DR4300 / DR4500
Panel Mounting
Instructions
Document Number
Form: 43-DR-33-86
Effective: 2/03
Supersedes: 8/02
Summary
Installation Procedure
•
Mounting Bracket Kit (30755065-502) consists of:
2 – Mounting Bracket, Right Hand
1 – Mounting Bracket, Left Hand
12 – #8-32 x 1/2 Long Pan Head Screws
2 – 1/4-20 x 3/8 Long Hex Head Bolts
1 – 1/4-20 x 3/4 Long Hex Head Bolt, and
3 – 1/4 Lockwashers
1 – Panel Gasket
•
NEMA4X Mounting Bracket Kit (30755065-503) consists of:
4 – Mounting Brackets,
20 – #8-32 x 3/4 Long Pan Head Screws
4 – 1/4-20 x 5/8 Long Hex Head Bolts
4 – 1/4 Lockwashers
1 – Panel Gasket
.
Table 1 – Mounting Bracket (30755065-502) Procedure
Step
Action
1
Place the panel gasket onto the rear flange of the recorder case.
2
Install four #8-32 screws on each of the three mounting brackets so the
ends of the screw threads are flush with the face of the bracket.
NOTE: Screw heads to be on flange side of bracket.
3
Insert the case with gasket into the panel opening.
4
Install one left hand and one right hand bracket with 1/4 x 3/8 long bolts
and lockwashers on each side of the case.
NOTE: The notch on each bracket should be facing upward towards the
top of the unit.
Do not tighten the hex bolts at this time.
5
Install the remaining right hand bracket on the top with the 1/4 x 3/4 long
bolt and lockwasher.
Do not tighten the screw at this time.
43-DR-33-86
Page 1 of 3
Kit Instruction, continued
Step
Action
6
Place a screwdriver blade on the notch of each bracket and firmly tap so
that each bracket firmly mates the case with gasket to the panel. Tighten
the three 1/4 hex bolts to hold the brackets in place.
7
Start to tighten the #8 x 1/2 screws on the right side bracket. Alternate
screws at opposite ends until all four screws have a minimum of 4 lb-in
torque applied. Do the same to both the left side and top brackets.
When completed all twelve screws should have a minimum of 4 lb-in of
torque applied. This assures the case and panel gasket are adequately
sealed against the panel.
Table 2 NEMA4X Mounting Bracket (30755065-503) Procedure
Step
Action
1
Place the panel gasket onto the rear flange of the recorder case.
2
Install five #8-32 x 3/4 screws on each of the four mounting brackets so
the ends of the screw threads are flush with the face of the bracket.
NOTE: Screw heads to be flange side of brackets.
3
Insert the case with gasket into the panel opening.
4
Position the bracket so that the tabs on the end of the bracket slide into
the holes in the case, Secure the four brackets with 1/4-20 x 5/8 long
bolts and lockwashers; one to the top, bottom and each side of the case.
Tighten the bolts.
5
Start to tighten the #8-32 x 3/4 screws on a bracket. Tighten the end
screws first then those toward the middle until all five screws have a 5 to
8 lb-in of torque applied. Do the same to both the other three brackets.
When completed all twenty screws should have a 5 to 8 lb-in of torque
applied. This assures that the case and panel gaskets are adequately
sealed against the panel.
Page 2 of 3
43-DR-33-86
Kit Instruction, continued
Hex Head Bolt
1/4-20 x 5/8 inch
Bracket (4)
Pan Head Screw
8-32 x 3/4 inch
Slot
Slot
Slot
Hex Head Bolt
1/4-20 x 5/8 inch
Slot
Pan Head Screw
8-32 x 3/4 inch
Hex Head Bolt
1/4-20 x 5/8 inch
Side View
NOTE: Mounting brackets, attaching hardware, and panel gasket are included in kit 30755065-503
;
Figure 1 Panel Mounting Recorder with NEMA4X Door
Warranty/Remedy
Honeywell warrants goods of its manufacture as being free of defective
materials and faulty workmanship. Contact your local sales office for
warranty information. If warranted goods are returned to Honeywell
during the period of coverage, Honeywell will repair or replace without
charge those items it finds defective. The foregoing is Buyer's sole remedy
and is in lieu of all other warranties, expressed or implied, including
those of merchantability and fitness for a particular purpose.
Specifications may change without notice. The information we supply is
believed to be accurate and reliable as of this printing. However, we
assume no responsibility for its use.
While we provide application assistance personally, through our literature
and the Honeywell web site, it is up to the customer to determine the
suitability of the product in the application.
Industrial Measurement and Control
Honeywell
1100 Virginia Ave.
Fort Washington, PA 19034
43-DR-33-86 0203 Printed in USA
www.honeywell.com/imc