Technical Manual
Everest DD66000
ACOUSTIC & ELECTRICAL SPECIFICATIONS:
8 Ohms
• Nominal Impedance
5.5 Ohms @ 85Hz
3.5 Ohms @ 40kHz
500 Watts*
• Max Amp Power
45Hz – 50kHz (–6dB)
• Frequency Response
32Hz – 50kHz (–10dB)
96dB (2.83V @ 1 meter)
• Sensitivity
150Hz (LF1 6dB/Octave)
• Crossover Frequency
700Hz (LF2 24dB/Octave)
20kHz (UHF 24dB/Octave)
SYSTEM COMPONENTS:
• Grille
•
•
•
•
AURAL SWEEP TEST SPECIFICATIONS:
• System Aural Sweep Test 6.0V Input 45Hz to 20kHz
5.0V Input 45Hz to 1kHz
• L.F.1 Aural Sweep Test
5.0V Input 45Hz to 1kHz
• L.F.2 Aural Sweep Test
1.00V Input 700Hz to 20kHz
• H.F. Aural Sweep Test
N/A
• H.F. Aural Sweep Test
PHYSICAL SPECIFICATIONS:
38" x 43-5/8" x 18-1/2"
• Dimensions (H x W x D)
(including feet)
(965mm x 1109mm x 469mm)
302 lb (137kg) (each)
• Weight (without grille)
312 lb (142kg) (each)
• Weight (with grille)
362088-001 (black)
WARRANTY:
362088-002 (white)
• Refer to Warranty Statement packed with each product.
Low-Frequency Transducer 15" (381mm) Pulp-cone woofer
(1501AL) x 2 (362330-001)
* The maximum recommended amplifier power rating will ensure
DC Resistance
9.2 Ohms, ±10%
proper system headroom to allow for occasional peaks. We do not
High-Frequency Transducer 4" (102mm) Beryllium
recommend sustained operation at these maximum power levels.
compression driver (476Be)
(362733-001)
DC Resistance
8.0 Ohms, ±10%
Ultrahigh-Frequency
1" (25mm) Beryllium compression
Transducer
driver (045Be-1) (362366-001)
DC Resistance
3.1 Ohms, ±10%
Crossover Network
361900-004, UHF
361900-003, HF
361900-001, LF1
361900-002, LF2
PACKAGING
3
7
4
5
6
2 PLCS.
2
1
2 PLCS.
Release Date 2006
Discontinued Date XXXX
Everest DD66000
FINISHED ASSEMBLY
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, New York 11797
8/07
Technical Manual
Everest DD66000
WIRING DIAGRAM
Grn
Low-Frequency Driver
362330-001
Strip & Tin
Network
361900-001
Grn/Blk
LF1
F.110
GRY/WHT
Red
Grn
Grn/Blk
Blk
M.250
Right
Left
LF2
F.250
F.205
+1 dB
LF1
M.250
LF Input
0 dB
LF2
F.205
Gray
LF2
LF1
Network
361900-002
Wht
M.250
WHT/BLK
LF2
F.250
Bi-Amp
Normal
F.110
Wht/Blk
Red
F.205
Blk
Wht
Blk
9V
F.110
F.110
Low-Frequency Driver
362330-001
Strip & Tin
Wht/Blk
Cable Tie
HF Input
F.205
UHF
F.205
F.205
.5mm
Network
361900-004
Red
Orn
9V
Ultra-High Frequency Driver
362366-001
F.110
Orn/Blk
Blk
0 dB
-.5 dB
F.110
.5mm
+.5 dB
ORN
HF Level
HF Battery
LF Battery
F.205
Bi-Amp
F.205
F.205
Network
361900-003
Red
Yel/Blk
Red
HF
Wht
High-Frequency Driver
362733-001
Strip & Tin
Cable Tie
F.250
F.110
Yel
Yel
Blk
9V
Blk
F.110
Cable Tie
ORN
F.110
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, New York 11797
8/07
Everest DD66000
Normal
Technical Manual
Everest DD66000
LF1 SCHEMATIC
L1
10mH
HF SCHEMATIC
L2
10mH
Grn
Red
C2
47µf
250V
R101
2.2 megaohm
0.25w
R2
62 ohm
5w
C2
3.9µF
250V
C1
47µF
100V
+
R1
5.1 ohm
5w
Blk
Yel/Blk
R1
39 ohm/5w
R2
39 ohm/5w
R3
39 ohm/5w
Wht
R3
120 ohm
5w
1
R5
C1
47µf
250V
Red
LF1
S1
HF
Level
2
130 ohm
5w
Red
GRN/WHT
3
R6
56 ohm
5w
9V
R7
3 ohms
5w
R4
39 ohm/5w
C3
C4
0.47µf
250V
0.47µf
250V
Yel
L1
2mH
Circuit Board
Grn/Blk
9V
R102
2.2 megaohm
0.25w
9V
L2
0.3mH
9V
C5
75µf
100V
R103
9V
9V
C7
75µf
100V
L5
2mH
C9
6.2µf
250V
R104
9V
2.2 megaohm
0.25w
+
L6
0.5mH
2.2 megaohm
0.25w
C10
6.2µf
250V
C12
2.7µf
250V
R9
5.1 ohm
5w
R10
3.9 ohm
5w
C8
5.1µf
250V
R8
3 ohm
5w
C11
2.7µf
250V
R105
Blk
LF2 SCHEMATIC
L2
2.4mH
C6
5.1µf
250V
2.2 megaohm
0.25w
Blk
L1
4.2mH
L4
2mH
L3
0.26mH
Yel
UHF SCHEMATIC
Gray
Wht
Red
WHT/BLK
C1
82µF
100V
C5
27µF
100V
R101
9V
2.2 megaohm
0.25w
C7
C4
27µF
3.0µF
100V
250V
C2
3.0µF
250V
LF2
C3
82µF
100V
Blk
C6
3µF
250V
R1
R102
9V 62 ohm
2.2 megaohm
5w
0.25w
C8
3µF
350V
R2
120
ohm
5w
9V
R1
0.47 ohm
1w
C1
2µF
250V
Red
+
R101
2.2 megaohm
0.25w 9V
9V
C2
2µF
250V
C3
2.7µF
250V
C4
2.7µF
250V
Orn
R102
2.2 megaohm
0.25w
9V
L1
0.025mH
Circuit Board
L2
0.1mH
C5
0.56µF
100V
F.205
.5mm
+
R2
5.1 ohm
0.5w
Orn/Blk
Wht/Blk
F.110
.5mm
Blk
Blk
Shorting straps, 9 volt batteries:
Remove the front grille; Grille removal is described in the owner’s manual.
All controls, and replacement of the 9 volt batteries, are under the
cover at the center bottom of the front baffle.
All crossover networks (four) are inside the cabinet at various locations
(see exploded view) but none are physically attached or accessed
through the terminal cup at the rear. Woofer removal is necessary.
If terminal cup/port tube ass’y at the rear needs service, the (14)
machine screws all have at nut on the end, inside the cabinet, so at
least one woofer removal is necessary to hold the nuts and prevent
each screw from spinning.
Replacement or service of the UHF driver is accomplished by simply
pushing the UHF housing (port) #25 up vertically with your thumbs, as
it’s held in place with a pin/cup arrangement. All UHF driver components will then be exposed.
Replacement or service of the LF driver requires access through the
woofer opening, following these steps.
NOTE: IT IS RECOMMENDED TWO PERSONS BE INVOLVED IN
DD66000 DISASSEMBLY
1. Lay the loudspeaker down, on its back (drivers facing up), on a
padded surface.
2. Remove the grille; Grille removal is described in the owner’s manual.
3. Remove the (8) Phillips woofer screws holding each woofer; remove
the trim rings.
4. The woofer is best extracted by inserting two 1/4 x 20 (3” or longer)
threaded machine screws into opposite sides of the woofer screw
openings. Thread the bolts into the woofer openings by hand, then
pull upwards, lifting the woofer from the counterbore. Then while
one person supports the woofer, another can remove both connecting wires from the terminals. Set the woofer(s) aside; do not
set it on the front baffle as it may damage the leather cover.
5. The HF driver can now be removed from the cabinet: it is attached
to mounting plate #23 (shown upside-down in the exploded view)
and can be removed by loosening, not removing the (2) wing nuts
#37 (knobs) and dislodging the slotted plate & driver from its position. Then the HF driver can be unbolted from the plate and the
wires removed.
Should the leather cover on the front baffle ever need to be replaced,
after woofer removal the front baffle can be extracted by the removal
of (8) hex bolts at the rear of the baffle; these are not shown in the
exploded view. Work the front baffle out of the cabinet. The leather
cover is glued and stapled to the front baffle. The leather cover is not
available from JBL as a separate part, and a suitable upholstery shop
will need to remove and re-cover the front baffle with a material of
your choice. The leather is described as 0.050” Waterproof Leather
Hide, color Black for all finishes except the white version of the
DD66000, and that leather color is Cashmere.
NOTES UPON REASSEMBLY
• Remember to observe correct polarity when reattaching all driver wires.
• Any cable ties that have been cut will need to be replaced
• One woofer screw, on each woofer, on the extreme right/left sides of
the woofer hole is slightly shorter than the others; assure this screw
is replaced only into its proper hole (#39 in exploded view)
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, New York 11797
8/07
Everest DD66000
TO SERVICE THE DD66000
Technical Manual
Everest DD66000
PARTS LIST EVEREST DD66000
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PART NO.
362088-001
362088-002
362682-001
362913-001
338067-004
338067-005
363207-001
362330-001
362733-001
362366-001
361900-004
361900-003
361900-001
361900-002
361900-005
361900-006
354921-001
18
362685-002
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
361865-002
361795-005
361795-006
361790-002
361796-001
361861-002
361899-002
352363-001
362625-001
362625-002
362625-003
362627-001
338073-001
362063-001
362065-001
362740-001
339976-001
338168-001
362848-001
883-11110-16
39
804-73114-24
DESCRIPTION
QTY.
ASY, GRILLE, BLK (CHERRY,
1
ROSEWOOD, EBONY MODELS)
ASY, GRILLE, WHT (MAPLE MODEL)
1
LOGO
1
OUTER CARTON
1
FOOT, SPIKE, SPKR
4
FOOT, BASE, FLOOR
4
BATTERY 9V
2
DRIVER, HEX, 5/32
1
ASY, WOOFER,SINGLE-PK-1501AL
2
ASY, DRIVER HI-FREQ-476BE
1
TWEETER, UHF-045BE-1
1
NETWORK, UHF
1
NETWORK, HF
1
NETWORK, LF1
1
NETWORK, LF2
1
CTRL BD, LF, NETWORK
1
CTRL BD, HF, NETWORK
1
ASY, PORT TUBE/INPUT
1
TERMINAL ASS’Y
FRONT PANEL CONTROL COVER,
1
CASTING, FNSHD
TRIM RING, 15", PNTD
2
HF HORN LIP, UPPER, PNTD
1
HF HORN LIP, LOWER, PNTD
1
THROAT, HORN, PNTD
1
ADAPTER, THROAT, RAW,
1
HORN, UHF, PNTD
1
HOUSING, UHF, PNTD
1
BUSHING, RUBBER 2452H
6
STUD, THREADED, 1/4-20X3.0"
7
STUD, THREADED, 1/4-20X3.5"
4
STUD, THREADED, 1/4-20X5.5"
5
STUD, THREADED, 5/16-18X3.0"
2
GASKET, DRVR, 15"
2
GASKET, THROAT
2
GASKET, PTB/TERM, FLANGE
1
GASKET, CTRL BD, CAB
2
GASKET, UHF
1
GASKET, FOOT
4
KNOB, 5/16-18, FEMALE
2
SCREW, 8 X 1, FLT, PH, PB,
20
BLK ZINC, LCS CTRL BD
SCREW, 10-32 X 1 1/2, SKT, HEX,
14
AL-2000 BLK WFR/PTB/TERM/CAB
40
804-73114-32
41
806-11010-20
42
833-30100-00
43
883-41110-16
44
883-41110-12
45
802-41010-08
46
804-41110-08
47
806-01000-16
48
844-01110-07
49
834-30010-00
50
51
52
338067-002
338067-003
884-41100-12
53
54
66606-01
337538-001
55
333249-001
56
57
58
59
60
362682-001
363170-001
338166-001
363469-001
073-111010-100ZR
61
184-921200-169ZR
62
072-060418-000ZR
63
072-060186-000ZR
64
072-060187-000ZR
SCREW, 10-32X2, SKT, HEX,
AL-2000 BLK WFR
SCREW, 1/4-20 X 1 1/4, FLT, PH,
UNC, BLK ZNC, L THROAT
NUT, 10-32, KEPS, CLR ZINC, LCS,
RIGHT PTB/TERM
SCREW, 8 X 1, PAN, PH, PB, BLK
ZINC, LCS NTWK/LF1/LF2
SCREW, 8 X 3/4, PAN, PH, PB,
BLK ZINC, LCS NTWK/UHF/HF
SCREW, 6-32 X 1/2, PAN, PH,
BLK ZINC, LCS UHF/HORN
SCREW, 10-32 X 1/2, PAN, PH,
BLK ZINC, LCS UHF/HORN/HSG
SCREW, 1/4-20 X 1, FIL, PH, CLR
ZINC, LCS FOOT/ADPTR
WASHER, 1/4, SAE, REG, BLK ZINC,
LCS LIPS
NUT, 1/4-20, KEPS, BLK ZINC, LCS,
RIGHT LIPS
FOOT, BASE, SPKR
FOOT, SLIDE, SPKR
SCREW, 10 X 3/4, PAN, PH, PB,
CLR ZC, LCS TIE-WRAP
PIN, GRILLE, 7/8, LONGSTEEL, BLK
CUP ,GRILLE, SMALL
(UHF DRIVER HOUSING)
CUP, GRILLE, LARGE
(GRILLE, UHF DRIVER HOUSING)
JBL LOGO
PLUG, FOAM
GSKT, UHF, TOP
PAD, DAMPING, HORN-EVEREST
SHORTING BAR, GOLD PLATED
(CONTROL PANEL)
SHORTING STRAP, WIRE
(MAIN INPUT CUP)
BINDING POST, GOLD PLATED
(CONTROL PANEL)
BINDING POST, GOLD PLATED
(MAIN INPUT CUP) POSITIVE, RED
BINDING POST, GOLD PLATED
(MAIN INPUT CUP) NEGATIVE, BLK
14
4
12
6
8
2
2
8
24
16
4
4
3
4
1
6
1
6
1
2
7
2
21
Everest DD66000
ITEM
1
2
2
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, New York 11797
8/07
Technical Manual
Everest DD66000
EXPLODED VIEW
52
12
28
44
20
57
26
3 PLCS.
43
SECTION
13
B-B
14
43
3 PLCS.
27
UPPER LIP
57
26
57
(BLK)
27
26
12
64
12
61
12
63
(RED)
B
26
57
A
A
21
29
LOWER LIP
B
SCALE
0.500
9
2 PLCS.
2 PLCS.
21 48 49 59
20 48 49 59
55
25
58
46
35
10
45
54
24
47
41
4 PLCS.
32
22
30
23
37
4 PLCS.
55
31
4 PLCS.
4 PLCS.
44
12
8
Everest DD66000
16 34 38
2 PLCS.
39
53
12 PLCS.
11
33
17
39 42
19
53
14 PLCS.
2 PLCS.
36
40
50
47
39
18
56
34 38 15
60 62
4 PLCS.
51
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, New York 11797
8/07