIFICATION SHEET #:
FLAME RETARDANT MECHANISM:
FILLERS:
ID REFERENCE:
IPC-4101 / 23
RoHS compliant Bromine, UL94 V-0
N/A
UL/ANSI: FR-5 / 23
LAMINATE DATA SHEET
Laminate Properties
Specification ≥ 0,50 mm
[0,0197 in] 40% RC
Specification < 0,50 mm
[0,0197 in] 50% RC
Typical Value
Specification
Typical Value
Specification
Glass Transition Temperature (Tg) by DSC / TMA
175 ± 5 / 165
5% wt. loss
360
onset wt. loss
355
prior Tg
50 - 70
CTE, z-axis
above Tg
200 - 300
prior Tg
15 - 18
CTE, x/y-axis
above Tg
15 - 18
Thermal Expansion (50 °C - 260 °C) z-axis
TE
3,5
Thermal Conductivity
0,48
λ
T260
> 60
Thermal Resistance: Time to Delamination
T288
> 20
Pressure Cooker Test - 2 hours
pass
(10 s solder dip @ 288 °C)
Thermal Stress 10 s at 288 °C [550,4 °F], minimum
A. unetched
pass
B. etched
pass
CAF Resistance
pass
Peel Strength, minimum
A.
Low profile copper foil and very low profile
copper foil - all copper foil >17µm [0,669 mil] 0,78 [4,50]
B.
Standard profile copper foil
1. after thermal stress (35 µm)
1,40 [8,00]
2. at 125 °C [257 °F]
1,22 [7,00]
3. after process solutions
0,96 [5,50]
C.
all other foil - composite
Volume Resistivity, minimum
5.0*109
A. C-96/35/90
B. after moisture resistance
7,4*109
C. at elevated temperature E-24/150
Surface Resistivity, minimum
5,0*108
A. C-96/35/90
B. after moisture resistance
6,1*108
C. at elevated temperature E-24/150
Dielectric Breakdown, minimum
60
Electric Strength, minimum
40
(laminate & prepreg as laminated)
[1000]
Arc Resistance, minimum
120
Comparative Tracking Index (CTI)
4 / 100 - 174
Permittivity, spec. maximum
A. @ 1MHz
4,38
(laminate & prepreg as laminated)
B. @ 100MHz
4,18
C. @ 1 GHz
4,05
D. @ 2 GHz
4,01
E. @ 5 GHz
Loss Tangent, spec. maximum
A. @ 1MHz
0,020
(laminate & prepreg as laminated)
B. @ 100MHz
0,018
C. @ 1 GHz
0,013
D. @ 2 GHz
0,012
E. @ 5 GHz
Flexural Strength, minimum
A. Length direction
B. Cross direction
-
135 - 185
AABUS
AABUS
pass visual
175 ± 5 / 165
360
355
50 - 70
200 - 300
15 - 18
15 - 18
3,5
0,48
> 60
> 20
pass
135 - 185
AABUS
AABUS
pass visual
pass visual
pass visual
AABUS
pass
pass
pass
pass visual
pass visual
AABUS
AABUS
0,78 [4,50]
1,05 [6,00]
0,80 [4,57]
0,80 [4,57]
AABUS
Decomposition Temperature (Td) TGA
Flexural Strength at elevated temperature, length direction, minimum
Dimensional stability x/y-axis E-0,5/170(R)/E-4/105(TL)
Moisture Absorption, maximum
Flammability
(laminate & prepreg as laminated)
Density (50 % resin content)
0,01 - 0,03
0,30
V-0
1,92
Units
metric
[English]
°C
Test Method
Ref. Para.
(IPC-TM-650)
2.4.25
3.10.1.6
°C
2.4.24.6
3.10.1.8
ppm/°C
2.4.24
3.10.1.11
ppm/°C
2.4.24
3.10.1.11
%
W/mK
2.4.24
Laser Flash
3.10.1.11
-
minutes
2.4.24.1
3.10.1.12
pass visual
-
-
2.4.13.1
3.10.1.2
pass / fail
2.6.25
3.12.1.4
3.9.1.1
AABUS
N/mm [lb/in]
2.4.8
1,50 [8,60]
1,22 [7,00]
0,96 [5,50]
-
1,45 [8,28]
0,90 [5,14]
0,90 [5,14]
AABUS
N/mm [lb/in]
N/mm [lb/in]
N/mm [lb/in]
2.4.8.2
2.4.8.3
2.4.8
3.9.1.1.1
3.9.1.1.2
3.9.1.1.3
106
103
5.0*109
7,4*109
104
103
MΩcm
2.5.17.1
3.11.1.3
104
103
30
[750]
60
5,40
0,035
-
5,0*108
6,1*108
60
120
4 / 100 - 174
4,65
4,41
4,21
4,10
0,019
0,016
0,012
0,011
-
104
103
40
60
5,40
0,035
-
MΩ
2.5.17.1
3.11.1.4
2.5.6
3.11.1.6
3.11.1.7
3.11.2.3
3.11.1.5
3.11.1.1
3.11.2.11
-
515
440
415 [60190]
345 [50040]
310
207 [30020]
< 0,05
0,005 - 0,03
< 0,05
0,10
0,80
V-1 minimum
V-0
V-1 minimum
1,92
-
rating
kV
kV/mm
[V/mil]
s
PLC / V
-
2.5.6.2
2.5.1
ASTM D3638
2.5.5.2
2.5.5.3
2.5.5.9
2.5.5.5
2.5.5.2
2.5.5.3
2.5.5.9
2.5.5.5
3.11.1.2
3.11.2.2
N/mm2 [lb/in2]
2.4.4
3.9.1.3
2
N/mm [lb/in ]
%
%
rating
3
g/cm
2.4.4.1
2.4.39
2.6.2.1
UL94
-
3.9.1.4
3.9.1.2
3.12.1.1
3.10.1.1
-
2
PREPREG DATA SHEET
Prepreg Requirements
1. Shelf Life, minimum (Condition 1/ Condition 2)
2. Reinforcement
3. Volatile content maximum
4. Prepreg Parameters
5. Flammability (as laminated)
6. Other
Typical Value
Specification
Unit
Test Method
Ref. Para.
meets requirements
woven E-glass
0,75
V-0
180 / 90
Days
%
AABUS
rating
AABUS
2.3.19
AABUS
UL94
3.17
3.9.2.8
1.1.7
3.10.2.1
as per IPC-4412 or AABUS
0,75
V-1 minimum
Data shown are nominal values for reference only, no review according MIL-S-13949
*AABUS = As Agreed upon Between User and Supplier.
all Nan Ya laminates are in conformance with RoHS regulations
NP-180
Prepreg NP-180B
Glass Fabric
106
106MR
106HR
1080
1080MR
1080HR
2112
2113
2116
2116MR
2116HR
1506
1506MR
7628
7628MR
7628HR
Resin
Content
[%]
68 ± 3
72 ± 3
74 ± 3
62 ± 3
65 ± 3
68 ± 3
60 ± 3
56 ± 3
50 ± 3
54 ± 3
58 ± 3
48 ± 3
52 ± 3
43 ± 3
47 ± 3
50 ± 3
Resin
Flow
[%]
43 ± 5
47 ± 5
50 ± 5
39 ± 5
44 ± 5
48 ± 5
38 ± 5
32 ± 5
26 ± 5
32 ± 5
38 ± 5
25 ± 5
30 ± 5
20 ± 5
26 ± 5
28 ± 5
Gel Time
@ 170 °C
[s]
150 ± 20
Thickn. after lamination
per ply [µm] 1)
[µm]
29 ± 8
34 ± 8
38 ± 8
53 ± 8
58 ± 8
65 ± 8
75 ± 8
76 ± 10
89 ± 10
99 ± 10
110 ±10
135 ± 10
149 ± 10
157 ± 10
164 ± 10
172 ± 10
1)
Recommended press cycle
@ 1 MHz2)
Dk
4,09
4,27
4,17
4,57
4,55
4,55
4,61
4,67
4,74
4,74
4,71
4,62
4,78
4,70
4,62
4,73
Df
0,017
0,017
0,017
0,016
0,016
0,016
0,016
0,016
0,017
0,016
0,016
0,016
0,017
0,016
0,017
0,017
@ 1 GHz2)
Dk
3,79
4,06
3,90
4,39
4,27
4,27
4,27
4,27
4,36
4,36
4,29
4,24
4,41
4,30
4,31
4,30
Df
0,017
0,016
0,017
0,016
0,015
0,015
0,015
0,016
0,015
0,015
0,016
0,015
0,015
0,015
0,016
0,015
acc. recommended press cycle, 75 % remaining copper, 1 oz
2)
data shown are actual values and are not guaranteed
Revision date: April 2011