Decorative Concrete Dye
•
•
•
•
•
•
Interior/Exterior Finish
Water-Based Acid Free Dye
Consistent Color Accuracy
Complete Project Kit
Transform Plain Concrete
Wet-Look Sealer Protects and Enhances Color
WHERE TO USE
Uncoated and unsealed, properly prepared Interior or Exterior concrete
surfaces such as: Patios, Porches, Pavers, Walkways, Kitchens, Bedrooms and
other Concrete Floors.
WHERE NOT TO USE
DO NOT use on areas subject to automotive tires and around swimming
pools. DO NOT apply on surfaces subject to hydrostatic pressure. DO NOT
apply over sealed or waterproofed concrete surfaces. DO NOT use over
previously painted surfaces. DO NOT use over loose or damaged concrete
or if concrete dust is present. Do not use BEHR® D-991 Cleaner & Etcher
(included) on marble, granite, terrazzo, colored concrete, brass, bronze or
copper. If treating surfaces other than concrete, test a small inconspicuous
area before starting project.
PREPARATION †
(Proper surface preparation is required.) New concrete must cure for a
minimum of 30 days. Protect surrounding areas using plastic sheeting or drop
cloths before starting your project. Protect grass and any nearby plants by
dampening with water and covering with plastic. Scrape and sweep away dirt
and loose contaminates on the surface. Refrain from using a power washer
as the power washer may leave permanent marks. Wipe up all excess oil and
grease spills.
FOR EXTERIOR SURFACES: For severe oil or grease stains use a product
such as BEHR PREMIUM® NO. 990 Concrete & Masonry Degreaser & Cleaner.
Remove excess water with a non-metal squeegee or mop. Prevent all rinse
solution from entering storm drain. For proper penetration and adhesion,
use BEHR NO. D-991 Concrete & Masonry Cleaner & Etcher. Wear protective
clothing, goggles and acid resistant rubber gloves & boots. Mix the 1 quart
Cleaner & Etcher into 3 quarts of water using a plastic watering can (do
not use metal can). Stir diluted solution thoroughly and avoid splashing.
Apply Cleaner & Etcher to dry surface and allow product to stand for 10-20
minutes then scrub vigorously. Do not let product dry on the surface. Rinse
surface thoroughly with fresh water while scrubbing at the same time to
properly remove all remaining residue. Once the surface is completely
dry, check for dust or powder residue. Repeat rinsing step if residue is still
present. Important: Failure to completely rinse the concrete surface may
result in adhesion issues. The surface is ready when it feels like medium grit
sandpaper and no residue or loose concrete remains on the surface.
FOR INTERIOR SURFACES: Cover all air vents and ducts before starting the
cleaning process. Remove stain with BEHR PREMIUM NO. 990 and prepare
the surface with BEHR PREMIUM NO. 991 following the steps described under
exterior surfaces. Remove the Cleaner & Etcher residue using a mop and
bucket to minimize the amount of water left on the concrete surface. After
cleaning and removing all the Cleaner & Etcher residue, allow the surface to
completely dry. Once the surface is completely dry, check for dust or powder
residue. Repeat rinsing step if residue is still present. Important: Failure to
completely rinse the concrete surface may result in adhesion issues. The
surface is ready when it feels like medium grit sandpaper and no residue or
loose concrete remains on the surface.
No. 860 Tuscan Stone
No. 862 Desert Oasis
PUMP SPRAYER
Read all assembly and operating instructions carefully before using the pump
sprayer. When not in use, soak the tip of the pump sprayer in water to prevent
the tip from becoming clogged.
APPLICATION
The surface must be clean, dry and free of dust, grease, oil, curing agents and
other contaminants for the Dye to penetrate and adhere properly. Do not thin.
Stir Base Color and Accent Color in can before pouring into the pump sprayer.
Do not apply tape or other adhesives to surfaces that have been coated with
the Dye or Sealer as the adhesives may remove the coatings. Use product
when air and surface temperatures are between 50–90°F. Do not apply
if heavy winds are blowing, or if dew or rain is expected within 24 hours.
Important: Test a small inconspicuous area and allow Dye to dry before
starting your project to ensure color satisfaction. Refer to the instructional DVD
(included) for detailed information and application tips.
BASE COLOR: Fill the pump sprayer with Base Color and fully pressurize.
Tip: Adjust the pump sprayer brass nozzle tip until you reach a fine mist
setting and practice spraying on a piece of cardboard or newspaper. Apply
Base color using a random or figure-eight motion being careful not to create
a pattern on the concrete. Hold the spray tip approximately 10 inches above
the concrete and finely mist on the surface (refrain from covering the concrete
surface with an even, steady stream as this could lead to a monochromatic
look rather than a variegated look). If you need to stop during application step,
use natural break points such as borders, walls or expansion joints. Save any
unused product for future touch-ups. Important: To prevent drips from getting
on the surface, use a rag to catch any drips when stopping the sprayer. Apply
at a spread rate of 175-250 sq. ft. per gallon depending on the porosity and
texture of the surface. Allow Base Color to dry (approx. 1-2 hrs. depending on
temperature and humidity) to the touch before applying the Accent Color. Do
not walk on wet Dye.
ACCENT COLOR: Flush pump sprayer and wand with fresh water. Add Accent
Color to clean pump sprayer and fully pressurize. Apply Accent in the same
method as Base color. Apply Accent Color at a spread rate of 175-250 sq.
ft. per half gallon. Allow Accent Color to dry 24 hours before topcoating with
Wet-Look Sealer.
TOPCOAT: Flush pump sprayer and wand with fresh water. Use Wet-Look
Sealer (included) to protect and enhance the Concrete Dye. Do not thin Sealer.
Stir or gently shake before applying. Fill the pump sprayer with Wet-Look
Sealer and fully pressurize. Apply a thin coat at a spread rate of 150-300
sq. ft. per gallon. Spread rate is highly dependent on surface roughness
and porosity. Allow first coat to dry 4 hours, then apply a thin second coat.
Important: Make sure you apply two very thin coats. Do not over apply the
product or allow the product to puddle as this could lead to the product
drying milky in color. Dries to touch in 1 hour. Longer dry time required in
cooler temperatures and in higher humidity. Floors may be subjected to light
foot traffic after 24 hours. Allow 72 hours before repositioning furniture or
subjecting surface to heavy foot traffic. Wait at least 30 days before cleaning
with a mild, non-abrasive liquid detergent. Caution: Use caution when
shoveling snow or moving sharp or heavy objects across the surface, as this
may damage the Wet-Look Sealer & Concrete Dye. Note: Horizontal surfaces
Decorative Concrete Dye
•
•
•
•
•
•
Interior/Exterior Finish
Water-Based Acid Free Dye
Consistent Color Accuracy
Complete Project Kit
Transform Plain Concrete
Wet-Look Sealer Protects and Enhances Color
No. 860 Tuscan Stone
No. 862 Desert Oasis
may be subject to excessive wear. Use a product such as BEHR PREMIUM
NO. 985 Wet-Look Sealer for periodic touch-ups, to increase gloss level, or for
added protection.
CLEAN UP
Clean with soap and water. Properly dispose of all soiled rags and protect
unused product from freezing. For disposal of empty containers and unused
product contact your household refuse collection service.
MAINTENANCE CLEANING: To keep your project looking great and to remove
dirt build up or efflorescence (efflorescence is a chalky white salt residue
that can occur with cementatious surfaces), clean with a mixture of a product
such as BEHR PREMIUM NO. 991 Concrete & Masonry Cleaner & Etcher and
water. Mix a ratio of 10 parts water to 1 part NO. 991 and apply with a plastic
watering can and bristle broom. For severe hard water staining or severe
efflorescence, use a ratio of 4 parts water to 1 part NO. 991.
TOUCH-UP: (Recommended for areas under 3” in diameter.) For areas
that are chipping or de-laminating use a fine grit sandpaper (220 grit is
recommended) to smooth out the edges. Remove any dirt, dust, or loose
debris surrounding the touch-up area. Using a foam brush or rag (cloth), dab
the affected area using the Base Color. Allow Base Color to dry to the touch.
Repeat application steps using the Accent Color. Alternate between the Base
Color and Accent Color applications until you achieve your desired color. After
both colors are completely dry, apply the Wet-Look Sealer with a foam brush
using a feathering motion (this will help prevent lap marks from the brush).
Allow Wet-Look Sealer to dry and apply a second coat of sealer if necessary.
Note: For areas larger than 3” in diameter use the pump sprayer to apply the
Dyes and Sealer, following the same instructions as above.
WARNING! If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT
WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA vacuum and a wet
mop. Before you start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800-424-LEAD or log on
to www.epa.gov/lead.
†
LIMITED WARRANTY BEHR PROCESS CORPORATION warrants that this product meets
Behr’s manufacturing specifications. If this product does not meet these specifications,
Behr Process Corporation will, at its option and upon proof of purchase, either furnish an
equivalent amount of new product to you or refund the purchase price of this product.
This guarantee excludes (1) labor and costs of labor for application or removal of any
product; or (2) any incidental or consequential damages, whether based on breach
of express or implied warranty, negligence, strict liability or any other legal theory.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you. This warranty gives you specific
legal rights and you may also have other rights, which vary from state to state.
To consult with a BEHR Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).
©2012 Behr Process Corporation
Santa Ana, CA 92704 U.S.A. • behr.com
V.O.C. (C.O.V.) <120 g/L • REV. 07/12
DANGER! CORROSIVE! WILL CAUSE EYE BURNS AND PERMANENT TISSUE
DAMAGE. HARMEFUL IF SWALLOWED. CONTAINS ORGANIC SALT. AVOID
CONTACT WITH SKIN. MAY CAUSE PERMANENT SKIN DAMAGE AND SEVERE
RESPIRATORY SYSTEM IRRITATION. USE WITH ADEQUATE VENTILATION. Wear
protective clothing , acid resistant rubber gloves and eye goggles. Avoid breathing
apray mist. If properly used, a respirator may offer additional protection. FIRST AID:
Eye and skin contact: In case of eye or skin contact, flush immediately with water
for 20 minutes. Get medical attention if irritation or symptoms of overexposure
persist. If inhaled, move to fresh air. If swallowed, DO NOT induce vomiting. Get
medical attention immediately. Give water to dilute material in stomach. Never give
anything by mouth to an unconscious person.
CAUTION: KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.